Poly(1‐butene)/clay nanocomposites: Preparation and properties

The preparation and properties of poly(1‐butene) (PB)/clay nanocomposites are described for the first time. Nanocomposites were prepared with the melt‐intercalation technique, using organically modified clay. The X‐ray diffraction patterns portrayed well‐defined diffraction peaks at higher d‐spacing than pristine clay, confirming the intercalation of polymer in silicate layers. Because PB exhibits time‐dependent polymorphism, the effect of clay on the phase transformation of PB was examined with thermal analysis. The phase transformation from a metastable tetragonal form to a stable hexagonal form was enhanced because of incorporation of layered silicates in the polymer matrix. The nanocomposites exhibited about a 40–140% increase in storage modulus depending on the clay content and significantly lower coefficient of thermal expansion. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1014–1021, 2003     

Effect of a silicate filler on the crystal morphology of poly(trimethylene terephthalate)/clay nanocomposites

A series of intercalated poly(trimethylene terephthalate) (PTT)/clay nanocomposites were prepared in a twin‐screw extruder by the melt mixing of PTT with either quaternary or ternary ammonium salt‐modified clays. The morphology and structure, along with the crystallization and melting behavior, and the dynamic mechanical behavior of the composites were characterized by X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and dynamic mechanical thermal analysis. The results showed that the PTT chains could undergo center‐mass transport from the polymer melt into the silicate galleries successfully during the blending and extrusion process. More coherent stacking of the silicate layers was reserved at higher clay concentrations and shorter blend times. Compared with conventionally compounded composites, the nanoscale‐dispersed organophilic clays were more effective as crystal nucleation agents. The influence of the nanosilicates on the crystallization and melting behavior of PTT became distinct when the concentration of clay was around 3 wt %. The changes in the crystallization behavior of the polymer/clay nanocomposites depended not only on the size of the silicates but also on the intrinsic crystallization characteristics of the polymers. The resulting nanocomposites showed an increase in the dynamic modulus of PTT and a decrease in the relaxation intensity (both in loss modulus and loss tangent magnitude). © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2275–2289, 2003     

Poly(vinylidene fluoride)/clay nanocomposites prepared by melt intercalation: Crystallization and dynamic mechanical behavior studies

The preparation and properties of poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported for the first time. PVDF/clay nanocomposites were prepared by melt intercalation with organophilic clay. The composites were characterized with X‐ray diffraction, differential scanning calorimetry, and dynamic mechanical analysis. X‐ray diffraction results indicated intercalation of the polymer into the interlayer spacing. PVDF in the nanocomposites crystallized in the β form. Differential scanning calorimetry nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity, as evidenced by the melting and crystallization peaks. Isothermal crystallization studies showed an enhanced rate of crystallization with the addition of clay, as evidenced by a reduction in the crystallization time. Dynamic mechanical analysis indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. The tan δ peak signifying the glass‐transition temperature of PVDF shifted to higher temperatures. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1682–1689, 2002     

Intercalated poly(vinylidene fluoride)/clay nanocomposites: Structure and properties

The preparation and characterization of melt‐intercalated poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported. Organophilic clay (clay treated with dimethyl dihydrogenated tallow quaternary ammonium chloride) was used for the nanocomposite preparation. The composites were characterized with X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). XRD results indicated the intercalation of the polymer in the interlayer spacing. The incorporation of clay in PVDF resulted in the β form of PVDF. DSC nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity. Isothermal crystallization studies show an enhanced rate of crystallization with the addition of clay. DMA indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 31–38, 2003     

Effects of clay‐modifying agents on the morphology and properties of poly(methyl methacrylate)/clay nanocomposites synthesized via γ‐ray irradiation polymerization

Via γ‐ray irradiation polymerization, poly(methyl methacrylate) (PMMA)/clay nanocomposites were successfully prepared with reactive modified clay and nonreactive clay. With reactive modified clay, exfoliated PMMA/clay nanocomposites were obtained, and with nonreactive clay, intercalated PMMA/clay nanocomposites were obtained. Both results were confirmed by X‐ray diffraction and high‐resolution transmission electron microscopy. PMMA extracted from PMMA/clay nanocomposites synthesized by γ‐ray irradiation had higher molecular weights and narrow molecular weight distributions. The enhanced thermal properties of the PMMA/clay nanocomposites were characterized by thermogravimetric analysis and differential scanning calorimetry. The improved mechanical properties of PMMA/clay were characterized by dynamic mechanical analysis. In particular, the enhancement of the thermal properties of the PMMA/clay nanocomposites with reactive modified clay was much more obvious than that of the PMMA/clay nanocomposites with nonreactive clay. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3218–3226, 2003     

Preparation and characterization of melt‐compounded polyethylene/vermiculite nanocomposites

Polyethylene (PE)‐layered vermiculite (VMT) nanocomposites were fabricated via direct melt compounding in a twin‐screw extruder followed by injection molding. Exfoliated PE/VMT nanocomposites were readily prepared via in situ melt mixing of maleic anhydride modified VMT with PE. Maleic anhydride acts as either the intercalation agent for VMT or as a compatibilizer for the PE and VMT phases. X‐ray diffraction and transmission electron microscopic observations revealed the formation of exfoliated PE/VMT nanocomposites. The experimental results showed that the storage modulus and strength of nanocomposites tend to increase with an increasing VMT content. Nearly 25.35% increment in the tensile strength and 50% increment in the storage modulus were achieved by incorporating 4 wt % VMT into PE. The thermal properties of the nanocomposites were investigated by dynamic mechanical analysis and differential scanning calorimetry. The glass‐transition temperature of PE/VMT nanocomposites appeared to increase upon the introduction of VMT into the PE matrix. The effects of maleic anhydride addition on the formation of the PE/VMT nanocomposites are discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1476–1484, 2003     

Melt blending of ethylene‐vinyl alcohol copolymer/clay nanocomposites: Effect of the clay type and processing conditions

Ethylene‐vinyl alcohol copolymer (EVOH)/clay nanocomposites were prepared via dynamic melt blending. The effect of the processing parameters on blends containing two clay types in different amounts was examined. The blends were characterized with a Brabender plastograph and capillary rheometer, differential scanning calorimetry, dynamic mechanical thermal analysis (DMTA), X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). XRD showed advanced EVOH intercalation within the galleries, whereas TEM images indicated exfoliation, thereby complementing the XRD data. A dilution process with EVOH and clay treatment in an ultrasonic bath before melt blending did not add to the intercalation level. Different trends were observed for the EVOHs containing two different clay treatments, one claimed to be treated for EVOH and the other for amine‐cured epoxy. They reflected the differences in the amounts of the strongly interacting polymer for the two nanocomposites. Thermal analysis showed that the melting temperature, crystallization temperature, and heat of fusion of the EVOH matrix sharply decreased with both increasing clay content and processing times. Significantly higher viscosity levels were obtained for the blends in comparison with those of the neat polymer. The DMTA spectra showed higher glass‐transition temperatures for the nanocomposites in comparison with those of the neat EVOH. However, at high clay loadings, the glass‐transition temperature remained constant, presumably because of an adverse plasticizing effect of the low moleculared mass onium ions treating the clays. The storage modulus improved when clay treated for EVOH was used, and it deteriorated when amine‐cured epoxy clay was incorporated, except for the sonicated clay. TGA results showed significant improvements in the blends' thermal stability in comparison with that of the neat EVOH, which, according to TEM, was greater for the intercalated structures rather than for exfoliated ones. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1741–1753, 2002     

Preparation and characterization of PP/clay nanocomposites based on modified polypropylene and clay

X‐ray diffraction and differential scanning calorimeter (DSC) methods have been used to investigate the crystallization behavior and crystalline structure of hexamethylenediamine (HMDA)‐modified maleic‐anhydride‐grafted polypropylene/clay (PP‐g‐MA/clay) nanocomposites. These nanocomposites have been prepared by using HMDA to graft the PP‐g‐MA (designated as PP‐g‐HMA) and then mixing the PP‐g‐HMA polymer in hot xylene solution, with the organically modified montmorillonite. Both X‐ray diffraction data and transmission electron microscopy images of PP‐g‐HMA/clay nanocomposites indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into PP‐g‐HMA matrix. DSC isothermal results revealed that introducing 5 wt % of clay into the PP‐g‐HMA structure causes strongly heterogeneous nucleation, which induced a change of the crystal growth process from a three‐dimensional crystal growth to a two‐dimensional spherulitic growth. Mechanical properties of PP‐g‐HMA/clay nanocomposites performed by dynamic mechanical analysis show significant improvements in the storage modulus when compared to neat PP‐g‐HMA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3242–3254, 2005     

Structure‐property relationships in exfoliated polyisoprene/clay nanocomposites

Structure‐property relationships in exfoliated polyisoprene (PI)/clay nanocomposites have been studied as a function of the clay concentration with rheometry, X‐ray diffraction, small‐angle X‐ray scattering, and transmission electron microscopy. The results presented here indicate that the interlayer spacing of layered silicates increases from 2 to at least approximately 14 nm because of the penetration of polymer molecules into the spacing between the silicate layers. The average aspect ratio (width/thickness) of the dispersed nanoplates is also estimated to be at least approximately 80. Additionally, the storage modulus of the nanocomposite exhibits frequency‐independent pseudo‐solidlike behavior above the percolation threshold [volume fraction of clay at the percolation threshold (?_p) = 0.02] and shows large enhancements (up to approximately six orders of magnitude) in comparison with the storage modulus of PI when the volume fraction of clay (?) is greater than ?_p. For the shear‐aligned PI/clay nanocomposites, an increase in the storage modulus with shear alignment is observed at ? < ?_p, whereas a decrease in the storage modulus is observed for ? > ?_p. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1000–1009, 2004     

Exfoliated poly(methyl methacrylate) and polystyrene nanocomposites occur when the clay cation contains a vinyl monomer

The bulk polymerization of methyl methacrylate and styrene in the presence of an organically modified clay containing a vinyl group that can be involved in the polymerization produces exfoliated nanocomposites. These nanocomposites have been characterized by X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, mechanical properties, and cone calorimetry. The onset temperature of thermal degradation increases with the mechanical properties. The peak heat release rate is significantly reduced for nanocomposites containing 3 or 5% clay. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1124–1135, 2003     

Synthesis and characterization of polyurethane‐urea clay nanocomposites using montmorillonite modified by oxyethylene–oxypropylene copolymer

Clay organifier with propylene oxide‐capped polyethylene glycol (PEG) with amine end group (jeffamines ED_600–2003) was synthesized through an ion exchange process between sodium cations in montmorillonite (MMT) and ? NH groups in ED_600–2003. The d‐spacing of organoclay was found to be 1.697–1.734 nm compared to 0.96 nm of pristine MMT. Transmission electron microscopy (TEM) was used to determine the molecular dispersion of the clay within ED₆₀₀. Polyurethane‐urea/montmorillonite (PUU‐MMT) nanocomposites were prepared via in situ polymerization from polyethylene glycol (PEG 400) or 1,4 butane diol (1,4 BD), toluene diisocyanate (TDI), jeffamines ED_600–2003, and 1–12 wt% of organoclay. Intercalation of PUU into modified clays was confirmed by X‐ray diffraction (XRD), scanning electron microscopy, and TEM. The barrier properties were significantly reduced; however, the thermal stability was increased in the nanocomposites as compared to the pristine polymer. Nanocomposites exhibited optical clarity and solvent resistance. The mechanical properties and the glass transition temperature of PUU were improved with the addition of organoclay. The incorporation of silicate layers gave rise to a considerable increase in the storage modulus (stiffness), demonstrating the reinforcing effect of clay on the PUU matrix. Copyright © 2009 John Wiley & Sons, Ltd.     

Solidlike transition of melt‐intercalated biodegradable polymer/clay nanocomposites

Synthetic biodegradable aliphatic polyester (BAP) intercalated into organoclay was prepared by melt compounding, and its solidlike characteristics were investigated via several rheological test modes: steady shear rotation, oscillation, and creep testing. Structural investigations with X‐ray diffraction and transmission electron spectroscopy were also performed for a better understanding of the characteristic rheological behaviors. The creep, recovery, and stress modulus exhibited a solidlike transition of BAP/clay nanocomposites that depended on the clay content. An increase in the zero shear rate viscosity and a shifting of the crossover point (storage modulus vs loss modulus) to a lower frequency were also observed with increasing clay contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2052–2061, 2003     

Polypeptide‐based nanocomposite: Structure and properties of poly(L‐lysine)/Na+‐montmorillonite

The feasibility of constructing polymer/clay nanocomposites with polypeptides as the matrix material is shown. Cationic poly‐L‐lysine · HBr (PLL) was reinforced by sodium montmorillonite clay. The PLL/clay nanocomposites were made via the solution‐intercalation film‐casting technique. X‐ray diffraction and transmission electron microscopy data indicated that montmorillonite layers intercalated with PLL chains coexist with exfoliated layers over a wide range of relative PLL/clay compositions. Differential scanning calorimetry suggests that the presence of clay suppresses crystal formation in PLL relative to the neat polypeptide and slightly decreases the PLL melting temperature. Despite lower crystallinity, dynamic mechanical analysis revealed a significant increase in the storage modulus of PLL with an increase in clay loading producing storage modulus magnitudes on par with traditional engineering thermoplastics. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2579–2586, 2002     

Effect of the premelting temperature and sample thickness on the polymorphic behavior of syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods and differential scanning calorimetry thermal analysis have been used to investigate the structural changes of syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay nanocomposites have been prepared by the mixing of sPS polymer solutions with organically modified montmorillonite. X‐ray diffraction data and differential scanning calorimetry results indicate that the dominating crystal forms and their relative fractions in sPS and sPS/clay nanocomposites are different for various premelting temperatures (T_max's). Higher T_max's favor the formation of the thermodynamically more stable β‐crystalline form, and its relative fraction has been obtained from the X‐ray diffraction data in the range of 11.5–13°. The intensity of the X‐ray diffraction data in the range of 11.5–13° decreases as the thickness of sPS/clay nanocomposites decreases from 150 to 20 μm. At the same time, the intensity of the X‐ray data in the range of 6–7° becomes sharper as the thickness of sPS/clay nanocomposites decreases. The calculation ratio based on the peak intensities at 6.2 and 6.8° for sPS/clay nanocomposites of equal thickness and crystallinity in the pure β and α forms has also been determined in this study. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1730–1738, 2003     

Plasticized polylactide/clay nanocomposites. I. The role of filler content and its surface organo‐modification on the physico‐chemical properties

Polylactide (PLA)‐layered silicate nanocomposites plasticized with 20 wt % of poly(ethylene glycol) 1000 were prepared by melt blending. Three kinds of organo‐modified montmorillonites—Cloisite® 20A, Cloisite® 25A, and Cloisite® 30B—were used as fillers at a concentration level varying from 1–10 wt %. Neat PLA and plasticized PLA with the same thermomechanical history were considered for comparison. Nanocomposites based on amorphous PLA were obtained via melt‐quenching. The influence of both plasticization and nanoparticle filling on the physicochemical properties of the nanocomposites were investigated. Characterization of the systems was achieved by size exclusion chromatography (SEC), thermogravimetric analysis (TGA), thermally modulated differential scanning calorimetry (TMDSC), X‐ray diffraction (XRD), and dynamic mechanical analysis (DMTA). SEC revealed a decrease of the molecular weight of the PLA matrix with the filler content. Thermal behavior on heating showed one cold crystallization process in the reference neat PLA sample, while two cold crystallization processes in plasticized PLA and plasticized nanocomposites. The thermal windows of these processes tend to increase with the filler content. The crystalline form of PLA developed upon heating was affected neither by the plasticization nor by the type and content of Cloisite used. It was found that the series of organo‐modified montmorillonites with decreasing affinity to PLA is Cloisite® 30B, Cloisite® 20A, and Cloisite® 25A, respectively. The dynamic mechanical properties were sensitive to the sample composition. Generally, the storage modulus increased with the filler content. Glassy PEG, well dispersed within unfilled PLA matrix, exhibited also a reinforcing effect, since the storage modulus of this sample was higher than for unplasticized reference at temperature region below the glass transition of PEG. Moreover, loss modulus of all plasticized samples revealed an additional maximum ascribed to the glass transition of PEG–rich dispersed phase, indicating partial miscibility of organic components of the systems investigated. The magnitude of this mechanical loss was correlated with the filler content, and to some extent, also with the nanofiller ability to be intercalated by polymer components. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 299–311, 2006     

Analysis of viscoelastic behavior and dynamic mechanical relaxation of copolyester based layered silicate nanocomposites using Havriliak–Negami model

The solid‐state viscoelastic properties are examined for intercalated nanocomposites based on a copolyester and (2‐ethyl‐hexyl)dimethyl hydrogenated‐tallow ammonium montmorillonite. The nanocomposites are prepared via the direct melt intercalation technique using a conventional twin‐screw extruder. Dynamic mechanical thermal analysis of the nanocomposites is conducted using two different test setups. The dynamic mechanical relaxation spectra show an increase in the storage modulus of the nanocomposite over the entire temperature range under study as compared to the pristine polymer (except in the transition region from 70 to 80 °C). These results are analyzed using the empirical Havriliak–Negami (HN) equation. The four temperature independent HN parameters (α, β, E₀, and E_∞) and one temperature dependent parameter (τ, the relaxation time) are determined by solving the HN equation for each temperature over the range of temperatures. The calculated moduli results fit well with the experimental values of the relaxation spectra for the nanocomposites. This study shows that the HN model can be applied to polymer layered silicate nanocomposites, and it can be used to predict their dynamic mechanical properties over a wide range of temperatures and frequencies a priori. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2657–2666, 2004     

Preparation of poly(propylene)/clay layered nanocomposites by melt intercalation from pristine montmorillonite (MMT)

Poly(propylene)/clay nanocomposites were prepared by melt intercalation, using pristine montmorillonite (MMT), hexadecyl trimethyl ammonium bromide (C16), poly(propylene) (PP) and maleic acid (MA) modified PP (MAPP), The nanocomposites structure is demonstrated using X‐ray diffraction (XRD) and high resolution electronic microscopy (HREM). Our purpose is to provide a general concept for manufacturing polymer nanocomposites by melt intercalation starting from the pristine MMT. We found different kneaders (twin‐screw extruder or twin‐roll mill) have influence on the morphology of the PP/clay nanocomposites. Thermogravimetric analysis (TGA) shows that the thermal stability of PP/clay nanocomposites has been improved compared with that of pure PP. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis and characterization of polycyanurate/montmorillonite nanocomposites

The advantages of cyanate esters (CEs) versus competitor systems such as epoxies and polyimides, as well as the great reinforcing potential of organoclays properly dispersed into a polymeric matrix, have been examined in a series of polycyanurate (PCN)/montmorillonite (MMT) nanocomposites prepared under appropriate polymerization conditions. The curing schedule applied resulted in gradual propagation of polymerization. Through this procedure, the intragallery curing rate becomes comparable to the extragallery one, allowing intercalation before gelation. Systems with clay loadings from 1 to 3% per weight were synthesized, and their morphology and mechanical properties were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), wide angle X‐ray scattering (WAXS), dynamic mechanical analysis (DMA), and tensile tests. Microscopy investigations revealed better dispersion for the 3 wt % system compared to smaller concentrations, in which aggregation and, in some cases, agglomeration were the conspicuous features. Roughness and area analyses revealed more homogeneous dispersion for this nanocomposite. Topology and 3D‐phase images further suggested considerable reduction of the average particle diameters. WAXS analysis showed that the interlayer spacing of nanocomposites was increased compared to pristine MMT, indicating the formation of intercalated structures. On the other hand, tensile strength and elongation at break values displayed abrupt diminution with MMT addition, while Young's modulus exhibited a slight but systematic increment with MMT content. The decreasing glass transition tendency observed for small clay loadings was reversed in the case of 3 wt %, while secondary transitions were practically unaffected by the presence of MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1036–1049, 2008     

Numerical simulation of the tensile modulus of nanoclay-filled polymer composites

A numerical simulation model that incorporates three phases, polymer matrix, interlayer, and clay platelet, was developed to predict the tensile modulus of nanoclay-filled polymer composites. The interlayer was introduced to account for the fact that the mechanical properties of the polymer near the clay surface are different from those of the polymer matrix. The effects of the properties of interlayers, the structure of clay clusters, and platelet distributions upon the modulus of elasticity of the nanocomposites, were studied. The simulation results show that a decrease in the interlayer modulus, as well as an increase in the interlayer thickness, would decrease the modulus of the nanocomposites. Furthermore, it was found that the maximum strain, located in the interlayer near the end of the clay platelet, increases significantly with decreasing interlayer modulus. The effects of the distribution of clay platelets upon composite modulus were interpreted in terms of two parameters, platelet overlap length, and the lateral distance between platelets. Comparison of simulation results with experimental data from the literature has confirmed the reliability of the numerical simulation method used in the present study. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2391–2406, 2004     

Poly(cyclohexene oxide)/clay nanocomposites by photoinitiated cationic polymerization via activated monomer mechanism

Poly(cyclohexene oxide) (PCHO)/clay nanocomposites were prepared by in situ photoinitiated activated monomer cationic polymerization. The polymerization of cyclohexene oxide through the interlayer galleries of the clay can provide distribution of the clay layers in the polymer matrix homogenously and results in the formation of PCHO/clay nanocomposites. The exfoliated structures were characterized by X‐ray diffraction spectroscopy, thermogravimetric analysis, transmission electron microscopy, and atomic force microscopy. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5328–5335, 2009