Effect of nature and extent of crosslinking on swelling and mechanical behavior of styrene–butadiene rubber membranes

The influence of crosslink type and crosslink density on the swelling and mechanical behavior of styrene–butadiene rubber (SBR) membranes were studied in four aliphatic hydrocarbons. To vary the crosslink type and crosslink density, SBR was vulcanized by four different vulcanizing systems viz conventional, efficient, peroxide and a mixture of sulfur and peroxide. SBR vulcanizates having mono or disulfidic crosslinks (efficient system) exhibited the highest solvent uptake whereas those with C–C bonds (peroxide system) showed the lowest. SBR crosslinked by the mixed system showed superior mechanical properties in the unswollen, swollen and deswollen conditions. Arrhenius and thermodynamic parameters were evaluated from the diffusion data. Finally, a comparison between theoretical and experimental diffusion results was carried out.     

Stabilization effect of potential antioxidants on the thermooxidative stability of styrene–butadiene rubber

Effects of several heterocyclic compounds containing nitrogen, trisubstituted amines and diamines and molecules based on N,N,N′,N′,N′′,N′′-substituted-[1,3,5]triazine-2,4,6-triamine in preventing thermooxidative degradation of styrene–butadiene rubber (SBR) have been studied using non-isothermal DSC measurements. The aim of this study was to determine and compare the stabilizing effect of individual compounds and to select the structures with the best antioxidative properties. In order to compare the stabilizing effect of the compounds, induction periods and protection factors have been calculated. The treatment of the experimental data was carried out using a method based on a non-Arrhenian temperature function. The results show that better antioxidative properties can be assigned to heterocyclic compounds. On the other hand, molecules containing triazine structures exhibited only negligible stabilizing effect on SBR at lower temperatures and even destabilizing effect at higher temperatures.     

The effect of chlorosulphonated polyethylene on thermal properties and combustibility of butadiene–styrene rubber

This article describes the test results of thermal properties and flammability of the unconventionally cross-linked blends of chlorosulfonated polyethylene (CSM) and butadiene–styrene rubber (SBR) by means of zinc oxide or nano-zinc oxide. The thermal curves have been interpreted from the point of view of the chemical transitions of elastomers and their blends. It has been found that the content of combined chlorine in CSM exerts a significant influence on the cross-linking kinetics of CSM/SBR blends, their thermal properties and flammability.     

Thermal stability and flammability of butadiene–styrene rubber nanocomposites

Heterobimetallic oxalato complex precursors, manganese(II)tetraaquatris(oxalato)lanthanate(III)hexahydrate (MnOLa), cobalt(II)pentaaquatris(oxalato)lanthanate(III)trihydrate (CoOLa), nickel(II)pentaaquatris(oxalato)lanthanate(III)hexahydrate (NiOLa) and copper(II)diaaquatris(oxalato)lanthanate(III)monohydrate (CuOLa) of the type, M₃[La(C₂O₄)₃(H₂O) _m ]₂·nH₂O have been synthesized in aqueous medium. The precursors were characterized by elemental analysis, IR, electronic spectral and powder X-ray diffraction studies. The good crystalline nature with monoclinic structures predominates in MnOLa and NiOLa whereas triclinic structures were found in CoOLa and CuOLa. The solid-state thermal behaviour of the precursors was explored using TG, DTG and DTA in air. The MnOLa generated a mixture species consisting mainly of MnO₂, Mn₃O₄, Mn₅O₈, La₂O₃ and LaMn₇O₁₂ at 1000 °C through the formation of several intermediate species at 380 and 570 °C. The studies revealed that CoOLa led mainly to LaCoO₃ and La₂CoO₄ along with some oxides of both the cobalt and lanthanum at 1000 °C. In case of nickel analogue the mixture species identified at 1000 °C are mainly of La₂NiO₄, La₂O₃, Ni₂O₃ and NiO_2. In case of CuOLa the product at 1000 °C consisted of La₂CuO₄, La₂Cu₂O₅ and oxides of copper and lanthanum. The nature of decomposition of the precursors in nitrogen were seen from DSC study and the kinetic parameters i.e., E ^* , lnk ₀, ΔH ^# , ΔS ^# and order of reaction of all the steps were evaluated and discussed.     

Effect of graphite and common rubber plasticizers on properties and performance of ceramizable styrene–butadiene rubber-based composites

Journal of Thermal Analysis and Calorimetry - Ceramizable composites are highly filled polymer dispersion composites which create stiff porous and durable ceramic structure when exposed to fire or...     

Effect of sol–gel derived in situ silica on the morphology and mechanical behavior of natural rubber and acrylonitrile butadiene rubber blends

Silica particles were generated and grown in situ by sol–gel method into rubber blends comprised of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) at various blend ratios. Silica formed into rubber matrix was amorphous in nature. Amount of in situ silica increased with increase in natural rubber proportion in the blends during the sol–gel process. Morphology studies showed that the generated in situ silica were nanoparticles of different shapes and sizes mostly grown into the NR phase of the blends. In situ silica filled NR/NBR blend composites showed improvement in the mechanical and dynamic mechanical behaviors in comparison to those of the unfilled and externally filled NR/NBR blend composites. For the NR/NBR blend at 40/60 composition, in particular, the improvement was appreciable where size and dispersion of the silica particles into the rubber matrix were found to be more uniform. Dynamic mechanical analysis revealed a strong rubber–in situ silica interaction as indicated by a positive shift of the glass transition temperature of both the rubber phases in the blends.     

Thermal stability and flammability of styrene–butadiene rubber (SBR) composites

The article presents the effect of attapulgite (ATT) and its synergic action with carbon or silica on the thermal properties and flammability of cross-linked styrene–butadiene rubber. It has been shown that ATT is active filler improving the thermal and mechanical properties of composites containing this aluminosilicate. The decreased flammability of vulcanizates containing ATT compared to that of unfilled vulcanizates results from good insulating properties of the ATT used. The considerable reduction in the flammability of composites containing ATT and carbon nanofiber or silica is connected, first of all, with the formation of a homogeneous boundary layer.     

Thermal characterization of the effect of fillers and ionic liquids on the vulcanization and properties of acrylonitrile–butadiene elastomer

Different thermal analysis techniques were used to study the effect of fillers and ionic liquids (ILs) on the vulcanization process, thermal and dynamic mechanical properties of acrylonitrile–butadiene elastomer (NBR). The products of the studies were composites of NBR filled with hydrotalcite, nanosized silica or carbon black. ILs such as 1-butyl-1-methylpyrrolidinium (BMpyrrolBF₄), 1-butyl-4-methylpyridinium (BMpyrBF₄) or 1-butyl-1-methylpiperidinium (BMpipBF₄) tetrafluoroborates were applied to improve the dispersion degree of the curatives and filler particles in the elastomer and to increase the efficiency of vulcanization. The differential scanning calorimetry results indicated that ILs reduced the vulcanization temperature of NBR compounds and increased the homogeneity of cross-link distribution in the elastomer network. NBRs filled with carbon black or silica exhibited similar thermal stabilities, whereas hydrotalcite reduced the temperature of thermal decomposition. The lowest mechanical loss factors were determined for vulcanizates filled with nanosized silica.

     

The effect of activated fillers on the properties of styrene–acrylic adhesives

Results of kaolin modification by thermal activation, sonication and 3% solution of acetic acid are considered. It is shown that the introduction of thermally activated kaolin to compositions based on styrene–acrylic filming agents increases the adhesion characteristics by 1.25–1.4 times (for steel and cement–sand surfaces) and cohesive strength by 1.5–2 times.     

Coagulating effect of N,N-dimethyl-N,N-diallylammonium chloride in recovery of butadiene—styrene rubber from latex

The effect of additions of an organic cationic electrolyte, N,N-dimethyl-N,N-diallylammonium chloride, on the threshold of rapid coagulation, duration of the first coagulation step, and values of the 1-min and maximal turbidity was examined. The coagulating performance of additives in recovery of rubber from SKS-30 ARK butadiene—styrene latex was studied in relation to the concentrations of the dispersed phase and sulfuric acid and to temperature.     

Effect of a novel charring agent on thermal degradation and flame retardancy of acrylonitrile–butadiene–styrene

A novel charring agent poly(p-propane terephthalamide) (PPTA) was synthesized by using terephthaloyl chloride and 1,3-propanediamine through solution polycondensation and it was used together with ammonium polyphosphate (APP) to prepare a novel intumescent flame retardant (IFR) for ABS. The thermal degradation behaviour and flame retardancy were investigated, the results showed that PPTA could be effective as a charring agent, the flame retardancy of ABS and the mass of residues improved greatly with the addition of IFR. When the content of APP was 22.5 mass% and PPTA was 7.5 mass%, the limiting oxygen index (LOI) value of IFR-ABS system was found to be 32.4, and class V-0 of UL-94 test was passed. Moreover, the synergistic effects of two different adjuvants AlPi and MnO₂ in IFR-ABS system have been studied.     

Rheological properties of styrene–butadiene rubber filled with electron beam modified surface treated dual phase fillers

The rheological properties of styrene–butadiene rubber (SBR) loaded with dual phase filler were measured using Monsanto Processability Tester (MPT) at three different temperatures (100°C, 110°C and 130°C) and four different shear rates (61.3, 306.3, 613, and 1004.5 s⁻¹). The effect of electron beam modification of dual phase filler in absence and presence of trimethylol propane triacrylate (TMPTA) or triethoxysilylpropyltetrasulphide (Si-69) on melt flow properties of SBR was also studied. The viscosity of all the systems decreases with shear rate indicating their pseudoplastic or shear thinning nature. The higher shear viscosity for the SBR loaded with the electron beam modified filler is explained in terms of variation in structure of the filler upon electron beam irradiation. Die swell of the modified filler loaded SBR is slightly higher than that of the unmodified filler loaded rubber, which is explained by calculating normal stress difference for the systems. Activation energy of the modified filler loaded SBR systems is also slightly higher than that of the control filler loaded SBR system.     

Rheology of linear and branched styrene–acrylonitrile copolymers. Similarities and differences

A comprehensive investigation of rheological properties of linear and branched styrene-acrylonitrile copolymer specimens with similar molecular characteristics has been carried out. During the steady-state shear flow, the viscosity properties of both specimens are described by the Cross equation. In this case, the branched copolymer is characterized by a higher viscosity and shear thinning degree as well as by substantially lower shear rate values corresponding to transition to the non-Newtonian flow region. The elasticity of the branched copolymer melt (estimated from the value of the first normal stress difference) is considerably higher than that of the linear. This is reflected on the characteristics of occurrence of unstable flow at high shear rates. Rougher extrudate surface distortions are characteristic for the branched copolymer, and the shear rate corresponding to their occurrence is noticeably lower than for the linear copolymer. The dynamic characteristics of the copolymers being compared also attest to a greater elasticity of the branched specimen. An investigation of the viscoelastic properties in a wide temperature range allowed constructing a generalized frequency dependence of dynamic moduli encompassing various regions of the relaxation states of the copolymer specimens. Continuous relaxation spectra were calculated by means of the Mellin transform. It is shown that relaxation phenomena caused by segmental mobility doesn’t depend on the presence of branchings, whereas branching of the chain has a substantial effect on translation mobility of the chain as a whole. Branching leads to a noticeable increase of transient elongation viscosity but has almost no effect of strain hardening of the melt.     

A CFD investigation of the effect of non-Newtonian behavior of Cu–water nanofluids on their heat transfer and flow friction characteristics

Journal of Thermal Analysis and Calorimetry - In the present study, a finite volume method is used to investigate heat transfer and flow friction behavior of non-Newtonian nanofluids. To study a...     

A survey on the effect of ionic liquid on electrochemical behavior and electrocatalytic activity of a phosphomolybdic acid-ionic liquid-MWCNT–modified glassy carbon electrode

Journal of Solid State Electrochemistry - The surface of a glassy carbon electrode modified with multi-walled carbon nanotubes (GCE/MWCNTs) was coated with a layer of phosphomolybdic acid (PMo12)...     

Entropy analysis of Powell–Eyring hybrid nanofluid including effect of linear thermal radiation and viscous dissipation

Journal of Thermal Analysis and Calorimetry - Hybrid nanofluids are introduced as heat transfer fluids with greater surface stability, diffusion and dispersion capabilities compared to traditional...     

Emulsion polymerization of styrene using irreversible addition–fragmentation chain transfer agents: effect on the course of the polymerization and molecular weight

The emulsion polymerization of styrene with three different chain transfer agents (CTAs) based on irreversible addition–fragmentation chain transfer (AFCT) mechanism was first reported in this work. The influences of these irreversible AFCT agents on the rate of polymerization, particle size, and molecular weight were investigated. It was found that the intrinsic activity and desorption behaviors of the CTAs determined the efficiency for molecular weight control, rate of polymerization, and particle size in the emulsion polymerization. It has been demonstrated that the rate of polymerization and particle size decreased dramatically in the presence of the irreversible AFCT agents with high chain transfer constant (ethyl α-p-toluenesulfonyl-methacrylate), meanwhile, the molecular weight of the polystyrene could not be controlled well, whereas the irreversible AFCT agents with low chain transfer constant (butyl(2-phenylallyl)sulfane and 2,3-dichloropropene) had a slight effect on the polymerization rate, particle size, and were fairly well for molecular weight control over the whole conversion range in the emulsion polymerization of styrene. The average number of radicals per particle and the number-average molecular weight were calculated by classical radical emulsion polymerization theory, and the experimental results were in good agreement with the results of model calculations, when the irreversible AFCT agents were used as CTAs. The effect of chain transfer agents on the kinetics and nucleation in the emulsion polymerization of styrene can be attributed to desorption of chain-transferred radicals from the polymer particles. The results of this work show that butyl(2-phenylallyl)sulfane as CTA in emulsion polymerization of styrene provides the best balance between the rate of polymerization and the efficiency for molecular weight control conflicting tendencies.