Characterization of Starch/Acrylic Acid Super‐Absorbent Hydrogels Prepared by Ionizing Radiation

Copolymerization of acrylic acid (AAc) and gelatinized maize starch in aqueous medium using γ‐irradiation, followed by neutralization with alkali solution was carried out. The preparation conditions, such as irradiation dose and starch/AAc compositions were investigated. The higher the irradiation dose, as well as the AAc content in the feed solution, the higher the gel content. The copolymers were characterized by FTIR spectroscopy, thermo‐gravimetric analysis (TGA) and scanning electron microscopy (SEM). SEM revealed that the higher the dose, the lower the copolymer pore size. Starch/AAc copolymers have thermal stability higher than that for starch and poly acrylic acid individually. The swelling of starch/AAc hydrogels reduced as the gel content increases. The maximum water absorption obtained for starch/AAc hydrogels in distilled water was 200 g/g, and for neutralized starch/AAc hydrogels was 350 g/g. The swelling ratio of starch/AAc hydrogels of different compositions in NaCl solution is lower than that obtained in distilled water. The results suggest that the neutralized starch/AAc hydrogels have a high swelling property, and can be used in a variety of commercial applications.     

K-型卡拉胶/聚乙烯吡咯烷酮共混水凝胶的辐射合成

采用辐射技术合成了K 型卡拉胶 (KC) /聚乙烯吡咯烷酮 (PVP)共混水凝胶 ,研究了天然高分子KC、单体N 乙烯基吡咯烷酮 (N VP)、交联剂二甲基丙烯酸十四甘醇酯 ( 1 4G) ,辐照剂量以及剂量率等对辐射合成的KC/PVP共混水凝胶性质的影响 .实验发现 ,KC与适当比例的N VP共混后在一定剂量范围内辐照可得到高强度、高溶胀行为的KC/PVP共混水凝胶 ,随着共混凝胶内KC含量的相对增加 ,凝胶强度及溶胀性的能均显著提高 ,但合成该共混凝胶的最佳剂量却相对提前 ;加入 1 4G后降低了KC/PVP共混凝胶辐射合成最佳剂量 ,同时使KC/PVP共混凝胶的强度进一步提高 ;剂量、剂量率对KC/PVP共混凝胶的性质亦有很大的影响 .分析表明 ,KC与N VP共混后 ,在较低剂量下KC的降解被抑制 ,从而获得一种由物理交联的KC和化学交联的PVP形成的互穿网络 (IPN)凝胶     

Taguchi optimized synthesis of collagen-g-poly(acrylic acid)/kaolin composite superabsorbent hydrogel

A novel biopolymer-based hydrogel composite was synthesized through chemical crosslinking by graft copolymerization of partially neutralized acrylic acid onto the hydrolyzed collagen. The Taguchi method, a robust experimental design, was employed for the optimization of the synthesis based on the swelling capacity of the hydrogels. This method was applied for the experiments and standard L16 orthogonal array with five factors and four levels. In the synthesis of the composite superabsorbent, N,N′-methylene bisacrylamide (MBA) as crosslinker, ammonium persulfate (APS) as initiator, acrylic acid (AA) as monomer, neutralization percent (NU), and collagen/kaolin weight ratio were used as important factors. From the analysis of variance of the test results, the most effective factor controlling equilibrium swelling capacity was obtained and maximum water absorbency of the optimized final product was found to be 674 g/g. The surface morphology of the gel was examined using scanning electron microscopy. Furthermore in this research, swollen gel strength of composite SAPs already swollen under realistic conditions (saline solution absorbency under load) was determined.     

Superabsorbent hydrogel composites

A new cost‐effective approach to enhance gel strength of superabsorbent hydrogels was invented. Superabsorbent hydrogel composites (SHCs) were prepared through an optimized rapid solution polymerization of concentrated partially neutralized acrylic acid in the presence of a crosslinking agent under normal atmospheric conditions. Kaolin was used as an inorganic component in the polymerization process to strengthen the hydrogel products. FT‐IR spectroscopy was used to confirm grafting of acrylic chains on to the surface of kaolin particles. Morphology of the products was studied by scanning electron microscopy (SEM). Compared with the kaolin‐free hydrogel (control), kaolin caused a reduced equilibrium swelling and swelling rate as low as 17–31% and 19–29%, respectively. Kaolin, however, resulted in enhanced gel strength as high as 21–35% compared to the control. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to study thermal properties of the composites. The SHCs exhibited higher thermal stability than the control. Meanwhile, changes in certain thermal transitions reconfirmed the chemical interaction of the acrylic chain with kaolin. These thermostabilized strengthened superabsorbent hydrogels may be considered as good candidates for agricultural application to retain more water under soil pressure. Copyright © 2003 John Wiley & Sons, Ltd.     

Radiation synthesis of hydrogels based on copolymers of vinyl ethers of monoethanolamine and ethyleneglycol and their interaction with poly(acrylic acid)

Novel hydrogels of cationic nature were synthesized by gamma-radiation copolymerization of vinyl ethers of monoethanolamine and ethyleneglycol in the presence of cross-linking agent. The effect of absorbed dose on the gel fraction and equilibrium swelling degree of hydrogels in water is shown. It was demonstrated that the hydrogels are able to bind poly(acrylic acid) to form polyelectrolyte complexes with swelling properties typical for polyampholytes.     

Designing of pH-responsive ketorolac tromethamine loaded hydrogels of alginic acid: Characterization,in-vitro and in-vivo evaluation

pH-responsive hydrogels based on alginic acid grafted with acrylic acid and ethylene glycol dimethylacrylate in the presence of ammonium persulfate were developed for controlled delivery of Ketorolac tromethamine. The alginic acid based hydrogels were prepared by free radical polymerization technique. Increase in gel fraction was observed with the increase in alginic acid, acrylic acid, and ethylene glycol dimethylacrylate content. The dynamic swelling and drug release studies were conducted at two different pH values (pH 1.2 and 7.4). Maximum swelling and drug release were observed at pH 7.4. The characterization of prepared hydrogels was carried out by using Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, powder x-ray diffraction, and scanning electron microscopy. Similarly, in-vivo study was performed on rabbits and greater plasma drug concentration was achieved by fabricated hydrogels as compared to drug solution and commercial product Keten. Conclusively, the fabricated hydrogels can be considered as a potential candidate for controlled delivery of Ketorolac tromethamine.     

Anticancer drug release from poly(N-isopropylacrylamide/itaconic acid) copolymeric hydrogels

The drug uptake and release of anticancer drug from N-isopropylacrylamide/itaconic acid copolymeric hydrogels containing 0–3 mol% of itaconic acid irradiated at 48 kGy have been investigated. 5-Fluorouracil (5-FU) is used as a model anticancer drug. The effect of 5-FU solution on swelling characteristics of PNIPAAm and P(NIPAAm/IA) copolymeric hydrogels have also been studied. The percent swelling, equilibrium swelling, equilibrium water/5-FU content and diffusion constant values are evaluated for poly(N-isopropylacrylamide) (PNIPAAm) and poly(N-isopropylacrylamide/itaconic) (P(NIPAAm/IA)) hydrogels at 130 ppm of 5-FU solution at room temperature. Diffusion of 5-FU solution into the hydrogels has been found to be the non-Fickian type. Finally, the kinetics of drug release from the hydrogels are examined.     

Radiation Synthesis of Superabsorbent Hydrogels Based on Chitosan and Acrylic Acid for Controlled Drug Release

Superabsorbent hydrogels based on the natural polymer chitosan and acrylic acid (CS/AAc) was prepared using ⁶⁰Co gamma radiation as a source of initiation and crosslinking. The factors, which affect the preparation of CS/AAc hydrogels such as irradiation dose, CS/AAc ratios, and acrylic acid monomer concentrations, to get the best optimum conditions, were investigated. The kinetic studies of the swelling of CS/AAc hydrogel showed that it follows a Fickian type of water diffusion. The Fickian constant value ‘n’ was more than 0.5 with a high swelling capacity of 300 g/g as superabsorbent hydrogel. In addition, the suitability of CS/AAc hydrogel as carrier material for the drug Chlortetracycline-HCl has been investigated by adsorption isotherm studies. The performance of drug release from hydrogel systems, influenced by acrylic acid ratio and the effect of pH of the medium was studied.     

Effect of kappa-carrageenan on the properties of poly(N-vinyl pyrrolidone)/kappa-carrageenan blend hydrogel synthesized by γ-radiation technology

A series of hydrogels in the form of rods were prepared from kappa-carrageenan (KC) and poly (N-vinyl pyrrolidone) (PVP) by gamma radiation with ⁶⁰Co γ source at room temperature. The properties of the prepared hydrogels, such as the gel strength, gel fraction and swelling behavior were investigated. Incorporation of KC into the PVP/water system increased obviously the gel strength and equilibrium degree of swelling (EDS) of PVP hydrogel. The experimental analyses showed that the crosslinking reaction of PVP was quicker than the degradation of KC at a low dose (less than 30 kGy), and the degradation of KC was inhibited in the PVP/KC mixture system. So an interpenetrating polymer network (IPN) hydrogel composed of PVP (a chemical crosslinking network) and KC (a physical crosslinking network) was proposed here. The existence of different classes of water in this IPN system was shown by water melting curves using DCS.     

Synthesis and Properties of IPN Hydrogels Based on Konjac Glucomannan and Poly（acrylic acid）

As a random copolymer of β-(1,4) linked D-mannose and D-glucose, konjac gluco- mannan (KGM) is a naturally occurring water-soluble polysaccharide, and has been paid attention in the field of drug controlled release carriers potentially used in colon1,2. …     

Radiation synthesis of superabsorbent polyethylene oxide/tragacanth hydrogel

A new superabsorbent hydrogel has been prepared from tragacanth and polyethylene oxide (PEO) by gamma radiation at room temperature. Tragacanth solutions with different concentrations (1%, 3% and 5%) have been blended with 5% aqueous solution of PEO at a ratio of 1:1 and irradiated at doses 5–20 kGy. The properties of the prepared composite hydrogels were evaluated in terms of the gel fraction and the swelling behavior. An unexpected growth of the gel fraction was observed in PEO/tragacanth hydrogels irradiated at 5 kGy. Incorporation of 5% tragacanth into the aqueous PEO increased significantly the swelling percent of the hydrogels to more than 14,000% and thus makes it a superabsorbent material.     

Preparation of composites and nanocomposites based on bentonite and poly(sodium acrylate). Effect of amount of bentonite on the swelling behaviour

A series of composite and nanocomposite hydrogels were synthesized by copolymerization reaction of partially neutralized acrylic acid (SA) on bentonite micropowder (BT) using N,N′-methylenebisacrylamide (MBA) as a crosslinker and potassium persulfate (I) as an initiator in aqueous solution. The influences of Na⁺-BT, organoBT (O-BT), and the content of the BT in the copolymeric gels on the swelling behaviour in deionized water and saline solution (0.2 wt.% NaCl_(aq)) were investigated. Results showed that the equilibrium swelling (W_∞) was decreased by adding a small amount of the BT, however, at higher BT contents, the W_∞ increased with the increase of the amount of clay. It was found that a concentration of 14 wt.% Na⁺-BT gave the best results absorption (955 g/g). Moreover, the amount of swelling for these absorbents in saline solution was smaller than that in deionized water. These hydrogels were characterized by X-ray diffraction and scanning electron microscopy. Finally, the thermogravimetric analysis indicated that introduction of clay to the polymer network resulted in an increase in thermal stability.     

壳聚糖-聚丙烯酸复合水凝胶的药物控制释放行为

以壳聚糖(Cs)和丙烯酸(AA)为原料,利用自由基聚合法制备了具有孔洞结构的复合水凝胶Cs-PAA,并研究了AA的量、交联剂的量、聚合温度和AA的中和度对水凝胶溶胀度的影响以及复合水凝胶对烟酸的控制释放。 结果表明,Cs-PAA复合水凝胶具有良好的pH值、离子强度敏感性,且溶胀度最高达1228 g/g,其在pH=686的缓冲溶液中的烟酸累积释放率明显大于其在pH=1.80的缓冲溶液,因此Cs-PAA水凝胶可作为肠口服药物的载体。     

Preparation and properties of diatomite composite superabsorbent

A novel diatomite composite superabsorbent was synthesized by solution polymerization of partially neutralized acrylic acid and diatomite, using N,N′-methylenebisacrylamide as a crosslinking agent and hydrogen peroxide and L -ascorbic acid as a redox initial system. The influences of some reaction conditions, such as diatomite content, neutralization degree of acrylic acid, amount of initiator, amount of crosslinking agent, monomer concentration, and the reaction temperature on swelling characteristic were investigated. The water absorbency of the sample prepared at optimum conditions was 99 g/g in 0.9 wt% NaCl solution. The results of swelling rate measurement showed that diatomite composite superabsorbent had better swelling rate than that of poly(sodium acrylate) prepared in the same conditions. Other properties, i.e. water retention, reswelling ability and resistance to salt, were also examined. Copyright © 2007 John Wiley & Sons, Ltd.     

pH快速响应PNIPAAm-co-PAAc水凝胶的制备及溶胀动力学

pH快速响应PNIPAAm-co-PAAc水凝胶的制备及溶胀动力学;N-异丙基丙烯酰胺;pH敏感性;溶胀历史     

Studies on radiation synthesis of polyethyleneimine/acrylamide hydrogels

Polyethyleneimine(PEI)/acrylamide(AAM) hydrogels were synthesized by γ-radiation-induced polymerization/crosslinking of aqueous mixtures containing different ratios of PEI and AAM. The gel percentage and equilibrium degree of swelling (EDS) of the synthesized hydrogels were investigated. The compositions of the hydrogels produced were found to be different from the feed composition. Ion-chromatography technique was used to determine the amount of Pb (II) and Cd (II) absorbed by the hydrogel. The maximum binding capacity of the PEI/AAM hydrogels, for Pb and Cd was found to be 19 and 12.6 mg/g, respectively, (at 100 ppm). PEI/AAM hydrogels had better metal uptake efficiency than the pure AAM hydrogel at concentrations less than 50 ppm. Pure PEI was observed to be highly degrading type polymer on exposure to gamma radiation. TGA and FT-IR techniques were used to characterize the prepared hydrogels.     

E-beam radiation synthesis of xanthan-gum/carboxymethylcellulose superabsorbent hydrogels with incorporated graphene oxide

In this study the electron beam (e-beam) radiation synthesis in “paste-like condition” and characterization of the network structure of acrylic acid (AA) sodium salt/xanthan gum (XG)/carboxymethylcellulose (CMC) superabsorbent hydrogels incorporating graphene oxide (GO) was investigated. The effects of the AA concentration on gel fraction, sol-gel analysis, swelling degree and network parameters, as well as the relationship between these parameters and radiation dose was also established.

Gel fraction exceeds 90%, and the p₀/q₀ ratio shows a moderate degradation process. The swelling kinetic data were used to determine, first the swelling degree, second the diffusion characteristics, and third the average molecular weight between crosslinks (Mc), as well as. The diffusion data revealed a Fickian mechanism transport, for each hydrogel compositions. The network parameters (Mc and ξ) increased with absorbed dose, while cross-linking density and the radiation-chemical yields were decreased.     

多孔壳聚糖接枝聚丙烯酸/钠基蒙脱土复合高吸水凝胶的制备及其对Pb2+的吸附

以十二烷基苯磺酸钠(SDS)胶束为孔模板,过硫酸铵(APS)引发,N,N'-亚甲基双丙烯酰胺(MBA)交联,壳聚糖(CS)与丙烯酸(AA)、钠基蒙脱土(Na-MMT)在水溶液中接枝共聚,成功制备了多孔壳聚糖接枝聚丙烯酸/钠基蒙脱土(CS-g-PAA/Na-MMT)复合高吸水凝胶,提出了SDS胶束致孔机理。扫描电子显微镜(SEM)分析表明,添加SDS的样品,凝胶表面出现多孔结构。通过考察SDS浓度对复合高吸水凝胶平衡吸水倍率和吸水速率的影响,发现当SDS浓度为1.5 mmol/L时,复合凝胶在蒸馏水和生理盐水中的平衡吸水倍率相对于空白样分别提高53.9%和35.3%,初始溶胀速率常数K_is也由空白样的1.2652 g/(g·s) 提高到5.1680 g/(g·s)。多孔结构也使复合凝胶对Pb²⁺的吸附速率加快,在10 min内即可达到饱和吸附量的95%,30 min完全达到吸附平衡。     

Micrometer scale gel patterns

A novel method for fabricating micrometer sized gel patterns is described. The presented method involves spin-coating a pre-gel solution on a surface that was chemically treated to modulate its surface energy, creating highly hydrophobic areas on a hydrophilic substrate. Following spin-coating, the gel solution self organizes on the hydrophilic sites. This method offers the advantages of high resolution, self-alignment to pre-patterned electrodes, and a simple straightforward fabrication process. Minimum feature size achieved was approximately 20 μm. The characteristic shrinking and swelling times of gel patterns were measured and found to be around 0.6 s for swelling and 2 s for shrinking (for a 60 μm diameter gel) in agreement with the reduced response time expected for scaled down gel patterns. These results suggest the suitability of these gel patterns as valves or actuators in microfluidic devices. Micron-size gel patterns were also incorporated into microfluidic channels thus demonstrating a new approach to create simple, affordable, microfluidic devices, which incorporate “smart” hydrogels as building elements in a simple fashion.     

Preparation and characterization of poly(acrylic acid)‐iron rich smectite superabsorbent composites

A novel poly(acrylic acid)‐iron rich smectite (IRS) superabsorbent composite was synthesized by graft copolymerization reaction of acrylic acid (AA) in the presence of N,N‐methylenebisacrylamide (MBA) as a crosslinker. IRS was used to strengthen the hydrogel products in the polymerization process. Water absorbencies for these superabsorbent composites in water and saline solutions were investigated. IRS caused a reduced equilibrium swelling as low as 8–26%. However, grafted IRS particles resulted in improved gel strength as high as 66% compared to the IRS‐free sample. IRS modified superabsorbent hydrogel composites exhibited higher thermal stability compared to the IRS‐free sample. The pH dependent reversible swelling behavior of hydrogels was also investigated. It is found that the swelling process is pH dependent and reversible for synthesized superabsorbent. Superabsorbent hydrogel composites were characterized by thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). FTIR spectroscopy was confirmed grafting of acrylic chains onto the surface of IRS particles. From the standpoint of these results, these strengthened and thermostabilized hydrogels may be considered as good candidates for a controlled release study and agricultural applications. Copyright © 2007 John Wiley & Sons, Ltd.