Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.     

Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Crystallization behavior and morphology of poly(ethylene‐co‐trimethylene terephthalate)s

The melt crystallization behaviors and crystalline structures of poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate), and poly(ethylene‐co‐trimethylene terephthalate) (PETT) were investigated with differential scanning calorimetry (DSC), polarized optical microscopy (POM), and X‐ray diffraction at various crystallization temperatures (T_cs). The PETT copolymers were synthesized via the polycondensation of terephthalate with ethylene glycol and trimethylene glycol (TG) in various compositions. The copolymers with 69.0 mol % or more TG or 31.0 mol % or less TG were crystallizable, but the other copolymers containing 34–56 mol % TG were amorphous. The DSC isothermal results revealed that the addition of a small amount of flexible TG (up to 21 mol %) to the PET structure slightly reduced the formation of three‐dimensional spherulites. A greater TG concentration (91–100%) in the copolyesters changed the crystal growth from two‐dimensional to three‐dimensional. The DSC heating scans after the completion of isothermal crystallization at various T_cs showed three melting endotherms for PET, PETT‐88, PETT‐84, and PETT‐79 and four melting endotherms for PETT‐9 and PETT. The presence of an additional melting endotherm could be attributed to the melting of thinner and imperfect copolyester crystallites. Analyses of the Lauritzen–Hoffman equation demonstrated that PETT‐88 had the highest values of the product of the lateral and folding surface free energies, and this suggested that the addition of small amounts of flexible trimethylene terephthalate segments to PET disturbed chain regularity, thus increasing molecular chain mobility. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4255–4271, 2004     

Aging and cold crystallization of melt‐extruded poly(trimethylene terephthalate) films

We analyzed the thermal crystallization, glass‐transition behavior, and mechanical properties of melt‐extruded poly(trimethylene terephthalate) (PTT) films to investigate their physical aging and annealing effects. The physical aging and annealing of PTT films had an influence on the glass‐transition temperature, recrystallization behavior, and mechanical properties. When samples were aged at an ambient temperature, the crystallization temperature decreased largely within 5 h, the heat of crystallization increased, and the breaking stress and breaking elongation increased. The glass‐transition temperature of annealed samples, which was obtained from differential scanning calorimetry and dynamic mechanical measurements, increased with increasing annealing temperature below 80 °C but decreased above that temperature. In addition, the glass‐transition temperature and modulus of annealed samples were largely affected by the annealing time; in particular, they increased sharply within 1 h on annealing at 50 °C. Consequently, the change in the glass‐transition temperature on annealing was ascribed to the fact that the molecular constraint due to recrystallization and the mobility of rigid amorphous PTT chains competed with each other, being dependent on the annealing temperature. The mechanical properties of aged samples were closely related to their cold‐crystallization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1920–1927, 2001     

Non-isothermal crystallization kinetics of poly(trimethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends

The glass-transition temperature and non-isothermal crystallization of poly(trimethylene terephthalate)/poly(ethylene 2,6-naphthalate) (PTT/PEN) blends were investigated by using differential scanning calorimeter (DSC). The results suggested that the binary blends showed different crystallization and melting behaviors due to their different component of PTT and PEN. All of the samples exhibited a single glass-transition temperature, indicating that the component PTT and PEN were miscible in amorphous phase. The value of T_g predicted well by Gordon-Taylor equation decreased gradually with increasing of PTT content. The commonly used Avrami equation modified by Jeziorny, Ozawa theory and the method developed by Mo were used, respectively, to fit the primary stage of non-isothermal crystallization. The kinetic parameters suggested that the PTT content improved the crystallization of PEN in the binary blend. The crystallization growth dimension, crystallization rate and the degree of crystallinity of the blends were increased with the increasing content of PTT. The effective activation energy calculated by the advanced iso-conversional method developed by Vyazovkin also concluded that the value of E_a depended not only on the system but also on temperature, that is, the binary blend with more PTT component had higher crystallization ability and the crystallization ability is increased with increasing temperature. The kinetic parameters U^* and K_g were also determined, respectively, by the Hoffman-Lauritzen theory.     

Thermal and crystallization characteristics of poly(trimethylene terephthalate)/poly(ethylene naphthalate) blends

Poly(trimethylene terephthalate) (PTT)/poly(ethylene naphthalate) (PEN) blends were miscible in the amorphous state in all of the blend compositions studied, as evidenced by a single, composition-dependent glass transition temperature (T_g) observed for each blend composition. The variation in the T_g value with the blend composition was well predicted by the Gordon-Taylor equation, with the fitting parameter being 0.57. The cold-crystallization peak temperature decreased with increasing PTT content, while the melt-crystallization peak temperature decreased with increasing amount of the minor component. The subsequent melting behavior after both cold- and melt-crystallization exhibited melting point depression, in which the observed melting temperatures decreased with increasing amount of the minor component. During melt-crystallization, both components in the blends crystallized concurrently just to form their own crystals. The blend with 60% w/w of PTT exhibited the lowest total apparent degree of crystallinity.     

Crystallization, morphology, and dynamic mechanical properties of poly(trimethylene terephthalate)/clay nanocomposites

The poly(trimethylene terephthalate) (PTT)/clay nanocomposite has been successfully prepared via melt intercalation using a co-rotating twin screw extruder. The nanocomposite was characterized by wide angle X-ray diffraction (WAXD), transmission electron microscope (TEM), differential scanning calorimetry (DSC), polarized light microscope (PLM) and dynamic mechanical analysis (DMA). The nanocomposite forms an exfoliated structure, which can be observed by WAXD and TEM. The effect of clay layers on the crystallization behaviors of PTT was studied through isothermal and non-isothermal crystallization methods. The results suggest that the introduction of nanosize clay layers accelerates the crystallization rate of PTT and the clay layers act as nucleation agents. The morphology of spherulites was investigated with PLM and the result is well in agreement with crystallization kinetics. DMA shows that glass transition temperature (T_g) and storage modulus (E^′) of the PTT matrix of the nanocomposite are higher than those of pure PTT.     

Effect of a silicate filler on the crystal morphology of poly(trimethylene terephthalate)/clay nanocomposites

A series of intercalated poly(trimethylene terephthalate) (PTT)/clay nanocomposites were prepared in a twin‐screw extruder by the melt mixing of PTT with either quaternary or ternary ammonium salt‐modified clays. The morphology and structure, along with the crystallization and melting behavior, and the dynamic mechanical behavior of the composites were characterized by X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and dynamic mechanical thermal analysis. The results showed that the PTT chains could undergo center‐mass transport from the polymer melt into the silicate galleries successfully during the blending and extrusion process. More coherent stacking of the silicate layers was reserved at higher clay concentrations and shorter blend times. Compared with conventionally compounded composites, the nanoscale‐dispersed organophilic clays were more effective as crystal nucleation agents. The influence of the nanosilicates on the crystallization and melting behavior of PTT became distinct when the concentration of clay was around 3 wt %. The changes in the crystallization behavior of the polymer/clay nanocomposites depended not only on the size of the silicates but also on the intrinsic crystallization characteristics of the polymers. The resulting nanocomposites showed an increase in the dynamic modulus of PTT and a decrease in the relaxation intensity (both in loss modulus and loss tangent magnitude). © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2275–2289, 2003     

New super‐tough poly(butylene terephthalate) materials based on compatibilized blends with metallocenic poly(ethylene‐octene) copolymer

New super‐tough poly(butylene terephthalate) (PBT)/poly(ethylene‐octene) copolymer (PEO) blends containing 2 wt% poly(ethylene‐co‐glycidyl methacrylate) (EGMA) as a compatibilizer were obtained by extrusion and injection molding. The blends comprised of an amorphous PBT‐rich phase with some miscibilized EGMA, a pure PEO amorphous phase, and a crystalline PBT phase that was not influenced by the presence of either PEO or EGMA. The blends showed a fine particle size up to 20 wt% PEO content. Super‐tough blends were obtained with PEO contents equal to or higher than 10%. The maximum toughness was very high (above 710 J/m) and was attained with 20% PEO without chemical modification of the commercial components used. Copyright © 2003 John Wiley & Sons, Ltd.     

Synergistic mechanical behaviour and improved processability of poly(ether imide) by blending with poly(trimethylene terephthalate)

Fully miscible poly(ether imide) (PEI)/poly(trimethylene terephthalate) (PTT) blends were obtained by melt mixing in an extruder followed by injection moulding. The viscosity of PEI, represented by the pressure at the extruder output, almost halved upon the addition of only 10% PTT, allowing the use of PEI in applications where either complex parts or thin sections must be moulded. The modulus of elasticity showed a synergistic behaviour which was absolute (modulus higher than that of any of the two components) in the blend with 10% PTT. This was attributed mainly to the decrease in specific volume upon blending. The additional absolute synergism in the yield stress of PEI‐rich blends and their ductile nature depict a set of properties that make these new materials attractive in a number of new applications. Copyright ­© 2003 John Wiley & Sons, Ltd.     

Correlation between melting behavior and ringed spherulites in poly(trimethylene terephthalate)

The lamellar types as revealed by the multiple melting peaks and possible mechanisms of ringed spherulites in poly(trimethylene terephthalate) (PTT) were analyzed with differential scanning calorimetry (DSC), optical microscopy, and scanning electron microscopy. Several interesting correlations were found. If PTT is melt‐crystallized in a certain temperature range, it shows multiple melting peaks and rings in PTT. Once rings are formed in the original melt‐crystallized PTT, they do not disappear but persist and become even more apparent upon postcrystallization annealing at higher temperatures. Furthermore, for PTT that is capable of exhibiting ringed spherulites, a temperature range exists where rings do not form. This behavior can be interpreted in relation with the demonstrated thermal behavior in PTT. Reorganization took place upon postcrystallization scanning or annealing to or at higher temperatures. A postulation was proposed and rigorously tested with evidence to correlate the ringed spherulites and melting behavior. Rings in PTT may be related to multiple lamellae in the spherulites. Consequently, if a temperature of crystallization is selected so that there is only one type of lamella in the spherulites, then there should be no rings. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 80–93, 2002     

A main‐chain phosphorus‐containing poly(trimethylene terephthalate) copolyester: synthesis,characterization, and flame retardance

In order to improve the flame retardancy of the semi‐biobased polyester, poly(trimethylene terephthalate) (PTT), bis‐4‐carboxyphenyl phenyl phosphine oxide (BCPPO) was used as a third monomer to synthesize a novel main‐chain phosphorus‐containing copolyester, poly(trimethylene terephthalate‐co‐BCPPO)s (PTTBP), through melt polycondensation. Phosphorus analysis of the resulting polymers suggests that BCPPO has been introduced to PTT chain successfully. ¹H and ³¹P nuclear magnetic resonance spectra further confirm the random chemical structure. The thermal behavior was investigated by differential scanning calorimetry and thermogravimetric analysis. The introduction of BCPPO to PTT lowered the melting point and crystallization ability because of the random copolymerization and the rigid structure of BCPPO, and the thermal stabilities of PTTBP were improved in air but decreased in nitrogen. Rheological investigations showed that the complex viscosities of all the samples were independent of frequency at low frequency (say lower than 100 rads), and shear thinning effect occurred at higher frequency. The cone calorimeter was used to test the fire behavior of PTTBP, and the results suggested that the novel copolyester had good flame retardance. Copyright © 2011 John Wiley & Sons, Ltd.     

Reaction-induced miscibility in blends comprised of bisphenol-A polycarbonate and poly(trimethylene terephthalate)

The inherent miscibility and effects of reaction-induced changes on the phase behaviour of blends of poly(trimethylene terephthalate) (PTT) with bisphenol-A polycarbonate (PC) were studied. The as-prepared (solution-cast) blends exhibited two well-spaced and separated glass transition temperatures (T_gs) and a heterogeneous phase-separated morphology, indicating an immiscible system. However, after annealing at high temperature (at 260 °C), the blends original two T_gs merged into one single T_g, and the annealed blends exhibited a homogeneous morphology, and turned from having a semicrystalline into having an amorphous nature upon extended annealing. The annealing-induced changes of phase behaviour in the blends were analyzed. The homogenization process of the blends upon heating is attributed to chemical transreactions between the PTT and PC chain segments, as evidenced with FT-IR characterization. The IR result showed a new aryl C-O vibration peak at 1,070 cm^–1 for the annealed blends, which is characteristic of an aromatic polyester structure formed from exchange reactions between PTT and PC. The transreactions between PTT and PC led to a random copolymer comprised of PC/PTT segments, which is believed to serve as a compatibilizer at the beginning stage of transreactions, but at later stage, the random copolymer became the main species of blends and turned to a homogeneous and amorphous phase.     

Relaxation behavior of poly(ethylene terephthalate)/poly(ethylene naphthalene 2,6‐dicarboxylate) blends prepared by cryogenic blending

A method including cryogenic grinding, melt pressing from the molten state, and quenching was used to prepare blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) in which the two phases were highly dispersed. The effect of melt‐pressing times on the thermal properties and relaxation behavior of PET/PEN films were characterized with differential scanning calorimetry and dielectric spectroscopy. For short melt‐pressing times, two glass‐transition, two crystallization, and two melting peaks were observed, indicating the presence of PET‐rich and PEN‐rich phases in these blends. Longer melt‐pressing times revealed a single glass transition and a single α‐relaxation process, showing that PET–PEN block copolymers were likely to be formed during the melt pressing. The experimental findings were examined in terms of the transesterification reactions between the blend components, as revealed by ¹H NMR measurements. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2570–2578, 2002     

Influence of a terpolymer compatibilizer on the nanostructure of poly(trimethylene terephthalate)/montmorillonite nanocomposites

The use of a compatibilizer to improve the interactions between poly(trimethylene terephthalate) (PTT) and an organically treated montmorillonite (MMT) clay was studied. Nanocomposites, with and without compatibilizer, were obtained using a torque rheometer; their nanostructures were analyzed by wide angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), steady state and dynamic rheological measurements, and Fourier transform infrared analysis (FT‐IR). Only intercalated structures were obtained when no compatibilizer was added, independent of the mixing method (one or two steps); when the compatibilizer was added, however, intercalated and exfoliated structures were obtained, depending on the masterbatch composition. When the PTT was not present in the masterbatch, two‐phase exfoliated structures were obtained, with a disperse phase composed of nanoclay's lamellas and reticulated compatibilizer and a matrix phase composed of PTT. The compatibilizer cured due to the presence of the nanoclay's surfactant; a mechanism of cure was proposed in which the epoxide rings of the compatibilizer reacted with the hydroxyl groups of the nanoclay's surfactant, forming ether cross‐linkages. It was also concluded that in order to obtain one‐phase exfoliated structures the two steps mixing method using a masterbatch composition of 50 wt% of PTT, 25 wt% of compatibilizer, and 25 wt% of nanoclay gave the best results; after further dilution in the PTT, an exfoliated nanocomposite with a final concentration of 5 wt% of compatibilizer and 5 wt% of nanoclay was obtained. Copyright © 2008 John Wiley & Sons, Ltd.     

Compatibility and thermal properties of poly(3‐hydroxybutyrate)/poly(glycidyl methacrylate) blends

Poly(3‐hydroxybutyrate) (PHB)/poly(glycidyl methacrylate) (PGMA) blends were prepared by a solution‐precipitation procedure. The compatibility and thermal decomposition behavior of the PHB/PGMA blends was studied with differential scanning calorimetry, thermogravimetric analysis, and differential thermal analysis (DTA). The blends were immiscible in the as‐blended state, but for the blends with PGMA contents of 50 wt % or more, the compatibility was dramatically changed after 1 min of annealing at 200 °C. In addition, PHB/PGMA blends showed higher thermal stability, as measured by maximum decomposition temperatures and residual weight during thermal degradation. This was probably due to crosslinking reactions of the epoxide groups in the PGMA component with the carboxyl chain ends of PHB fragments during the degradation process, and the occurrence of such reactions can be assigned to the exothermic peaks in the DTA thermograms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 351–358, 2002     

Nonisothermal cold‐crystallization kinetics of poly(trimethylene terephthalate)

The nonisothermal cold‐crystallization kinetics and subsequent melting behavior of poly(trimethylene terephthalate) (PTT) were investigated with differential scanning calorimetry. The Avrami, Tobin, and Ozawa equations were applied to describe the kinetics of the crystallization process. Both the Avrami and Tobin crystallization rate parameters increased with the heating rate. The Ozawa crystallization rate increased with the temperature. The ability of PTT to crystallize from the glassy state at a unit heating rate was determined with Ziabicki's kinetic crystallizability index, which was found to be about 0.89. The effective energy barrier describing the nonisothermal cold‐crystallization process of PTT was estimated by the differential isoconversional method of Friedman and was found to range between about 114.5 and 158.8 kJ mol^?1. In its subsequent melting, PTT exhibited double‐melting behavior for heating rates lower than or equal to 10 °C min^?1 and single‐melting behavior for heating rates greater than or equal to 12.5 °C min^?1. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4151–4163, 2004     

Morphology of poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) segmented copolyesters

Segmented copolyesters, namely, poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) (PBT‐PETIS), were synthesized with the melting transesterification processing in vacuo condition involving bulk polyester produced on a large scale (PBT) and ternary amorphous random copolyester (PETIS). Investigations on the morphology of segmented copolyesters were undertaken. The two‐phase morphology model was confirmed by transmission electron microscopy and dynamic mechanical thermal analysis. One of the phases was composed of crystallizable PBT, and the other was a homogeneous mixture of PETIS and noncrystallizable PBT. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2257–2263, 2003     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010