Synthesis of poly(arylene ether ketone)s bearing skeletal crown ether units for cation exchange membranes

Poly(arylene ether ketone)s (PAEKs) are the most commonly known high‐performance materials used for ion exchange and fuel cell membranes. Described here is the design of novel sulfonated PAEKs (SPAEKs) and nonsulfonated PAEKs containing crown ether units in the main chain, which can be used in sensing applications and ion‐selective membranes. To this end, 4,4′(5′)‐di(hydroxybenzo)‐18‐crown‐6 was synthesized and used as monomer in a step growth polymerization to form crown ether‐containing PAEKs and SPAEKs. The successful synthesis of PAEKs containing 18‐crown‐6 and sulfonate groups was confirmed by gel permeation chromatography, Fourier transform infrared spectroscopy, and nuclear magnetic resonance spectroscopy. Membranes are fabricated from the sulfonated polymers. Potassium ion transport properties of the SPAEK and crown ether‐containing SPAEK membranes are assessed by diffusion dialysis. Potassium ion diffusion in the crown ether‐containing SPAEK membranes is almost four times lower than K⁺ diffusion in the native polymer membranes, without crown ether. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2786–2793     

Water vapor sorption and diffusion in sulfonated aromatic polyamides

In this contribution polyamides with different sulfonation degrees were directly synthesized from a combination of sulfonated and nonsulfonated diamines and isophthaloyl chloride. They were then used as dense membranes to study water sorption and mass transport properties. The polymers were characterized by their inherent viscosity and by spectroscopic methods, and the water vapor unsteady sorption phenomena were studied using a gravimetric technique. The effect of sulfonation substitution concentration in these polymers produces very interesting and original results in a number of properties such as the ionic exchange capacity, water equilibrium sorption and diffusivity. Obtained results are discussed and explained in the light of existing theories. Sorption behavior for polymers with a low sulfonation degree, up to 30%, can be explained with Langmuir equation. With larger substitution degree (40 and 60%) an additional mechanism must be assumed to explain sorption data. Assuming the presence of two phases helps to explain the observed diffusivity results. The mass transport mechanism is assumed to be Fickian. When water activity is low diffusivity systematically decreases as the degree of sulfonation increases. However, as water activity increases less sulfonated and nonsulfonated (PA0, PA20 and PA30) behave completely different from PA40 and PA60. The first group of polymers shows a tendency to decrease the rate of diffusion as water activity increases while the second group shows the opposite behavior, with a maximum in diffusivity at intermediate water activities. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2007–2014, 2007     

Optimizing the monomer structure of polyhedral oligomeric silsesquioxane for ion transport in hybrid organic–inorganic block copolymers

Poly(ethylene oxide)-b-polyhedral oligomeric silsesquioxane (PEO–POSS) mixed with lithium bis(trifluoromethanesulfonyl)imide salt is a nanostructured hybrid organic–inorganic block copolymer electrolyte that may enable lithium metal batteries. The synthesis and characteristics of three PEO–POSS block copolymer electrolytes which only differ by their POSS silica cage substituents (ethyl, isobutyl, and isooctyl) is reported. Changing the POSS monomer structure results in differences in both thermodynamics and ion transport. All three neat polymers exhibit lamellar morphologies. Adding salt results in the formation of a disordered window which closes and gives way to lamellae at higher salt concentrations. The width of disordered window decreases with increasing length of the POSS alkyl chain substituent from ethyl to isobutyl and is absent in the isooctyl sample. Rheological measurements demonstrate good mechanical rigidity when compared with similar all-organic block copolymers. While salt diffusion coefficient and current ratio are unaffected by substituent length, ionic conductivity increases as the length of the alkyl chain substituent decreases: the ethyl substituent is optimal for ion transport. This is surprising because conventional wisdom suggests that ion transport occurs primarily in the PEO-rich domains, that is, ion transport should be unaffected by substituent length after accounting for the minor change in conducting phase volume fraction. © 2020 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2020 © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 363–371     

Water‐mediated transport in ion‐containing polymers

Water‐mediated ion conduction enables high conductivity in hydrated polymer membranes commonly used in electrochemical devices. Understanding the coupling of the absorbed water with the polymer matrix and the dynamics of water inside the polymer network across the full range of length scales in the membrane is important for unraveling the structure–property relationships in these materials. By considering the water behavior in ion‐containing polymers, next‐generation fuel cell membranes are being designed that exceed the conductivity of the state‐of‐the‐art materials and have optimized conductivity and permeability that may be useful in other types of devices such as redox flow batteries. Water–polymer associations can be exploited to tune the transport and mechanical property tradeoffs in these polymers. Measurements of water motion provide important criteria for assessing the factors that control the performance of these types of materials. This review article discusses current understanding of water behavior in ion‐containing polymers and the relationship between water motion and ion and molecular transport. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Carbon nanotubes in emulsion‐templated porous polymers: Polymer nanoparticles,sulfonation, and conductivity

Sulfonated polymers are of interest for ion exchange resins, reaction supports, and membranes for separation, filtration, fuel cells, and electrochemical devices. Sulfonic groups have been introduced into polystyrene (PS) through exposure to sulfuric acid, and carbon nanotubes (CNTs) have been added to polymers to enhance proton conductivity without creating an electronic percolation pathway. PolyHIPEs, emulsion‐templated porous polymers with highly interconnected hierarchical open‐cell porous structures, are synthesized through polymerization in the external phases of high internal phase emulsions (HIPEs). In this article, the synthesis of PS‐based CNT‐filled polyHIPEs, their structure, sulfonation, and conductivity are described. Adding CNT dispersions to the HIPEs produced polymer nanoparticle–covered polyHIPEs from polymerization within the water‐soluble surfactant micelles in the internal aqueous phase droplets. The CNTs migrated from the HIPE's aqueous phase droplets into the HIPE's organic phase and formed interconnected bundles within the polyHIPE walls, reflecting a reduction in the surfactant's ability to disperse the CNTs. The water adsorption in the hygroscopic sulfonated polyHIPEs increased the conductivity by several orders of magnitude. The conductivity of the sulfonated polyHIPE containing CNTs was more than an order of magnitude greater than that of the sulfonated polyHIPEs with no CNTs. The CNTs act as “bridges,” enhancing the connection between existing conductive pathways. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4369–4377     

Confined glassy properties of polymer nanoparticles

For nearly the past two decades, significant effort has been devoted to pursuing an understanding of the glass transition temperature and associated dynamics of polymers confined to the nanoscale. Without question, we know more about the glassy properties of confined polymers today than we knew two decades ago or even a decade ago. Much of our understanding has been obtained via studies on thin polymer films, as they are facile to process and are of substantial technological importance. Nevertheless, studies on polymers confined to other geometries are becoming increasingly more important as we pursue questions difficult to address using thin films and as technology demands the use of confined polymers beyond thin films. In this feature article, we highlight the impact of nanoscale confinement on the glassy properties of polymer nanoparticles. Although the emphasis is placed on contributions from our work, a discussion of the related literature is also presented. Our aim is to elucidate commonalities or fundamental differences in the deviations of glassy properties from the bulk for polymers confined to different geometries. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Improvement of thermal stability of sulfonated polyphosphazenes by introducing a self‐crosslinkable group

We prepared sulfonated polyphosphazenes having various aryloxy substituents, and studied their thermal stabilities and membrane properties. Sulfonated polyphosphazenes were synthesized by the reaction of polydichlorophosphazene with sodium aryloxides and subsequent sulfonation with fuming sulfuric acid. With increasing the degree of sulfonation, the polymers showed higher proton conductivity, but suffered more from swelling in an aqueous solution. We introduced a hydroxymethylphenoxy group onto the phosphazene backbone as a self‐crosslinkable group by reaction of poly(dichlorophosphazene) and a sodium salt of 4‐hydroxymethylphenol. When a film of a sulfonated polymer having a methylol group was heated at 80 °C under vacuum for 1 h, it became insoluble in NMP, indicating the formation of a network structure. We investigated the crosslinking reaction of the polymers by DSC and FTIR. The crosslinking reaction proceeded only in the sulfonated polymers. Because the sulfonated polymers provide acidic protons, the methylol groups became more electrophilic and reacted with neighboring aromatic rings. A condensation reaction between themselves could also occur. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5850–5858, 2008     

Synthesis of sulfonated aromatic poly(ether amide)s and their application to proton exchange membrane fuel cells

A series of wholly aromatic sulfonated poly(ether amide)s (SPEAs) containing a sulfonic acid group on the dicarbonyl aromatic ring were prepared via a polycondensation reaction of sulfonated terephthalic acid (STA), terephthalic acid (TA), and aromatic diamine monomers. The degree of sulfonation was readily controlled by adjusting the monomer feed ratio of STA and TA in the polymerization process, and randomly sulfonated polymers with an ion exchange capacity (IEC) of 1.0–1.8 mequiv/g were prepared using this protocol. The chemical structures of randomly sulfonated polymers were characterized using NMR and FT‐IR spectroscopies. Gel permeation chromatography analysis of SPEAs indicated the formation of high‐molecular‐weight sulfonated polymer. Tough and flexible SPEA membranes were obtained from solution of N,N‐dimethylacetamide, and thermogravimetric analysis of these membranes showed a high degree of thermal stability. Compared with previously reported sulfonated aromatic polyamides, these new SPEAs showed a significantly lower water uptake of 10–30%. In proton conductivity measurements, ODA‐SPEA‐70 (IEC = 1.80 mequiv/g), which was obtained from polycondensation of 4,4′‐oxydianiline and 70 mol % STA, showed a comparable proton conductivity (105 mS/cm) to that of Nafion 117 at 80 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 485–496, 2009     

Hyperbranched polymers 10 years after

It has been about 10 years since the first intentional preparation of hyperbranched polymer was disclosed. Hyperbranched polymers, as well as dendrimers, may find utilities in the areas where the structural uniqueness of these polymers gives merit. There has been much progress in the structural understanding and the methods of synthesis of these polymers. However, functional understanding and utility of these polymers are still in infancy. Better understanding on physical properties of these polymers, such as solubility and miscibility of these polymers in solvents or with polymers, and functional group dependency to the thermal relaxation process are needed for further development of the subject. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A: Polym. Chem. 36: 1685–1698, 1998     

Steric effect and mobility of the alkyl chain in regio‐irregular poly‐3‐alkylthiophenes

The physicochemical properties of polyalkylthiophenes with various side‐chain length were widely investigated in order to reveal the functions of alkyl side‐chains in these polymers. The effects of the side‐chains on the properties of polyalkylthiophenes can be explained by their steric hindrance and mobility. The steric hindrance of alkyl chain affected not only the polymerization mechanism of the monomers but also the redox potential, interchain distance, charge transport properties, and film morphology. The mobility of the side‐chain influences the rate of dedoping, heat of transitions of polymers. The structure regio‐regularity, stability of polarons/bipolarons, film morphologies, and interchain interactions determine the optical and electric properties of polyalkylthiophenes. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1763–1772, 1999     

Ionic conducting membranes based on new sulfonated poly(arylene ether ketone)s for fuel cell applications

The synthesis and characterization of new di‐ and tetra‐sulfonated ether diketone monomers are described. From these monomers, a wide series of sulfonated poly(arylene ether ketone)s (SPAEK) are synthesized by varying the sulfonic acid repartition along the polymer backbones. Their chemical structures are thoroughly characterized by NMR. From these polymers tough membranes are obtained from solution casting method and their water uptake, ionic conductivity, and water/gas permeation properties are determined and compared with those of Nafion membrane. Preliminary fuel cell tests show that SPAEK membranes are promising candidates for fuel cell application. This work brings new insights concerning the beneficial effects of introducing densely sulfonated monomers in a polyarylether macromolecular structure along with fluorinated groups improving conductivity while reducing unwanted excessive swelling. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 771–777     

Copolymers of ethylene and sulfonated norbornene for proton exchange membranes

Terpolymers of ethylene, norbornene, and 5‐exo norbornene methyl alcohol are prepared using Pd phosphine sulfonates as catalysts. The pendant hydroxyl groups are then transformed into thioacetate groups. Films cast from the resulting polymers are then oxidized by hydrogen peroxide. This green oxidation method is found to quantitatively transform thioacetate groups into sulfonic acids, leading to the formation of sulfonated hydrocarbon ionomers. These ionomers are thermally stable, exhibit increasing conductivity up to 110 °C, and have a low water uptake, indicating that these materials are potentially interesting candidates for the preparation of fuel cell membranes. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2669–2676     

Ion transport properties of mechanically stable symmetric ABCBA pentablock copolymers with quaternary ammonium functionalized midblock

Anion exchange membranes (AEMs) are a promising class of materials for applications that require selective ion transport, such as fuel cells, water purification, and electrolysis devices. Studies of structure–morphology–property relationships of ion‐exchange membranes revealed that block copolymers exhibit improved ion conductivity and mechanical properties due to their microphase‐separated morphologies with well‐defined ionic domains. While most studies focused on symmetric diblock or triblock copolymers, here, the first example of a midblock quaternized pentablock AEM is presented. A symmetric ABCBA pentablock copolymer was functionalized to obtain a midblock brominated polymer. Solution cast films were then quaternized to obtain AEMs with resulting ion exchange capacities (IEC) ranging from 0.4 to 0.9 mmol/g. Despite the relatively low IEC, the polymers were highly conductive (up to 60 mS/cm Br^? at 90 °C and 95%RH) with low water absorption (<25 wt %) and maintained adequate mechanical properties in both dry and hydrated conditions. X‐ray scattering and transmission electron microscopy (TEM) revealed formation of cylindrical non‐ionic domains in a connected ionic phase. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 612–622     

Permeation of nitrogen and water vapor through sulfonated polyetherethersulfone membrane

The novel polyetherethersulfone (PES-C) prepared from phenol-phthalein in our institute is an amorphous, rigid, tough material with good mechanical properties over a wide temperature range. To improve its water vapor permeability for the application of gas drying, the PES-C was sulfonated with concentrated sulfuric acid and transferred in sodium, cupric, and ferric salt forms. The sulfonation degree can be regulated by controlling the temperature and reaction time. Characterization of sulfonated PES-C in sodium form was made by IR. Some properties of the sulfonated PES-C, such as solubility, glass transition temperature, thermal stability, mechanical properties, and transport properties to nitrogen and water vapor have also been discussed. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2133–2140, 1997     

Locally sulfonated poly(ether sulfone)s with highly sulfonated units as proton exchange membrane

Novel locally sulfonated poly(ether sulfone)s with highly sulfonated units were successfully synthesized for fuel cell applications. Poly(ether sulfone)s were prepared by the nucleophilic substitution of bis(4‐fluorophenyl) sulfone with 1,2,4,5‐tetrakis([1,1′‐biphenyl]‐2‐oxy)‐3,6‐bis(4‐hydroxyphenoxy)benzene and bis(4‐hydroxyphenyl) sulfide, followed by oxidation using m‐chloroperoxybenzoic acid. The desired highly sulfonated units were easily introduced by postsulfonation and each one had ten sulfonic acid groups. The sulfonated polymers gave tough, flexible, and transparent membranes by solvent casting. The high contrast in polarity between highly sulfonated units and hydrophobic poly(ether sulfone) units enabled the formation of defined phase‐separated structures and well‐connected proton paths. The sulfonated polymers exhibited excellent proton conductivity over a wide range of relative humidities. The proton conductivity of the sulfonated polymer with an ion exchange capacity value of 2.38 mequiv/g was comparable to that of Nafion 117 even at 30% relative humidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3444–3453, 2009     

On the morphology of polymer-based photovoltaics

We review the morphologies of polymer-based solar cells and the parameters that govern the evolution of the morphologies and describe different approaches to achieve the optimum morphology for a BHJ OPV. While there are some distinct differences, there are also some commonalities. It is evident that morphology and the control of the morphology are important for device performance and, by controlling the thermodynamics, in particular, the interactions of the components, and by controlling kinetic parameters, like the rate of solvent evaporation, crystallization and phase separation, optimized morphologies for a given system can be achieved. While much research has focused on P3HT, it is evident that a clearer understanding of the morphology and the evolution of the morphology in low bad gap polymer systems will increase the efficiency further. While current OPVs are on the verge of breaking the 10% barrier, manipulating and controlling the morphology will still be key for device optimization and, equally important, for the fabrication of these devices in an industrial setting. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Tuning the performance of aqueous photovoltaic elastomer gels by solvent polarity and nanostructure development

In this study, a sulfonated pentablock ionomer is considered for use as an aqueous gel electrolyte in photovoltaic elastomer gels (PVEGs) containing photosensitive dyes. Depending on the casting solvent employed, these materials order into different nanoscale morphologies, some of which inherently consist of a continuous pathway through which ions and other polar species are able to diffuse, while others transform into continuous channels upon exposure to water. Here, we examine the effect of solvent polarity during film casting, vapor annealing, and liquid immersion on block ionomer morphology and PVEG photovoltaic performance. Casting the block ionomers from a mixed nonpolar/polar solvent promotes the formation of dispersed ion‐rich spherical microdomains. Alternatively, the use of a single polar solvent produces coexisting nonpolar cylinders and lamellae. Exposure of either morphology to polar solvent vapor causes the block ionomers to restructure into a lamellar morphology, whereas exposure of dispersed ion‐rich microdomains to water induces a transformation to an irregular morphology composed of continuous ionic channels, which provide an effective pathway for ion diffusion and, consequently, the highest photovoltaic efficiency. In addition to their photovoltaic efficacy, these aqueous gels possess improved mechanical properties (in terms of tensile strength and elastic modulus) in the presence of photosensitive dyes. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 85–95     

The Polymer Physics of Multiscale Charge Transport in Conjugated Systems

Conjugated polymers are promising candidates for next‐generation low‐cost flexible electronics. Field‐effect transistors comprising conjugated polymers have witnessed significant improvements in device performance, notably the field‐effect mobility, in the last three decades. However, to truly make these materials commercially competitive, a better understanding of charge‐transport mechanisms in these structurally heterogeneous systems is needed for providing systematic guides for further improvements. This review assesses the key microstructural features of conjugated polymers across multiple length scales that can influence charge transport, with special attention given to the underlying polymer physics. The mechanistic understanding from collective experimental and theoretical studies point to the importance of interconnected ordered domains given the macromolecular nature of the polymeric semiconductors. Based on the criterion, optimization to improve charge transport can be broadly characterized by efforts to (a) promote intrachain transport, (b) establish intercrystallite connectivity, and (c) enhance interchain coupling. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1559–1571     

Strategies for controlling the active layer morphologies in OPVs

This review focuses on the recent developments in our understanding of active layer morphologies for organic photovoltaic cells and approaches to obtain active layer morphologies for high power conversion efficiencies. The evolution of active layer morphologies, as studied by high resolution electron microscopy, X-ray and neutron scattering, and dynamic secondary ion mass spectrometry, is covered, along with strategies including the use of small molecule additives, polymer nanowires and polymer nanoparticles to realize active layer morphologies. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Roles of rhenium diimine complexes as metal‐ion probes and photosensitizers in functional polyurethanes

Polyurethanes incorporated with rhenium diimine complexes were synthesized. The polymers exhibited interesting morphologies and solution properties. Results from gel permeation chromatography suggested the formation of polymer aggregates in solutions. The polymers could act as probes for metal ions. The addition of metal ions to polymer solutions led to significant changes in the electronic absorption properties of the polymer solutions. This was attributed to the interactions between the polyether moieties and metal ions. The metal complexes could also act as efficient photosensitizers. After doping with charge‐transport viologens, the photoconductivity of the polymers was greatly enhanced. The experimental quantum efficiency was simulated with Onsager's theory. The thermalization distances and the primary yields were typically 12–14 Å and 10^?3, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1708–1715, 2003