Neptunium(III) application in extraction chromatography

This paper describes a novel strategy for actinide separation by extraction chromatography with Np(III) valence adjustment. Neptunium(IV) was reduced to Np(III) using Cr(II) and then selectively separated from uranium (IV) on a TEVA resin. After elution, Np(III) was retained on a DGA resin in order to remove any detrimental chromium impurities. Neptunium(III) formation was demonstrated by the complete and selective elution of Np from TEVA resin (99 ± 7%) in less than 12 mL of 9 M HCl from U(IV) (0.7 ± 0.7%). It was determined by UV–visible and kinetic studies that Cr(II) was the only species responsible for the elution of Np(IV) as Np(III) and that the Cr(II) solution could be prepared from 2 to 30 min before its use without the need of complex degassing systems to prevent the oxidation of Np(III) by oxygen. The methodology proposed here with TEVA/DGA resins provides removal of Cr(III) impurities produced at high decontamination factors (2.8 × 10³ and 7.3 × 10⁴ respectively).     

Electrochemical determination of muscle relaxant drug tetrazepam in bulk form,pharmaceutical formulation,and human serum

Tetrazepam dissolved in the Britton-Robinson universal buffer of various pH values (2.5–11.5) containing 10 vol. % of ethanol was reduced at the mercury electrode in a single 2-electron irreversible step due to reduction of the 4,5 C=N double bond of the seven-membered ring. Differential pulse polarography (DPP) and adsorptive cathodic stripping voltammetry (AdCSV) techniques (Linear sweep LS, differential pulse DP and square-wave SW modes) for quantification of tetrazepam in bulk form and in myolastan tablets are presented. Moreover, the described linear sweep, differential pulse, and square-wave adsorptive cathodic stripping voltammetry was successfully applied in quantification of tetrazepam in spiked human serum without any prior extraction of the drug. The obtained results showed an increased sensitivity of the described electro-analytical procedures for the quantification of tetrazepam in the following order DPP, DP-AdCSV, LS-AdCSV, and SW-AdCSV, since the observed limits of tetrazepam quantitation by these electroanalytical techniques were 5 × 10⁻⁶ mol L⁻¹, 3 × 10⁻⁷ mol L⁻¹, 1 × 10⁻⁸ mol L⁻¹, and 3 × 10⁻⁹ mol L⁻¹, respectively.     

Determination of radiochemical purity of chlormerodrin-203 by electrophoretic method

An electrophoretic method to control the radiochemical purity of chlormerodrin-203 is described. Optimum conditions for the separation of inorganic and organically bound mercury-203 were determined by investigating its mobility in the concentration range of 1·10⁻⁵–1·10⁻² M NaCl. Maximum separation, of²⁰³Hg and hydroxychlormerodrin was achieved at 0.05M NaCl, at the potential gradient of 8V/cm for 2 hrs.     

Solubility of neptunium oxide in the KURT (KAERI Underground Research Tunnel) groundwater

The solubilities of NpO₂(s) in the KURT (KAERI Underground Research Tunnel) granitic groundwater with low ionic strength were measured experimentally and calculated by a geochemical code. Then these results were compared with each other as well as with foreign results. The concentrations of neptunium were measured as 6·10⁻⁸−2·10⁻⁸ mol/L at a pH = 9.5–11.1 and Eh = −0.2 V, and less than 5·10⁻⁹ mol/L at a pH = 11.8–13.0 and Eh = −0.3–0.44 V. The dominant aqueous species were presumed as Np(OH)_x(CO₃)_y ^4−x−2y complexes and Np(OH)₄(aq) at pH = 9.5–13 under the Eh<−0.2 V reducing condition.     

Dosage des thiols par polarographie a impulsions

The determination of thiols has been studied by pulse polarography. A single peak is obtained if the concentration is less than 10^-4 M. The electrochemical reaction involves oxidation of mercury in presence of the thiol with adsorption of the mercury thiolate on the electrode. The method is more sensitive with a negative pulse; this corresponds to reduction of the mercury thiolate formed during the drop life. The sensitivity is about 10^-7 M, i.e. 3 p.p.b. calculated as sulfur. Peak potential values are given for H₂S, nine aliphatic thiols and benzenethiol. Peak height is proportional to concentration up to about 5 · 10^-5 M. The phenomena are more complicated for concentrations higher than 10^-4 M so that the method is not then analytically useful.     

Removal of zinc and mercury ions from aqueous solution by hydrous ceric oxide

The present work deals with study of uptake behavior of zinc and mercury ions by hydrous ceric oxide applying a radiotracer technique. The influence of various parameters such as concentration, temperature and pH have been examined. It was observed that the amount of zinc and mercury ions adsorbed at equilibrium increases with increase of adsorptive concentration (1.0·10⁻⁷ to 1.0·10⁻²M), temperature (303–333K) and pH (ca. 3–10). Concentration dependence data agree well with the classical Freundlich isotherm. The radiation stability of hydrous ceric oxide was also investigated by exposing it to a 11.1 GBq (Ra−Be) source associated with γ-dose of 1.72 Gy·h⁻¹ and also using a⁶⁰Co source (4.66 kGy·h⁻¹). Adsorption of these metal ions in the presence of some monovalent and divalent cations and complexing agents has also been included in the study.     

Pulse radiolytic investigation of the reaction of hydroxyl radicals with gentamycin

Hydroxyl radicals were generated radiolytically in N₂O-saturated aqueous solutions of the aminoglycoside antibiotic, gentamycin. Using the pulse radiolysis technique, the rate constant of OH radicals with gentamycin determined was 1.2·10⁹ dm³·mol⁻¹·s⁻¹. Upon^.OH attack a transient species with an absorption maximum at 270 nm is observed which decays by second-order kinetics within the solute concentration range of 3.2·10⁻⁵ to 1·10⁻³mol·dm⁻³. Transient species undergoes transformation to a permanent product absorbing between 260 and 340 nm with maximum absorption at 300 nm. Rate constant of the reaction of bimolecular decay of gentamycin radicals, k (Gen^.+Gen^.) was found to be ≈ 1.4·10⁷ dm³·mol⁻¹·s⁻¹.     

Studies of the reaction of the hydroxyl radical with the oxalate ion in an acidic aqueous solution by pulse radiolysis

The reaction of the · OH radical with the oxalate ion in an acidic aqueous solution was studied by pulse radiolysis. The rate constant for the reaction of formation of the radical HOOC-COO·(λ_max = 250 nm, ɛ = 1800 L mol⁻¹ cm⁻¹) is (5.0±0.5)·107 L mol⁻¹ s⁻¹. In the reaction with the hydrogen ion (k = 1.1·10⁷ L mol⁻¹ s⁻¹), the radical HOOC-COO· is transformed into a nonidentified radical designated arbitrarily as H⁺(HOOC-COO)· (λ_max = 260 nm, ɛ = 4000 L mol⁻¹ cm⁻¹). Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1165–1167, June, 2008.     

Kinetics of reduction of hexavalent neptunium by nitrous acid in solutions of nitric acid

Nitrous acid is a key redox controlling factor, affecting the speciation of neptunium in the reprocessing of used nuclear fuel by solvent extraction. The kinetics of the reduction of neptunium(VI) by nitrous acid in solutions of nitric acid was investigated spectrophotometrically by the method of initial rates. The reaction is of first order with respect to Np(VI) while the order with respect to HNO₂ is 1.20 ± 0.04. The reaction rate is almost inversely proportional to the hydrogen ion concentration (reaction order −0.92 ± 0.06), indicating that the reaction proceeds primarily through the reaction of neptunium(VI) with the nitrate anion. The experimental value of the rate constant k for the rate law −d[Np(VI)]/dt = k·[Np(VI)]·[HNO₂]^1.2/[H⁺] is of (0.159 ± 0.014) M^−0.2 s⁻¹ in I = 4 M and at 20 °C. The activation energy is (−57.3 ± 1.6) kJ/mol, which is in agreement with previous data on this reaction in perchloric acid.     

Comparison of differential pulse and alternating current polarography in the soft-modelling study of the complexation of Cd(II) by the fragment Cys-Gly and by the phytochelatin (γ-Glu-Cys)<Subscript>2</Subscript>Gly

A comparison of a differential pulse polarographic with a phase sensitive alternating current polarographic study of the Cd-Cys-Gly and Cd-PC₂ systems [PC₂ being a phytochelatin of general structure (γ-Glu-Cys) _n -Gly, with n = 2] has been performed. The chemometric multivariate curve resolution method with alternating least squares was applied in the experimental data analysis. The results obtained by both polarographic techniques have made it possible to find out the formation sequences of the complexes and their final stoichiometries. The alternating current polarograms compared with the differential pulse ones show some differences (a new signal and an important shift of peak potentials), which anyway are consistent with some of the conclusions obtained by differential pulse polarography. This fact implies that although the alternating current polarography results need some corrections before data treatment, they provide extra information that complements the conclusions achieved by differential pulse polarography. Figure Voltammograms at ACP(−10°), ACP(−65°) and corrected ACP during the titration of a 10⁻⁵ mol L⁻¹ Cd(II) solution with PC₂ at pH 8.5 in 0.05 L⁻¹ Tris.     

Electroanalysis and determination of acetaldehyde in fuel ethanol using the reaction with 2,4-dinitrophenylhydrazine

The voltammetric reduction of acetaldehyde was studied in 0.1 M LiOH: LiCl (60: 40 v/v). Well-defined waves can be seen at −1.77 and −1.60 V with the use of hanging mercury and glassy carbon electrodes. Acetaldehyde was shown to react at room temperature with the 2,4-dinitrophenylhydrazine and the product exhibited a differential pulse voltammetric peak at −0.90 V, which was well separated from the peaks of the derivative. This allowed the indirect determination of acetaldehyde in the presence of 0.1 M ethanol/tetrabutylammonium perchlorate after 10 min of reaction. Calibration graphs were obtained for 1.00 × 10⁻⁶−1.00 × 10⁻⁴ M of acetaldehyde. The detection limit is 8.14 × 10⁻⁷ M. The method has been applied satisfactorily to the determination of total aldehyde in fuel ethanol samples without any pretreatment. The text was submitted by the authors in English.     

Adsorptive anodic stripping voltammetry of zirconium(IV)-alizarin red S complex at a carbon paste electrode

A sensitive adsorptive anodic stripping procedure for the determination of trace zirconium at a carbon paste electrode (CPE) has been developed. The method is based on adsorptive accumulation of the Zr(IV)-alizarin red S(ARS) complex onto the surface of the CPE, followed by oxidation of adsorbed species. The optimal experimental conditions include the use of 0.10 mol · L⁻¹ ammonium acetate buffer (pH 4.3), ARS, an accumulation potential of 0.20 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV · s⁻¹ and a second-order derivative linear scan mode. The oxidation peak for the complex appears at 0.69 V. The peak current is proportional to the concentration of Zr(IV) over the range of 1.0 × 10⁻⁹–2.0 × 10⁻⁷ mol · L⁻¹, and the detection limit is 3 × 10⁻¹⁰ mol · L⁻¹ for a 2 min adsorption time. The relative standard deviations (n = 8) for 5.0 × 10⁻⁸ and 5.0 × 10⁻⁹ mol · L⁻¹ Zr(IV) are 3.3 and 4.8%, respectively. The proposed method was applied to the determination of zirconium in ore samples with satisfactory results.     

Determination of Methimazole and Carbimazole Using Polarography and Voltammetry

Abstract

Anodic waves of methimazole (I) (1-methylimidazole-2-thiol) and carbimazole (II) (1-ethoxycarbonyl-3-methyl-2-thio-4-imidazoline) on mercury electrodes correspond to mercury salt formation. Both compounds form in the thiono form a soluble complex at pH < 6, compound (I) at higher pH-values a slightly soluble salt of the thiol form. Electrode processes involving the thiol form are complicated by adsorption. Oxidation at solid electrodes occurs only at potentials more than 0.5 V more positive. For compound (I) spectrophotometry indicated pK_a=12.0 ± 0.2. By d.c. polarography in 0.1 M H₂SO₄ containing 10% ethanol the determination of both compounds is possible between 4 × 10^? and 1 × 10^?3 M, by differential pulse polarography between 1 × 10^? and 1 × 10^?4 M, by differential pulse voltammetry at HMDE between 5 × l0^?7 and 6 × 10^? M.     

Electrochemical Reduction of Benzaldehyde as its Girard-P Derivative at the Mercury Electrode and Differential-Pulse Polarographic Determination of Benzaldehyde

 The polarographic behaviour of benzaldehyde as its Girard-P derivative was studied using various electrochemical techniques and a method for the determination of benzaldehyde (10⁻⁶ − 8 × 10⁻⁵ M) by differential-pulse polarography, based on the in situ formation of its Girard-P derivative in aqueous solution at pH 2.5, is proposed. The relative standard deviation was 1.7% (ten determinations at the 5 × 10⁻⁵ M level). The applicability of this method is checked in benzyl alcohol and synthetic samples containing, o-aminophenol, 2-amino pyridine, o-cresol, amylic alcohol, salicylic acid, 4-aminobenzoic acid and naphthalene sulfonic acid. Received April 6, 2000. Revision February 13, 2001.     

An electroanalytical study of the anticancer drug dacarbazine

The electrochemical behaviour of dacarbazine [5-(3,3-dimethyl-1-triazenyl) imidazole-4-carboxamide; DTIC] was investigated by Tast and differential pulse polarography (d.p.p.) at the dropping mercury electrode, by cyclic and differential pulse voltammetry at the hanging mercury drop electrode and by anodic voltammetry at the glassy carbon electrode. Calibration graphs were obtained for 2×10^?8?2×10^?5 M DTIC by d.p.p., for 5×10^?9?1×10^?5 M by adsorptive stripping voltammetry ar a hanging mercury drop electrode, and for 1?10×10^?5 M by high-performance liquid chromatography with oxidative amperometric detection at a glassy carbon electrode. The methods are compared and applied to determine DTIC added to blood serum after a simple clean-up procedure.     

Rapid photometric determination of neptunium with xylenol orange after extraction with Aliquat-336

A rapid method based on the extraction of neptunium(IV) by Aliquat-336 followed by its direct photometric determination in the organic phase employing xylenol orange is reported. Optinum conditions have been established for the extraction and determination of as little as 0.4 ppm of Np. The molar absorptivity of the red-coloured neptunium complex at 535 nm is 49535±361 1·mol⁻¹·cm⁻¹. Unlike the well-known absorptimetric method for estimating NP(IV) with Arsenazo III, this method tolerates many-fold excesses of fluoride, nitrite, nitrate, phosphote, oxalate as well as UO ₂ ²⁺ , Pu⁴⁺, Zr⁴⁺, etc., which are some of the major contaminants associated with neptunium during its reprocessing.     

Determination of heavy metals and iodide by stripping voltammetry in sodium chloride on mercury-graphite electrodes

The behavior of Cd(II), Pb(II), Cu(II), and I⁻ in the aqueous solutions of sodium chloride is studied by stripping voltammetry. A new version of using an indicator electrode from carbon glass ceramics modified with mercury for the consecutive stripping determination of Cd(II), Pb(II), Cu(II), and iodide is proposed. The mercury-graphite electrode was formed in the solution of a supporting electrolyte based on NH₄Cl, HCl, 0.05 M potassium tetraoxalate (KH₃C₄O₃ · 2H₂O), and 5 × 10⁻⁵ M mercury(II). At first, Cd(II), Pb(II), Cu(II), and then iodide were determined by anodic-cathodic stripping voltammetry after adding a sample solution (table salt, 10–100 mg/mL NaCl).     

Separation of15N by chemical exchange in NO, NO2−HNO3 system under pressure

The basic isotopic exchange reaction is responsible for the separation of¹⁵N in the Nitrox system that between gaseous nitrogen oxides and aqueous nitric acid with a single stage separation factor α=1.055 for 10M nitric acid, at 25°C and atmospheric pressure takes place. In order to know what happens in¹⁵N separation at higher pressure, when the isotopic transport between two phases is improved, a stainless steel laboratory experimental plant with a 1000 mm long × 18 mm i.d. column, packed with triangular wire springs 1.8×1.8×0.2 mm², was utilised. At 1.5 atm (absolute), and 2.36 ml·cm⁻²·min⁻¹ flow rate HETP was 7% smaller than at atmospheric pressure and 1.5 times smaller flow rate. HETP at 3.14 ml·cm⁻²·min⁻¹ flow rate and 1.8 atm is practically equal with that obtained at atmospheric pressure and 2 times smaller flow rate. The operation of the¹⁵N separation plant at 1.8 atm (absolute), instead of atmospheric pressure, will permit doubling of the 10M nitric acid flow rate and of¹⁵N production of the given column.     

Determination of azinphos-ethyl insecticide by adsorptive stripping voltammetry on the hanging mercury-drop electrode

The electrochemical characteristics of azinphos-ethyl (APE) have been determined by means of electrochemical techniques such as cyclic voltammetry (CV) and adsorptive stripping voltammetry (ASV) at a hanging mercury drop electrode (HMDE) over a wide range of pH from 2.0 to 8.0. The cyclic voltammograms demonstrate the adsorption of this compound at the mercury electrode. A systematic study of the various operational parameters that affect the stripping response was carried out by differential pulse voltammetry (DPV). With a preconcentration potential of −0.6 V and a 60 s preconcentration time, the limit of detection was 5.42 × 10⁻⁹ M, and the relative standard deviation (n = 5) was 2.7 % at concentration level of 6.45 × 10⁻⁷ M APE. The degree of interference from diverse ions and some other pesticides on the differential pulse stripping signal for APE was evaluated. Finally, the method was applied to the determination of APM in spiked soil, tap water, and treated wastewater. The text was submitted by the author in English.     

Synthesis,structure and properties of complex compounds of cobalt,nickel, copper and zinc with 2-formylpyridine semicarbazone

2-Formylpyridine semicarbazone L reacts with cobalt, nickel, copper and zinc chlorides, nitrates and perchlorites to form coordination compounds of compositions ML₂X₂·nH₂O (M=Co, Ni, Cu, Zn; X = Cl, NO₃, ClO₄; L = NC₅H₄-CH=N-NH-C(O)-NH₂; n = 0, 1) and CuLX₂·nH₂O (X = Cl, Br, NO₃; n = 0−0.5). Complex CuL(NO₃)₂ has polynuclear, CuLX₂·0.5H₂O (X = Cl, Br), binuclear, and other compounds, mononuclear structures. Azomethine L behaves in them as tridental N,N,O-ligand. Thermolysis of these complexes proceeds through such stages as dehydration (80–95°C), deactivation (145–155°C) and complete theral degradation (170–590°C). Complexes CuLX₂·nH₂O (X = Cl, NO₃; n = 0−0.5) were established to inhibit in vitro the growth and reproduction of 100% of cancer cells of human mieloid leukaemia HL-60 at 10⁻⁴ M concentration. At 10⁻⁵ M concentration they inhibit only 10% of cells, and at 10⁻⁶ M concentration they do not possess anticancer activity.