Synthesis and characterization of Ni-Zn ferrite nanoparticles

Nickel zinc ferrite nanoparticles Ni_xZn_1−xFe₂O₄ (x=0.1, 0.3, 0.5) have been synthesized by a chemical co-precipitation method. The samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, electron paramagnetic resonance, dc magnetization and ac susceptibility measurements. The X-ray diffraction patterns confirm the synthesis of single crystalline Ni_xZn_1−xFe₂O₄ nanoparticles. The lattice parameter decreases with increase in Ni content resulting in a reduction in lattice strain. Similarly crystallite size increases with the concentration of Ni. The magnetic measurements show the superparamagnetic nature of the samples for x=0.1 and 0.3 whereas for x=0.5 the material is ferromagnetic. The saturation magnetization is 23.95 emu/g and increases with increase in Ni content. The superparamagnetic nature of the samples is supported by the EPR and ac susceptibility measurement studies. The blocking temperature increases with Ni concentration. The increase in blocking temperature is explained by the redistribution of the cations on tetrahedral (A) and octahedral (B) sites.     

Effect of Cd on the structural, magnetic and electrical properties of nanostructured Mn-Zn ferrite

Nanoparticles of Mn_0.5Zn_0.5−xCd_xFe₂O₄ (x=0.0, 0.1, 0.2 and 0.3) have been synthesized by a chemical co-precipitation method. The lattice constant increases with increasing Cd content. X-ray calculations indicate that there is deviation in the cation distribution in the nanostructured spinel ferrite. The dielectric constant and dielectric loss decrease for the samples with Cd content up to x=0.2. However the dielectric constant rises for x=0.3. This is due to an increase in the hopping process at the octahedral (B sites). The dielectric constant increases with increase in temperature, indicating a thermally activated hopping process. The DC resistivity increases with Cd content up to x=0.2 and decreases for Cd content x=0.3. The maximum magnetization of all the samples decreases with increase in Cd content.     

Magnetic and structural studies of the Mn-doped Mg–Zn ferrite nanoparticles synthesized by the glycine nitrate process

In this study, Nanocrystalline Mn–Mg–Zn ferrite with the chemical formula Mn_xMg_0.5−xZn_0.5Fe₂O₄ (x=0, 0.1, 0.2, 0.3, 0.4, 0.5) was successfully synthesized by the glycine-nitrate autocombustion process using glycine as a fuel and nitrates as oxidants. The as-synthesized powders were characterized by the X-ray diffraction analysis, field emission scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR) and vibrating sample magnetometer. The X-ray diffraction data was used to determine the lattice constant, cation distribution and the oxygen position parameter. The results reveal that the nanocrystalline Mn–Mg–Zn ferrite has an average crystallite size of 35–67 nm and particle size of 40 nm. The lattice parameter increases linearly with an increase in the Mn content. The FTIR analysis confirms the intrinsic vibrational frequencies of the tetrahedral and octahedral of the spinel structure. The magnetic measurements indicate that the coercivity decreases, and the magnetization increases by increasing the Mn content.     

A Structural,Magnetic and Mössbauer Study of Tb0.3Dy0.7(Fe1−x Al x )1.95 Alloys

A structural, magnetic and Mössbauer study of a series of Tb_0.3Dy_0.7(Fe_1–x Al _x )_1.95 alloys (x=0, 0.05, 0.1, 0.15, 0.20, 0.25, 0.30, 0.35) at room temperature is presented. It was found that the primary phase of the Tb_0.3Dy_0.7(Fe_1–x Al _x )_1.95 alloys is the MgCu₂-type cubic Laves phase structure when x<0.3 and a small amount of a second phase, RFe₃ (R: rare-earth element), is present when 0.3x0.35. The lattice constant of the Tb_0.3Dy_0.7(Fe_1–x Al _x )_1.95 alloys increases approximately monotonically with increasing x. The substitution of Al increases slightly the magnetostriction in a low magnetic field (H500 Oe). However, the magnetostriction decreases sharply, but is saturated more easily with increasing x in a higher applied field. The analysis of the Mössbauer spectra allows the determination of the easy axes of magnetization in these alloys. Moreover, the dependence of the hyperfine-field, isomer shift and quadrupole splitting on the Al concentration, x, for the Tb_0.3Dy_0.7(Fe_1–x Al _x )_1.95 alloys are reported and discussed.     

Doping effect of Mn on the magnetic behavior in Ni-Zn ferrite nanoparticles prepared by sol-gel auto-combustion

The ferrite samples of a chemical formula Ni_0.5−xMn_xZn_0.5Fe₂O₄ (where x=0.0, 0.1, 0.2, 0.3, 0.4, and 0.5) were synthesized by sol-gel auto-combustion method. The synthesized samples were annealed at 600 °C for 4 h. An analysis of X-ray diffraction patterns reveals the formation of single phase cubic spinel structure. The lattice parameter increases linearly with increase in Mn content x. An initial increase followed by a subsequent decrease in saturation magnetization with increase in Mn content is observed showing inverse trend of coercivity (H_c). Curie temperature decreases with increase in Mn content x. The initial permeability is observed to increase with increase in Mn content up to x=0.3 followed by a decrease, the maximum value being 362. Possible explanation for the observed structural, magnetic, and changes of permeability behavior with various Mn content are discussed.     

Minimizing of power loss in Li-Cd ferrite by nickel substitution for power applications

The effect of Ni substitution on the microstructure, dielectric, impedance, magnetic and power loss properties has been investigated on a series of Li_0.35-0.5xCd_0.3Ni_xFe_2.35-0.5xO₄ (0.00≤x≤0.08) ferrite prepared by citrate precursor method. Dielectric and impedance measurements have been determined in the frequency range 100 Hz-10 MHz. An enhancement in permittivity was observed with Ni concentration and exhibits the maximum value of ∼7×10³ for x=0.02 sample. The impedance spectroscopy technique has been used to study the effect of grain and grain boundary on the electrical properties of all the samples. Power loss measurements have been carried out in the frequency range 50 kHz-5 MHz at induction condition of B=10 mT. Power loss has been found to be quite low, less than 100 kW/m³ up to 500 kHz, with the substitution of Ni in Li_0.35-0.5xCd_0.3Ni_xFe_2.35-0.5xO₄ ferrite, which is useful for technological aspects.     

Study of the magnetic and electronic properties of the Fe4N with pressure

In the present work, we report ab-initio studies of the magnetic property variations with pressure of both iron sites in the structure of Fe₄N, using full-potential linearized augmented plane wave method and the Perdew–Burke–Ernzerhof functional and generalized gradient approximation to describe the exchange-correlation potential are reported. The results show that the magnetic moment of FeI is almost constant while the magnetic moment of FeII presents a discontinuity when the lattice parameter is varied. This is reflected in the compression of the spin up and down energy bands to different concentration points. The variation in the FeII magnetization arises mainly from changes in the d_xy, d_xz, d_yz and d_x2−y2 orbitals.     

New Mg0.5CoxZn0.5−xFe2O4 nano-ferrites: Structural elucidation and electromagnetic behavior evaluation

In this work cobalt substituted magnesium zinc nanocrystalline spinel ferrites having general formula Mg_0.5Co_xZn_0.5−xFe₂O₄ where x = 0.1, 0.2, 0.3, 0.4, 0.5 were synthesized using micro-emulsion technique. The Co substituted samples annealed at 700 °C and characterized by various characterization techniques, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), dielectric measurements and vibrating sample magnetometer (VSM). XRD analysis confirmed single phase spinel structure and the crystalline size calculated by Scherrer's formula found to be in 21.38–45.5 nm range. The lattice constant decreases as substitution of Co is increased. The decrease in lattice constant is attributed to the smaller ionic radius of cobalt as compared to zinc ion. The FTIR spectra reveled two prominent frequency bands in the wave number range 400–600 cm⁻¹ which confirm the cubic spinel structure and completion of chemical reaction. The dielectric parameters were observed to decrease with the increased Co contents. The peaking behavior was observed beyond 1.8 GHz. The frequency dependent dielectric properties of all these nanomaterials have been explained qualitatively in accordance with Koop's phenomenological theory. Magnetic studies revealed that the coercivity (H_c) attains maximum value of 818 Oe at ∼21 nm. The increasing trend of magnetic parameters (coercivity and retentivity) is consistent with crystallinity. The crystallite size is small enough to attain considerable signal to noise ratio in high density recording media. The optimized magnetic parameters suggest that the material with composition Mg_0.5Co_0.5Fe₂O₄ may have potential applications in high density recording media.     

Mössbauer effect study of the pseudo-binary system (Ti1−x Nb x )Fe2

Mössbauer spectroscopy and X-ray diffraction measurements have been done on (Ti_1–x Nb _x )Fe₂ compounds in order to investigate the effect of Nb on the magnetic properties of TiFe₂. The experimental results show that Nb enters the lattice by filling Ti sites, thereby forming a continuous phase over the whole range of Nb concentrations. The Mössbauer spectra at 80 K fitted with a magnetic hyperfine field distribution show a continuous decrease of the average magnetic hyperfine field with increasing Nb concentration, as well as several different magnetic configurations forx0.3.     

Novel structural and magnetic properties of Mg doped copper nanoferrites prepared by conventional and wet methods

Nanoferrites of the general formula Cu_1−xMg_xFe₂O₄ with 0≤x≤0.6 were prepared by standard ceramic and wet methods. The structure was studied by X-ray diffraction and IR spectroscopy. The density and lattice constant were calculated and reported. The particle size of the prepared nanoferrites ranged from 8.7 to 41.1 nm. It was found that the lattice parameter decreases with increasing cation substitution of Mg²⁺ due to the difference of ionic radius and atomic mass. The dc magnetic susceptibility was measured out using Faraday's method. The magnetic hysteresis measurement was performed using a vibrating sample magnetometer. Magnetic constants such as Curie temperature, effective magnetic moment, saturation magnetization, remanent magnetization and corecivicty were obtained and reported. The magnetic constants decrease with increasing Mg²⁺, except the remanent magnetization which increased.     

Spectral studies of Co substituted Ni-Zn ferrites

The spinel ferrites Zn_0.35Ni_0.65−xCo_xFe₂O₄, 0≤x≤1, have been prepared using the standard ceramic technique. Room temperature Mössbauer, X-ray and infrared IR spectra were used for carrying out this study. X-ray patterns reveal that all the samples have single-phase cubic spinel structure. The Mössbauer spectra of the samples show a paramagnetic phase for x=0 and a six-line magnetic pattern and a central paramagnetic phase for x≥0.1. They are analyzed and attributed to two magnetic subpatterns and two quadrupole doublets due to Fe³⁺ ions at the tetrahedral A-sites and octahedral B-sites. Four absorption bands are observed in IR spectra. They confirm the spinel structure of the samples and existence of Fe³⁺ ions in the sample sublattices. The deduced hyperfine interactions, lattice parameters, absorption band positions and intensities and force constant are found to be dependent on the substitution factor x, where the cation distribution is estimated. The hyperfine magnetic fields, magnetization and lattice resonant frequency are found to be dependent on the interionic distance.     

Thermoelectric power and magnetic properties of Cu doped NiZn ferrite for technological application

A series of samples in the system Ni_0.65Zn_0.35Cu_xFe_2-xO₄ (x = 0, 0.1, 0.2, 0.3, 0.4 and 0.5) were prepared by the usual ceramic technique. The thermoelectric power and the magnetic susceptibility were measured. The transition from the ferrimagnetic to the paramagnetic state is accompanied by an increase in the thermo EMF. NiZn ferrite shows n-type conductivity due to the presence of Fe²⁺ ions. The addition of Cu²⁺ ions creates lattice vacancies which give rise to p-type conductivity.

The Tawfik coefficient was determined for NiZn ferrite in the paramagnetic state. This coefficient was reduced by addition of Cu up to x < 0.5.     

Structural and optical properties of Ba(Ti1−x,Nix)O3 thin films prepared by sol–gel process

Ba(Ti_1−x,Ni_x)O₃ thin films were prepared on fused quartz substrates by a sol–gel process. X-ray diffraction and Raman scattering measurements showed that the films are of pseudo-cubic perovskite structure with random orientation and the change of lattice constant caused by Ni-doping with different concentrations is very small. Optical transmittance spectra indicated that Ni-doping has an obvious effect on the energy band structure. The energy gap of Ba(Ti_1−x,Ni_x)O₃ decreased linearly with the increase of Ni concentration. It indicates that the adjusting of band gap can be achieved by controlling the Ni-doping content accurately in Ba(Ti_1−x,Ni_x)O₃ thin films. This has potential application in devices based on ferroelectric thin films.     

Structural and magnetic properties of zinc- and aluminum-substituted cobalt ferrite prepared by co-precipitation method

Spinal ferrites having the general formula Co_{1 − x} Zn _x Fe_{2 − x} Al _x O₄ (x = 0.0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6) were prepared using the wet chemical co-operation technique. The samples were annealed at 800°C for 12 h and were studied by means of X-ray diffraction, magnetization and low field AC susceptibility measurements. The X-ray analysis showed that all the samples had single-phase cubic spinel structure. The variation of lattice constant with Zn and Al concentration deviates from Vegard’s law. The saturation magnetization σ _s and magneton number n _B measured at 300 K using high field hysteresis loop technique decreases with increasing x, suggesting decrease in ferrimagnetic behaviour. Curie temperature T _C deduced from AC susceptibility data decreases with x, suggesting a decrease in ferrimagnetic behaviour.      

Magnetic anisotropy of lithium aluminum ferrites

The temperature dependence of the first magnetic-anisotropy constant of Li_0.5Fe_2.5–xAl_xO₄ (x = 0, 0.2, 0.4) ferrites is calculated on the basis of the single-ion model with an account of biquadratic indirect exchange. The coefficients governing the splitting caused in the levels of Fe³⁺ in tetrahedral and octahedral positions by the lattice field are found.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii Fizika, No. 8, pp. 7–11, August, 1969.The author thanks A. I. Perveeva for programming the computer solution for the temperature dependences of the sublattice magnetizations, and E. P. Naiden for discussion of some of these results.     

Sol–gel auto-combustion synthesis,structural and enhanced magnetic properties of Ni substituted nanocrystalline Mg–Zn spinel ferrite

Nanocrystalline arrays of Ni²⁺ substituted Mg–Zn spinel ferrite having a generic formula Mg_0.7−xNi_xZn_0.3Fe₂O₄ (x=0.0, 0.2, 0.4 and 0.6) were successfully synthesized by sol–gel auto-combustion technique. The fuel used in the synthesis process was citric acid and the metal nitrate-to-citric acid ratio was taken as 1:3. The phase, crystal structure and morphology of Mg–Ni–Zn ferrites were investigated by X-ray diffraction, scanning electron microscopy, and Fourier transformer infrared spectroscopy techniques. The lattice constant, crystallite size, porosity and cation distribution were determined from the X-ray diffraction data method. The FTIR spectroscopy is used to deduce the structural investigation and redistribution of cations between octahedral and tetrahedral sites of Mg–Ni–Zn spinel structured material. Morphological investigation suggests the formation of grain growth as the Ni²⁺ content x increases. The saturation magnetization and magneton number were determined from hysteresis loop technique. The saturation magnetization increases with increasing Ni²⁺ concentration ‘x’ in Mg–Zn ferrite.     

Structural, magnetic and transport properties of double perovskite compounds (Sr2−3xLa2xBax)FeMoO6

The crystal structure and magnetic properties of a series of ordered double perovskite oxides (Sr_2−3xLa_2xBa_x)FeMoO₆ (0x0.3) have been investigated. X-ray powder diffraction reveals that the crystal structure of the compounds changes from a tetragonal I4/m lattice to a cubic lattice around x=0.2. Though the nominal average size of the A site cation of (Sr_2−3xLa_2xBa_x)FeMoO₆ is designed to be almost independent of x, the refinements of the crystal structure show that the lattice constants increase with x in both the tetragonal and the cubic phase regions due to electron doping. As the x increases, the degree of cationic ordering on the B site is decreased pronouncedly, while the Curie temperature of the compounds is nearly unchanged. The saturation magnetization of the compounds decreases with x and shows a linear dependence on the degree of cation ordering. The resistivity of the parent compound shows a semiconducting behavior below room temperature, but those of the doped samples exhibit a metal–semiconductor transition. A correlation between the resistivity and metal-semiconducting transition temperature (T_M−S) is observed. The resistivity and T_M−S of the compounds decrease with x for x0.2 and increase for x0.2. Magnetoresistance of the compounds is reduced by the La/Ba doping. All these observations can be understood based on the interplay of the electron doping, change in bandwidth and the anti-site defect concentration.     

Temperature dependent Mössbauer and neutron diffraction studies of Cu x Fe1−x Cr2S4 compounds

The cation distribution and magnetic structure of Cu _x Fe_1?x Cr₂S₄ (x?=?0.1, 0.2, 0.3, 0.4, and 0.5) has been studied by X-ray and neutron diffraction, vibrating sample magnetometer (VSM), and Mössbauer spectroscopy. The charge state of Fe is found to be ferrous (Fe²⁺) for the x?=?0.1 sample; ferric (Fe³⁺) for the x?=?0.5 sample; mixed state (Fe²⁺, Fe³⁺) for the x?=?0.2, 0.3, and 0.4 samples. The Mössbauer spectra of the x?=?0.1 sample show asymmetric line broadening, which is considered to be due to the Jahn–Teller effect of Cu²⁺ ions, and a symmetrical six-line pattern is shown for the x?=?0.5 sample. The valence state of the Cu ions for the x?=?0.1 and 0.5 samples is found to be divalent and monovalent, respectively. The magnetic structure of the samples was determined to be a ferrimagnetic structure with antiparallel alignment of the Fe and Cr ion magnetic moments.     

High permeability and low power loss of Ti and Zn substitution lithium ferrite in high frequency range

The effect of Zn and Ti on the magnetic, power loss and structural properties of Li_0.5Zn_xTi_xMn_0.05Fe_2.45−2xO₄ ferrites (x=0.0 to 0.30 in step of 0.05)+0.5 wt% Bi₂O_3, prepared by standard ceramic technique, has been investigated. Complex permeability (μ*=μ′−jμ″) has been analyzed at room temperature in frequency range from 1 to 10³ MHz. It was found an enhancement in permeability with Ti and Zn concentration in Li_0.5Zn_xTi_xMn_0.05Fe_2.45−2xO₄ and exhibits the maximum value 106 for x=0.20 sample. Complex permeability of these ferrites exhibits stable frequency response up to 7 MHz beyond which the real part decreases sharply and imaginary part increases to have a peak at the relaxation frequency. Power loss measurements have been carried out in induction condition (B=10 mT) in frequency range of 50 kHz to 3 MHz. Power loss has been found to be quite low with the substitution of Ti and Zn in lithium ferrite.     

Impact of zinc substitution on the structural and magnetic properties of chemically derived nanosized manganese zinc mixed ferrites

Mn_1−xZn_xFe₂O₄ nanoparticles (x=0-1) were synthesized by wet chemical co-precipitation techniques. X-ray diffraction, transmission electron microscopy and high-resolution transmission electron microscopy were effectively utilized to investigate the different structural parameters. The elemental analysis was conducted using energy-dispersive spectrum and inductively coupled plasma analysis. The magnetic properties such as magnetization and coercivity were measured using vibrating sample magnetometer. The observed magnetization values of the nanoparticles were found to be lower compared to the bulk counterpart. The magnetization showed a gradual decrease with zinc substitution except for a small increase from x=0.2 to 0.3. The Curie temperature was found to be enhanced in the case of ferrites in the nanoregime. The variation in lattice constant, reduced magnetization values, variation of magnetization with zinc substitution, the presence of a net magnetic moment for the zinc ferrite and the enhancement in Curie temperature in Mn_1−xZn_xFe₂O₄ all provide evidence to the existence of a metastable cation distribution together with possible surface effects at the nanoregime.