沙棘黄酮口服液中芦丁和5-羟色胺的毛细管区带电泳电化学检测

建立了毛细管区带电泳 -电化学检测法 (CE -ED)测定芦丁和5_羟色胺含量的方法 ,研究了电极电位、运行缓冲液的酸度和浓度、电泳电压及进样时间等因素对分离检测的影响,确定了最佳测定条件 ;以直径为300μm的碳圆盘电极为检测电极,电极电位为0.90V(vsSCE),在50mmol/L硼酸盐缓冲液(pH8.5)中,上述2组分在12min内完全分离 ,被分析物的电流响应与浓度在约3个数量级范围内呈良好线性关系,检出限分别为3×10-7 mol/L和8×10-8 mol/L ,7次测定含5.0×10-4 mol/L的芦丁和5_羟色胺的标准溶液,峰高的相对标准偏差分别为2.5 %和3.8 % ;该法成功地用于中药沙棘黄酮口服液中芦丁和5_羟色胺的测定     

芯片毛细管电泳-NDA柱前衍生荧光检测多巴胺及组胺

本文以汞灯为激发光源,利用自组装的高灵敏芯片毛细管电泳荧光光子计数器检测系统,NDA柱前衍生检测神经递质多巴胺和组胺。优化了NDA衍生多巴胺、组胺以及衍生后分离与检测的条件。本法多巴胺和组胺的检出限(S/N=3)分别为2.5×10-7mol/L、1.4×10-6mol/L。组胺和多巴胺可在45s内分离和检测。     

肉类中己烯雌酚的高速毛细管电泳安培法测定

采用高速毛细管电泳安培法对人工合成雌激素———己烯雌酚 (DES)的测定进行了研究 ;通过优化选择检测电位、毛细管内径和长度、分离电压、缓冲溶液等实验参数 ,DES在60s内可以得到较好的分离 ,检出限为1.0×10 -8mol/L ,DEC浓度在1.48×10 -4～3.69×10 -5mol/L ,1.25×10 -6～1.85×10 -7mol/L与峰面积分段呈良好的线性关系 ;迁移时间和峰面积的相对标准偏差分别为0.65 %、2.2 % ;将该法用于市售肉类中DES的检测 ,取得了满意的结果     

毛细管电泳-电化学检测测定茶叶中咖啡因、表儿茶素和抗坏血酸

高效毛细管电泳电化学检测同时测定了6种茶叶中的咖啡因、表儿茶素和抗坏血酸的含量,考察了实验参数对分离、检测的影响。在最佳实验条件下,以300 靘直径的碳圆盘电极为检测电极,检测电极为1.20 V(vs.SCE),在25 mmol/L硼酸盐25 mmol/L磷酸盐(pH 7.6)的混合运行缓冲液中,上述各组分在16 min内能完全分离。咖啡因、表儿茶素和抗坏血酸在2×10-3mol/L～１×10-5 mol/L、5×10-5mol/L～5×10-7mol/L、2×10-4 mol/L～1×10-5mol/L范围内呈线性关系,检测下限分别为6×10-6mol/L、4×10-7mol/L和1×10-6mol/L。该法直接用于茶叶中咖啡因、表儿茶素和抗坏血酸的测定,结果令人满意。     

β-环糊精存在下阳离子表面活性剂的毛细管电泳电导法测定

基于H3 BO3 与 β CD配合成大阴离子 ,与不同的阳离子表面活性剂作用不同 ,建立了快速分离检测阳离子表面活性剂的毛细管电泳电导法。研究了H3 BO3 与 β CD的浓度 ,缓冲液的酸度和浓度对分离的影响。在优化的实验条件下 ,溴化四丁基铵 (TBAB)、溴化十二烷基三甲基铵 (DTAB)、溴化十六烷基三甲基铵(CTMAB)阳离子表面活性剂 10min内完全分离 ,峰形良好。线性范围分别为TBAB 10 -3 ～ 10 -5mol/L ,DTAB1.0× 10 -3 ～ 5 .0× 10 -6mol/L ,CTMAB 1.0× 10 -3 ～ 5 .0× 10 -6mol/L。检测限分别为TBAB 7.5× 10 -6mol/L ,DTAB 1.7× 10 -6mol/L ,CTMAB 1.0× 10 -6mol/L。方法用于合成水样分析 ,结果令人满意     

黄芩及其制剂中黄芩素和黄芩甙的

用毛细管区带电泳 -电化学检测法测定了黄芩及其制剂中黄芩素和黄芩甙的含量。研究了电极电位、电解液酸度和浓度、电泳电压及进样时间等对电泳的影响 ,得到了较为优化的测定条件。以直径为300μm的碳圆盘电极为检测电极 ,电极电位为0.90V(vsSCE) ,在100mmol/L硼酸盐缓冲液(pH9.0)中 ,上述两组分在8min内完全分离。黄芩素和黄芩甙浓度与电泳峰电流分别在5.0×10 -7～1.0×10 -3mol/L和1.0×10 -6～1.0×10 -3mol/L范围内呈良好线性 ,检出限分别为2.24×10 -7mol/L和5.48×10 -7mol/L。7次测定分别含5.0×10 -4mol/L黄芩素和黄芩甙试样溶液 ,峰高的相对标准偏差分别为3.53%和4.03%。     

毛细管电泳-间接化学发光法检测染发剂中苯二酚异构体和苯酚

根据某些酚类化合物在碱性条件下具有能猝灭鲁米诺-铁氰化钾体系化学发光信号的特性,建立了毛细管电泳-间接化学发光分离检测苯二酚异构体和苯酚的新方法.电泳缓冲溶液选用7.5 mmol/L Na2B4O7-2.5 mmol/L Na2HPO4.在优化的化学发光和电泳条件下,对苯二酚、间苯二酚、邻苯二酚和苯酚在10 min内可直接实现分离,其检出限(S/N=3)分别为2.9×10-8 mol/L、3.7×10-7 mol/L、8.4×10-8 mol/L和4.4×10-6 mol/L;相对标准偏差(RSD)为2.5%～4.8%(n=5).通过对不同染发剂实际样品进行分离分析研究,证明该方法可以用于实际染发剂样品的分析测定,结果令人满意.     

高效毛细管电泳电导检测对阴离子表面活性剂分离测定的研究

以Ca2 +为分离介质 ,甲酰胺为添加剂 ,通过对缓冲体系、缓冲液浓度、酸度、Ca2 +浓度、甲酰胺浓度、电泳电压和进样时间的优化选择 ,用毛细管电泳 -电导检测法分离了十二烷基硫酸钠(K12)和十二烷基苯磺酸钠(LAS) ;在10mmol/LTris -11mmol/LCit(pH4.5)运行缓冲液中 ,上述两组分在16min内完全分离 ;K12和LAS的线性范围分别为5.0×10-6～8.0×10-3 mol/L和5.0×10-6 ～5.0×10-3 mol/L ;检出限(S/N=3)分别为2.5×10-6 和3.0×10-6 mol/L,应用于合成洗衣粉样和合成水样中K12 和LAS测定 ,结果令人满意。     

散利痛中扑热息痛和异丙基安替比林的毛细管区带电泳电化学检测法测定

毛细管区带电泳 -电化学检测法同时测定散利痛片中有效成分扑热息痛和异丙基安替比林的含量 ;研究了电极电位、电解液浓度和酸度、电泳电压及进样时间等对电泳的影响 ,得到了最优化的测定条件 ;以直径为300μm的碳圆盘电极为检测电极 ,工作电极电位为1.0V(vsSCE) ,在50mmol/L硼砂 -NaOH(pH9.35)运行缓冲液中 ,上述两组分在8min内完全分离 ;扑热息痛和异丙基安替比林线性范围分别为2×10-3～5×10 -6mol/L和2×10 -3～2×10 -6mol/L,检出限分别为5×10 -6mol/L和2×10 -6mol/L ;7次平行进样的相对标准偏差(RSD)为3.5%和1.8 % ,加标回收率(n=3)分别为101 %和98% ,该法灵敏可靠 ,结果令人满意。     

手性药物心得安对映体的毛细管电泳/电化学分离检测研究

报道了采用毛细管电泳 -方波安培检测法对手性药物对映体———外消旋心得安进行了分离检测研究。以5mmol/LNaOH -8mmol/L柠檬酸 -10mmol/Lβ_CD(pH4.5)为电泳介质 ,未涂层熔融石英毛细管(75μm×45cm)为分离通道 ,分离电压 +12.5kV ,实现了心得安对映体的基线分离。方法的线性范围为2.0×10 -6～1.0×10 -4mol/L ,检出限为5.0×10 -7mol/L。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.