Tissue engineering scaffold material of nano-apatite crystals and polyamide composite

A new kind of tissue engineering scaffold materials of needle-like nano-hydroxyapatite (n-HA) and polyamide (PA) biocomposite is prepared by co-solution, co-precipitation method and water treatment under normal atmospheric pressure. The n-HA crystals uniformly distribute in the composite with a crystal size of 10-20 nm in diameter by 70-90 nm in length. The n-HA/PA composite has good homogeneity, high n-HA content (65 wt%), and high bioactivity. Strong molecule interactions and chemical bondings are present between the n-HA and PA in the composite, which are verified by IR, XPS and XRD. The composite has excellent mechanical properties close to the natural bone. The porous 3-D scaffold is made by injection foaming method, which has not only macropores, but also micropores on the walls of macropores. The porosity is 80% and the average macropore diameter is about 300 μm of the composite.The n-HA/PA composite can be used for tissue engineering and bone repair or substitute.     

Preparation and characterization of new materials based on silk fibroin,chitosan and nanohydroxyapatite

Abstract

In this paper, a series of porous nanohydroxyapatite/silk fibroin/chitosan (nHA/SF/CTS) scaffolds were successfully prepared using the freeze-drying method. The biomaterials were characterized by attenuated total reflection Fourier transform infrared spectroscopy, and mechanical testing and thermogravimetric analysis. Moreover, studies of porosity, pore size, swelling properties and in vitro degradation test were performed. Research has proved that micro-structure, porosity, water adsorption and compressive strength were greatly affected by the components’ concentration, in particular the content of silk fibroin. SEM observations showed that the scaffolds of nHA/SF/CTS are highly porous, with pore size in wide range from 25 to 300?µm which is suitable for cell growth. nHA/SF/CTS scaffolds have sufficient mechanical integrity to resist handling during implantation and in vivo loading. Both, the compressive modulus and compressive strength of the scaffold, decrease with the increase in silk fibroin content.     

Characterization of chitosan microparticles reinforced cellulose biocomposite sponges regenerated from ionic liquid

The chitosan-microparticles reinforced cellulose biocomposite sponges regenerated from ionic liquid were prepared and characterized. Fourier transform infrared (FTIR) spectroscopy confirmed that the cellulose dissolved in 1-allyl-3-methylimidazolium chloride without derivatization. Chitosan particles as reinforcement were incorporated into the cellulose matrix. FTIR spectra indicated hydrogen bonding between hydroxyl groups of cellulose and chitosan. The biocomposite sponges showed uniform three-dimensional interconnected porous structures. The breaking strength of the sponges increased significantly, from 0.09 to 0.32 MPa with the addition of 1.0 wt% chitosan. The sponges also demonstrated excellent antibacterial activity against S. aureus and E. coli with the average inhibition zone diameters >2 mm and the inhibition rate higher than 80 %. Furthermore, the biocomposite sponges exhibited good moisture penetrability and high porosity. The water uptake ability of the sponge was >25 times of its weight in water with a fast swelling. The chitosan/cellulose composite sponge is expected to be a promising material for potential applications as wound dressing.     

化学-物理法制备聚乙烯醇/壳聚糖/纳米羟基磷灰石复合水凝胶及其性能

采用化学 物理交联法制备了聚乙烯醇/壳聚糖/纳米羟基磷灰石（PVA/CS/n-HA）复合水凝胶材料。 通过对比其含水率、拉伸强度、红外光谱和TG谱图,探讨了PVA含量及戊二醛加入量对材料性能的影响。 结果表明,m(PVA)∶m（CS+n-HA）=5∶1,戊二醛质量分数为2%时,复合水凝胶材料具有较好的综合性能：含水率为82.0%、拉伸强度为2.14 MPa、断裂伸长率为343.26%;同步热分析表明,25~140 ℃,仅存在水分的蒸发,直至360 ℃材料才发生分解,说明材料的热稳定性良好;红外分析表明,CS与戊二醛发生了交联反应。     

Preparation and characterization of cellulose nanocrystals via ultrasonication-assisted FeCl3-catalyzed hydrolysis

Cellulose nanocrystals (CNC) was obtained from bamboo pulp via ultrasonication-assisted FeCl₃-catalyzed hydrolysis process, with parameters optimized by response surface methodology. The optimal parameters were reaction temperature: 107 °C, reaction time: 58 min, ultrasonication time: 186 min. The morphological, crystal structural, chemical structural and thermal features of the prepared cellulose nanocrystals were analyzed by scanning electron microscopy, transmission electron microscopy, X-ray diffraction (XRD), Fourier transfer infrared (FTIR) and thermogravimetric analysis. The results showed that the cellulose nanocrystals formed an interconnected network structure and CNC was rod-like with the length of 100–200 nm and the width of 10–20 nm. XRD result revealed that, compared with cellulose pulp, the crystallinity index of CNC increased from 69.5 to 79.4 %, while the cellulose I crystal structure remained. FTIR analysis demonstrated that CNC had the similar chemical structures to that of cellulose pulp, which indicated that the chemical structures of CNC remained unchanged in the presence of FeCl₃-catalyzed hydrolysis process and ultrasonication treatment. Thermogravimetric analysis revealed that the resulting CNC exhibited relatively high thermal stability. The research shows that ultrasonication-assisted FeCl₃-catalyzed hydrolysis could be a highly efficient method for preparing CNC.     

原位沉淀法制备CS/nHA多孔复合支架及其性能

通过原位沉淀法和冷冻相分离技术得到含有钙磷前驱体(CaP)的初始多孔支架, 利用多孔支架表面原位生成的壳聚糖(CS)膜减缓NaOH溶液中OH^-离子的渗透速率, 以达到纳米羟基磷灰石(nHA)缓慢形成的目的, 从而制得nHA 分布均匀的CS/nHA多孔复合支架. 利用扫描电镜(SEM)和万能试验机研究复合支架的结构和性能, 发现nHA为针状结构, 长度为80200 nm, 宽度为2050 nm. 随着nHA含量的增加, 复合支架的孔隙率下降, 由(93.8±3.3)%降至(87.7±3.8)%, 压缩强度则逐渐提高, 由(0.5±0.09) MPa增加至(1.5±0.06) MPa. 当复合支架中nHA质量分数为25%时, 未发现nHA团聚现象, nHA均匀地分布于CS基体中. 通过红外光谱(FTIR)、 X射线衍射(XRD)及X射线光电子能谱(XPS)等分析推断, nHA与CS之间可能存在配位和氢键作用. 细胞实验结果表明, CS/nHA多孔复合支架具有良好的生物相容性, 细胞在支架内部贴壁黏附生长. CS/nHA多孔复合支架有望在骨组织工程领域具有良好的应用前景.     

Characterization of biodegradable and cytocompatible nano-hydroxyapatite/polycaprolactone porous scaffolds in degradation in vitro

Porous nano-hydroxyapatite/polycaprolactone (nHA/PCL) scaffolds with different composition ratios of nHA/PCL were fabricated via a melt-molding/porogen leaching technique. All scaffolds were characterized before and after degradation in vitro for six months. The original scaffolds had high porosity at around 70% and showed decreasing compressive modulus (from 24.48 to 2.69 MPa for hydrated scaffolds) with the introduction of nHA. It was noted that the scaffolds could retain relatively stable architecture and mechanical properties for at least six months, although some slight changes happened with the nHA/PCL scaffolds in the mass, the nHA content, the PCL molecular weight and the crystallinity. Moreover, during the 7 days culture of bone marrow stromal cells (BMSCs) on scaffolds, the cell adhesion and proliferation of BMSCs were presented well on both the surface and the cross-section of the scaffolds. All of these results suggested the nHA/PCL scaffolds to be promising in bone tissue engineering.     

Hydrolyzable and bio-based polyester/nano-hydroxyapatite nanocomposites: Structure and properties

Hydrolyzable and bio-based poly(DHCA-co-HDA) (PDH)/nano-hydroxyapatite (n-HA) nanocomposites were fabricated by polycondensation of 3,4-dihydroxycinnamic acid (DHCA) and 10-hydroxydecanoic acid (HDA) with various amount of n-HA. The structure of nanocomposites was characterized by FT-IR. DSC results indicated that the T_gs of the nanocomposites were improved with increasing n-HA content. The SEM micromorphology revealed that n-HA nano-particles were well dispersed in PDH, which was due to the good compatibility between n-HA and PDH. With addition of n-HA in PDH, the tensile strength of nanocomposites prominently enhanced, however the elongation at break reduced. The presence of n-HA increased the hydrophilicity and hydrolysis rate of PDH/n-HA nanocomposites. Moreover, the hydrophilicity and degradation rate of nanocomposites can be altered through varying the content of n-HA.     

Preparation and characterization of composite membranes with Brønsted acidic ionic liquid

Poly-(vinyl alcohol) (PVA) proton-conducting composite membranes were prepared using succinic acid (SA) as a cross-linking agent and Brønsted acidic ionic liquid (BAIL) as a proton source. The incorporated BAILs resulted in a relatively high proton conductivity compared with PVA/SA membrane without BAILs. The proton conductivities of PVA/SA/BAIL composite membranes increased versus the BAIL content. In addition, the optimal resultant proton conductivity of PVA/SA/BAIL composite membrane under dry condition could reach 0.4 mS/cm at 140 °C, which was higher than that of PVA/sulfosuccinic acid (SSA) composite membrane (0.032 mS/cm), PVA/SSA/5-aminotetrazole membrane (0.022 mS/cm at 130 °C), and PVA/chlorosulfonic acid/glutaraldehyde membrane (0.0585 mS/cm at 90 °C) measured at the same condition. It was notable that the PVA/SA/BAIL composite membranes could reach high thermal stability up to 150 °C, which was higher than that of traditional PVA membranes (below 80 °C).     

纳米羟基磷灰石/聚乙烯醇/明胶复合材料的结构和力学性能

采用机械共混法、原位化学合成法、原位水热法制备了一系列纳米羟基磷灰石/聚乙烯醇/明胶(n-HA/PVA/GEL)复合材料;利用X射线衍射仪、透射电镜及傅立叶变换红外光谱仪等分析了复合材料的结构;利用材料试验机测定了复合材料的力学性能.结果表明,利用原位水热法可使n-HA有效地在PVA高分子中均匀分散,并提高n-HA颗粒...     

羟基磷灰石/聚乙烯醇/壳聚糖水凝胶在模拟体液中的力学性能

从仿生学角度出发,将自制的人工角膜支架材料羟基磷灰石/聚乙烯醇/壳聚糖(n-HA/PVA/CS)浸泡在模拟体液中,对材料的含水率及力学性能进行了测试,并利用扫描电镜、X射线衍射仪、电感耦合等离子体原子发射光谱仪及热重分析仪研究了材料在模拟体液中的形貌、晶体结构、元素组成及热稳定性.结果表明,在模拟体液中,n-HA/PVA/CS复合水凝胶的含水率为80%~86%,具有较高的拉伸强度,能承受正常眼压,且热稳定性较好.在浸泡后期,n-HA/CS/PVA复合材料对Ca2+的吸附和释放达到动态平衡;而其表面含有微量的纳米羟基磷灰石沉积,有利于纤维细胞的长入.     

In vitro degradation and release behavior of porous poly(lactic acid) scaffolds containing chitosan microspheres as a carrier for BMP-2-derived synthetic peptide

To develop a novel tissue engineering scaffold with the capability of controlled releasing BMP-2-derived synthetic peptide, porous poly(lactic acid)/chitosan microspheres (PLA/CMs) composites containing different quantities of chitosan microspheres were prepared by a thermally induced phase separation method. FTIR analysis revealed that there were strong hydrogen bond interactions between the PLA and chitosan component. Introduction of less than 30% CMs (on PLA weight basis) did not remarkably affect the morphology and porosity of the PLA/CMs scaffolds. The compressive strength of the composite scaffolds increased from 0.48 to 0.66 MPa, while the compressive modulus increased from 7.29 to 8.23 MPa as the microspheres' contents increased from 0% to 50%. In vitro degradability investigation indicated that the dissolution of chitosan component was preferential than PLA matrix and the inclusion of CMs could neutralize the acidity of PLA degradation products. Compared with the rapid release from CMs, the synthetic peptide was released from PLA/CMs scaffolds in a temporally controlled manner, mainly depending on the degradation of PLA matrix. The promising microspheres based scaffold release system can be used to deliver bioactive factors for a variety of non-loaded bone regeneration and tissue engineering application.     

Polyester scaffolds with bimodal pore size distribution for tissue engineering

This paper presents a method for the preparation of porous poly(L-lactide)/poly[(L-lactide)-co-glycolide] scaffolds for tissue engineering. Scaffolds were prepared by a mold pressing-salt leaching technique from structured microparticles. The total porosity was in the range 70-85%. The pore size distribution was bimodal. Large pores, susceptible for osteoblasts growth and proliferation had the dimensions 50-400 microm. Small pores, dedicated to the diffusion of nutrients or/and metabolites of bone forming cells, as well as the products of hydrolysis of polyesters from the walls of the scaffold, had sizes in the range 2 nm-5 microm. The scaffolds had good mechanical strength (compressive modulus equal to 41 MPa and a strength of 1.64 MPa for 74% porosity). Scaffolds were tested in vitro with human osteoblast-like cells (MG-63). It was found that the viability of cells seeded within the scaffolds obtained using the mold pressing-salt leaching technique from structured microparticles was better when compared to cells cultured in scaffolds obtained by traditional methods. After 34 d of culture, cells within the tested scaffolds were organized in a tissue-like structure. Photos of section of macro- and mesoporous PLLA/PLGA scaffold containing 50 wt.-% of PLGA microspheres after 34 d of culture. Dark spots mark MG-63 cells, white areas belong to the scaffold. The specimen was stained with haematoxylin/eosin. Bar = 100 microm.     

Development of nano-tricalcium phosphate/polycaprolactone/platelet-rich plasma biocomposite for bone defect regeneration

Nano-tricalcium phosphate (n-TCP) is an osteoconductive substance which, like polycaprolactone (PCL), has been used for clinical purposes for many years; It has now been licensed for a range of products for clinical and medication distribution. This research aimed to examine the effects of platelet-rich plasma on mesenchymal stem cell proliferation and osteogenic differentiation. Thus, we decided to examine the in vitro and in vivo actions of PRP-treated porous biocomposite scaffolds based on nano-tricalcium phosphate- polycaprolactone (n-TCP-PCL/PRP). The prepared samples were described utilizing FTIR, XRD, and SEM. MTT has measured the cytotoxicity of the biocomposite scaffolds. After two weeks of cell seeding, Alizarin red staining confirmed bone mineral formation by MSCs cells. Moreover, from day 4 to day 7, n-TCP-PCL/PRP biocomposite scaffold improved the expresses of bone marker genes. Platelet-rich plasma (PRP) in conjunction with nano-tricalcium phosphate- polycaprolactone (n-TCP-PCL) biocomposite scaffold is beneficial for the regeneration and stability of the freshly developed bone tissue.     

Porous composite scaffolds of hydroxyapatite/silk fibroin via two‐step method

A two‐step method was used to fabricate the hydroxyapatite (HAP)/silk fibroin (SF) scaffolds, i.e. the nano‐sized HAP/SF composite powders were prepared by co‐precipitation, which were then blended with SF solution to fabricate the HAP/SF composite scaffolds. The obtained scaffolds showed a 3D porous structure. The porosity was higher than 90% with the average macropore size of 214.2 µm. Moreover, the nano‐sized HAP/SF composite powders were uniformly dispersed in the silk fibroin matrix, which provided the scaffolds enhanced compressive properties. The cell culture assay showed that the scaffolds fabricated by the two‐step method could improve the cell proliferation and osteogenic differentiation when compared with those prepared by the conventional one‐step blending method. The results suggested that the two‐step method could promote the uniform dispersion of HAP in the SF matrix and efficient combination between the HAP and the matrix, which may provide a potential application in the composite scaffold preparation for tissue engineering. Copyright © 2009 John Wiley & Sons, Ltd.     

Optical,mechanical, and thermal behavior of poly(vinyl alcohol) composite films embedded with biosafe and optically active poly(amide–imide)-ZnO quantum dot nanocomposite as a novel reinforcement

Poly(vinyl alcohol) (PVA), a polyhydroxy polymer, is the synthetic resin produced in the world due to the physical properties and complete biodegradability. This work tries to introduce novel reinforcement for PVA to improve properties without effect on its biocompatibility. The present investigation deals with the fabrication of new PVA/poly(amide–imide)-zinc oxide nanocomposites (PVA/PAI–ZnO NCs) with different PAI–ZnO loading by using ultrasound irradiation. At first, the surface of ZnO nanoparticles (NPs) was modified by biosafe diacid for the better dispersion of NPs and increasing possible interactions between NPs and PAI. Then, PAI–ZnO was used as filler in the PVA matrix. Surface morphology results were amazing. The TEM images and related histograms show a noticeable size decreasing of ZnO NPs from about 31 to 3 nm after preparation of NCs. Other analyses showed that the reinforcement of PAI–ZnO NC into the PVA matrix enhances mechanical and thermal properties of the PVA composites.     

Improved cellular response on multiwalled carbon nanotube-incorporated electrospun polyvinyl alcohol/chitosan nanofibrous scaffolds

We report the fabrication of multiwalled carbon nanotube (MWCNT)-incorporated electrospun polyvinyl alcohol (PVA)/chitosan (CS) nanofibers with improved cellular response for potential tissue engineering applications. In this study, smooth and uniform PVA/CS and PVA/CS/MWCNTs nanofibers with water stability were formed by electrospinning, followed by crosslinking with glutaraldehyde vapor. The morphology, structure, and mechanical properties of the formed electrospun fibrous mats were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, and mechanical testing, respectively. We showed that the incorporation of MWCNTs did not appreciably affect the morphology of the PVA/CS nanofibers; importantly the protein adsorption ability of the nanofibers was significantly improved. In vitro cell culture of mouse fibroblasts (L929) seeded onto the electrospun scaffolds showed that the incorporation of MWCNTs into the PVA/CS nanofibers significantly promoted cell proliferation. Results from this study hence suggest that MWCNT-incorporated PVA/CS nanofibrous scaffolds with small diameters (around 160 nm) and high porosity can mimic the natural extracellular matrix well, and potentially provide many possibilities for applications in the fields of tissue engineering and regenerative medicine.     

Enhanced mechanical performance and biological evaluation of a PLGA coated β-TCP composite scaffold for load-bearing applications

Porous β-tricalcium phosphate (β-TCP) has been used for bone repair and replacement in clinics due to its excellent biocompatibility, osteoconductivity, and biodegradability. However, the application of β-TCP has been limited by its brittleness. Here, we demonstrated that an interconnected porous β-TCP scaffold infiltrated with a thin layer of poly(lactic-co-glycolic acid) (PLGA) polymer showed improved mechanical performance compared to an uncoated β-TCP scaffold while retaining its excellent interconnectivity and biocompatibility. The infiltration of PLGA significantly increased the compressive strength of β-TCP scaffolds from 2.90 to 4.19 MPa, bending strength from 1.46 to 2.41 MPa, and toughness from 0.17 to 1.44 MPa, while retaining an interconnected porous structure with a porosity of 80.65%. These remarkable improvements in the mechanical properties of PLGA-coated β-TCP scaffolds are due to the combination of the systematic coating of struts, interpenetrating structural characteristics, and crack bridging. The in vitro biological evaluation demonstrated that rat bone marrow stromal cells (rBMSCs) adhered well, proliferated, and expressed alkaline phosphatase (ALP) activity on both the PLGA-coated β-TCP and the β-TCP. These results suggest a new strategy for fabricating interconnected macroporous scaffolds with significantly enhanced mechanical strength for potential load-bearing bone tissue regeneration.     

Stabilization of Cs/Re trapping filters using magnesium phosphate ceramics

The present study a promising method for stabilizing spent filters trapping cesium and technetium by using magnesium phosphate ceramics. Simulated spent filters were fabricated by vaporizing nonradioactive cesium and rhenium (a surrogate of Tc) through the voloxidizer. In order to reveal the characteristics of spent filters, phase structures and thermal stability were analyzed by using X-ray diffraction (XRD), X-ray photoelectron spectroscopy, and thermogravimetric analysis techniques. Waste forms were fabricated by crushing spent filters and mixing them with magnesium oxide and potassium phosphate. Characterizations of the waste forms were performed by the analyses of compressive strength, apparent porosity, XRD, and scanning electron microscopy. The waste forms showed the excellent mechanical property compared with that of ordinary Portland cement, with the highest compressive strength of 38.1 MPa in the sample with 30 wt% of Cs-filter. Microstructural analysis suggests that waste materials are encapsulated by the binding matrix composed of magnesium potassium phosphate. The results of characterization suggest that fabricating a sound and durable waste form is possible with magnesium phosphate ceramics.     

Fabrication and Properties of Porous Collagen/Hyaluronic Composite Scaffolds Containing Nano-Bioactive Glass for Tissue Engineering

In this work, nano-structured scaffolds were designed for tissue engineering using collagen, hyaluronic acid (HA) and nano-bioactive glass (NBAG) as their main components. The scaffold was prepared via freeze-drying method and the properties including morphology, porosity, compressive strength, swelling ratio and cytotoxicity in-vitro, were also evaluated. The composite scaffolds showed well interconnected macropores with the pore size of ranging from 100 to 500 μm. The porosity percent and swelling ability were decreased with the introduction of NBAG into the collagen/HA hydrogel; however, the compressive strength was enhanced. The cytotoxicity in-vitro study shows that the collagen-HA/NBAG scaffolds have good biocompatibility with improving effect on fibroblastic cells growth. It could be concluded that this scaffold fulfills the main requirements to be considered as a bone substitute.