Modulation instability in lossy silicon optical waveguide

Taking into account the small linear loss of silicon-on-insulator(SOI) waveguide, conditions and gain spectra of modulation instability(MI) induced by combined effects of self-phase modulation and waveguide dispersions are investigated. The impacts of various parameters to gain spectra of MI are analyzed theoretically. Results show that strong MI takes place even in the existence of low light power. The MI peak gain is 2 to 3 orders of magnitude larger than that achieved in optical fibers with the same light power. The linear loss of waveguide impacts gain spectra of MI, even within ultra-short propagation distance. The peak gain, peak gain frequency and bandwidth of gain spectra decrease to 66.828%, 41.683% and 41.6879% of their maxima at propagation distance z = 5mm, respectively.     

Brillouin characterization of holey optical fibers

We report the results of detailed measurements on the Brillouin frequency shift (BFS), gain bandwidth, and gain coefficients of several small-core holey optical fibers (HFs) of both uniform and axially varying structural characteristics and compare these with measurements on more conventional fibers. Our measurements show that the BFS of HFs is first-order proportional to the modal index for light propagating along the fiber and is thus extremely sensitive to its precise structural parameters. Our results highlight the possibility of using distributed Brillouin scattering measurements to perform nondestructive structural characterization of HFs, and the possibility of producing Brillouin-suppressed HFs using controlled structural variation along the fiber length.     

微弱光学图像的光参量放大特性的研究

研究了微弱光学图像在光参量图像放大中的放大特性,分析了相位匹配和晶体的空间频率带宽对图像信号增益的影响,从实验上验证了不同的相位匹配时输入图像信号在傅里叶平面上的增益分布.结果表明,当晶体的空间频率带宽大于输入图像信号的空间频率带宽且完全相位匹配时,光参量图像放大器能够对输入图像信号实现无失真、高增益的理想放大;有相位失配时,图像信号的增益峰值向高空间频率范围移动,并且在峰值附近范围变窄,随相位失配量大小的变化能够对图像信号光场中某特定空间频率实现放大,对图像信号进行滤波处理,突出图像特定频率的信息,实现图像边缘增强.     

Explicit finite difference solution of the power flow equation in W-type optical fibers

Using the power flow equation, we have calculated spatial transients of power distribution and a steady-state distribution that are due to coupling of guided to leaky modes in W-type optical fibers (doubly clad fibers). A numerical solution has been obtained by the explicit finite difference method. Results show that power distribution in W-type optical fibers depends on both the intermediate layer width and the coupling strength. W-shaped index profile of optical fibers is effective in reducing modal dispersion and therefore in improving the fiber bandwidth. We have also shown that explicit finite difference method is effective and accurate for solving the power flow equation in W-type optical fibers.     

Parametric Amplification in Four-Layered QPM Leaky Waveguides

Parametric amplification of signal wave in a four-layered leaky waveguide configuration in Z-cut LiNbO 3 , where the pump and signal waves are guided modes and the idler is radiated into the substrate has been studied using coupled mode approach. It is shown that in this configuration, the signal gain can be greatly enhanced as compared to the case of a three-layered QPM Cerenkov-idler configuration. The studies show that by appropriately choosing the waveguide parameters, one can have a trade-off between signal gain bandwidth and the peak signal gain achieved. These studies should find application in designing optical parametric amplifiers and oscillators.     

Analysis and improvement of optical frequency response in a long wavelength transistor laser

Charge control model and rate equations have been exploited for the first time in order to glean the optical frequency response of a long-wavelength heterojunction bipolar transistor laser. For a 1.56 μm N-InP/p-InAlGaAs/N-InP fabricated transistor laser with a single quantum well, the optical bandwidth is estimated using this model. All parameters of the mentioned model have been computed for this new type of long wavelength transistor laser. It has been found that frequency response of this optoelectronic device has a 29 dB resonance peak which is not very desirable and is so higher than traditional GaAs transistor lasers. Furthermore, we have illustrated that the resonance peak will decrease and the optical bandwidth will increase, if we increase the width of the quantum well. Finally, we have analyzed that how base width affects on the optical bandwidth and resonance peak of frequency response. It has been proved that, there is a trade-off between larger bandwidth and lower resonance peak for base width effect.     

饱和非线性下零色散附近的交叉相位调制非稳

从光纤中扩展的耦合非线性薛定谔方程组出发,在饱和非线性光纤零色散附近,研究了不同二、四阶色散参量下交叉相位调制不稳定性增益谱及其临界扰动频率、谱宽和谱峰随两光波入射功率的演化特点.研究表明,随色散参量不同,增益谱随两光波入射功率的增大可能出现三种演化形式：一是始终是两个分离的谱区;二是由开始时的两个合成一个,最后再分离成两个;三是始终是一个谱区.饱和非线性的存在则使每个谱区的谱宽、谱峰及远离零点的临界扰动频率,随两光波入射功率的增大可能呈现出先增大后减小的特点,使第二谱区靠近零点的临界扰动频率呈现先减小后增大的特点,从而可能出现两个不同的输入功率对应同一个增益峰值和谱宽的情形.色散参量对增益谱的谱峰影响小,对谱宽影响大.越靠近零色散区,每个谱区谱宽越大,越易连成一个谱区.     

Cascaded Raman generation in optical fibers: influence of chromatic dispersion and Rayleigh backscattering

We study experimentally the influence of chromatic dispersion and Rayleigh backscattering on cascaded Raman generation in silica optical fibers. Effects ranging from enhanced spectral broadening of the Stokes orders to generation of higher Stokes order at unexpected wavelengths are observed. Additionally, we show that four-wave-mixing processes can quench the noisy Rayleigh lasing lines generated in power Raman amplifiers. Our observations are confirmed by numerical simulations.     

Propagation characteristics of nonlinear optical fibers with complex refractive index. A transmission line model approach

The transmission line model has been modified in order to evaluate nonlinear waves guided by optical fibers with complex refractive index. It is proven that the proposed model is able to tackle fibers with losses or gain, under the presence of arbitrary nonlinearity. The method is applied for the calculation of weakly guided lossy nonlinear optical fibers considering various configurations and Kerr nonlinearity. Power depended propagation characteristics have been calculated and plotted for the fundamental mode and the potential use of the method in optical fiber amplifiers with index nonlinearity is also discussed.     

基于光束偏转的扫描式宽带光参量啁啾脉冲放大

光参量啁啾脉冲放大(OPCPA)是超短激光脉冲领域的重要技术之一,增大增益带宽对提高OPCPA的转换效率、实现宽带光参量放大具有重要的意义.本文将光束偏转和非共线OPCPA有机结合,提出了基于光束偏转的扫描式宽带OPCPA模型.分析了通过光束偏转来时刻改变非共线角,以保证各频率成分的相位匹配,从而增大增益带宽的基本原理.采用提出的扫描式宽带OPCPA,针对800 nm中心波长、带宽约为100 nm信号光的光参量放大进行了数值计算.结果表明:经过扫描式OPCPA后,信号光的带宽与放大之前几乎相同,光谱没有窄化;扫描式OPCPA比固定非共线角方式的放大极大地增加了增益带宽和转换效率,实现了宽带的光参量放大;要满足信号光各频率成分的相位匹配,达到最大的增益带宽和转换效率,需要尽量减小加载到钽铌酸钾(KTa_(1-x) Nb_xO_3, KTN)电光晶体上的电压抖动和电压延时.     

25 GHz bandwidth Brillouin slow light in optical fibers

Broadband slow light is demonstrated by using stimulated Brillouin scattering in optical fibers based on a double Brillouin pump, the peaks of which are spectrally separated by twice the Brillouin frequency. The loss spectrum generated by one of the pump waves is fully compensated by the gain spectrum of the other one, which permits the enlargement of the bandwidth to 25 GHz and a variable time delay of up to 10.9 ps with 37 ps pulses.     

Calculation of the frequency response in step-index plastic optical fibers using the time-dependent power flow equation

The time-dependent power flow equation, which is reduced to its time-independent counterpart is employed to calculate frequency response and bandwidth in addition to mode coupling and mode-dependent attenuation in a step-index plastic optical fiber. The frequency response is specified as a function of distance from the input fiber end. This is compared to reported measurements. Mode-dependent attenuation and mode dispersion and coupling are known to be strong in plastic optical fibers, leading to major implications for their frequency response in data transmission systems.     

利用相位共轭技术补偿光纤中色散效应的条件

利用相位共轭器的频率反转特性的,补偿光纤中的色散效应,在理论上和实验上得到了证明.由色散脉冲的傅里叶交换确定了光纤中二次色散效应可以被忽略的条件,得到了共轭器的反射率和带宽与非线性介质的长度L,参数|K|L之间的关系曲线,找到了影响补偿效果的主要因素.     

Slow and fast light in quantum-well and quantum-dot semiconductor optical amplifiersInvited Paper

Slow and fast light in quantum-well (QW) and quantum-dot (QD) semiconductor optical amplifiers (SOAs) using nonlinear quantum optical effects are presented. We demonstrate electrical and optical controls of fast light using the coherent population oscillation (CPO) and four wave mixing (FWM) in the gain regime of QW SOAs. We then consider the dependence on the wavelength and modal gain of the pump in QW SOAs. To enhance the tunable photonic delay of a single QW SOA, we explore a serial cascade of multiple amplifiers. A model for the number of QW SOAs in series with variable optical attenuation is developed and matched to the experimental data. We demonstrate the scaling law and the bandwidth control by using the serial cascade of multiple QW SOAs. Experimentally, we achieve a phase change of 160° and a scaling factor of four at 1 GHz using the cascade of four QW SOAs. Finally, we investigate CPO and FWM slow and fast light of QD SOAs. The experiment shows that the bandwidth of the time delay as a function of the modulation frequency changes in the absorption and gain regimes due to the carrier-lifetime variation. The tunable phase shift in QD SOA is compared between the ground- and first excited-state transitions with different modal gains.     

Broadband gain-clamped linear quantum dash optical amplifiers

The linear optical gain of gain-clamped quantum dash semiconductor optical amplifiers (GCSOAs) has been investigated using the rate equation model. The gain spectrum of GCSOA for different wavelength detuning and different doping has been studied. Our analysis shows that the linear gain can be increased as the laser wavelength is detuned to high wavelength where the peak of the optical gain, which is found at wavelengths below the ground state wavelength, is shifted to lower wavelength as the laser wavelength is increased. We find that doping the dashes by either N-type or P-type enhances the linear optical gain and shifts the gain peak to lower wavelength. Moreover, we found that GCSOA with lightly N-type doping demonstrates large separation between the laser and the amplifier wavelength. Also we find that small inhomogeneous line broadening enhances the linear gain peak, shifts the gain peak to wavelength lower than the GS wavelength and widens the gain spectrum.     

Frequency response in step-index plastic optical fibers obtained by numerical solution of the time-dependent power flow equation

The time-dependent power flow equation is employed to calculate frequency response and bandwidth in addition to mode coupling and mode-dependent attenuation in step-index plastic optical fibers. Frequency response is specified in the paper as a function of fiber length. Results are found to match reported measurements better than the existing analytical solution does. Mode-dependent attenuation and mode dispersion and coupling are known to be strong in plastic optical fibers, leading to major implications for their frequency response.     

色散缓变光纤中的调制不稳定性分析

研究了色散缓变光纤中调制不稳定效应,得到了增益谱与光纤纵向色散参量的一般关系式.结果表明,色散缓变光纤较常规光纤具有较宽的增益谱.选取色散级变光纤的色散参量可以获得较大的增益带宽.数值模拟显示,利用色散缓变光纤中的调制不稳定性可以产生高重复率的基本孤子脉冲串.     

端面附近缺陷在掺铒光纤中引起的振荡

实验研究了由于掺铒光纤（ＥＤＦ）端面附近存在缺陷引起光反射而导致的振荡，这种振荡发生在掺铒光纤放大的自发辐射（ＡＳＥ）谱的峰值波长处，由于较长掺铒光纤的放大的自发辐射谱近似于其小信号增益谱，因此也可以认为发生在掺铒光纤放大器（ＥＤＦＡ）的最大增益处，对其增益产生不良影响。     

Gain characteristics and optimization of dual-pump fiber optical parametric amplifier using two-section highly nonlinear fibers

In this paper the gain characteristics of two-pump fiber optical parametric amplifiers (FOPA) with two-section highly nonlinear fibers are analyzed numerically and the parameters of the fibers are optimized to reach broad and flat gain spectra using genetic algorithm. Different from the previous methods, here the space between two pump wavelengths and the parameter β₄ of the fibers are included as a pivotal factor in the optimization. The numerical simulation shows that using two-section practical high nonlinear fibers, the amplifier may reach 110 nm bandwidth covering 1495–1605 nm with 10.5 dB average gain and gain ripple of 0.17 dB, when the total pump power is 1 W.