Functionalized graphene sheet—Poly(vinylidene fluoride) conductive nanocomposites

PVDF nanocomposites based on functionalized graphene sheets, FGS prepared from graphite oxide, and exfoliated graphite, EG, were prepared by solution processing and compression molding. FGS remains well dispersed in the PVDF composites as evidenced by the lack of the characteristic graphite reflection in the composites. Although the α‐phase of PVDF is seen in the EG‐based composites, a mixture of α‐ and β‐phases is present in the FGS analogs. SEM and TEM imaging show smooth fractured surfaces with oriented platelets of graphite stacks and obvious debonding from the matrix in the EG‐PVDF composites. In contrast, the FGS‐PVDF composites show a wrinkled topography of relatively thin graphene sheets bonded well to the matrix. Storage modulus of the composites was increased with FGS and EG concentration. A lower percolation threshold (2 wt %) was obtained for FGS‐PVDF composites compared to EG‐PVDF composites (above 5 wt %). Lastly, the FGS‐PVDF composites show an unusual resistance/temperature behavior. The resistance decreases with temperature, indicating an NTC behavior, whereas EG‐PVDF composites show a PTC behavior (e.g., the resistance increases with temperature). We attribute the NTC behavior of the FGS based composites to the higher aspect ratio of FGS which leads to contact resistance predominating over tunneling resistance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 888–897, 2009     

Dynamic mechanical and dielectrical properties of poly(vinyl alcohol) and poly(vinyl alcohol)‐based nanocomposites

In this article we report on the investigation of the dynamics of poly(vinyl alcohol) (PVA) and PVA‐based composite films by means of dielectric spectroscopy and dynamic mechanical thermal analysis. Once the characterization of pure PVA was done, we studied the effect of a nanostructured magnetic filler (nanosized CoFe₂O₄ particles homogeneously dispersed within a sulfonated polystyrene matrix) on the dynamics of PVA. Our results suggest that the α‐relaxation process, corresponding to the glass transition of PVA, is affected by the filler. The glass‐transition temperature of PVA increases with filler content up to compositions of around 10 wt %, probably as a result of polymer–filler interactions that reduce the polymer chain mobility. For filler contents higher than 10 wt %, the glass‐transition temperature of PVA decreases as a result of the absorption of water that causes a plasticizing effect. The β‐ and γ‐relaxation processes of PVA are not affected by the filler as stated from both dynamic mechanical thermal analysis and dielectric spectroscopy. Nevertheless, both relaxation processes are greatly affected by the moisture content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1968–1975, 2001     

Polymorphism behavior of poly(ethylene naphthalate)/clay nanocomposites

Thermally stable organically modified clays based on 1,3‐didecyl‐2‐methylimidazolium (IM2C10) and 1‐hexadecyl‐2,3‐dimethyl‐imidazolium (IMC16) were used to prepare poly(ethylene naphthalate) (PEN)/clay nanocomposites via a melt intercalation process. The clay dispersion in the resulting hybrids was studied by a combination of X‐ray diffraction, polarizing optical microscopy, and transmission electron microscopy. It was found that IMC16 provided better compatibility between the PEN matrix and the clay than IM2C10, as evidenced by some intercalation of polymer achieved in the PEN/IMC16‐MMT hybrid. The effects of clay on the crystal structure of PEN were investigated. It was found that both pristine MMT and imidazolium‐treated MMT enhanced the formation of the β‐crystal phase under melt crystallization at 200 °C. At 180 °C, however, the imidazolium‐treated MMT was found to favor the α‐crystal form instead. The difference in clay‐induced polymorphism behavior was attributed to conformational changes experienced by the clay modifiers as the crystallization temperature changes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1040–1049, 2006     

Intercalated poly(vinylidene fluoride)/clay nanocomposites: Structure and properties

The preparation and characterization of melt‐intercalated poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported. Organophilic clay (clay treated with dimethyl dihydrogenated tallow quaternary ammonium chloride) was used for the nanocomposite preparation. The composites were characterized with X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). XRD results indicated the intercalation of the polymer in the interlayer spacing. The incorporation of clay in PVDF resulted in the β form of PVDF. DSC nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity. Isothermal crystallization studies show an enhanced rate of crystallization with the addition of clay. DMA indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 31–38, 2003     

Organic–inorganic polymeric nanocomposites involving novel titanium tetraisopropylate in polyethylene–octene elastomer

The new nanocomposites, by means of an in situ sol–gel process consisting of metallocene polyethylene–octene elastomer (POE) and titanium tetraisopropylate (TTIP), were investigated. In addition, the acrylic acid grafted POE (POE‐g‐AA) was studied as an alternative to POE. Fourier transform infrared (FTIR) spectroscopy, a dynamic mechanical analyzer (DMA) spectrometer, an X‐ray diffractometer (XRD), differential scanning calorimetry (DSC), a thermogravimetric analyzer (TGA), an Instron mechanical tester, and a scanning electron microscope (SEM) were used to characterize and examine the samples. The results indicate that the POE‐g‐AA/TiO₂ hybrid could have a positive effect on the properties of the POE/TiO₂ hybrid because the carboxylic acid groups of acrylic acid should act as coordination sites for the titania phase to form a Ti? O? C chemical bond. The strength of interfacial bonding between the polymer chains and the ceramic phase depended on the amount of TiO₂, as shown by the change in glass‐transition temperature (T_g) with TiO₂ content. The result of mechanical and thermal tests showed that both the tensile strength and the T_g increased to a maximum value and then decreased with an increasing of TiO₂ because excess particles (e.g., greater than 10 wt % TiO₂) might cause separation or segregation between the organic and inorganic phases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4272–4280, 2004     

States of water in poly(vinyl alcohol) derivative hydrogels

We studied the behavior of absorbed water in equilibrium‐swollen poly(vinyl alcohol) derivative hydrogels by differential scanning calorimetry (DSC), ¹H nuclear magnetic resonance, and wide‐angle X‐ray diffraction. By DSC, three types of water were detected, and their relative fractions were estimated. With this technique we also calculated the pore size for every sample. From the nonexponential decay of the spin–spin relaxation data, we distinguished two environmental states of the absorbed water in the samples. The relaxation times were determined. From these data, we calculated the fractions of each type of water for every hydrogel and related them to the degree of crosslinking. The X‐ray study indicated that the water absorbed in these hydrogels forms a single crystalline phase on cooling. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1462–1467, 2003     

Hydrogen‐bonding,crystallinity, and morphological properties of poly(silicic acid)/waterborne polyurethane nanocomposites

Unique nanocomposites consisting of poly(silicic acid) nanoparticles (PNs) and waterborne polyurethane (WPU) were prepared. The aliphatic WPU prepared in this study was end‐capped with a silanol group, which could react with PNs via a sol–gel process. PNs were modified with phenyltrimethoxysilane (PTMS) and 3‐(trimethoxysilyl)propyl ester (TMPE) and then blended with WPU. The structure–property relationships were examined. Solid‐state ²⁹Si NMR spectra of WPU showed that structures T₁, T₂, and T₃ of WPU decreased and structures Q₃ and Q₄ of PN/WPU nanocomposites increased gradually. When the PN concentration increased to 10 wt %, PN/WPU nanocomposites exhibited the maximum fraction of hydrogen‐bonded carbonyl groups. In the PTMS–PN and TMPE–PN systems, the fraction of hydrogen‐bonded carbonyl groups fluctuated stably when the concentrations of PTMS–PN and TMPS–PN exceeded 5 wt %. The X‐ray diffraction results revealed that α‐form, γ‐form, or triclinic crystallization could be found in the WPU matrix. A differential scanning calorimetry spectrum showed that the crystalline structure of the hard segment of WPU was influenced by the nanoparticle concentration. The degrees of crystallinity were 88% for the PN/WPU nanocomposites, 41% for the PTMS–PN/WPU nanocomposites, and 54% for the TMPE–PN/WPU nanocomposites when the PN, PTMS–PN, and TMPE–PN concentrations were 5 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1076–1089, 2005     

Structure and properties of polyamide‐6/vermiculite nanocomposites prepared by direct melt compounding

Polyamide‐6 (PA6)/vermiculite nanocomposites were fabricated through the direct melt compounding of maleic anhydride‐modified vermiculite (MAV) with PA6 in a twin‐screw extruder followed by injection molding. The structure and morphology of the nanocomposites were determined by X‐ray diffraction and scanning and transmission electron microscopy techniques. The results revealed the formation of intercalated and exfoliated vermiculite platelets in the PA6 matrix. Tensile measurement showed that the tensile modulus and strength of the nanocomposites tended to increase with increasing vermiculite content. The thermal properties of the nanocomposites were determined by dynamic mechanical analysis, differential scanning calorimetry, and thermogravimetry measurements. The storage modulus of the PA6–MAV nanocomposites increased to almost twice that of the neat PA6. The thermal stability of the nanocomposites increased dramatically, and this was associated with the addition of vermiculite. The effect of the addition of maleic anhydride on the formation of the PA6–vermiculite nanocomposites was examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2860–2870, 2002     

Preparation and fluorescent properties of poly(vinyl alcohol) bearing coumarin

A novel water‐soluble fluorescent material was prepared via ring‐opening reaction between 4‐methyl‐7‐(2,3‐expoxypropoxy) coumarin (MEC) and poly(vinyl alcohol) (PVA). The fluorescent behaviors of this material (PVA–MEC) in solution, solid and film were studied in detail. The results showed that the fluorescence of PVA–MEC arose from isolated dye molecules and had a good film forming ability. In addition, the effects of acid/base environments on PVA–MEC were studied and the results showed that it was less affected by environment than 7‐HMC. Moreover, relative fluorescence intensity of PVA–MEC had an excellent linear response in the temperature range of 0–60°C. These observations suggest that PVA–MEC is an excellent fluorescent macromolecular material with a convenient method of preparation and had a good water‐soluble ability. Copyright © 2007 John Wiley & Sons, Ltd.     

Dispersion and distribution of organically modified montmorillonite in nylon‐66 matrix

Nylon‐66 nanocomposites were prepared by melt‐compounding nylon‐66 with an alkyl ammonium surfactant pretreated montmorillonite (MMT). The thermal stability of the organic MMT powders was measured by thermogravimetric analysis. The decomposition of the surfactant on the MMT occurred from 200 to 500 °C. The low onset decomposition temperature of the organic MMT is one shortcoming when it is used to prepare polymer nanocomposites at high melt‐compounding temperatures. To provide greater property enhancement and better thermal stability of the polymer/MMT nanocomposites, it is necessary to develop MMT modified with more thermally stable surfactants. The dispersion and spatial distribution of the organic MMT layers in the nylon‐66 matrix were characterized by X‐ray diffraction. The organic MMT layers were exfoliated but not randomly dispersed in the nylon‐66 matrix. A model was proposed to describe the spatial distribution of the organic MMT layers in an injection‐molded rectangular bar of nylon‐66/organic MMT nanocomposites. Most organic MMT layers were oriented in the injection‐molding direction. Layers near the four surfaces of the bar were parallel to their corresponding surfaces; whereas those in the bulk differed from the near‐surface layers and rotated themselves about the injection‐molding direction. The influence of the spatial distribution of the organic MMT on crystallization of nylon‐66 was also investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1234–1243, 2003     

Physical and electronic properties in multiwalled carbon nanotube–poly(3‐dodecylthiophene) nanocomposites

The properties of nanocomposites of dodecyl ester functionalized multiwalled carbon nanotube (FMWNT) and four poly(3‐dodecyl thiophene) (P3DDT) samples with different molecular weight and chain regioregularity are reported here. Uniform dispersion of FMWNT in the composites is evident from TEM study. π–π and CH–π interactions are evident from FTIR spectra in the low molecular weight (M_w = 8 × 10⁴) and high regiorandom (head‐tail = 69 mol %) P3DDT (ILM) composites; however, such interactions are not so prominent for other P3DDTs. Wide‐angle X‐ray scattering patterns indicate intact interchain lamellar structure of P3DDT in the composites. DSC study shows decrease of main chain melting peak of P3DDT (ILM) with increasing F‐MWNT content but the decrease is lower with higher molecular weight and higher regioregular samples. Dynamic mechanical analyzer study indicates that there is no significant change in the T_g, T_β, and T_γ transition temperature with FMWNT concentration indicating almost ideal mixing of the components. The percent increase of G′ increases with increasing FMWNT loading and also with temperature showing an 84% increase in storage modulus at –20 °C for ILM12 samples. The UV–vis spectrum indicates a decrease in band gap with FMWNT concentration for ILM composites, however, it is negligible with other P3DDTs. Photoluminescence quenching and multiple emission peaks occur in the composites. dc‐Conductivity of the composites increases by two orders and current‐voltage (I–V) curves show memory effect only in ILM‐MWNT composites. The I–V curves of other P3DDT nanocomposites exhibit rectification property. Quantitative explanation of electronic properties has been afforded from the band energy and work function values. So, the electronic properties of the nanocomposite can be tuned by changing the molecular weight, regioregularity, and concentration of FMWNT. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1412–1425, 2009     

Fabrication of poly(vinyl alcohol)‐graphene quantum dots coated with poly(3,4‐ethylenedioxythiophene) for supercapacitor

Conducting nanofiber composed of poly(vinyl alcohol) (PVA), graphene quantum dots (GQDs) and poly(3,4‐ethylenedioxythiophene) (PEDOT) was prepared for symmetrical supercapacitor through electrospinning and electropolymerization techniques. The formation of PVA nanofibers with the addition of GQDs was excellently prepared with the average diameter of 55.66 ± 27 nm. Field emission scanning electron microscopy images revealed that cauliflower‐like structure of PEDOT was successfully coated on PVA‐GQD electrospun nanofibers. PVA‐GQD/PEDOT nanocomposite exhibited the highest specific capacitance of 291.86 F/g compared with PVA/PEDOT (220.73 F/g) and PEDOT (161.48 F/g). PVA‐GQD/PEDOT also demonstrated a high specific energy and specific power of 16.95 and 984.48 W/kg, respectively, at 2.0 A/g current density. PVA‐GQD/PEDOT exhibited the lowest resistance of charge transfer (R_ct) and equivalent series resistance compared with PEDOT and PVA/PEDOT, indicating that the fast ion diffusion between the electrode and electrolyte interface. PVA‐GQD/PEDOT nanocomposite also showed an excellent stability with retention of 98% after 1000 cycles. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 50–58     

Viscoelastic properties of silica‐grafted poly(styrene–acrylonitrile) nanocomposites

The melt state viscoelastic properties of styrene–acrylonitrile random copolymers grafted to silica nanoparticles and prepared by in situ atom transfer radical polymerization are examined. Linear dynamic oscillatory viscoelastic measurements indicate that nanocomposites with silica contents as low as 1.2 vol % exhibit solid‐like response. Steady shear results in considerable alteration to the mesoscale structure and results in the failure of the Cox‐Merz rule. Flow reversal studies confirm the elastic nature of the mesoscale structure and demonstrate that the relaxation of the flow altered structure is slow, non‐Brownian, and possibly cooperative. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2014–2023, 2006     

Nonisothermal crystallization behavior and crystalline structure of poly(3‐hydroxybutyrate)/layered double hydroxide nanocomposites

X‐ray diffraction method and differential scanning calorimetry analysis have been used to investigate the nonisothermal crystallization of poly(3‐hydroxybutyrate) (PHB)/poly(ethylene glycol) phosphonates (PEOPAs)‐modified layered double hydroxide (PMLDH) nanocomposites. Effects of cooling rates and PMLDH contents on the nonisothermal crystallization behavior of PHB were explored. These results show that the addition of 2 wt % PMLDH into PHB caused heterogeneous nucleation increasing the crystallization rate and reducing the activation energy. By adding PMLDH into the PHB probably hinder the transport ability of the molecule chains and result in a decreasing crystallity of PHB, thus increasing the activation energy. The correlation among melting behavior, apparent crystallite size, and paracrystalline distortion of PHB/PMLDH nanocomposites has been also discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 995–1002, 2007     

Amine‐cured epoxy/clay nanocomposites. I. Processing and chemical characterization

The processing of nanocomposite materials composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay is reported. A novel sample preparation scheme was used to process the modified clay in the glassy epoxy network, resulting in nanocomposites where the clay was both exfoliated and intercalated by the epoxy network. The processing scheme involves sonication of the constituent materials in a solvent, followed by solvent extraction to generate a composite with homogeneous dispersions of the nanoclay. Fourier transform infrared spectroscopy (FTIR) and Fourier transform (FT‐)Raman spectroscopy confirmed that the chemical structure of the epoxy network was not affected by the use of solvents in this processing scheme. The glass‐transition temperature, T_g, linearly increased with an increased weight ratio of the nanoclay. The microstructure of clay nanoplatelets in the composites was observed with transmission electron microscopy (TEM), wide‐angle X‐ray scattering (WAXS), and small‐angle X‐ray scattering (SAXS). It was found that the clay nanoplatelets were well‐dispersed, and were intercalated as well as exfoliated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4384–4390, 2004     

New Millable Polyurethane/Organoclay Nanocomposite: Preparation,Characterization and Properties

The preparation, characterization and properties of novel millable polyurethane/organoclay nanocomposites are reported. Clay treated with methyl tallow bis(2‐hydroxyethyl) quaternary ammonium chloride was used as an organoclay for nanocomposite preparation. X‐ray diffraction indicated the intercalation of polymer chains inside the interlayer spacings of the clay. Dynamic mechanical analysis showed a significant increase in storage modulus, and tensile strength increases with increased organoclay loading.

X‐ray diffraction patterns of millable polyurethane/organoclay nanocomposites.     

Structure and mechanical properties in drawn poly(l‐lactide)/clay hybrid films

Films composed of poly(l ‐lactide) (PLLA)/organophilic montmorillonite hybrids (PLACHs) have been prepared via a melt‐compounding process, which is followed by uniaxial drawing at 90°C in air. In addition, an enhancement of the mechanical properties of these drawn PLACH films, which is expected to differ depending on the drawn ratios, is also estimated by dynamic viscoelastic measurements. Three different organoclay concentrations in the hybrid of 3, 5, and 9 wt% were investigated. The structural parameters for the PLLA crystallites in the drawn films, such as the c‐axis orientation function (f_PLLA) and crystallite size, were measured by X‐ray diffraction, and their drawn ratio (λ) and clay concentration dependence were examined from a textural viewpoint. Another orientation function (f_clay) of the organoclay particles was obtained by transmission electron microscopy (TEM). The values of f_PLLA and crystallinity for PLLA sharply increased with λ for λ < 3, although f_clay was unchanged during the initial stage of elongation. In the high‐λ region (>5), the organoclay particles in the PLACHs started orienting themselves parallel to the draw direction. Copyright © 2008 John Wiley & Sons, Ltd.     

Phase behavior of modified montmorillonite– poly(ϵ‐caprolactone) nanocomposites

The thermal behavior and overall isothermal crystallization kinetics of a series of organophilic modified montmorillonite–poly(?‐caprolactone) nanocomposites were investigated. In general, the thermal behavior was influenced more by the type of dispersion than by the clay content. For nanocomposites in which silicate platelets were predominantly dispersed in the polymer matrix to give exfoliated structures, the thermal properties were improved with respect to those of neat poly(?‐caprolactone), whereas in those cases in which simply intercalated structures were attained, the thermal properties regularly decayed as the clay content increased. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1321–1332, 2004     

Formation and dichroism of poly(vinyl alcohol)–iodine complex in photocurable film

The formation of polyiodine complexes was investigated in a photocurable poly(vinyl alcohol) modified N‐methyl‐4(4′‐formylstyryl)pyridinium methosulfate acetal (PVA‐SbQ), which is a photofunctional group that causes photodimerization. PVA‐SbQ films with polyiodine complexes were prepared to be photocured, iodinated and soaked in a boric acid solution. The formation of PVA–polyiodine complexes was studied during iodinating and while in the boric acid treatment through UV–vis absorption spectrometry, resonance Raman spectrometry and IR absorption spectrometry. As a result, polyiodines were formed in the photocurable PVA‐SbQ films, and the formation of PVA–polyiodine complexes was enhanced by boric acid treatment. It was found that the SbQ‐ratio of PVA‐SbQ affects the formation of PVA–polyiodine complexes. The photocrosslinking by the dimerization of SbQ groups helps to form the PVA–I₅⁻ complex during the boric acid treatment. Based on this effect, we demonstrated a unique recording method by the PVA–polyiodine complex formation. The PVA‐SbQ film cured by the irradiation of the liner polarized light showed that dichroism of the PVA–polyiodine complexes formed after iodination. Copyright © 2015 John Wiley & Sons, Ltd.