Nanosized bismuth titanate (Bi4Ti3O12) system drive through auto-combustion process by using suspension titania (TiO2)

Bismuth titanate (Bi₄Ti₃O₁₂) was developed by means of titanium oxide (TiO₂) suspension in auto-combustion process at 220 °C to get nanosized (20 ± 5 nm) bismuth titanate (Bi₄Ti₃O₁₂) powder. Complete piezoelectric phase (tetragonal) was obtained after calcination at 700 °C. Dilatometery of compacts was performed to find out sintering temperature. On the basis of shrinkage results, compacts were sintered at 750, 800, and 850 °C for 2 h. After sintering single phase was obtained with orthorhombic structure analyzed by X-ray diffraction and also investigated by Rietveld method. High-resolution scanning electron microscopy revealed that fine plate-like structure which is a characteristic of BIT powder can be obtained at 850 °C. Sintering results indicate that density and average grain size increase with the increasing temperature. A maximum of about 90 % of the theoretical density was achieved for the sintered product at 850 °C.     

The electrical properties of chemically obtained barium titanate improved by attrition milling

Barium titanate ceramics were prepared using the nanopowder resulting from a polymeric precursor method, a type of modified Pechini process. The obtained nanopowder was observed to agglomerate and in order to de-agglomerate the powder and enhance the properties of the barium titanate the material was attrition milled. The impact of this attrition milling on the electrical properties of the barium titanate was analysed. The temperature dependence of the relative dielectric permittivity showed three structural phase transitions that are characteristic for ferroelectric barium titanate ceramics. The relative dielectric permittivity at the Curie temperature was higher for the attrition-treated sample than for the non-treated barium titanate. The dielectric losses were below 0.04 in both barium titanate ceramics. The grain and grain-boundary contributions to the total resistivity were observed using impedance analyses for both ceramics. A well-defined ferroelectric hysteresis loop and piezoelectric coefficient d₃₃ = 150 pC/N were obtained for the ceramics prepared from the de-agglomerated powder. In this way we were able to demonstrate that by attrition milling of chemically obtained powders the ferroelectric and piezoelectric properties of the ceramics could be enhanced.     

Low temperature nanostructured lithium titanates: controlling the phase composition, crystal structure and surface area

Low temperature lithium titanate compounds (i.e., Li₄Ti₅O₁₂ and Li₂TiO₃) with nanocrystalline and mesoporous structure were prepared by a straightforward aqueous particulate sol–gel route. The effect of Li:Ti molar ratio was studied on crystallisation behaviour of lithium titanates. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) revealed that the powders were crystallised at the low temperature of 500 °C and the short annealing time of 1 h. Moreover, it was found that Li:Ti molar ratio and annealing temperature influence the preferable orientation growth of the lithium titanate compounds. Transmission electron microscope (TEM) images showed that the average crystallite size of the powders annealed at 400 °C was in the range 2–4 nm and a gradual increase occurred up to 10 nm by heat treatment at 800 °C. Field emission scanning electron microscope (FE-SEM) analysis revealed that the deposited thin films had mesoporous and nanocrystalline structure with the average grain size of 21–28 nm at 600 °C and 49–62 nm at 800 °C depending upon the Li:Ti molar ratio. Moreover, atomic force microscope (AFM) images confirmed that the lithium titanate films had columnar like morphology at 600 °C, whereas they showed hill-valley like morphology at 800 °C. Based on Brunauer–Emmett–Taylor (BET) analysis, the synthesized powders showed mesoporous structure containing pores with needle and plate shapes. The surface area of the powders was enhanced by increasing Li:Ti molar ratio and reached as high as 77 m²/g for the ratio of Li:Ti = 75:25 at 500 °C. This is one of the smallest crystallite size and the highest surface areas reported in the literature, and the materials could be used in many applications such as rechargeable lithium batteries and tritium breeding materials.     

Sol–gel combustion synthesis of BNBT powders

Ba-modified bismuth sodium titanate with composition 0.94[(Bi_0.5Na_0.5)TiO₃]-0.06BaTiO₃ (BNBT) was prepared by a citrate nitrate sol–gel combustion method. The sol was obtained using barium acetate, bismuth nitrate, sodium nitrate and a peroxo-citrate complex of titanium isopropoxide as starting precursors. Various molar ratios of citrate/nitrate (C/N) were considered for the sol production. The corresponding gels were fired at different temperatures (300, 400, 500 °C) in order to evaluate the conditions necessary to obtain the decomposition of the precursors and the formation of the pure BNBT perovskitic phase in a single step. The best conditions to obtain the desired phase are: (C/N) = 0.2, and combustion temperature of 500 °C. Ball milled powders were densified at a temperature 100 °C lower than the one generally used for powder produced with the conventional mixed oxide route. The electrical properties are comparable to those reported for conventionally prepared materials.     

Thermal behavior of BST//PVDF ceramic–polymer composites

In this paper, we report the results of a study of microstructure and thermal behavior of ceramic–polymer composites composed of barium strontium titanate Ba_0.6Sr_0.4TiO₃ (BST60/40) and polyvinylidene fluoride (PVDF). The Ba_0.6Sr_0.4TiO₃ ceramic powder was prepared by the sol–gel method. Thermal evolution of the dried gel as well as ceramic powder was studied by simultaneous thermal analysis. The composite BST60/40//PVDF was obtained by hot pressing method for volume fraction of BST60/40 ceramic powder c _v = 50 %. The morphology of BST60/40//PVDF composite powder was observed by transmission electron microscopy and the morphology of BST60/40//PVDF composite sample was observed by scanning electron microscopy. Temperature dependence of dielectric constant and dielectric loss factor of BST60/40//PVDF composites was measured in the frequency range of f = (10 × 10³–1 × 10⁶) Hz. Dynamic mechanical properties of BST60/40//PVDF composites were measured by dynamic mechanical thermal analysis DMTA.     

溶胶-凝胶法制备Ba_(0.6)Sr_(0.4)TiO_3陶瓷纤维

首次采用乙酰丙酮为钛醇盐的稳定剂,醋酸钡、醋酸锶和钛酸丁酯为原料,无水乙醇-冰醋酸作为溶剂,利用Sol-Gel法于1100℃得到单一钙钛矿相钛酸锶钡陶瓷纤维.用TG、XRD、SEM等手段对产物进行表征.     

Synthesis of highly pure nanocrystalline and mesoporous CaTiO3 by a particulate sol–gel route at the low temperature

The low temperature perovskite-type calcium titanate (CaTiO₃) thin films and powders with nanocrystalline and mesoporous structure were prepared by a straightforward particulate sol–gel route. The prepared sol had a narrow particle size distribution about 17 nm. X-ray diffraction and Fourier transform infrared spectroscopy revealed that, the synthesized powders had highly pure and crystallized CaTiO₃ structure with preferable orientation growth along (1 2 1) direction at 400–800 °C. The activation energy of crystal growth was calculated 5.73 kJ/mol. Furthermore, transmission electron microscope images showed that the average crystallite size of the powders annealed at 400 °C was around 3.5 nm. Field emission scanning electron microscope analysis and atomic force microscope images revealed that, the deposited thin films had uniform, mesoporous and nanocrystalline structure with the average grain size in the range 33–39 nm depending on annealing temperature. Based on Brunauer–Emmett–Teller (BET) analysis, the synthesized powders showed mesoporous structure with BET surface area in the range 51–21 m²/g at 400–800 °C. One of the smallest crystallite size and one of the highest surface areas reported in the literature is obtained which can be used in many applications, such as photocatalysts.     

Sorption of Strontium Ions on Potassium-Titanate Nanoparticles of Various Morphology Obtained under Hydrothermal Conditions

The results of the study of the interaction of an aqueous solution of strontium nitrate with potas-sium-titanate nanoparticles of different morphology obtained by the hydrothermal method are reported. Comparative analysis showed the advantage of nanotubes as sorbents over nanolayers and nanowires. As can be seen from the experiment conducted with nanotubes containing aluminum, an amount of strontium sorbed from the solution rises with increasing temperature: at 50°C the absorption by the tubular matrix was ≈ 0.76 × 10^?3 mol g^?1, and at 80°C that was ≈ 2.02 × 10^?3 mol g^?1. Nanotube samples doped with magnesium had the best sorption characteristics: After 5 h of keeping in a solution at 80°С, the content of strontium in them was ≈3.65 × 10^?3 mol g^?1. The results show the promise of using potassium titanate nanoparticles to extract strontium from aqueous solutions.

     

Solvent‐free synthesis of polyacrylamide by frontal polymerization

Polymerization and characterization of polyacrylamide prepared by frontal polymerization are described. Frontally polymerized polyacrylamide is imidized and crosslinked during polymerization. Imide formation was determined by elemental analysis. The addition of commercial polyacrylamide or barium carbonate to the monomer (acrylamide) and initiator (potassium persulfate) decreased the reaction temperature from 235 °C to < 100 °C, thereby reducing imide formation. The commercial polyacrylamide‐diluted product, frontally polymerized polyacrylamide‐diluted product, and the barium carbonate‐diluted product were characterized by IR, TGA, and elemental analysis. Molecular weights of barium carbonate‐diluted samples were determined by light scattering and found to be on the order of one million. Conversion of the barium carbonate‐diluted product was determined to be 76 ± 6%, independent of the amount of diluent over the range 0.8:1–1.5:1. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1129–1135, 2000     

Synthesis of barium titanate/polymer composites from metal alkoxide

Barium titanate (BaTiO₃)/polymer composite was successfully synthesized by methacryltriisopropoxytitanium (MTPT) and barium alkoxide. MTPT undergoes radical polymerization using azobisisobutyronitrile at temperatures from 90 to 150°C. ¹H NMR spectra showed that MTPT reacted with barium alkoxides yielding a complex alkoxide. BaTiO₃ particles/polymer was formed after the polymerization and hydrolysis of the complex alkoxide. The transmission electron microscopic observation revealed that crystalline BaTiO₃ particles of around 3 nm in size were dispersed in the polymer matrix.     

Liquid-phase synthesis of barium acetatotitanyl and barium oxalatotitanyl as intermediates for preparing nanosized barium titanate

Liquid-phase methods (an oxalate process in aqueous solution and a semialkoxide sol-gel process in anhydrous acetic acid) were used to prepare barium acetatotitanyl (BAT) and barium oxalatotitanyl (BOT), which are potential fillers for electrorheological liquids, and to prepare barium titanate during heat treatment of the aforementioned intermediates at 1200°C. The materials were characterized using electron microscopy, FTIR spectroscopy, and thermal analysis. The particle size was 80 to 100 nm for BAT powders and 20 to 50 nm for BOT powders. X-ray spectra of the powders dried at 120°C contain reflections from a barium titanate phase. The dielectric spectra of the materials synthesized were studied for suspensions in PMS-20 silicone oil over the frequency range from 25 to 10⁶ Hz up to 4 kV/mm. The dielectric parameters of BOT suspensions decrease hyperbolically with rising alternate current frequency, whereas BAT suspensions give rise to a relaxation dielectric spectrum with relaxation times on the order of 10⁻³ s.     

Effect of the synthesis temperature of sodium nonatitanate on batch kinetics of strontium-ion adsorption from aqueous solution

Sodium titanate materials are promising inorganic ion exchangers for the adsorption of strontium from aqueous solutions. Sodium nonatitanate exhibits a layered structure consisting of titanate layers and exchangeable sodium ions between the layers. The materials used in this study include samples synthesized by a hydrothermal method at temperatures between 60 °C and 200 °C. Their structure, composition, and morphology were investigated with X-Ray diffraction measurements; thermogravimetric, compositional and surface area analyses, and scanning electron microscopy. The structure, composition, and morphology depended on the synthesis temperature. Batch kinetics experiments for the removal of strontium from aqueous solutions were performed, and the data were fitted by a pseudo-second-order reaction model and a diffusive model. The strontium extraction capacity also depended on the synthesis temperature and exhibited a maximum for samples synthesized at 100 °C. The sorption process occurs in one or two diffusion-controlled steps that also depend on the synthesis temperature. These diffusion-limited steps are the boundary-layer diffusion and intra-particle diffusion in the case of pure nonatitanate synthesized at temperatures lower than 170 °C, and only intra-particle diffusion in the case of nonatitanate synthesized at 200 °C.     

Nano-alumina by gel combustion, its thermal characterization and slurry-based coating on stainless steel surface

Gel combustion method was used to prepare nano-alumina from aluminum nitrate and stoichiometric amount of glycine as fuel. The TG–DTA pattern of the as-prepared powder (combustion product) exhibited exotherms with peaks around 500 and 900 °C accompanied with loss of weight of 25 and 5 % attributed to burning away of carbon left behind and decomposition of residual reaction intermediates left behind, respectively. Even though mass stability is attained above 900 °C, the DTA exhibited an exotherm around 1,150 °C attributed to transformation of gamma to alpha form of alumina. The XRD studies revealed that the powder heated to 900 °C was chemically pure nano-crystalline alumina while that heated above 1,150 °C was crystalline alpha form. As nano-crystalline powders are sinter-active, the nano-crystalline alumina formed by calcination at 900 °C was used to form the coating. A morphological feature of the agglomerates of nano-alumina powders were evaluated using SEM. The powder was de-agglomerated by wet grinding method. The dispersion conditions to form slurry using 900 °C calcined powder for slurry-based coating was optimized using zeta-potential studies, and it was found to exhibit a maximum value of ?45 mV at a pH of 9. After 8 h of grinding, the median agglomerate size reduced to 2 μm. Rheological studies exhibited desired pseudoplastic behavior in the range of 10–20 vol.% of solid while the slurry with 15 vol.% only form crack free, dense, and adherent coating after heat treatment at 1,150 °C. The morphology of the coating was found to be uniform and dense.     

Synthesis of nanosized carbonated apatite by a modified Pechini method: hydroxyapatite nucleation from a polymeric matrix

Pechini method is a materials synthesis method based on the preparation of a polymeric matrix. The advantage of this method is the ability to obtain materials with different particle sizes depending on the synthesis condition with a homogeneous distribution. In this work, carbonated hydroxyapatite (c-OHAp) nanoparticles were obtained by a modified Pechini method. To obtain the polymeric precursor of the c-OHAp, the polymeric matrix was prepared through a polyesterification reaction between citric acid and ethylene-glycol. Adding calcium hydroxide and ortophosphoric acid in aqueous solutions, raising the temperature up to 140 °C/2 h and keeping constant the pH at 8. The polymeric matrix was calcinated at different ranges of temperature from 200 to 600 °C in order to obtain the c-OHAp powder. The results show the presence of c-OHAp a as unique phase. The thermal analysis indicates that the c-OHAp phase was obtained at 600 °C. The particle size of the obtained material was <50 nm.     

Amperometric glucose biosensor based on platinum nanoparticle encapsulated with a clay

Electrically conductive hollow nanospheres with an average diameter between 100 and 200 nm were prepared via a one-step polymerization of aniline in the presence of lignosulfonate (LS) by using ammonium persulfate (APS) as the oxidant. The LS concentration and molar ratio between APS and aniline, the temperature and time for polymerization were adjusted to optimize morphology, structure and electrochemical properties. Uniform hollow nanospheres are best obtained at a concentration of 18 wt% of LS, at a polymerization temperature at 25 °C, at an APS/aniline molar ratio of 1:1, and at a polymerization time of 1 to 12 h. This kind of preparation of nanospheres represents a simple and general route to polymer hollow nanospheres of controllable size, high stability, and optimizable electroconductivity.     

Selected-area sol-gel deposition of barium strontium titanate thin films on thermally oxidized silicon through mediation of self-assembled monolayers

Self-assembled monolayers (SAMs) of octadecyltrichlorosilane (OTS) and mercapto ethanol were used to modify the surface functionality of platinum/titanium or platinum/tantalum bilayer patterns on thermally oxidized silicon wafers. The attachment of OTS to the exposed oxide region made it hydrophobic, while the anchoring of mercapto ethanol to the bilayer pattern turned it hydrophilic. This patterned hydrophobicity and hydrophilicity was exploited to preferentially deposit barium strontium titanate (BST) thin films on the patterned bilayers from an aqueous sol-gel solution. The combination of the SAMs and the sol-gel film formation method allowed direct patterned deposition of BST thin films, which could be useful for on-chip electronic applications. Wet oxygen annealing at 50 °C was sufficient to stabilize the deposited sol-gel coating without adversely affecting the functionality of the OTS, thus permitting multiple dip-coatings to obtain patterned films of a desired thickness. Heat treatment at 750 °C allowed densification and conversion of the sol-gel coatings to perovskite BST films.     

Thermal stability and flammability of polyurethane foams chemically reinforced with POSS

Manganese ferrite nanopowder was prepared by a new solvothermal method, using 1,2 propanediol as solvent and KOH as precipitant. The as-synthesized powder, by solvothermal treatment in autoclave at 195 °C, for 12 h, consisted of fine manganese ferrite nanoparticles. The further thermal treatment of the initial manganese ferrite powder to higher temperature resulted in manganese ferrite decomposition due to Mn(II) oxidation to Mn(III), as observed by X-ray diffraction. FT-IR spectroscopy has evidenced that the oxidation takes place even at 400 °C. The oxidation of Mn(II) to Mn(III) was studied by TG/DSC simultaneous thermal analysis. It was shown that Mn(II) oxidation takes place in a very small extent up to 400 °C. The main oxidation step occurs around 600 °C, when a clear mass gain is registered on TG curve, associated with a sharp exothermic effect on DSC curve. The exothermic effect is smaller in case of the powder annealed at 400 °C, confirming the superficial oxidation of Mn(II) up to 400 °C. In order to avoid Mn(II) oxidation, the powder obtained at 400 °C was further annealed at 800 °C in argon atmosphere, without degassing, when manganese ferrite MnFe₂O₄ was obtained as major crystalline phase (69 %). All manganese ferrite powders showed a superparamagnetic behavior, with maximum magnetization of 51 emu g^?1 in case of the as-synthesized powder, characteristic of magnetic ferrite nanopowders.     

Dielectric and energy storage properties of barium strontium titanate based glass–ceramics prepared by sol–gel method

Ba_0.6Sr_0.4TiO₃ based glass–ceramics were prepared by sol–gel process. Influences of B–Si–O glass content on the microstructure, dielectric, and energy storage properties of the BST based glass–ceramics have been investigated. Perovskite barium strontium titanate phase was found at annealing temperature 800 °C. A secondary phase Ba₂TiSi₂O₈ was detected and lowered by declining the mole ratio of element Si (from 50 to 25 mol%) in glass additive. Microstructural observation indicated that the microstructure homogeneity can be improved by glass addition till 2 mol%, while worsened by excessive glass concentrations. Due to relatively homogeneous microstructure, the maximum discharged energy density and breakdown strength were also obtained in samples with 2 mol% glass additive, which were found to be 0.553 J/cm³ and 43.2 kv/mm, respectively. Microscopic observation of the breakdown area was performed and the mechanical failure, including the formation and accumulation of micro-cracks during the dielectric breakdown process, was considered to be the main cause of dielectric breakdown. Results of the charging and discharging energy densities show that the BST based glass–ceramics prepared by sol–gel method has a potential for pulse power applications.     

Some aspects of the high-temperature behavior of bismuth,strontium and barium on silicon surfaces studied by total reflection X-ray fluorescence spectrometry

Thin films of novel dielectric and ferroelectric materials, such as barium strontium titanate (BST) and strontium bismuth tantalate (SBT), which are scheduled for short-term implementation into standard microelectronic device technology, contain elements like Bi, Sr and Ba which may involve risks with regard to device yield and reliability. Therefore, the high-temperature behavior of bismuth, strontium and barium impurities on Si (100) substrates was studied. Intentionally contaminated Si substrates were annealed at 1000°C under different ambient (inert, oxidizing) by rapid thermal annealing (RTA) or in a furnace and analyzed by total reflection X-ray fluorescence spectrometry (TXRF), vapor phase decomposition/TXRF (VPD/TXRF) and electrolytic metal tracer (Elymat) technique. Ba and Sr are incorporated in the existing or growing oxide during rapid thermal annealing (RTA). Cross-contamination due to gas phase transport may occur in the case of Bi, in particular under N₂ atmosphere, but is of no concern in the case of Ba and Sr. All three contaminants do not exert an influence on the minority carrier lifetime on their own. The results illustrate that TXRF and VPD/TXRF are appropriate techniques for such studies.     

Physical and electrochemical properties of (La0.3Sr0.7)0.93TiO3–δ synthesized by Pechini method as an anode material for solid oxide fuel cells

The lanthanum strontium titanate (LST) has to be calcined at significantly high temperature (above 1,300 °C) to obtain its pure perovskite structure when synthesized by conventional solid-state method, which is main reason for reducing active surface area. In this study, A-site deficient (La_0.3Sr_0.7)_0.93TiO₃ was synthesized by Pechini method. Although the prepared powders were calcined at 600 °C, the pure perovskite structure can be obtained without any secondary phase such as TiO₂. Moreover, the porosity and surface area are 6 times and one order of magnitude higher in the LST powders synthesized by Pechini method than in the powders synthesized by solid-state method. Based on these results, the LST electrode (Pechini) leads to two times lower electrode resistance than the LST electrode (solid-state). Thus, the LST powders synthesized by Pechini can contributes to saving the energy needed for calcination process as well as increasing the porosity and active surface area, enhancing physical and electrochemical properties in SOFC anode.