The use of indium(III) as a complexing counter-ion to enable the separation of chloride,bromide, and iodide using isotachophoresis

A new method has been devised to enable the determination of halide anions by isotachophoresis. This method uses an electrolyte system that employs indium(III) as a counter-ion to manipulate the effective mobilities of sample species by means of complexation reactions. This new procedure successfully enabled the simultaneous determination of the halide ions chloride, bromide, and iodide when a 12 mmol L^–1 nitrate-based leading electrolyte containing 3.5 mmol L^–1 indium(III) at pH 3.0 was used.     

Using ratiometric indicator-displacement assays in semi-quantitative colorimetric determination of chloride, bromide, and iodide anions

A ratiometric indicator-displacement assay (RIDA) array has been developed for the semi-quantitative colorimetric determination of chloride, bromide, and iodide anions. Determinations of these halide anions follow the displacement reaction using the chelate compound of (2-(3,5-dibromo-2-pyridylazo)-5-(diethylamino)phenol) (3,5-Br2-PADAP) and heavy metal salts as colorimetric reagent. Different from regular silver nitrate titrations, the chloride, bromide, and iodide anions compete with the 3,5-Br2-PADAP ligand and change the colour of the 3,5-Br2-PADAP-metal chelate compound dramatically. These clearer colour changes make the semi-quantitative colorimetric determination of chloride, bromide, and iodide anions possible. The colour changes are imaged using a conventional flatbed scanner, and digitized. After statistical analysis, these colour changes in the RIDA array provide facile identification of chloride, bromide, and iodide anions at a wide concentration range (10 μM to 10 mM) without any misclassification. The RIDA array is able to discriminate without misclassifications among seven concentrations of chloride, bromide, and iodide anions. No shelf life issue exists because the chelating compounds react with halide anions directly without any pre-immobilizations.     

Rapid chloride analysis using miniaturised isotachophoresis

A new design of miniaturised separation device for performing isotachophoresis (ITP) has been produced. The device contains a simple arrangement of channels comprising a single separation channel with a 'double T' injection geometry. The device was produced in poly(methyl methacrylate) and incorporates an on-column conductivity detector. A new electrolyte system was developed to enable the rapid determination of chloride to be made. This electrolyte system uses a leading ion of 3.5 mM nitrate at pH 3.0 with 0.5 mM indium(III) added as a complexing agent. Use of this electrolyte system with the new separation device allowed chloride samples to be analysed in under 100 s, with a limit of detection (LOD) calculated to be 2.2 mg l(-1).     

The simultaneous determination of chloride, nitrate and sulphate by isotachophoresis using bromide as a leading ion

A new method has been devised to allow the determination of small inorganic anions using isotachophoresis. This method makes use of indium(III) as a counter ion to manipulate the effective mobilities of inorganic anion species by means of complexation reactions. This new procedure successfully allowed the simultaneous determination of nitrate, chloride and sulphate to be realised on a capillary scale instrument and in a chip-based separation device. The electrolyte system developed to allow the separation to be achieved employed a 10mM bromide-based leading electrolyte containing 1.25 mM indium(III) at pH 3.15 and a terminating electrolyte of cyanoacetic acid.     

Indirect detection of halide ions via fluorescence quenching of quinine sulfate in microcolumn ion chromatography.

Halide ions could be visualized via fluorescence quenching in microcolumn ion chromatography. The fluorescence of quinine sulfate, which was contained in an acidic eluent, was quenched by halide ions. The observed fluorescence quenching values increased in this order: iodide, bromide, and chloride. The present detection system was relatively sensitive to halide ions except for fluoride: other anions gave smaller signals than halide ions. The present detection system provided quantitative information, so it could be applied to the determination of chloride in water samples.     

Determination of chlorine containing species in explosive residues using chip-based isotachophoresis

A new method has been developed to allow the determination of the chlorate, chloride and perchlorate anions in inorganic explosive residues to be made using isotachophoresis (ITP). To enable a good separation of these species to be achieved the method involves the use of two complexing agents. Indium(III) is used to allow the determination of chloride whilst using nitrate as the leading ion and alpha-cyclodextrin is used to allow the separation of chlorate and perchlorate. Separations were carried out using a miniaturised poly(methyl methacrylate) (PMMA) separation device. The method was applied to analysing both model samples and actual inorganic explosive containing residue samples. Successful determinations of these samples were achieved with no interference from other anions typically found in inorganic explosive residues. Limits of detection (LOD) for the species of interest were calculated to be 0.80 mg l(-1) for chloride, 1.75 mg l(-1) for chlorate and 1.40 mg l(-1) for perchlorate.     

Optimization of a flow injection system with amperometric detection for arsenic determination.

A selective and sensitive analytical procedure for rapid arsenic determination by gas-diffusion flow injection analysis with amperometric detection was developed. The method is based on the arsenite reduction by NaBH(4). Derived arsine diffuses through a PTF membrane into the acceptor flow stream and is amperometrically determined on a platinum working electrode. The limit of detection (3 sigma) at room temperature was 5 microg/dm(3) of As(III). The relative standard deviation for a 1 mg/dm(3) As(III) standard was 1.96% for six repetitive injections. Arsenic(V) was determined after its prereduction with potassium iodide. Arsenic determination was not interferred with by 1 mg/dm(3) Sb(III), 5 mg/dm(3) Sn(II), 10 mg/dm(3) Se(IV), 1 mg/dm(3) As(V), 1 mg/dm(3) hydrasine, 1 mg/dm(3) Fe(II) or 0.5 mg/dm(3) Fe(III) solution. The throughput of this method was 60 analyses per hour. This method was successfully applied to arsenic determination in some power plant waste water samples.     

In-capillary derivatization and determination of iodine in sodium chloride solution

A new capillary electrophoretic (CE) method was developed for the simple and selective determination of iodine in 0.5 mol l(-1) NaCl. The proposed method is based on the in-capillary derivatization of iodine with thiosulfate ions using the zone-passing technique and direct photometric detection of the iodide and tetrathionate formed. The optimal conditions for the separation and derivatization reaction were established by varying the concentration of iodine, electrolyte pH and applied voltage. The optimized separations were carried out in phosphate electrolyte (pH 6.86) using direct photometric detection at 253.7 nm. Common photometric detection absorbing anions such as Cl(-), NO(2)(-), S(2)O(3)(2-) did not give any interference. Valid calibration (r(2) = 0.994) is demonstrated in the range 16.5-198.1 mg l(-1) of iodine. The detection limit (calculated according to K. Doerffel, Statistik in der analytischen Chemie, 1990) was 11.53 mg l(-1) (by iodide peak area) and 8.45 mg l(-1) (by tetrathionate peak area). The proposed system was applied to the determination of iodine after oxidation of iodide in underground water.     

Thiocyanate and nitrite analysis using miniaturised isotachophoresis on a planar polymer chip

A new method has been developed to improve the determination of thiocyanate using isotachophoresis. This method uses complexation with copper(II) as a mechanism for improving the separation of thiocyanate from chlorate and perchlorate. By using a pH of 3.25 the method can also be used to analyse nitrite. Separations were carried out using a miniaturised poly(methyl methacrylate) (PMMA) separation device. Linearity was observed from 1.25 to 75 mg dm(-3) with a correlation coefficient of 0.998 for both thiocyanate and nitrite. Limits of detection for these two species were calculated to be 0.8 mg dm(-3) and 0.9 mg dm(-3) respectively. The method was successfully applied to the analysis of these anions in a range of samples including explosive residues.     

Simultaneous determination of bromide and iodide ions by capillary isotachophoresis using quaternary ammonium salts

Bromide and iodide ions were determined simultaneously by capillary isotachophoresis using an aqueous electrolyte system; the separation principle was based on the ion-pairing equilibria between tetradecyldimethylbenzylammonium ion and these anions in the leading electrolyte. The interaction between iodide ion and tetradecyldimethylbenzylammonium ion was stronger than that for bromide ion. Thus complete separation of bromide and iodide ions could be obtained by using a leading electrolyte containing 1.5 mM tetradecyldimethylbenzylammonium ion. The pH of the leading electrolyte was adjusted to 5.0. The relative standard deviations of the zone length for bromide and iodide ions were 1.1 and 1.2%, respectively, when mixture of 3.0 mM of these ions was analysed. A 150-μl volume could be injected for the simultaneous determination of low concentrations of bromide and iodide ions.     

Capillary electrophoresis determinations of trace concentrations of inorganic ions in large excess of chloride: soft modelling using artificial neural networks for optimisation of electrolyte composition

In this work, using a combination of experimental design (ED) and artificial neural networks (ANN), the composition of a triethanolamine-buffered chromate electrolyte was optimised for determination of sulphate anions in the presence of high chloride excess. The optimal electrolyte, allowing a baseline-resolved separation of sulphate from chloride present in a 1500 multiple excess in less than 170 s, consists of 10 mmol/L CrO(3), 2 mmol/L hexamethonium hydroxide, 10% methanol, and triethanolamine added to adjust the pH to 8.0. The method is suitable to a wide concentration range of chloride (4-1757 mg/L) and sulphate (4-590 mg/L) with linear calibration plots (R(2) = 0.9937-0.9999). Relative standard deviations are less than 2.0% for both anions for migration times and peak areas. The detection limits (hydrodynamic injection of 1 s) were 0.6 mg/L for sulphate and 0.5 mg/L for chloride. The method was successfully applied to determination of sulphate in mineral waters containing a high chloride concentration and to determination of sulphate traces in an anticancer drug injection preparation containing a physiological level of chloride. It was shown that alpha-cyclodextrin as an electrolyte additive has a significant potential for further increasing the separation selectivity for inorganic anions.     

离子液体中卤素离子杂质的离子色谱-直接电导检测法分析

研究了离子色谱-直接电导检测法分离测定离子液体中的卤素离子(F~-、Cl~-、Br~-)杂质.采用Shim-pack IC-A3阴离子交换色谱柱,考察了淋洗液种类及浓度、流速和色谱柱温度对分离测定的影响.最佳色谱条件为:以1.25 mmol/L邻苯二甲酸氢钾为淋洗液,流速1.5 mL/min,色谱柱温45 ℃.在此条件下可以基线分离卤素离子,且NO~-_3、BF~-_4、SO~(2-)_4不干扰测定.该法测定卤素离子的检出限(S/N=3)为0.02 ～0.11 mg/L,峰面积的相对标准偏差(n=5)不大于0.7%,F~-、Cl~- 和Br~- 的标准曲线的线性范围分别为0.1 ～50、0.1 ～50、0.5 ～100 mg/L.将方法用于烷基咪唑四氟硼酸盐离子液体中卤素离子杂质的测定,加标回收率为98% ～102%.     

Matrix elimination ion chromatography method for the determination of trace levels of anionic impurities in high purity cesium iodide

In the present study an ion chromatographic method based on matrix elimination has been developed for the determination of anionic impurities in high purity cesium iodide crystals. The presence of impurities has a detrimental effect on the characteristics of detectors based on cesium iodide crystals. In particular, oxygen-containing anions inhibit the resolving power of scintillators and decrease the optical absorption. The quantitative determination of anions (fluoride, chloride, bromide, nitrate, phosphate, and sulphate) simultaneously in the high-purity cesium iodide crystals has not been carried out before. The large concentration of iodide poses a challenge in the determination of anions (especially phosphate and sulphate); hence, matrix elimination is accomplished by adopting a sample pretreatment technique. The method is validated for linearity, accuracy, and precision. The limit of detection for different anions is in the range of 0.3-3 μg/g, and the relative standard deviation is in the range of 4-6% for the overall method.     

Spectrophotometric determination of chloride,bromide, and iodide with an improved mercury-iron-thiocyanate method

Stable reagents for the spectrophotometric mercury-iron-thiocyanate method for the determination of halide have been developed. The molar absorptivity for concentrations up to 170 μmole/liter of halide is for chloride 3.4 × 10³, for bromide 3.9 × 10³, and for iodide 4.0 × 10³. Above this concentration there is a slight decrease of the absorptivity for chloride and a slight increase for bromide and iodide.     

Capillary zone electrophoretic determination of iodide in seawater using transient isotachophoresis with artificial seawater as the background electrolyte

We describe an application of capillary zone electrophoresis (CZE) with transient isotachophoresis (ITP) as the on-line concentration procedure for the determination of iodide in seawater. The effective mobility of iodide was decreased by the addition of 10 mM cetyltrimethylammonium chloride (CTAC) to an artificial seawater background electrolyte (BGE) so that transient ITP functioned and iodide was separated from other coexisting anions such as bromide, nitrite, and nitrate in seawater samples. After sample injection, 600 mM acetate was separately injected into the capillary as the terminating ion to generate transient ITP. The limit of detection (LOD) for iodide was 3.0 microg/L. The LOD was obtained at a signal-to-noise ratio (S/N) of 3. The values of the relative standard deviation (RSD) of peak area, peak height, and migration time for iodide were 2.9, 2.1, and 0.6%. The proposed method was applied to the determination of iodide in seawater collected around the Osaka Bay. The results obtained by use of the calibration graph were agreed with those obtained by the addition of the standard solutions for iodide.     

Ligand dependence of metal-metal bonding in the d(3)d(3) dimers M(2)X(9)(n-) (M(III) = Cr, Mo, W; M(IV) = Mn, Tc, Re; X = F, Cl, Br, I)

The ligand dependence of metal-metal bonding in the d(3)d(3) face-shared M(2)X(9)(n-) (M(III) = Cr, Mo, W; M(IV) = Mn, Tc, Re; X = F, Cl, Br, I) dimers has been investigated using density functional theory. In general, significant differences in metal-metal bonding are observed between the fluoride and chloride complexes involving the same metal ion, whereas less dramatic changes occur between the bromide and iodide complexes and minimal differences between the chloride and bromide complexes. For M = Mo, Tc, and Re, change in the halide from F to I results in weaker metal-metal bonding corresponding to a shift from either the triple metal-metal bonded to single bonded case or from the latter to a nonbonded structure. A fragment analysis performed on M(2)X(9)(3-) (M = Mo, W) allowed determination of the metal-metal and metal-bridge contributions to the total bonding energy in the dimer. As the halide changes from F to I, there is a systematic reduction in the total interaction energy of the fragments which can be traced to a progressive destabilization of the metal-bridge interaction because of weaker M-X(bridge) bonding as fluoride is replaced by its heavier congeners. In contrast, the metal-metal interaction remains essentially constant with change in the halide.     

Precise and accurate determination of halogens in organic compounds using an amalgamated gold electrode

Precise and accurate titration of halogens in organic and inorganic materials has been studied. The halogen was titrated with coulometrically generated silver and determined potentiometrically by using an amalgamated gold indicator electrode. An argentometric titration curve using the amalgamated gold indicator electrode showed a large jump in potential at the endpoint as well as in mercurometric determination. Sodium carboxymethyl cellulose (CMC) and aluminum nitrate were added as they are most effective for clarifying the sample solution and eliminating adsorption of the halide ion on the silver halide generated. The electrolytes used were 0.5 M nitric acid containing 0.1% CMC and 0.2 M aluminum nitrate. Approximately 0.2 mmol of chloride, bromide, and iodide ions were titrated with high precision and accuracy. Their standard deviations were 0.03, 0.02, and 0.02%, respectively, with no apparent systematic error. The precise determination of halogens, employing oxygen flask combustion and dissolution of the halide salts in the electrolyte, was carried out with ±0.1% absolute error using samples weighing between 20 and 30 mg.     

Spectroscopic, structural, and theoretical studies of halide complexes with a urea-based tripodal receptor

A urea-based tripodal receptor L substituted with p-cyanophenyl groups has been studied for halide anions using (1)H NMR spectroscopy, density functional theory (DFT) calculations, and X-ray crystallography. The (1)H NMR titration studies suggest that the receptor forms a 1:1 complex with an anion, showing a binding trend in the order of fluoride > chloride > bromide > iodide. The interaction of a fluoride anion with the receptor was further confirmed by 2D NOESY and (19)F NMR spectroscopy in DMSO-d(6). DFT calculations indicate that the internal halide anion is held by six NH···X interactions with L, showing the highest binding energy for the fluoride complex. Structural characterization of the chloride, bromide, and silicon hexafluoride complexes of [LH(+)] reveals that the anion is externally located via hydrogen bonding interactions. For the bromide or chloride complex, two anions are bridged with two receptors to form a centrosymmetric dimer, while for the silicon hexafluoride complex, the anion is located within a cage formed by six ligands and two water molecules.     

Synthesis of silver nanowires and their applications in the electrochemical detection of halide

A silver nanowires modified platinum (Ag NWs/Pt) electrode was developed for simultaneous and selective determination of chloride, bromide and iodide ions by cyclic voltammetry in aqueous solutions. Silver nanowires were synthesized by an l-cysteine-assisted poly (vinyl pyrrolidone) (PVP)-mediated polyol route. X-ray diffraction (XRD) and scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) were employed to investigate the prepared nanowires. The intrinsic high surface area and the fast electron transfer rate ascribed from the nanowire structure could further improve halide detection performance. The determination was based on measurement of the well-separated oxidation peak currents of respective silver halides formed on the surface of silver during an anodic potential sweep. The concentration range was linear from 50 μM to 20.2 mM for bromide and iodide and 200 μM to 20.2 mM for chloride, and the sensitivity was 0.059 μA/mM, 0.042 μA/mM and 0.032 μA/mM for chloride, bromide and iodide, respectively. The correlation coefficient was 0.999 in each case. The Ag NWs/Pt electrode offered a useful platform for the development of a highly sensitive halide sensor.     

Development of a fully buffered molybdate electrolyte for capillary electrophoresis with indirect detection and its use for analysis of anions in Bayer liquor

A new counterion-buffered molybdate electrolyte was developed and optimized for simultaneous quantitative determination of up to eight anions (chloride, sulphate, oxalate, fluoride, formate, malonate, succinate, and acetate) in Bayer liquor by capillary electrophoresis with indirect detection at 214 nm. The separation parameters were optimized in respect to separation of the critical analyte group fluoride-formate-malonate, with the optimal electrolyte prepared from molybdic trioxide containing 5.0 mmol/L MoO3, 1.3 mmol/L cetyltrimethylammonium bromide (CTAB), and buffered with diethanolamine (DEA) to pH 9.2 (ca. 20 mM DEA). Total length of separation capillary was 80 cm, resulting in run time of under 4 min. The method is suitable for a wide concentration range of the analytes (1-50 mg/L) with linear calibration plots (R2 = 0.9983-0.9999). Relative standard deviations were 0.05%-0.07% for migration times and 0.67%-2.04% for peak areas. The detection limits were in the range of 0.17-0.51 mg/L or 2-10 micromol/L (hydrostatic injection of 30 s of 1000 x diluted sample). Due to its good buffering capacity, the electrolyte exhibited an excellent ruggedness and good tolerance to the alkaline samples. Consequently, Bayer liquor samples could be diluted as little as 100 x which allows more sensitive determination of minor components over previous methods. The method was successfully applied to analysis of Bayer liquor samples with recoveries in the range of 95-105%.