Water Content of Hydrated Polymer Brushes Measured by an In Situ Combination of a Quartz Crystal Microbalance with Dissipation Monitoring and Spectroscopic Ellipsometry

Poly(methacryloyloxy ethyltrimethylammonium chloride) (PMETAC), poly(sulfopropylmethacrylate potassium salt), or poly(N‐isopropyl acrylamide) (PNIPAM) brushes are synthesized by means of the atom transfer radical polymerization technique from gold surfaces coated with a monolayer of the initiator ω‐mercaptoundecyl bromo isobutyrate. The brush growth is followed in situ and in real time by the combination of quartz crystal microbalance with dissipation technique (QCM‐D) and spectroscopic ellipsometry in a single device. The combination of QCM‐D and ellipsometry allows for the simultaneous determination of both the acoustic mass, m_acous, comprising the mass of the polymer and the solvent, and the optical mass, m_opt, which corresponds to the polymer mass alone. Brush hydration is calculated from the difference between the values obtained for m_acous and m_opt for each polymer synthesized. Brush hydration is then used to quantify the percentage of water released in the brush during collapse; a 30–40% release of water for PMETAC and PSPM brushes in 1 M NaCl and 80% for PNIPAM brushes when the temperature is increased to values above the lower critical solution temperature is observed.     

Explanation for the apparent absence of collapse of polyelectrolyte brushes in the presence of bulky ions

The conformational behavior of poly[2-(methacryloyloxy)ethyltrimethylammonium chloride] (PMETAC) brushes with different chain density in the presence of large benzyltributylammonium chloride (BTBAC) ions has been studied by a Quartz Crystal Microbalance with Dissipation (QCM-D) and Scanning Force Microscopy. Dense brushes do not collapse in the presence of BTBAC solutions of increasing ionic strength, contrary to what is observed in the presence of NaCl. Brush collapse can be observed for low-ionic-strength solutions of BTBAC when the brush density has been reduced. These phenomena can be explained by considering the Hofmeister series as well as ion size and free space in the brush.     

Reversible electrochemical switching of polyelectrolyte brush surface energy using electroactive counterions

Polyelectrolyte brushes with electroactive counterions provide an effective platform for surfaces with electrochemically switchable wetting properties. Polycationic poly(2-(methacryloyloxy)-ethyl-trimethyl-ammonium chloride) (PMETAC) brushes with ferricyanide ions ([Fe(CN)6] 3-) were used as the electrochemically addressable surface. After a negative potential of -0.5 V was applied to the [Fe(CN)6](3-)-coordinated PMETAC brushes, the [Fe(CN)6](3-) species were reduced to [Fe(CN)6](4-), and the surface became more hydrophilic. By application of alternating negative and positive potentials, PMETAC brushes were switched reversibly between the reduced state ([Fe(CN)6]4-) and oxidized state ([Fe(CN)6]3-), resulting in reversible changes in water contact angles. The time required for a complete contact angle change can be tuned from 1 to 20 s, by changing the brush thickness and the concentration of supporting electrolyte. We present an electrochemical brush transport model that includes the electrochemical reaction at the charged electrode and describes ion transport through the brush phase covering the electrode. The model quantitatively describes the response of the contact angle (hydrophilicity) to the applied voltage as a function of background ionic strength and brush thickness, supporting the proposed mechanism of ion transport through the brush and electrochemical reaction at the electrode. A typical diffusion constant for ferricyanide in a PMETAC brush of any thickness in 5 mM KCl supporting electrolyte was found to be 2 x 10(-15) m2 s(-1), 5 to 6 orders of magnitude smaller than its bulk solution value.     

Unusual collapse of highly hydrated polyelectrolyte multilayers with the ionic strength

Highly hydrated polyelectrolyte multilayers (PEMs) were fabricated by “layer by layer” (LBL) assembly of poly (diallyl dimethyl ammonium chloride) (PDADMAC) and poly (sodium 4‐styrene sulfonate) (PSS) in 0.5 M NaCl. Both thickness and hydration of the film were determined in situ as the multilayer was assembled by means of the quartz crystal microbalance with dissipation (QCM‐D) and the Spectroscopic Ellipsometry techniques combined in a single device. For PEMs of 17 total layers in water, a final thickness of up to 300 nm and a hydration of 69% were measured. The response towards the ionic strength was then studied by means of QCM‐D. PEMs of 17 layers, with PDADMAC as last layer, shrunk dramatically and lost water when exposed to aqueous NaCl solutions of increasing concentration. Indeed, a thickness variation up to 100 nm and reduction in the 50% of the water content were observed when the PEM was exposed to 1 M NaCl. On the contrary, PEMs where PSS appears on top showed no measurable change upon the variation in the ionic strength. This brings the possibility to control the responsive character of the PEMs simply by selecting the last polyelectrolyte layer (PDADMAC or PSS) deposited. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Comparison of the growth and degradation of poly(glycolic acid) and poly(ε‐caprolactone) brushes

The growth and degradation of poly(glycolic acid) (PGA) and poly(ε‐caprolactone) (PCL) brushes were compared. Using tin (octanoate) as the catalyst, optimal conditions were found for growth of each polyester brush from the hydroxy‐terminated silicon surface via ring‐opening polymerization. PCL brushes grew thicker at elevated temperatures but the thickest PGA brushes grew at room temperature. Unlike bulk polyesters that can degrade under both acidic and basic conditions, the confined surface polyester brushes only degraded under neutral or basic conditions. The degradation mechanism of grafted polyester brushes was probed through a blocking test. It was shown that the terminal hydroxy groups of these polyester brushes were essential to the degradation process indicating a preferential backbiting mechanism. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4643–4649     

RAFT‐mediated synthesis and temperature‐induced responsive properties of poly(2‐(2‐methoxyethoxy)ethyl methacrylate) brushes

Well‐defined, high‐density poly(2‐(2‐methoxyethoxy)ethyl methacrylate) [poly(MEO₂MA)] brushes were fabricated through a reliable strategy by the combination of self‐assembly of a monolayer of 3‐aminopropyltrimethoxy silane on silicon surface to immobilize 4‐cyano‐4‐(dodecylsulfanylthiocarbonyl)sulfanyl pentanoic acid chain transfer agent and reversible addition‐fragmentation chain transfer‐mediated polymerization of MEO₂MA. The whole fabrication process of the poly(MEO₂MA) brushes was followed by water contact angle, grazing angle‐Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and atomic force microscopy. Characterization of the poly(MEO₂MA) brushes, such as molecular weight and thickness determination, were measured by gel permeation chromatography and ellipsometry, and the grafting density was estimated. The temperature‐responsive property of the poly(MEO₂MA) brushes was further investigated and the result verified the brush‐to‐mushroom phase transition of the poly(MEO₂MA) chains from low to high temperature. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Electrochemical characteristics of polyelectrolyte brushes with electroactive counterions

Cyclic voltammetry (CV) was employed to characterize the electrochemical behavior of polyelectrolyte brushes with immobilized electroactive counterions in response to external changes in concentration and composition of the supporting electrolyte and as a function of brush thickness. Poly(methacryloyloxy)ethyl-trimethyl-ammonium chloride (PMETAC) brushes were synthesized on Au substrates via atom transfer radical polymerization followed by ion-exchange with ferricyanide ions ([Fe(CN)6]3-) as redox probes. CV measurements of the modified PMETAC brushes showed the typical electrochemical response corresponding to a surface-confined electroactive species and the redox counterions, as [Fe(CN)6]3- species form stable ion pairs with the quaternary ammonium groups of the brush. The electron-transfer features of PMETAC brushes with different thicknesses, as characterized by CV and UV-vis spectroscopy, revealed that the charge density probed by CV was lower than the charge density measured by UV-vis spectroscopy. The electrode current decreased significantly with increasing concentration of supporting electrolyte due to the effect of the Donnan potential. Hydrophobic counterions, ClO4-, which induced brush collapse, lead to significantly reduced electrode currents.     

Structure and Surface Properties of High-density Polyelectrolyte Brushes at the Interface of Aqueous Solution

Zwitterionic and cationic polyelectrolyte brushes were prepared by surface-initiated atom transfer radical polymerization of 2-methacryloyloxy- ethyl phosphorylcholine (MPC) and 2-(N,N-dimethylamino)ethyl methacrylate (DMAEMA), respectively. The poly(DMAEMA) brush was treated with methyl iodide to form poly[2-(methacryloyloxy) ethyltrimethylammonium iodide] [poly(METAI)]. The effects of ionic strength on brush structure and surface properties of densely grafted polyelectrolyte brushes were analyzed by contact angle measurements, neutron reflectivity (NR) and macroscopic friction tests. Both polyelectrolyte brushes exhibited hydrophilic properties. The contact angle of the poly(MPC) brush surface against water was ca. 0° in air and the contact angle of the air bubble in water was ca. 170°. The air bubble in water hardly attached to the poly(MPC) brush surface, indicating super hydrophilic characteristics. NR measurements of poly(MPC) and poly(METAI) brushes showed that the grafted polymer chains were extended from the substrate surface in a good solvent such as water. Interestingly, NR study did not reveal the shrinkage of the brush chain in salt solution. The polyelectrolyte brushes immersed in both water and NaCl solution at various concentrations showed a low friction coefficient and low adhesion force.     

Synthesis of amphiphilic copolymer brushes: Poly(ethylene oxide)‐graft‐polystyrene

A well‐defined amphiphilic copolymer brush with poly(ethylene oxide) as the main chain and polystyrene as the side chain was successfully prepared by a combination of anionic polymerization and atom transfer radical polymerization (ATRP). The glycidol was first protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether and then copolymerized with ethylene oxide by the initiation of a mixture of diphenylmethylpotassium and triethylene glycol to give the well‐defined polymer poly(ethylene oxide‐co‐2,3‐epoxypropyl‐1‐ethoxyethyl ether); the latter was hydrolyzed under acidic conditions, and then the recovered copolymer of ethylene oxide and glycidol {poly(ethylene oxide‐co‐glycidol) [poly(EO‐co‐Gly)]} with multiple pending hydroxymethyl groups was esterified with 2‐bromoisobutyryl bromide to produce the macro‐ATRP initiator [poly(EO‐co‐Gly)_(ATRP). The latter was used to initiate the polymerization of styrene to form the amphiphilic copolymer brushes. The object products and intermediates were characterized with ¹H NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, Fourier transform infrared, and size exclusion chromatography in detail. In all cases, the molecular weight distribution of the copolymer brushes was rather narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), and the linear dependence of ln[M₀]/[M] (where [M₀] is the initial monomer concentration and [M] is the monomer concentration at a certain time) on time demonstrated that the styrene polymerization was well controlled. This method has universal significance for the preparation of copolymer brushes with hydrophilic poly(ethylene oxide) as the main chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4361–4371, 2006     

Continuously Variable Regulation of the Speed of Bubble‐Propelled Janus Microcapsule Motors Based on Salt‐Responsive Polyelectrolyte Brushes

The engineering of self‐propelled micro‐/nanomotors (MNMs) with continuously variable speeds, akin to macroscopic automobiles equipped with a continuously variable transmission, is still a huge challenge. Herein, after grafting with salt‐responsive poly[2‐(methacryloyloxy)ethyltrimethylammonium chloride] (PMETAC) brushes, bubble‐propelled Janus microcapsule motors with polyelectrolyte multilayers exhibited adjustable speeds when the type and concentration of the counterion was changed. Reversible switching between low‐ and high‐speed states was achieved by modulating the PMETAC brushes between hydrophobic and hydrophilic configurations by ion exchange with ClO₄^? and polyphosphate anions. This continuously variable regulation enabled control of the speed in an accurate and predictable manner and an autonomous response to the local chemical environment. This study suggests that the integration of polymer brushes with precisely adjustable responsiveness offers a promising route for motion control of smart MNMs that act like their counterparts in living systems.     

Tribological properties of hydrophilic polymer brushes under wet conditions

This article demonstrates a water‐lubrication system using high‐density hydrophilic polymer brushes consisting of 2,3‐dehydroxypropyl methacrylate (DHMA), vinyl alcohol, oligo(ethylene glycol)methyl ether methacrylate, 2‐(methacryloyloxy)ethyltrimethylammonium chloride (MTAC), 3‐sulfopropyl methacrylate potassium salt (SPMK), and 2‐methacryloyloxyethyl phosphorylcholine (MPC) prepared by surface‐initiated controlled radical polymerization. Macroscopic frictional properties of brush surfaces were characterized by sliding a glass ball probe in water using a ball‐on‐plate type tribotester under the load of 0.1–0.49 N at the sliding velocity of 10^?5–10^?1 m s^?1 at 298 K. A poly(DHMA) brush showed a relatively larger friction coefficient in water, whereas the polyelectrolyte brushes, such as poly(SPMK) and poly(MPC), revealed significantly low friction coefficients below 0.02 in water and in humid air conditions. A drastic reduction in the friction coefficient of polyelectrolyte brushes in aqueous solution was observed at around 10^?3–10^?2 m s^?1 owing to the hydrodynamic lubrication effect, however, an increase in salt concentration in the aqueous solution led to the increase in the friction coefficients of poly(MTAC) and poly(SPMK) brushes. The poly(SPMK) brush showed a stable and low friction coefficient in water even after sliding over 450 friction cycles, indicating a good wear resistance of the brush film. © 2010 The Japan Chemical Journal Forum and Wiley Periodicals, Inc. Chem Rec 10: 208–216; 2010: Published online in Wiley InterScience ( www.interscience.wiley.com ) DOI 10.1002/tcr.201000001     

Facile Fabrication of Bio- and Dual-Functional Poly(2-oxazoline) Bottle-Brush Brush Surfaces

Poly(2-oxazoline)s (POx) bottle-brush brushes have excellent biocompatible and lubricious properties, which are promising for the functionalization of surfaces for biomedical devices. Herein, a facile synthesis of POx is reported which is based bottle-brush brushes (BBBs) on solid substrates. Initially, backbone brushes of poly(2-isopropenyl-2-oxazoline) (PIPOx) were fabricated via surface initiated Cu⁰ plate-mediated controlled radical polymerization (SI-Cu⁰CRP). Poly(2-methyl-2-oxazoline) (PMeOx) side chains were subsequently grafted from the PIPOx backbone via living cationic ring opening polymerization (LCROP), which result in ≈100 % increase in brush thickness (from 58 to 110 nm). The resultant BBBs shows tunable thickness up to 300 nm and high grafting density (σ) with 0.42 chains nm⁻². The synthetic procedure of POx BBBs can be further simplified by using SI-Cu⁰CRP with POx molecular brush as macromonomer (M_n=536 g mol⁻¹, PDI=1.10), which results in BBBs surface up to 60 nm with well-defined molecular structure. Both procedures are significantly superior to the state-of-art approaches for the synthesis of POx BBBs, which are promising to design bio-functional surfaces.     

Understanding anion transport in an aminated trimethyl polyphenylene with high anionic conductivity

An alkaline exchange membrane (AEM) based on an aminated trimethyl poly(phenylene) is studied in detail. This article reports hydroxide ion conductivity through an in situ method that allows for a more accurate measurement. The ionic conductivities of the membrane in bromide and carbonate forms at 90 °C and 95% RH are found to be 13 and 17 mS cm⁻¹ respectively. When exchanged with hydroxide, conductivity improved to 86 mS cm⁻¹ under the same experimental conditions. The effect of relative humidity on water uptake and the SAXS patterns of the AEM membranes were investigated. SAXS analysis revealed a rigid aromatic structure of the AEM membrane with no microphase separation. The synthesized AEM is shown to be mechanically stable as seen from the water uptake and SAXS studies. Diffusion NMR studies demonstrated a steady state long-range diffusion constant, D_∞ of 9.8 × 10⁻⁶ cm² s⁻¹ after 50–100 ms. © 2012 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1743–1750, 2013     

Stimuli‐responsive diblock copolymer brushes via combination of “click chemistry” and living radical polymerization

pH‐ and temperature‐responsive poly(N‐isopropylacrylamide‐block?4‐vinylbenzoic acid) (poly(NIPAAm‐b‐VBA)) diblock copolymer brushes on silicon wafers have been successfully prepared by combining click reaction, single‐electron transfer‐living radical polymerization (SET‐LRP), and reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. Azide‐terminated poly(NIPAAm) brushes were obtained by SET‐LRP followed by reaction with sodium azide. A click reaction was utilized to exchange the azide end group of a poly(NIPAAm) brushes to form a surface‐immobilized macro‐RAFT agent, which was successfully chain extended via RAFT polymerization to produce poly(NIPAAm‐b‐VBA) brushes. The addition of sacrificial initiator and/or chain‐transfer agent permitted the formation of well‐defined diblock copolymer brushes and free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. Ellipsometry, contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy were used to characterize the immobilization of initiator on the silicon wafer, poly(NIPAAm) brush formation via SET‐LRP, click reaction, and poly(NIPAAm‐b‐VBA) brush formation via RAFT polymerization. The poly(NIPAAm‐b‐VBA) brushes demonstrate stimuli‐responsive behavior with respect to pH and temperature. The swollen brush thickness of poly(NIPAAm‐b‐VBA) brush increases with increasing pH, and decreases with increasing temperature. These results can provide guidance for the design of smart materials based on copolymer brushes. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2677–2685     

Synthesis and characterization of perfluoro quaternary ammonium anion exchange membranes

In this study, new alkaline exchange membranes were prepared from the perfluorinated 3M ionomer with various quaternary ammonium cations attached with sulfonamide linkage. The degree of functionalization varied depending on the cation species, resulting in different ion exchange capacities (IECs), 0.33–0.72 meq g⁻¹. There was evidence of polymer degradation when the films were exposed to hydroxide, and hence all membrane characterization was performed in the chloride form. Conductivity was dependent on cation species and IEC, E_a = 36–59 kJ mol⁻¹. Diffusion of water through the membrane was relatively high 1.6 × 10⁻⁵ cm² s⁻¹ and indicated restriction over a range of diffusion times, 6–700 ms. Water uptake (WU) in the membranes was generally low and the hydration level varied based on cation species, λ = 6–11. Small-angle scattering experiments suggested ionic aggregation, 37–42 Å, independent of cation species but slight differences in long-range order with cation species. © 2012 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1761–1769, 2013     

Controlled synthesis of hydrophilic concentrated polymer brushes and their friction/lubrication properties in aqueous solutions

Polymer brushes of water‐soluble polymers, poly(2‐hydroxyethyl acrylate) (PHEA) and poly(poly(oxyethyleneglycol)methylether acrylate) (PPEGA), were synthesized on a silicon wafer and a silica particle by applying photo‐induced organotellurium‐mediated radical polymerization to surface‐initiated graft polymerization. High graft densities were obtained, corresponding to reduced graft densities of about 0.32 and 0.42 for the PHEA and PPEGA brushes, respectively. These values were high enough to be categorized in the regime of “concentrated” polymer brushes (CPBs). Atomic force microscopic (AFM) study revealed that the CPB of PPEGA was allowed to be highly swollen in water but the CPB of PHEA did not. This means that water is reasonably good for PPEGA but not for PHEA. The AFM microtribological study between swollen brushes revealed two lubrication regimes, namely, boundary‐ and hydrodynamic‐lubrication regimes, with different shear‐velocity dependencies. Reflecting insufficient quality of water as a solvent, the CPB of PHEA showed adhesive interaction and thereby a higher frictional coefficient μ in the boundary lubrication. More interestingly, super lubrication was achieved for the CPB of PPEGA with a μ value in the order of 10^?4 in water and in 0.1 M aqueous NaCl solution (without the help of electrostatic repulsion). Super lubrication was concluded to be a characteristic feature of the CPB, even in an aqueous system. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Collapse and swelling of poly(N‐isopropylacrylamide‐co‐sodium acrylate) copolymer brushes grafted on a flat SiO2 surface

Poly(N‐isopropylacrylamide‐co‐sodium acrylate) copolymer brushes grafted on SiO₂‐coated quartz crystal surface were prepared with a surface‐immobilized initiator. The collapse and swelling of the thermally sensitive copolymer brushes in water were studied with quartz crystal microbalance in situ. The frequency and dissipation changes with the temperature increasing in the range 20–38 °C indicate that the brushes undergo a continuous collapse transition. Our results show that the copolymer brushes collapse to a state where the brushes were prepared. A hysteresis was observed in the cooling process. Fourier transform infrared (FTIR) results revealed that the formation of some additional hydrogen bonds within the copolymer chains at their collapsed state is responsible for the hysteresis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 770–778, 2006     

Thermoresponsive Polymer Brush Modulation on the Direction of Motion of Phoretically Driven Janus Micromotors

We report a thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) brush functionalized Janus Au–Pt bimetallic micromotor capable of modulating the direction of motion with the change of the ambient temperature. The PNIPAM@Au–Pt micromotor moved along the Au–Pt direction with a speed of 8.5 μm s^?1 in 1.5 % H₂O₂ at 25 °C (below the lower critical solution temperature (LCST) of PNIPAM), whereas it changed the direction of motion (i.e., along the Pt–Au direction) and the speed decreased to 2.3 μm s^?1 at 35 °C (above LCST). Below LCST, PNIPAM brushes grafted on the Au side were hydrophilic and swelled, which permitted the electron transfer and proton diffusion on the Au side, and thus the motion is regarded as a self‐electrophoretic mechanism. However, PNIPAM brushes above LCST became hydrophobic and collapsed, and thus the driving mechanism switched to the self‐diffusiophoresis like that of Pt‐modified Janus silica motors. These motors could reversibly change the direction of motion with the transition of the hydrophobic and hydrophilic states of the grafted PNIPAM brushes. Such a thermoresponsive polymer brush functionalization method provides a new strategy for engineering the kinematic behavior of phoretically driven micro/nanomotors.     

Polar anchoring strengths of nematic liquid crystal on high-density polymer brush surfaces

ABSTRACT

Herein, the polar anchoring energy coefficient (A_θ) of nematic liquid crystal (NLC) was examined for high-density polymer brushes via capacitance measurements. The A_θ is 10^?4 J m^?2 for the brushes of poly(methyl methacrylate), poly(ethyl methacrylate) and poly(styrene). The value decreases to 10^?5 J m^?2 for poly(n-butyl methacrylate) and poly(hexyl methacrylate) with lower glass transition temperatures. However, each polymer brush displays a constant A_θ value over a temperature range of ?15°C to 90°C, which is hardly affected by the graft density and brush thickness. At 25°C, A_θ is 10 times greater than the corresponding azimuthal anchoring energy coefficient (A_φ); therefore, NLCs on polymer brushes can be preferentially aligned along the in-plane component of the applied field.     

Elucidation of the mechanism of surface‐initiated atom transfer radical polymerization from a diazonium‐based initiator layer

This study elucidates the influence of the atom transfer radical polymerization initiator structure, monolayer versus disordered multilayer, on the growth kinetics and the structural transition of poly(methyl methacrylate) (PMMA) brush layers. The multilayer initiator film, prepared by acylation of the electrografted 2‐phenylethanol layer using 2‐bromoisobutyryl bromide, consists of ～4.6 times more tert‐butyl bromide groups compared to monolayer initiator prepared by self assembly technique. The results demonstrate the formation of precursor complex between Cu^I catalyst and the bromine initiator as a prerequisite step before the onset of polymerization. Furthermore, the PMMA brushes formed by the polymerization from the multilayered initiator layer at 50 °C are 20‐fold thicker compared to the polymerization at 25 °C due to the swelling of the multilayered initiator film. In contrast, the thickness of the PMMA layer on the monolayer initiator is less affected by the polymerization temperature. By varying the initiator density on the surface, the solvent content in the PMMA layer is shown to vary from 15% to 94%, resulting in the transition from concentrated over semidiluted to diluted brushes. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012