A polyaniline-magnetite nanocomposite as an anion exchange sorbent for solid-phase extraction of chromium(VI) ions

This work describes a novel polyaniline-magnetite nanocomposite and its application to the preconcentration of Cr(VI) anions. The material was obtained by oxidative polymerization of aniline in the presence of magnetite nanoparticles. The parameters affecting preconcentration were optimized by a Box-Behnken design through response surface methodology. Extraction time, amount of magnetic sorbent and pH value were selected as the main factors affecting sorption. The sorption capacity of the sorbent for Cr(VI) is 54 mg g⁻¹. The type, volume and concentration of the eluents, and the elution time were selected as main factors in the optimization study of the elution step. Following sorption and elution, the Cr(VI) ions were reacted with diphenylcarbazide, and the resulting dye was quantified by HPLC with optical detection at 546 nm. The limit of detection is 0.1 μg L⁻¹, and all the relative standard deviations are <6.3 %. The nanocomposite was successfully applied to the rapid extraction and determination of trace quantities of Cr(VI) ions in spiked water samples.

A schematic procedure of magnetic solid phase extraction

     

Polyaniline-coated Fe(3) O(4) nanoparticles: An anion exchange magnetic sorbent for solid-phase extraction

In this study, the capability of the prepared polyaniline-coated Fe(3) O(4) nanoparticles for magnetic solid-phase extraction of three parabens from environmental wastewater, cream, and toothpaste samples is presented. Synthesized Fe(3) O(4) nanoparticles were coated with sulfate-doped polyaniline via polymerization of aniline in the presence of Fe(3) O(4) nanoparticles and sulfuric acid. Here, polyaniline-coated Fe(3) O(4) nanoparticles are presented as anion exchange sorbent, which extract anionic form of parabens via anion exchange with dopant of polyaniline. The experimental conditions affecting extraction efficiency were further studied and optimized. The experimental results showed that maximum extraction efficiency can be obtained at 70 mL sample solution of pH 8, extraction and desorption times of 2 and 1 min, respectively, 100 μL of 3% (v/v) acetic acid in acetonitrile as eluent, and 100 mg of the adsorbent. Under these conditions, the linear dynamic ranges were 0.5-100 μg/L with good correlation coefficients (0.998-0.999). The detection limits were in the range of 0.3-0.4 μg/L and the relative standard deviations were less than 2.4 (n = 5) for the three parabens. Finally, this fast and efficient method was further employed for determination of target analytes in cream, toothpaste, and environmental wastewater samples and satisfactory results were obtained.     

Solvent extraction of chromium(VI) from base metal ions with diphenyl-2-pyridylmethane as a liquid anion exchanger

The extraction of chromium(VI) from aqueous hydrochloric, nitric and sulfuric acid solutions by diphenyl-2-pyridylmethane(DPPM) dissolved in chloroform has been studied. Chromium(VI) is quantitatively extracted from hydrochloric acid solutions in the range 0.1–1M. With increasing acid concentration, the extraction of chromium diminishes and in concentrated acid solutions practically all the chromium remains in the aqueous phase. The quantitative back-extraction of chromium from the organic phase is possible with HCl or HNO₃ at concentrations higher than 5M through the use of reducing agents. The composition of the extracted chromium(VI) species was studied in solution. The complexes (DPPMH)⁺HCrO ₄ ⁻ and (DPPMH)₂Cr₂O ₇ ⁻ are extracted for tracer and macro amounts of chromium(VI) respectively. The data have been utilized for the separation of chromium(VI) from base metal ions.     

Magnetic dispersive solid-phase extraction of some polycyclic aromatic hydrocarbons from honey samples using iron (III) oxinate nanocomposite as an efficient sorbent

In this work, iron (III) oxinate magnetic nanocomposite was synthesized and employed as an efficient sorbent for the magnetic dispersive solid-phase extraction of some polycyclic aromatic hydrocarbons from honey samples. In the following, dispersive liquid–liquid microextraction procedure was used for further preconcentration of the analytes. The prepared sorbent was characterized using Fourier transform infrared spectrophotometry, X-ray diffractometry, vibrating sample magnetometry, energy dispersive X-ray spectroscopy, and scanning electron microscopy. The results verified the successful formation of the magnetic sorbent. In the extraction process, the sorbent was added into an aqueous solution and the mixture was vortexed. After completing the adsorption process, the supernatant phase was separated in the presence of a magnet and the analytes adsorbed onto sorbent were eluted by acetonitrile. Then, microliter-level 1,1,1–trichloroethane was mixed with the obtained acetonitrile and injected into NaCl solution. Finally, one microliter of the sedimented phase was injected into gas chromatography-flame ionization detector after centrifugation. Under the optimum conditions, a great repeatability (relative standard deviation equal or less than 5 and 6% for intra– and interday precisions, respectively), acceptable extraction recoveries (59–84%), high enrichment factors (118–168), and low limits of detection and quantification (0.16–0.36 and 0.56–1.22 ng/g, respectively) were acquired.     

Method for the determination of chromium (VI) as chromium (VI)-dibenzyidithiocarbamate

Dibenzyldithiocarbamic acid (DBDC) exhibits the ability to speciate between chromium(VI) and chromium(III), since only the chromium(VI) will form complexes with DBDC. The complex is then extracted into an organic solvent and assayed using an ultraviolet-visible (UV-VIS) spectrophotometer at 498.8 nm. Using 250 ml of aqueous sample detection limits less than 1 ng/ml are possible, while the linear range extends to 500 gmg/ml when working at 498.8 nm. Oxidation of the chromium(III) to chromium (VI) using cerium (IV) enables the determination of total chromium and subsequently the chromium (III) in solution. Evaluation of the method with a standard reference material produced only 4.81 part per thousand error in the determination of chromium(VI).     

Poly(methyloctylsiloxane) immobilized on silica as a sorbent for solid-phase extraction of some pesticides

A laboratory-made sorbent for solid-phase extraction (SPE) was obtained by thermal immobilization of poly(methyloctylsiloxane) (PMOS) onto silica. Cartridges packed with the new sorbent were used for the simultaneous determination of imazethapyr, nicosulfuron, diuron, linuron and chlorimuron-ethyl in water. These pesticides were separated and quantified using high-performance liquid chromatography with diode array detection (HPLC-DAD). The recoveries achieved with the laboratory-made PMOS cartridges were compared with those of some commercially available silica-based and polymer-based cartridges having C18, C8 and NH(2) pendant groups. Method validation using the laboratory-made sorbent was performed for the five pesticides at three fortifications levels (1x, 2x and 10x the limit of quantification of each pesticide). The laboratory-made PMOS cartridge has low cost preparation and showed good recoveries (72-111%) for all pesticides. Repeatability and intermediate precision were lower than 15%. Its performance was similar or even better, in some cases, than those of the commercial cartridges.     

St-DVB基质阳离子交换固相萃取填料的研制及应用

以玉米淀粉为分散剂,偶氮二异丁腈 (AIBN)为引发剂,二乙烯基苯(DVB)为交联剂,在在氮气保护下,用悬浮聚合法制备了交联苯乙烯-二乙烯苯(St-DVB )高分子微球,用浓硫酸进行磺化,制成了以St-DVB为基质的阳离子交换固相萃取填料.考察了搅拌速度对交联聚苯乙烯微球粒径大小及分布的影响.分别用TEM,SEM/ED...     

Specific extraction of chromium(VI) using supercritical fluid extraction

In some situations, it is no longer sufficient to give a total concentration of a metal. Instead, what is required to understand the potential toxicity of a sample is the concentration of metal species or oxidation state. When developing species specific methods, the major concern is that the integrity of the species ratio is not changed. In other words, the sample preparation or the analytical method will not convert metal ions from one oxidation state to another. Normal extraction techniques and chromatography methods have shown some tendencies to change species ratios. An ideal extraction method would extract the metal efficiently while retaining the metal's oxidation state. The properties of supercritical fluids should approach the ideal of retention of oxidation states. For example, the need for speciation of chromium is obvious since Cr(III) is considered an essential element while Cr(VI) is thought to be toxic and carcinogenic. This paper presents the results of a species specific extraction of Cr(VI) using two different carbamate derivatives as the chelator. Supercritical fluid extraction (SFE) coupled with a fluorinated dithiocarbamate and a methanol modifier allows extraction of 1 ppm Cr(VI) from a solid matrix with a recovery level of 88.4+/-2.57% using the NIST standard sample. The optimized conditions using the HP 7680 supercritical fluid extractor were: 0.1 ml of methanol, 0.05 ml of pure water, and 0.01 g of chelate via a saturation chamber.     

Determination of trace chromium(VI) in drinking water using X-ray fluorescence spectrometry after solid-phase extraction

A new, simple, and selective method for preconcentration and determination of Cr(VI) in aqueous samples. After adsorption in “batch mode” on Aliquat 336-AC, determinations were made directly on the solid by X-ray fluorescence spectrometry, which had the advantage of not requiring the step of elution of the chromium retained. The enrichment factor was calculated considering that the tablets obtained from 10 mL solution of Cr(VI) (1000 μg L^-1) had a final thickness of 0.64 mm and a diameter of 16.7 mm; the volume deposited on the pellet was 0.14 cm³. The preconcentration factor obtained was 71-fold, which was highly satisfactory for chromium trace analysis by XRF. Finally, the method was successfully applied to the determination of Cr(VI) in drinking water samples.     

Evaluation of carbon nanocones/disks as sorbent material for solid-phase extraction

The potential of carbon nanocones/disks as sorbent material in solid-phase extraction (SPE) procedures has been evaluated. For this aim, a model analytical problem, the determination of chlorophenols in water samples, was selected. An accurately weighed amount of 20 mg of purified carbon nanocones/disks was packed in 3 mL commercial SPE cartridges. Once conditioned, up to 8 mL of water samples can be preconcentrated without analyte losses. The chlorophenols were eluted by using 200 μL of hexane. Aliquots of 2 μL of the organic extract were injected in the gas chromatograph–mass spectrometer for separation and quantification. The purification of the commercial nanocones/disks to reduce the presence of amorphous carbon has been successfully achieved by heating the carbon nanocones/disks at 450 °C for 20 min. Detection limits of chlorophenols were in the range 0.3–8 ng mL⁻¹ by using 2 mL of sample. Moreover, excellent average recovery values (98.8–100.9%) have been obtained after the analysis of water samples from different nature. Finally, the performance of the carbon nanocones/disks as sorbent material has been compared with that of multiwalled carbon nanotubes, providing the former better results under the experimental conditions assayed.     

Consecutive sorption of molybdenum(VI) and chromium(VI) from a single sample onto fiber materials filled with an anion exchanger and their solid-phase determination with phenylfluorone and diphenylcarbazide

We have considered the possibility of the sorption-spectrometric determination of molybdenum(VI) with phenylfluorone and chromium(VI) with diphenylcarbazide from a single sample by consecutive sorption from different media onto fiber materials filled with an AV-17 anion exchanger. The dependences of analytical signals of molybdenum and chromium on the sorption conditions (pH of the initial solution, NaCl concentration, sizes of the support disc, agitation time) have been studied in the batch mode. The conditions of analytical signal registration have been determined and the analytical ranges have been established (0.01–0.06 μg/mL for Cr and 0.02–0.2 μg/mL for Mo). It has been demonstrated that molybdenum and chromium can be determined at their ratios from 1: 1 to 5: 1 from a single sample after chromium sorption from 0.1 M HCl and molybdenum sorption at pH 4 by diffuse-reflection spectroscopy or visual test. The selectivity of molybdenum and chromium determination in the presence of interfering ions has been studied.     

Highly integrated flow assembly for automated dynamic extraction and determination of readily bioaccessible chromium(VI) in soils exploiting carbon nanoparticle-based solid-phase extraction

An automated dynamic leaching test integrated in a portable flow-based setup is herein proposed for reliable determination of readily bioaccessible Cr(VI) under worst-case scenarios in soils containing varying levels of contamination. The manifold is devised to accommodate bi-directional flow extraction followed by processing of extracts via either in-line clean-up/preconcentration using multi-walled carbon nanotubes or automatic dilution at will, along with Cr(VI) derivatization and flow-through spectrophotometric detection. The magnitude of readily mobilizable Cr(VI) pools was ascertained by resorting to water extraction as promulgated by current standard leaching tests. The role of carbon nanomaterials for the uptake of Cr(VI) in soil leachates and the configuration of the packed column integrated in the flow manifold were investigated in detail. The analytical performance of the proposed system for in vitro bioaccessibility tests was evaluated in chromium-enriched soils at environmentally relevant levels and in a standard reference soil material (SRM 2701) with a certified value of total hexavalent chromium. The automated method was proven to afford unbiased assessment of water-soluble Cr(VI) in soils as a result of the minimization of the chromium species transformation. By combination of the kinetic leaching profile and a first-order leaching model, the water-soluble Cr(VI) fraction in soils was determined in merely 6 h against >24 h taken in batchwise steady-state standard methods.     

Aptamer-targeted magnetic nanospheres as a solid-phase extraction sorbent for determination of ochratoxin A in food samples

A sorbent based on the aptamer for ochratoxin A was immobilized onto magnetic nanospheres (MNS) and used to develop a magnetic solid-phase extraction procedure to clean up food samples in conjunction with high-performance liquid chromatography separation and fluorescence detection. Specific retention of ochratoxin A by the sorbent was demonstrated, and the capacity of the MNS-aptamer sorbent was determined. The efficacy of this new approach was successfully evaluated through comparison with solid-phase extraction on commercial C18 cartridge. Several different food samples fortified in the range of with 2.5-50 μg/kg yielded mean recoveries from 67% to 90%, respectively. Finally, this oligosorbent was applied to the selective extraction of ochratoxin A from unfortified food samples.     

A magnetic knitting aromatic polymer as a new sorbent for use in solid-phase extraction of organics

Magnetic knitting aromatic polymers (Fe₃O₄/KAPs) are introduced here as a new kind of sorbents. KAPs are hyper-cross-linked-polymers that were prepared via a Friedl-Crafts reaction from triphenylphosphine and benzene as building blocks. The Fe₃O₄/KAP composite was obtained by coprecipitation of KAP with magnetite nanoparticles. The resulting Fe₃O₄/KAP is shown to be a viable magnetic sorbent for various organic materials such as the phenylurea herbicides (PUHs), including metoxuron, monuron, chlortoluron, monolinuron and buturon, and also for various phthalates, polycyclic aromatic hydrocarbons and chlorophenols. The Fe₃O₄/KAP was characterized by means of Brunauer-Emmett-Teller surface area measurements, Fourier-transform infrared spectroscopy, thermogravimetry, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Following desorption with acetonitrile, the analytes were quantified by using HPLC with UV detection. The effects of adsorbent dosage, extraction time, sample pH, ionic strength, desorption solvent and desorption time were optimized for the PUHs. Under optimal conditions, response is linear from 0.5–1.0 up to 50 ng·mL^?1 for the five PUHs. Lower limits of detection range between 0.05 and 0.30 ng·mL^?1. Other figures of merit include (a) high enrichment factors (60–297), (b) good recoveries (91.8–106.5%), and (c) relative standard deviations of <8.4%. The method was successfully applied to analysis of the PUHs in real samples (bottled mixed juice, milk and soymilk). The results indicate that such Fe₃O₄/KAPs have a wide application scope as an adsorbent for use in magnetic solid phase extraction.

Open image in new window

Graphical abstract A magnetic knitting aromatic polymer based nanocomposite (Fe₃O₄/KAP) was prepared by a one-pot method and explored as an absorbent for magnetic solid-phase extraction (MSPE) of phenylurea herbicides (PUHs) from bottled mixed juice, milk and soymilk samples before quantitation by HPLC with UV detection.

     

Hydrogen chromate PVC matrix membrane sensor for potentiometric determination of chromium(III) and chromium(VI) ions

A novel potentiometric Cr(6+) PVC matrix membrane sensor incorporating nickel tris(1,10-bathophenanthroline) hydrogen chromate as an electroactive material and 2-nitrophenyl phenyl ether as solvent mediator is described. In a phosphate buffer solution of pH 5, the sensor displays a rapid and linear response for Cr(6-) over the concentration range 2 x 10(-2)-8 x 10(-6) M with an anionic slope of 55.5 +/- 0.2 mV decade(-1) and a detection limit of the order of 0.4 microg ml(-1). The sensor is used for sequential determination of Cr(6+) and Cr(3+) by direct monitoring of Cr(6+) followed by oxidation of Cr(3+) and measurement of the total chromium. The average recoveries of Cr(3+) and Cr(6+) at concentration levels of 0.5-50 microg ml(-1) are 98.1 +/- 0.4% and 99.1 +/- 0.4% respectively. Redox and precipitation titrations involving Cr(6+) as a titrant are monitored with the sensor. Cr(3+) and/or Cr(6+) in wastewaters of some industries (e.g., leather tanning, electroplating, aluminum painting) and the chromium contents of some alloys and refractory bricks are assessed. The results agree fairly well with data obtained using the standard diphenylcarbazide spectrophotometric method.     

Selective solvent extraction of chromium(VI) using 2-hexylpyridine

The extraction behaviour of trace and macroamounts of chromium(VI) from different mineral acid solutions by 2-hexylpyridine in chloroform has been investigated. In the chloride system, the extracted species is apparently (HPyH⁺)₂ (Cr₂O₇)²⁻ or HPy⁺(HCrO ₄ ⁻ ) for macro and trace amounts of chromium(VI), respectively. Among the common anions chloride and sulphate have little effect on extraction up to 1M concentration, while in the case of nitrate there is a continuous decrease in the extraction with the increase of salt concentration in the aqueous phase. The effect of ascorbate, acetate, citrate, oxalate, thiosulphate, thiocyanate ions on the extraction from 1M HCl was also examined. Separation factors of several elements relative to chromium(VI) have been described and the separation of chromium(IV) from a large number of elements has been achieved.     

Studies on the extraction of chromium(VI) by ketones

A study of the extraction of chromium(VI) from aqueous media by ketones was made. Extraction of chromium was found to be most efficient from aqueous hydrochloric acid solutions. A mechanism for the extraction of chromium(VI) from aqueous hydrochloric acid solutions by methyl isobutyl ketone is proposed involving the formation of a receptor in the organic phase, the exchange of the chloride ion of the receptor for the anionic chromium(VI) species of the aqueous phase, and the solvation of the extracted chromium species. The differences in the abilities of various ketones to extract chromium(VI) from aqueous hydrochloric acid solutions, and the differences in the extraction of chromium (VI) from various aqueous acids by methyl isobutyl ketone are attributed to the differences in the formation of receptors.     

Spectrophotometric determination of chromium(VI) as dichromate after extraction with the pentamethylene-bis(triphenylphosphonium) cation

Chromium(VI) (0–100 μg) can be determined spectrophotometrically at 365 nm after its extraction as pentamethylene-bis(triphenylphosphonium) dichromate into 1,2-dichloroethane. The system is applied to the determination of chromium in a range of steels.