Study on preparation and formation mechanism of n-alkanol/water emulsion using alpha-cyclodextrin

Surfactants are usually used for the preparation of emulsions; however, some have an adverse effect on the human body such as skin irritation, hemolysis, and protein denaturation, etc. In this study, we examined the preparation and formation mechanism of n-alkanol/water emulsions using alpha-cyclodextrin (alpha-CD) as an emulsifier. Emulsions were prepared by mixing oil and water phases for 4 min at 2500 rpm using a vortex mixer. The mechanism of emulsification was investigated with some physico-chemical techniques. From phase diagrams of n-alkanol/alpha-CD/water systems, the emulsion phase extended as the chain length of n-alkanols and the amount of alpha-CD added increased. Furthermore, the emulsion was not formed in the region where the n-alkanol/alpha-CD complex didn't precipitate; however, the emulsion was formed in the region where the complex precipitated. In addition, it was clear that the emulsions have a yield stress value and correspond to the Maxwell model from rheological measurement. Our experiments clearly showed that the stable emulsions are formed because the precipitated complexes form a dense film at the oil-water interface and prevent aggregation among dispersed phases. Furthermore, it is suggested that the creation of a three-dimensional network structure formed by precipitated complexes in the continuous phase contributes to the stabilization of the emulsion. Thus, we concluded that the n-alkanol/water emulsions using alpha-cyclodextrin were a kind of the Pickering emulsion.     

Fabrication of macroporous foam and microspheres of polystyrene by Pickering emulsion polymerization

Poly(styrene-co-methacrylic acid) (PS-co-MAA) particles were synthesized via surfactant-free emulsion polymerization and then used as particulate emulsifiers for preparation of Pickering emulsions. Our results showed that adjusting the solution pH can tune the wettability of PS-co-MAA particles to stabilize either water-in-oil (W/O) or oil-in-water (O/W) Pickering emulsions. Stable W/O emulsions were obtained with PS-co-MAA particles at low pH values due to their better affinity to the dispersed oil phase. In contrast, increasing the pH value significantly changed the stabilizing behavior of the PS-co-MAA particles, leading to the phase inversion and formation of stable O/W emulsions. We found that the oil/water ratio had a significant influence on pH value of the phase inversion. It decreased with decreasing the oil/water ratio, and no phase inversion occurred when the styrene volume fraction reduced to 10 %. Additionally, macroporous polystyrene (PS) foam and PS microspheres were obtained via polymerization of Pickering high internal phase emulsion (Pickering HIPE) and O/W Pickering emulsion, respectively.     

Comparison of Pickering and network stabilization in water-in-oil emulsions

We compared the efficacy of Pickering crystals, a continuous phase crystal network, and a combination thereof against sedimentation and dispersed phase coalescence in water-in-oil (W/O) emulsions. Using 20 wt % water-in-canola oil emulsions as our model, glycerol monostearate (GMS) permitted Pickering-type stabilization, whereas simultaneous usage of hydrogenated canola oil (HCO) and glycerol monooleate (GMO) primarily led to network-stabilized emulsions. A minimum of 4 wt % GMS or 10 wt % HCO was required for long-term sedimentation stability. Although there were no significant differences between the two in mean droplet size with time, the free water content of the network-stabilized emulsions was higher than Pickering-stabilized emulsions, suggesting higher instability. Microscopy revealed the presence of crystal shells around the dispersed phase in the GMS-stabilized emulsions, whereas in the HCO-stabilized emulsion, spherulitic growth in the continuous phase and on the droplet surface occurred. The displacement energy (E(disp)) to detach crystals from the oil-water interface was ～10(4) kT, and was highest for GMS crystals. Thermal cycling to induce dispersed phase coalescence of the emulsions resulted in desorption of both GMS and GMO from the interface, which we ascribed to solute-solvent hydrogen bonding between the emulsifier molecules and the solvent oil, based on IR spectra. Overall, Pickering crystals were more effective than network crystals for emulsion stabilization. However, the thermal stability of all emulsions was hampered by the diffusion of the molten emulsifiers from the interface.     

Can polymersomes form colloidosomes?

Hydroxy-functionalized polymersomes (or block copolymer vesicles) were prepared via a facile one-pot RAFT aqueous dispersion polymerization protocol and evaluated as Pickering emulsifiers for the stabilization of emulsions of n-dodecane emulsion droplets in water. Linear polymersomes produced polydisperse oil droplets with diameters of ～50 μm regardless of the polymersome concentration in the aqueous phase. Introducing an oil-soluble polymeric diisocyanate cross-linker into the oil phase prior to homogenization led to block copolymer microcapsules, as expected. However, TEM inspection of these microcapsules after an alcohol challenge revealed no evidence for polymersomes, suggesting these delicate nanostructures do not survive the high-shear emulsification process. Thus the emulsion droplets are stabilized by individual diblock copolymer chains, rather than polymersomes. Cross-linked polymersomes (prepared by the addition of ethylene glycol dimethacrylate as a third comonomer) also formed stable n-dodecane-in-water Pickering emulsions, as judged by optical and fluorescence microscopy. However, in this case the droplet diameter varied from 50 to 250 μm depending on the aqueous polymersome concentration. Moreover, diisocyanate cross-linking at the oil/water interface led to the formation of well-defined colloidosomes, as judged by TEM studies. Thus polymersomes can indeed stabilize colloidosomes, provided that they are sufficiently cross-linked to survive emulsification.     

Synthesis of millimeter‐sized hydrogel beads by inverse Pickering polymerization using starch‐based nanoparticles as emulsifier

The preparation of millimeter‐sized poly(acrylamide‐co‐acrylic acid) hydrogel beads via inverse Pickering emulsion polymerization using starch‐based nanoparticles (SNPs) as stabilizers is reported. Amphiphilic starch is fabricated by the introduction of butyl glycidyl ether groups and palmitate groups, and the hydrophobically modified SNPs are fabricated by a nanoprecipitation process. The obtained SNPs could adsorb at oil‐water interfaces to stabilize an inverse Pickering emulsion, and the effects of oil/water volume fraction ratio and SNP concentration on emulsions are comprehensively studied. Poly(acrylamide‐co‐acrylic acid) hydrogel beads with a size of approximately 1 mm are obtained by inverse Pickering emulsion polymerization stabilized by SNPs. The morphology and structure of hydrogel beads are extensively investigated, which confirms that SNPs locate on the surface of hydrogel beads and act as emulsifiers and network structures present inside the beads. Polymerization is also detected to investigate the potential formation mechanism of hydrogel beads. The pH‐responsive property of hydrogel beads and its potential application for drug delivery are also explored.     

Particle self-assembly in oil-in-ionic liquid Pickering emulsions

We have studied polydimethylsiloxane (PDMS)-in-1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]) Pickering emulsions stabilized by polystyrene microparticles with different surface chemistry. Surprisingly, in contrast to the consensus originating from oil/water Pickering emulsions in which the solid particles equilibrate at the oil-water droplet interfaces and provide effective stabilization, here the polystyrene microparticles treated with sulfate, aldehyde sulfate, or carboxylate dissociable groups mostly formed monolayer bridges among the oil droplets rather than residing at the oil-ionic liquid interfaces. The bridge formation inhibited individual droplet-droplet coalescence; however, due to low density and large volume (thus the buoyant effect), the aggregated oil droplets actually promoted oil/ionic liquid phase separation and distressed emulsion stability. Systems with binary heterogeneous polystyrene microparticles exhibited similar, even enhanced (in terms of surface chemistry dependence), bridging phenomenon in the PDMS-in-[BMIM][PF(6)] Pickering emulsions.     

颗粒乳化剂的研究及应用

近年来,颗粒乳化剂因其在食品、采油、化妆品、医药、催化以及功能纳米材料制备等领域具有潜在应用前景而备受关注。本文综述了近来颗粒乳化剂的研究进展,归纳了颗粒乳化剂的种类,包括:无机纳米粒子、表面改性或杂化的无机粒子、有机纳米粒子以及特殊的颗粒乳化剂Janus粒子;并对颗粒乳化剂能够在油水界面稳定吸附的热力学机理和动力学行为进行了阐述,颗粒乳化剂在油水界面接触角以及粒径大小是其在界面稳定吸附的关键参数,而颗粒在油水界面的排布方式则主要受粒子之间相互作用的影响。重点介绍了颗粒乳化剂的热点应用,包括:(1)利用颗粒乳化剂制备Pickering乳液,以及通过对颗粒乳化剂的功能化,使得Pickering乳液具备环境响应性(即pH、盐浓度、温度、紫外光、磁场敏感响应性);(2)以颗粒乳化剂为构筑基元、以Pickering乳液为模板制备Janus颗粒、Colloidosome、具有多级结构的粒子或膜,以及多孔结构材料;(3) Janus粒子在催化领域的应用。     

Particle self-assembly at ionic liquid-based interfaces

This review presents an overview of the nature of ionic liquid (IL)-based interfaces and self-assembled particle morphologies of IL-in-water, oil- and water-in-IL, and novel IL-in-IL Pickering emulsions with emphasis on their unique phenomena, by means of experimental and computational studies. In IL-in-water Pickering emulsions, particles formed monolayers at ionic liquid–water interfaces and were close-packed on fully covered emulsion droplets or aggregated on partially covered droplets. Interestingly, other than equilibrating at the ionic liquid–water interfaces, microparticles with certain surface chemistries were extracted into the ionic liquid phase with a high efficiency. These experimental findings were supported by potential of mean force calculations, which showed large energy drops as hydrophobic particles crossed the interface into the IL phase. In the oil- and water-in-IL Pickering emulsions, microparticles with acidic surface chemistries formed monolayer bridges between the internal phase droplets rather than residing at the oil/water–ionic liquid interfaces, a significant deviation from traditional Pickering emulsion morphology. Molecular dynamics simulations revealed aspects of the mechanism behind this bridging phenomenon, including the role of the droplet phase, surface chemistry, and inter-particle film. Novel IL-in-IL Pickering emulsions exhibited an array of self-assembled morphologies including the previously observed particle absorption and bridging phenomena. The appearance of these morphologies depended on the particle surface chemistry as well as the ILs used. The incorporation of particle self-assembly with ionic liquid science allows for new applications at the intersection of these two fields, and have the potential to be numerous due to the tunability of the ionic liquids and particles incorporated, as well as the particle morphology by combining certain groups of particle surface chemistry, IL type (protic or aprotic), and whether oil or water is incorporated.     

纳米玉米醇溶蛋白微球稳定的O/W型Pickering乳液

利用相分离工艺制备玉米醇溶蛋白(zein)纳米微球,微球粒径可控制在40 nm左右;经旋转蒸发制得zein溶胶体系,zein溶胶具有明显的丁达尔现象,静置数月不聚沉,Zeta电位法测得zein微球在pH值为4.0时分散性能最佳。 以纳米zein微球为固相稳定剂制备O/W型Pickering乳液,考察了zein胶体加入量、油水体积比等因素对乳液稳定性的影响。 实验结果表明,zein胶体加入量的质量分数控制为0.4%,高油水体积比将有利于Pickering乳液的长时间稳定。 基于zein分子的两亲结构和界面组装特点,提出了zein微球稳定Pickering乳液的作用机制。     

Effects of Surface Properties on Rheological and Interfacial Properties of Pickering Emulsions Prepared by Fumed Silica Suspensions Pre-Adsorbed Poly(N-Isopropylacrylamide)

The hydrophobic fumed silica suspensions physically pre-adsorbed poly(N-isopropylacrylamide) (PNIPAM) in water could prepare oil dispersed in water (O/W) Pickering emulsion by mixing of silicone oil. The resulting Pickering emulsions were characterized by the measurements of volume factions of emulsified silicone oil, adsorbed amounts of the silica suspensions, oil droplet size, and some rheological responses, such as stress-strain sweep curve and dynamic viscoelastic moduli as a function of the added amount of PNIPAM. Moreover, their characteristics were compared with those of the O/W Pickering emulsions prepared by the hydrophilic fumed silica suspensions pre-adsorbed PNIPAM. For the emulsions prepared by the hydrophobic silica suspensions, an increase in the added amount of PNIPAM led to (1) a decrease in the volume fraction of the emulsified oil in the emulsified phase, (2) both the size of oil droplets and the adsorbed amount of the corresponding silica suspensions being almost constant, except for the higher added amounts, and (3) both the storage modulus (G′) and the yield shear strain being constant. The term of 1 is the same for the emulsions prepared by the hydrophilic silica suspensions, whereas both the adsorbed amount of the corresponding silica suspension and the G′ value increase and both the droplet size and the yield shear strain decrease with an increase in the added amount of PNIPAM. The differences between the rheological properties of the emulsions prepared by the hydrophilic silica suspensions and those by the hydrophobic ones are attributed to the hydrophobic interactions of the flocculated silica particles in the Pickering emulsions.     

Surface compaction versus stretching in Pickering emulsions stabilised by microgels

Colloidal gel particles called microgels have shown their ability to adsorb at an oil–water interface and stabilise emulsion named Pickering emulsions. Such particles are soft, deformable, and porous, and they can swell or contract under the action of an external stimulus. These specificities make them emulsifiers of special interest as they offer a large versatility to emulsions and materials elaborated thereof. This modularity is in counterpart at the origin of an abundant and often contradictory literature. The aim of this paper is to review recent advances in the emulsion stabilisation mechanism, particularly focusing on the microgel conformation at the interface in relation with the mechanical interface behaviour and the emulsion macroscopic stability. A sum up of the unambiguous knowledge is also proposed as well as few central questions that remain to be answered to in the domain.     

Silicone-protein surfactants; stability of water-in-silicone oil emulsions

Small scale water-in-silicone oil emulsions were readily prepared using high speed mixers. Two surfactant systems were studied: a comb-type silicone-polyether surfactant, and a surfactant system employing a mixture of the surface active protein human serum albumin (HSA, in the internal phase) and an alkoxysilane-modified silicone TES-PDMS in the silicone oil (continuous phase). Little difference in particle sizes was noted between the two surfactant types for a given mixing protocol, but dual-blade turbulent mixing led to relatively monodisperse particles of approximately 2–5 m in diameter while high speed Dremel mixers led to bimodal particle distributions. Prior to spontaneous demulsification of the latter emulsions stabilized by HSA/TES-PDMS (the 3225C emulsions remain stable), they proved very difficult to break. The addition of dibutyltin dilaurate to the HSA/TES-PDMS-stabilized emulsions led to catastrophic collapse of the emulsion and formation of a silicone elastomer at the bulk water/oil interface. This makes unlikely the possibility that silicone elastomers, formed by protein-catalyzed crosslinking of the alkoxysilane in albumin/TES-PDMS-stabilized emulsions, are involved in stabilizing the emulsion. The nature of the stabilization of the interface is discussed.     

Simple, reversible emulsion system switched by pH on the basis of chitosan without any hydrophobic modification

Chitosan without hydrophobic modification is not a good emulsifier itself. However, it has a pH-tunable sol-gel transition due to free amino groups along its backbone. In the present work, a simple reversible Pickering emulsion system based on the pH-tunable sol-gel transition of chitosan was developed. At pH > 6.0, as adjusted by NaOH, chitosan was insoluble in water. Chitosan nanoparticles or micrometer-sized floccular precipitates were formed in situ. These chitosan aggregates could adsorb at the interface of oil and water to stabilize the o/w emulsions, so-called Pickering emulsions. At pH < 6.0, as adjusted by HCl, chitosan was soluble in water. Demulsification happened. Four organic solvents (liquid paraffin, n-hexane, toluene, and dichloromethane) were chosen as the oil phase. Reversible emulsions were formed for all four oils. Chitosan-based Pickering emulsions could undergo five cycles of emulsification-demulsification with only a slight increase in the emulsion droplet size. They also had good long-term stability for more than 2 months. Herein, we give an example of chitosan without any hydrophobic modification to act as an effective emulsifier for various oil-water systems. From the results, we have determined that natural polymers with a stimulus-responsive sol-gel transition should be a good particulate emulsifier. The method for in situ formation of pH-responsive Pickering emulsions based on chitosan will open up a new route to the preparation of a wide range of reversible emulsions.     

Pickering乳液的制备和应用研究进展

Pickering乳液是一种由固体粒子代替传统有机表面活性剂稳定乳液体系的新型乳液。与传统乳液相比,Pickering乳液具有强界面稳定性、减少泡沫出现、可再生、低毒、低成本等优势,在化妆品、食品、制药、石油和废水处理等行业具有广阔的应用前景,受到越来越多研究者们的关注。本文综述了近年来Pickering乳液的研究进展,先介绍Pickering乳液相对于表面活性剂乳液的特色与优势,然后介绍Pickering乳液的制备研究进展,最后介绍Pickering乳液的应用研究进展。     

Enzyme-Polymer-Conjugate-Based Pickering Emulsions for Cell-Free Expression and Cascade Biotransformation

In this study, we addressed the limitations of conventional enzyme-polymer-conjugate-based Pickering emulsions for interfacial biocatalysis, which traditionally suffer from nonspecific and uncontrollable conjugation positions that can impede catalytic performance. By introducing a non-canonical amino acid (ncAA) at a specific site on target enzymes, we enabled precise polymer-enzyme conjugation. These engineered conjugates then acted as biocatalytically active emulsifiers to stabilize Pickering emulsions, while encapsulating a cell-free protein synthesis (CFPS) system in the aqueous phase for targeted enzyme expression. The resulting cascade reaction system leveraged enzymes expressed in the aqueous phase and on the emulsion interface for optimized chemical biosynthesis. The use of the cell-free system eliminated the need for intact whole cells or purified enzymes, representing a significant advancement in biocatalysis. Remarkably, the integration of Pickering emulsion, precise enzyme-polymer conjugation, and CFPS resulted in a fivefold enhancement in catalytic performance as compared to traditional single-phase reactions. Therefore, our approach harnesses the combined strengths of advanced biochemical engineering techniques, offering an efficient and practical solution for the synthesis of value-added chemicals in various biocatalysis and biotransformation applications.     

Role of liquid crystal in the emulsification of a gel emulsion with high internal phase fraction

A gel emulsion with high internal oil phase volume fraction was formed via an inversion process induced by a water–oil ratio change. The process involved the formation of intermediate multiple emulsions prior to inversion. The multiple emulsions contain a liquid crystal formed by the surfactant with water; this was both predicted by the equilibrium phase diagram as well as observed using polarization microscopy. These multiple emulsions were more stable compared to alternative multiple emulsions prepared in the same way with a surfactant that does not form liquid crystals. While the formation of a stable intermediate multiple emulsion may not be a necessary condition for the inversion to occur, the transitional presence of a liquid crystal proved to be a significant factor in the stabilization of the intermediate multiple emulsions. The resulting gel emulsion contained a small fraction of the liquid crystal according to the phase diagram, and it exhibited excellent stability.     

Pickering emulsions: Versatility of colloidal particles and recent applications

The versatility of colloidal particles endows the particle stabilized or Pickering emulsions with unique features and can potentially enable the fabrication of a wide variety of derived materials. We review the evolution and breakthroughs in the research on the use of colloidal particles for the stabilization of Pickering emulsions in recent years for the particle categories of inorganic particles, polymer-based particles, and food-grade particles. Moreover, based on the latest works, several emulsions stabilized by the featured particles and their derived functional materials, including enzyme immobilized emulsifiers for interfacial catalysis, 2D colloidal materials stabilized emulsions as templates for porous materials, and Pickering emulsions as adjuvant formulations, are also summarized. Finally, we point out the gaps in the current research on the applications of Pickering emulsions and suggest future directions for the design of particulate stabilizers and preparation methods for Pickering emulsions and their derived materials.     

Synergetic Effect of Reactive Surfactants and Clay Particles on Stabilization of Nonaqueous Oil-in-Oil (o/o) Emulsions

Although surfactants and particles are often used together in stabilization of aqueous emulsions, the contribution of each species to such stabilization at the oil-water interface is poorly understood. The situation becomes more complicated if we consider the nonaqueous oil-oil interface, i.e, the stabilization of nonaqueous oil-in-oil (o/o) emulsions by solid particles and reactive surfactants which, to our knowledge, has not been studied before. We have prepared Pickering nonaqueous simple (o/o) emulsions stabilized by a combination of kaolinite particles and a nonionic polymerizable surfactant Noigen RN10 (polyoxyethylene alkylphenyl ether). Different pairs of immiscible oils were used which gave different emulsion stabilities. Using kaolinite with equal volumes of paraffin oil/formamide system gave no stable emulsions at all concentrations while the addition of Noigen RN10 enhanced the emulsion stability. In contrast, addition of Noigen RN10 surfactant to silicon oil-in-glycerin emulsions stabilized by kaolinite resulted in destabilization of the system at all concentrations. For all systems studied here, no phase inversion in simple emulsion was observed by altering the volume fraction of the dispersed phase as compared to the known water-based simple Pickering emulsions.      

Phase inversion of the Pickering emulsions stabilized by plate-shaped clay particles

We investigated the phase inversion of Pickering emulsions stabilized by plate-shaped clay particles. Addition of water induced a phase inversion from a water-in-oil (W/O) emulsion to an oil-in-water (O/W) emulsion when the amount of the oil phase exceeded a limiting amount of oil absorption to solid particles. On the other hand, a phase inversion from a powdery state to an O/W emulsion state through an oil-separated state is observed when the amount of an oil phase is less than the limiting amount of the oil absorption. Interestingly, the oil separated is re-dispersed as emulsion droplets into the O/W emulsion phase. This type of phase inversion, which is a feature of the Pickering emulsions stabilized by the clay particles, is caused by a change in the aggregate structures of particles.     

Fat crystals and water-in-oil emulsion stability

Products such as cosmetics, pharmaceuticals, and crude oil often exist as water-in-oil (W/O) emulsions during their processing or in final form. In many cases, their dispersed aqueous phase is encased in a crystal network and/or by interfacially-adsorbed (‘Pickering’) particles [paraffins, triacylglycerols, polymers, etc.] that promote emulsion kinetic stability by hindering droplet–droplet contact, coalescence and macroscopic phase separation. In processed foods, important questions remain regarding whether a continuous phase fat crystal network or Pickering crystal provides better stabilization. This review explores the following factors related to crystal-stabilized W/O emulsions: i) the key properties dictating fat crystal spatial distribution (at the interface or in the continuous phase); ii) how temperature and freeze–thaw emulsion destabilization are intimately linked with fat crystal spatial distribution, and; iii) why oil-soluble surfactant interactions with the continuous oil phase influence fat crystal wettability and emulsifier efficacy. It is shown that these parameters strongly govern W/O emulsion formation and stability.