Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Ultrafine fibrous cellulose membranes from electrospinning of cellulose acetate

Three solvents, that is, acetone, acetic acid, and dimethylacetamide (DMAc), with a range of solubility parameter δ, surface tension γ, viscosity η and boiling temperature were used to generate mixtures for electrospinning cellulose acetate (CA) (degree of substitution, DS = 2.45). Although none of these solvents alone enables continuous formation of fibers, mixing DMAc with either acetone or acetic acid produced suitable solvent systems. The 2:1 acetone:DMAc mixture is the most versatile mixture because it allows CA in the 12.5–20% concentration range to be continuously electrospun into fibrous membranes. These CA solutions have η between 1.2 and 10.2 poise and γ around 26 dyne/cm and produce smooth fibers with diameters from 100 nm to ～1 μm. Fiber sizes generally decrease with decreasing CA concentrations. The nature of the collectors affects the morphology as well as packing of fibers. Fibers collected on paper have more uniform sizes, smooth surfaces, and fewer defects, whereas fibers collected on water are more varied in size. Electrically conductive solid collectors, such as Al foil and water, favor more tightly packed and less porous membranes. Porous collectors, like paper and copper mesh, produce highly porous membranes. The pores in membranes collected on the Al foil and paper are much better interconnected in the planar directions than those in membranes collected on water. There is evidence that electrospinning induces order in the fibers. Deacetylation of CA membranes is more efficient and complete in NaOH/ethanol than in aqueous NaOH, producing DS values between 0.15 and 2.33 without altering fiber surfaces, packing, or organization. The fully regenerated cellulose membranes are similarly hydrophilic as commodity cellulose fibrous matrices but absorb nearly 10 times as much water. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2119–2129, 2002     

Effective grafting of polymers onto ultrafine silica surface: Photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface and Mn2(CO)10

The effective grafting of vinyl polymers onto an ultrafine silica surface was successfully achieved by the photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface with Mn₂(CO)₁₀ under UV irradiation at 25 °C. The introduction of trichloroacetyl groups onto the surface of silica was achieved by the reaction of trichloroacetyl isocyanate with surface amino groups, which were introduced by the treatment of silica with 3‐aminopropyltriethoxysilane. During the polymerization, the corresponding polymers were effectively grafted onto the surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mn₂(CO)₁₀. The percentage of poly(methyl methacrylate) grafting onto the silica reached 714.6% after 90 min. The grafting efficiency (proportion of grafted polymer to total polymer formed) in the polymerization of methyl methacrylate was very high, about 80%, indicating the depression of formation of ungrafted polymer. Polymer‐grafted silica gave a stable colloidal dispersion in good solvents for grafted polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2157–2163, 2001     

电纺聚乙烯醇超细纤维膜的性能研究

由电纺制备聚乙烯醇(PVA)超细纤维膜,以扫描电镜观察纤维的微观形貌,用X射线衍射研究超细纤维膜的结晶行为,并测定了PVA超细纤维膜的力学性能和吸水性.结果表明,PVA超细纤维的平均直径为(184±26)nm,超细纤维中PVA的结晶度和晶体有序程度较浇铸膜低.超细纤维膜的拉伸强度、模量和断裂伸长率均较浇铸膜差,吸水率在300%以上,高于浇铸膜.     

Thermal properties and structure of electrospun blends of PVDF with a fluorinated copolymer

We report the structure and thermal properties of blends comprising poly(vinylidene fluoride) (PVDF) and a random fluorinated copolymer (FCP) of poly(methyl methacrylate)‐random‐1H,1H,2H,2H‐perfluorodecyl methacrylate, promising membrane materials for oil–water separation. The roles of processing method and copolymer content on structure and properties were studied for fibrous membranes and films with varying compositions. Bead‐free, nonwoven fibrous membranes were obtained by electrospinning. Fiber diameters ranged from 0.4 to 1.9 μm, and thinner fibers were obtained for PVDF content >80%. As copolymer content increased, degree of crystallinity and onset of degradation for each blend decreased. Processing conditions have a greater impact on the crystallographic phase of PVDF than copolymer content. Fibers have polar beta phase; solution‐cast films contain gamma and beta phase; and melt crystallized films form alpha phase. Kwei's model was used to model the glass transition temperatures of the blends. Addition of FCP increases hydrophobicity of the electrospun membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 312–322     

Electrospinning of ultrafine PVDF/PC fibers from their dispersed solutions

Dispersed solutions of poly(vinylidene fluoride) (PVDF)/polycarbonate (PC) in the mixed solvent of N,N‐dimethylformamide (DMF)/tetrahydrofuran (THF) were used to electrospin in order to discuss the relationship between the properties of the polymer dispersions and the morphology of the obtained ultrafine fibers. With the changes of the mass ratio of PVDF/PC, the relative molecular mass of PVDF, and the volume ratio of DMF/THF, the morphology and the microstructure of the prepared PVDF/PC ultrafine fibers altered in accord with the viscosity, surface tension, and conductivity of the PVDF/PC dispersions. When the PVDF/PC mass ratio varied from 9/1 to 5/5, the ability of the polymer chain entanglement in PVDF/PC dispersion decreased as to the lower relative molecular mass of PC and higher chain rigidity, which lead to the formation of the beaded fibers together with the distinct core/shell structure. Similar phenomenon was also found when the lower molecular mass of PVDF was used instead of a higher one. Though the change of DMF/THF volume ratio did not specifically contribute to the properties of PVDF/PC dispersions, the accelerated evaporation and solubility of the mixed solvent by the THF amount increasing was feasible to generate the uniform fibrous morphology and the distinct core/shell structure. © 2009 Wiley Periodicals, Inc.J Polym Sci Part B: Polym Phys 48: 372–380, 2010     

Microwave‐assisted derivatization of cellulose in an ionic liquid: An efficient,expedient synthesis of simple and mixed carboxylic esters

Microwave (MW)‐assisted cellulose dissolution in ionic liquids (ILs) has routinely led either to incomplete biopolymer solubilization, or its degradation. We show that these problems can be avoided by use of low‐energy MW heating, coupled with efficient stirring. Dissolution of microcrystalline cellulose in the IL 1‐allyl‐3‐methylimidazolium chloride has been achieved without changing its degree of polymerization; regenerated cellulose showed pronounced changes in its index of crystallinity, surface area, and morphology. MW‐assisted functionalization of MCC by ethanoic, propanoic, butanoic, pentanoic, and hexanoic anhydrides has been studied. Compared with conventional heating, MW irradiation has resulted in considerable decrease in dissolution and reaction times. The value of the degree of substitution (DS) was found to be DS_ethanoate > DS_propanoate > DS_butanoate. The values of DS_pentanoate and DS_hexanoate were found to be slightly higher than DS_ethanoate. This surprising dependence on the chain length of the acylating agent has been reported before, but not rationalized. On the basis of the rate constants and activation parameters of the hydrolysis of ethanoic, butanoic, and hexanoic anhydrides in aqueous acetonitrile (a model acyl transfer reaction), we suggest that this result may be attributed to the balance between two opposing effects, namely, steric crowding and (cooperative) hydrophobic interactions between the anhydride and the cellulosic surface, whose lipophilicity has increased, due to its partial acylation. Four ethanoate‐based mixed esters were synthesized by the reaction with a mixture of the two anhydrides; the ethanoate moiety predominated in all products. The DS is reproducible and the IL is easily recycled. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 48: 134–143, 2010     

Diameter control of electrospun chitosan‐collagen fibers

In this article, the effects of fundamental parameters including applied voltage, feed rate of solution, collecting distance of fibers, the ratio of chitosan to collagen in the fibers and polymer solution concentration on the diameter and morphology of electrospun collagen‐chitosan complex nanofibers were studied to produce ultrafine polymer fibers. Based on the systematic parametric study, it is possible to control the diameter and morphology of the electrospun polymer fibers. This will also be helpful for electrospinning of various polymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1949–1955, 2009     

Temperature‐dependent phase‐segregation behavior and antifouling performance of UV‐curable methacrylated PDMS/PEG coatings

Controllable phase segregation adjustment for immiscible polymer blends has always been tough, which hinders the development of amphiphilic antifouling coatings from more accessible blends. Herein, methacrylated poly(dimethylsiloxane) (PDMS‐MA) was synthesized and mixed with poly(ethylene glycol)methylether methacrylate (PEG‐MA). It was interestingly discovered that these PDMS‐MA/PEG‐MA blends displayed upper critical solution temperatures (UCST) due to thermo‐induced conformational change of PEG‐MA and the UCST changed with PDMS‐MA/PEG‐MA mass ratios. Micro‐/nano‐phase segregation, nanophase segregation, or homogenous morphology were therefore achieved. These PDMS‐MA/PEG‐MA blends with different mass ratios were UV‐cured under varying temperatures to fabricate coatings. Their surface morphology and wettability are readily adjusted by phase segregation. For the first time, highly hydrophilic surface was achieved for coatings with microphase segregation because of the exposure of PEG‐rich domains, which exhibited an enhanced protein resistance against bovine serum albumin (BSA). Anti‐bacterial performance (Shewanella loihica) was also observed for these PDMS/PEG coatings. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1612–1623     

Cross‐linked poly(aryl ether sulfone) membranes for direct methanol fuel cell applications

Partially sulfonated poly(aryl ether sulfone) (PESS) was synthesized and methacrylated via reaction with glycidyl methacrylate (PESSGMA) and cross‐linked via radical polymerization with styrene and vinyl‐phosphonic acid (VPA). The chemical structures of the synthesized pre‐polymers were characterized via FTIR and ¹H NMR spectroscopic methods and molecular weight was determined via GPC. Membranes of these polymers were prepared via solution casting method. The crosslinking of the PESS polymer reduced IEC, proton conductivity, swelling in water, and methanol permeability of the membranes while increasing the modulus and the glass transition temperature. However, the introduction of the VPA comonomer increased the proton conductivity while maintaining excellent resistance to methanol cross‐over, which was significantly higher as compared with both PESS and the commercial Nafion membranes. Membranes of PESSGMA copolymers incorporating VPA, exhibited proton conductivity values at 60 °C in the range of 16–32 mS cm⁻¹ and methanol permeability values in the range of 6.52 × 10⁻⁹ – 1.92 × 10⁻⁸ cm² s⁻¹. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 558–575     

Ultrafine hydrogel fibers with dual temperature‐ and pH‐responsive swelling behaviors

Ultrafine hydrogel fibers that were responsive to both temperature and pH signals were prepared through the electrospinning of poly(N‐isopropylacrylamide) (PNIPAAm) and poly(acrylic acid) mixtures in dimethylformamide. Both the diameters (700 nm to 1.2 μm) and packing of the fibers could be controlled through changes in the polymer compositions and PNIPAAm molecular weights. These fibers were rendered water‐insoluble by the addition of either Na₂HPO₄ or poly(vinyl alcohol) (PVA) to the solution, followed by the heat curing of the fibers. The fibers crosslinked with Na₂HPO₄ swelled to 30–120 times in water; this was significantly higher than the swelling of those crosslinked with PVA. The PVA‐crosslinked hydrogel fibers, however, exhibited faster swelling kinetics; that is, they reached equilibrium swelling in less than 5 min at 25 °C. They were also more stable after 1 week of water exposure; that is, they lost less mass and retained their fibrous form better. All the hydrogel fibers showed a drastic increase in the swelling between pH 4 and 5. The PVA‐crosslinked hydrogel fibers exhibited distinct temperature‐responsive phase‐transition behavior of PNIPAAm, whereas the Na₂HPO₄‐crosslinked hydrogel fibers showed altered two‐stage phase transitions that reflected side‐chain modification of PNIPAAm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6331–6339, 2004     

Preparation of submicron‐scale,electrospun cellulose fibers via direct dissolution

Cellulose nonwoven mats of submicron‐sized fibers (150 nm–500 nm in diameter) were obtained by electrospinning cellulose solutions. A solvent system based on lithium chloride (LiCl) and N,N‐dimethylacetamide (DMAc) was used, and the effects of (i) temperature of the collector, (ii) type of collector (aluminum mesh and cellulose filter media), and (iii) postspinning treatment, such as coagulation with water, on the morphology of electrospun fibers were investigated. The scanning electron microscopy (SEM) and X‐ray diffraction studies of as‐spun fibers at room temperature reveal that the morphology of cellulose fibers evolves with time due to moisture absorption and swelling caused by the residual salt and solvent. Although heating the collector greatly enhances the stability of the fiber morphology, the removal of salt by coagulation and DMAc by heating the collector was necessary for the fabrication of dry and stable cellulose fibers with limited moisture absorption and swelling. The presence and removal of the salt before and after coagulation have been identified by electron microprobe and X‐ray diffraction studies. When cellulose filter media is used as a collector, dry and stable fibers were obtained without the coagulation step, and the resulting electrospun fibers exhibit good adhesion to the filter media. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1673–1683, 2005     

Synthesis and miscibility studies of [60]fullerenated poly(2‐hydroxyethyl methacrylate)

[60]Fullerenated poly(2‐hydroxyethyl methacrylate)s containing 0.6–3.0 wt % C₆₀ were synthesized. These polymers are soluble in methanol and N,N‐dimethylformamide (DMF). [60]Fullerenated poly(2‐hydroxyethyl methacrylate)s with higher C₆₀ contents are only sparingly soluble in DMF and virtually insoluble in other organic solvents. A loading of 1.2 wt % C₆₀ in poly(2‐hydroxyethyl methacrylate) does not greatly affect its miscibility with poly(N‐vinyl‐2‐pyrrolidone), poly(1‐vinylimidazole), and poly(4‐vinylpyridine). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1157–1166, 2002     

Hydrobromination of residual vinyl groups on divinylbenzene polymer particles followed by atom transfer radical surface graft polymerization

Rigid and monodisperse spherical polymer particles with 2.36 ± 0.18 μm diameter containing residual surface vinyl groups were prepared by photoinitiated precipitation polymerization of divinylbenzene. Anti‐Markovnikov addition of HBr to the surface vinyl groups yielded a 2‐bromoethyl functionality that was used as macroinitiator for atom transfer radical polymerization (ATRP), providing the possibility for further functionalization by controlled “grafting from” processes. This was demonstrated by grafting of glycidyl methacrylate brushes from the particle surface, using an ATRP system based on CuBr and pentamethyl diethylenetriamine. Existence of a methacrylic overlayer was verified by FTIR and XPS measurements, and the grafted particles were easily dispersed in water, confirming conversion of the particle surface from hydrophobic to hydrophilic. Hydrobromination of residual vinyl groups yields a macroinitiator that can be used for grafting of glycidyl methacrylate by ATRP. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1259–1265, 2009     

Novel cellulose derivatives. V. Synthesis and thermal properties of esters with trifluoroethoxy acetic acid

Esters of cellulose with trifluoroethoxy acetic acid (TFAA) were prepared in homogeneous phase using a mixed anhydride with p‐toluenesulfonic acid. Esters with low degree of substitution (DS), and with DS rising from 0 to 3, had hydrophobic character that prevented the usual association with moisture, which is otherwise typical of cellulose esters with low DS. Cellulose trifluoroethoxy acetate (CT) had T_g's declining by about 40 °C per DS‐unit (from 160 to 41 °C) as DS rose from 1 to 3. Mixed esters, cellulose derivatives with acetate and trifluoroethoxy acetate substituents (CAT), exhibited glass‐to‐rubber and melting transitions by DSC. A linear relationship between both T_g and T_m with respect to DS was recorded with the T_g and T_m separated by 30° to 40 °C. This is consistent with cellulose esters described elsewhere. Surprisingly, the T_g's of CT and CAT were found to be identical when the DS was equivalent to the DS of the fluoro substituents (DS_F). © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 486–494, 2000     

Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Cellulose‐based macroinitiator for crosslinked poly(butyl methacrylate‐co‐pentaerythritol triacrylate) oil‐absorbing materials by SET‐LRP

Cellulose produced from cotton fibers was used as substrate for synthesis of oil‐absorbing materials by single electron transfer‐living radical polymerization. The cellulose macroinitiator was prepared by esterification of hydroxyl group with 2‐bromoisobutyryl bromide (BiBB), followed by grafting with butyl methacrylate (BMA) and pentaerythritol triacrylate (PETA) to render a three‐dimensional architecture. The polymerization was catalyzed by Cu(0) powder/hexamethylenetetramine (HMTA) and performed in N,N‐dimethylformamide (DMF). Effects of cellulose, catalyst, reaction temperature, and time were investigated in detail. The maximum oil absorption to chloroform and toluene could reach 29.0 and 15.4 g·g^?1, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Vanadium alkoxide catalyzed polymerization of vinyl chloride

The polymerization of vinyl chloride (VC) with vanadium complex/alkylaluminum catalyst was investigated. In the case of polymerization with vanadium oxytriethoxide (VO(OEt)₃), poly(vinyl chloride) was obtained in a good yield. The effect of cocatalyst, solvent, and cocatalyst/precatalyst ratio was observed. The structure of the polymer obtained with VO(OEt)₃/i‐Bu₃Al catalyst consisted of regular head‐to‐tail sequence and isobutyl chain‐end structure. VO(OEt)₃/alkylaluminum catalyst was able to copolymerize VC with styrene, 1‐butene, methyl methacrylate, and methyl acrylate. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of O‐(2,3‐dihydroxypropyl) cellulose in NaOH/urea aqueous solution: As a precursor for introducing “necklace‐like” structure

O‐(2,3‐dihydroxypropyl) cellulose (DHPC) samples were synthesized by etherification of cellulose with glycidol (GLY) in a NaOH/urea aqueous solution system under different reaction conditions, so that they had different degrees of ether substitution (DS) in both the overall and regional distributions. The characterization was made by NMR spectroscopy in order to clarify the effects of the molar ratio of in‐fed GLY to anhydroglucose unit and of the reaction temperature not only on the total and regional DSs but also on the molar substitution (MS_dhp) for the multireactive dihydroxypropyl group. The evaluation of MS_dhp was performed after complete propionylation of each DHPC sample. Determination of molecular weights was also conducted on the propionylated DHPCs by GPC analysis. As a preliminary extension, butyralization of DHPC was undertaken in aqueous solution by using p‐toluenesulfonic acid as catalyst together with butyraldehyde (BuA). Two‐dimensional NMR (¹H–¹³C gHSQC) spectra measurements revealed that the products contained butyral groups, owing to dehydration‐cyclization between the BuA‐carbonyl and the duplicate hydroxyls in the side chain of DHPC. Such butyral derivatives of cellulose are expected to be a promising functional material parallel or superior to poly(vinyl butyral) available for safety glass interlayers, etc. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3590–3597     

Reactions of vinyl ethers with 2‐cyano‐2‐propyl and benzoyloxy radicals

tert‐Butyl, cyclohexyl, n‐propyl, and n‐dodecyl vinyl ethers have been used as comonomers with styrene and methyl methacrylate using ¹³C‐enriched samples of azobis(isobutyronitrile) and benzoyl peroxide as initiators at 60°C. Examination by ¹³C‐NMR spectroscopy of either (¹³CH₃)₂C(CN) or Ph¹³COO end‐groups in the products has shown that the vinyl ethers have low reactivities toward the 2‐cyano‐2‐propyl radical but high reactivities toward the benzoyloxy radical. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 771–777, 1999