Sandbed Consolidation with Mineral Precipitation

A new method has been developed to prevent sand reentrainment during oil production from unconsolidated or poorly consolidated reservoir formations. Consolidation of the zformation around the well is achieved through in situ precipitation of a sparingly soluble salt, namely, calcium phosphate. Control of the depth of salt formation is achieved by alternating injection, mixing, and reaction of two aqueous solutions of calcium chloride and potassium phosphate. Calcium phosphate crystals precipitate and grow on the grain surfaces, forming sufficiently uniform coatings. The formation of relatively uniform coatings on the grains causes an acceptably small decrease of the permeability, which is a feature of primary importance for oil production. The grains are gradually "cemented" with bridges of calcium phosphate crystallites and form a consolidated and still porous structure. As a result, the rate of hydrocarbon production for the problematic reservoir can be increased considerably without undesirable reentrainment of sand. The proposed method for consolidation has been successfully tested in sandbeds. Several series of experiments have been carried out under diverse conditions to establish the optimum parameter values for the implementation of this method. A set of optimum conditions at 25 degrees C were determined and these conditions gave satisfactory consolidation with permeability loss of ca. 60% of the initial value. The conditions of precipitation were chosen so that the precipitated phase was octacalcium phosphate [Ca(4)H(PO(4))(3).2.5H(2)O], along with its byproduct hydroxyapatite [Ca(5)(PO(4))(3)OH]. Experiments were also carried out at 70 degrees C and have shown that it is feasible to consolidate loose sandpacks at oil reservoir conditions. Copyright 2000 Academic Press.     

Heterogeneous nucleation and growth of calcium carbonate on calcite and quartz

The precipitation of calcium carbonate as a binding salt for the consolidation of loose sand formations is a promising approach. The heterogeneous nucleation and growth of calcite were investigated in supersaturated solutions. The ionic activities in the solutions tested were selected so that they included both supersaturations in which crystal growth took place only following the introduction of seed particles and supersaturations in which precipitation occurred spontaneously past the lapse of induction times. In the latter case the supersaturation conditions were sufficiently low to allow the measurement of induction times preceding the onset of precipitation. The stability domain of the calcium carbonate system was established at pH 8.50, 25 degrees C, measuring the induction times in the range between 30 min and 2 h. The rates of precipitation following the destabilization of the solutions were measured from the pH and/or concentration-time profiles. The induction times were inversely proportional and rates proportional to the solution supersaturation as expected. The high-order dependence of the rates of precipitation on the solution supersaturation suggested a polynuclear growth mechanism. Fitting of the induction time-supersaturation data according to this model yielded a value of 64 mJ/m2 for the surface energy of the calcite nucleus. In the concentration domain corresponding to stable supersaturated solutions, seeded growth experiments at constant supersaturation showed a second-order dependence on the rates of crystal growth of calcite seed crystals. Inoculation of the stable supersaturated solutions with quartz seed crystals failed to induce nucleation. Raising supersaturation to reach the unstable domain showed interesting features: calcite seed crystals yielded crystal growth kinetics compatible with the polynuclear growth model, without any induction time. The presence of quartz seed crystals reduced the induction times and resulted in nucleation in the bulk solution. The kinetic data in the latter case were consistent with the polynuclear growth model and the surface energy for the newly forming embryo was calculated equal to 31.1 mJ/m2, because of the dominantly heterogeneous nature of the process.     

Effect of phosvitin on the nucleation and growth of calcium phosphates in physiological solutions

The promoting effect of phosvitin on the nucleation of hydroxyapatite (HAP) and the inhibitory effect of phosvitin on the transformation from amorphous calcium phosphate (ACP) to HAP were investigated. Atomic force microscopy observations showed that the nucleation of HAP on collagen substrate was greatly enhanced when the phosvitin was bound on the collagen surface. Nucleated crystals were uniformly distributed with a high nucleation rate on the collagen surface in the presence of phosvitin, while, in the absence of phosvitin, crystals nucleated slowly and were observed only at some particular area. Time-resolved static light scattering measurements revealed that the transformation from ACP to HAP was inhibited when free phosvitin was present in the calcium phosphate solutions. The transformation kinetics in the absence of phosvitin, which is a direct reconstruction of the inner ACP structure to HAP, was changed to heterogeneous growth of HAP on ACP with time.     

The effect of polyacrylic acid and reaction conditions on nanocluster formation of precipitated calcium carbonate on microcellulose

The precipitation of micro- and nanoparticles of calcium carbonate onto lignocellulosic microfibers was investigated at different microfiber concentrations with and without polyacrylic acid (PAA), i.e. a polymer commonly used to form polymer-induced liquid precursors of CaCO₃. Concentrations of PAA, Ca(OH)₂, CO₂ and microfiber were varied in order to study the impact of reaction conditions on PCC formation in a batch reactor operated at ambient temperature. High resolution scanning electron micrographs of the samples show that both microfiber concentration and PAA dosage affected the nucleation and crystal growth of PCC filler on cellulosic fiber. Interestingly, at higher microfiber concentrations, larger amount of nano-sized spherical crystals were formed on the microfibers. A higher dosage of PAA, on the other hand, resulted in less nucleation on the microfiber, suggesting a preferential bulk nucleation mechanism. A higher concentration of PAA during the precipitation also led to the formation and stabilization of amorphous CaCO₃, which was supported by SEM images and XRD analysis (lack of characteristic crystal structure).     

Calcium sulfate precipitation in the presence of water-soluble polymers

The effect of four different polymers on the precipitation of calcium sulfate was investigated in the present work. The degree of inhibition was estimated from measurements of the calcium ion activity and from specific solution conductivity measurements in the supersaturated solutions during the course of the precipitation process. The effects of polyacrylic acid (PAA, three different polymers with average molecular weight 2000, 50,000, and 240,000, respectively) and of a co-polymer of PAA with polystyrene sulfonic acid (PSA, average molecular weight<20,000) were investigated with respect to their effect on the kinetics of spontaneous precipitation of calcium sulfate salts. The results of the kinetics experiments suggested that the spontaneous precipitation from supersaturated calcium sulfate solutions at 25 degrees C yielded exclusively calcium sulfate dihydrate (gypsum) both in the absence and in the presence of the polymeric additives. The induction times, preceding the formation of the solid increased in all cases in the presence of the polymeric additives. Polymer concentrations as low as 2.0 ppm increased induction time from practically zero to 10 min. The rates of precipitation were reduced according to the solutions content in the polymers added and precipitation was completely suppressed in the presence of 6.0 ppm of the polymers tested, depending on their molecular weight. The lower the molecular weight of PAA, the more efficient was the threshold inhibition and the stronger the reduction of the rates of spontaneous precipitation. PSA yielded the poorest inhibition efficiency in comparison with the PAA, possibly because of the relatively lower affinity of the sulfonate groups for the calcium ions of the surface of the solid forming. The kinetics results analysis assuming Langmuir-type adsorption of the polymeric molecules on the growing supercritical gypsum nuclei showed different affinity for the polymers tested in agreement with the respective inhibition efficiency, in the order: PAA1>PAA2>PSA>PAA3. The presence of the polymers in the supersaturated solutions resulted in modification of the precipitated gypsum crystals morphology.     

Biomimetic mineralization of hydroxyapatite crystals on the copolymers of vinylphosphonic acid and 4-vinilyimidazole

In the present work, copolymers of vinylphosphonic acid and 4-vinilyimidazole (poly(4-VIm-co-VPA)) were found to be substrates favoring the precipitation of nanohydroxyapatite (HAP) crystals from stable supersaturated solutions at pH 7.4 and 37 degrees C. Deposition kinetics were studied by the constant composition technique. The rates of crystallization both on HAP seed crystals as reference and on the copolymer in powder form were investigated at constant supersaturation conditions. The rates of HAP crystal growth on the polymeric substrate were found to depend on the amount of seed material and on the phosphate content of the copolymer.     

Polyelectrolyte blend multilayer films: surface morphology, wettability, and protein adsorption characteristics

We report the influence of polyelectrolyte (PE) multilayer films prepared from poly(styrene sulfonate)-poly(acrylic acid) (PSS-PAA) blends, deposited in alternation with poly(allylamine hydrochloride) (PAH), on film wettability and the adsorption behavior of the protein immunoglobulin G (IgG). Variations in the chemical composition of the PAH/(PSS-PAA) multilayer films, controlled by the PSS/PAA blend ratio in the dipping solutions, were used to systematically control film thickness, surface morphology, surface wettability, and IgG adsorption. Spectroscopic ellipsometry measurements indicate that increasing the PSS content in the blend solutions results in a systematic decrease in film thickness. Increasing the PSS content in the blend solutions also leads to a reduction in film surface roughness (as measured by atomic force microscopy), with a corresponding increase in surface hydrophobicity. Advancing contact angles (theta) range from 7 degrees for PAH/PAA films through to 53 degrees for PAH/PSS films. X-ray photoelectron spectroscopy measurements indicate that the increase in film hydrophobicity is due to an increase in PSS concentration at the film surface. In addition, the influence of added electrolyte in the PE solutions was investigated. Adsorption from PE solutions containing added salt favors PSS adsorption and results in more hydrophobic films. The amount of IgG adsorbed on the multilayer films systematically increased on films assembled from blends with increasing PSS content, suggesting strong interactions between PSS in the multilayer films and IgG. Hence, multilayer films prepared from blended PE solutions can be used to tune film thickness and composition, as well as wetting and protein adsorption characteristics.     

Colloid surface engineering via deposition of multilayered thin films from polyelectrolyte blend solutions

Multilayer thin films were constructed on polystyrene colloidal particles by depositing alternating layers of poly(allylamine hydrochloride) (PAH) at pH 7.5 and varying composition blends of poly(acrylic acid) (PAA) and poly(styrenesulfonate) (PSS) at pH 3.5. Following the deposition of each layer, microelectrophoresis experiments showed alternating zeta-potentials, suggesting the formation of multilayered films on the particles. Scanning and transmission electron microscopy were used to examine the surface morphology of the colloidal particles, with homogeneous surface coatings apparent for films deposited from PAA/PSS blend solutions containing up to 90 wt % PAA. The colloidal stability of these particles is greater than those coated with individual PAH and PAA layers. In the case of the blend PAA/PSS = 25:75 wt %, up to 20 layers were assembled without compromising the colloidal stability of the dispersion. The results demonstrate that the deposition of layers from PE blend solutions containing a strong and weak PE can be used as a facile method for controlling the surface properties and hence the colloidal stability of core-shell particles, as well as the thickness and morphology of the coatings. Control of these parameters is important for subsequent processing and application of these particles in controlled delivery, photonics, catalytic, and separation applications.     

枝状文石型碳酸钙的仿生合成及在PVC中的应用

利用生物矿化原理,以聚丙烯酸(PAA)为有机基质,采用碳化法合成了具有枝状形貌的文石型碳酸钙粒子.通过场发射扫描电镜(FESEM)、X射线衍射仪(XRD)和傅里叶变换红外光谱仪(FTIR)等检测手段研究了产物的结构和形貌,并初步探讨了粒子的生长机理.结果表明,在文石型碳酸钙粒子的合成中,有机基质和反应温度是非常重要的参数.同时将该产品填充于聚氯乙烯(PVC)中,测定了PVC塑料的力学性能和加工性能.     

Characterization of the growth of polyelectrolyte multilayers formed at interfaces between aqueous phases and thermotropic liquid crystals

Polyelectrolyte multilayers (PEMs) formed at interfaces between aqueous solutions and thermotropic (water-immiscible) liquid crystals (LCs) offer the basis of a new method to tailor the nanometer-scale structure and chemical functionality of these interfaces. Toward this end, we report a study that compares the growth of PEMs formed at mobile and deformable interfaces defined by LCs relative to growth observed at model (rigid) solid surfaces. Experiments aimed at determining if polyelectrolytes such as poly(sodium-4-styrenesulfonate) (PSS) can partition from the aqueous phase into the bulk of the LC yielded no evidence of such partitioning. Whereas measurements of the growth of PEMs formed from poly(allylamine hydrochloride) (PAH) and PSS at the aqueous-LC interface revealed growth characteristics similar to those measured at both hydrophobic and hydrophilic interfaces of solids, the growth of PEMs from PAH and poly(acrylic acid) (PAA) at the aqueous-LC interface was found to differ substantially from the solids investigated: (i) the linear growth of PEMs of PAH/PAA that was measured at the aqueous-LC interface under conditions that did not lead to the growth of PEMs at the interface of octadecyltrichlorosilane (OTS)-treated glass (a hydrophobic solid surface), and (ii) in comparison to the growth of PEMs of PAH/PAA at the surface of glass (a hydrophilic charged surface), a higher rate of growth was observed at the aqueous-LC interface. The finding that the growth rate of PEMs of PAH/PAA at aqueous-LC interfaces is greater than on solid surfaces is supported by additional measurements of growth as a function of pH. Finally, the pH-triggered reorganization of PAH/PAA PEMs supported at the aqueous-LC interface led to changes in the order and optical properties of the LC. These data are discussed in light of the nature of aqueous-LC interfaces, including the mobility and deformability of the interface and recent measurements of the zeta-potentials of aqueous-LC interfaces.     

NUCLEATION MECHANISM OF PEO BLOCK IN DOUBLE-CRYSTALLINE POLY（ETHYLENE-co-BUTENE）-b-POLY（ETHYLENE OXIDE） BLOCK COPOLYMERS

In this paper, we proposed a method to determine the nucleation effect of pre-existing crystals on crystallization of the second block in double crystalline block copolymers, which is usually covered by the suppression effect. The nucleation mechanism of poly（ethylene oxide） （PEO） block from the pre-crystallized polyethylene （PE） block in poly（ethylene-cobutene）-b-poly（ethylene glycol） （EmEOn） diblock copolymers was investigated under variable crystallization environments. The crystallization environment for the PEO block was altered by cooling at different cooling rates or successive selfnucleation （SSN） to the PE block. It was found that the presence of nucleation effect is strongly dependent on composition of the block copolymers. The crystallization temperature （Tc） of PEO block in E174EO90 increases as cooling rate applied to the PE block decreases, indicating that PE block can nucleate the crystallization of PEO block and more perfect PE crystals have stronger nucleation effect. In E182EO41 crystallization of the PEO block is confined, shown by the disappearance of selfnucleation domain, and the PE block has no nucleation effect on the crystallization of PEO block. Double crystallization peaks are observed for the PEO block in E182EO41 and the intensity of the crystallization peak at higher temperature increases as the PE crystals become more perfect. After exclusion of homogeneous nucleation mechanism, the higher temperature crystallization peak of the PEO block in E182EO41 is tentatively ascribed to surface nucleation.     

Polyelectrolyte Multilayer Films Containing Ferrocene: Effects of Polyelectrolyte Type and Ferrocene Contents in the Film on the Redox Properties

Electrochemical properties of Fc‐PEM films have been studied by changing the chemical structure of the polymer chains and the content of Fc moiety in the film systematically. We have prepared a series of PEM films by a layer‐by‐layer deposition of polycations, Fc‐modified poly(allylamine) (Fc‐PAA) and poly(ethyleneimine) (Fc‐PEI), and polyanionic poly(vinyl sulfate) (PVS) on the surface of a gold electrode. The redox properties of the Fc‐PAA/PVS and Fc‐PEI/PVS films depended significantly on the content of Fc moiety in the polymer chains and on the polymer type. Fc‐ PAA and Fc‐PEI polymer chains can penetrate 3 or 4 PAA/PVS bilayers inserted between the redox polymers and electrode. The Fc‐PAA film‐modified electrode can be used for electrocatalytic oxidation of ascorbic acid.     

A rod-linker-contained R-phycoerythrin complex from the intact phycobilisome of the marine red alga Polysiphonia urceolata

A linker-contained R-phycoerythrin (R-PE) complex was obtained by the Sephadex G-150 column chromatography from the Polysiphonia urceolata phycobilisome (PBS) that was dis-associated at 37 degrees C for 6 h in the dilute phosphate buffer (pH 7.0) with 5% (m/v) sodium dodecyl sulfate (SDS). The R-PE complex showed three absorption peaks at 498, 538 and 567 nm, and a fluorescence emission maximum at 578 nm. Polypeptide analysis of the complex by the 8-25% (m/v) gradient SDS-polyacrylamide gel electrophoresis demonstrated that it contained three red subunits, alpha(PE)(17.6),beta(PE)(19.2) and gamma(PE)(31.0), and a colorless 35.3 kDa rod-linker L(R)(35.3). Polypeptide proportion of the complex demonstrated that it was a hexamer in aggregate form gamma(PE)(31.6), (alpha(PE)(17.6),beta(PE)(19.2))(3)L(R)(35.3)(alpha(PE)(17.6),beta(PE)(19.2)(3)gamma(PE)(31.6) which is proposed to originate from a rod assembly of hexamer-linker-hexamer the substructure alpha(PE)(17.6),beta(PE)(19.2)(3) of which was decomposed off from the ends of the assembly during the PBS dissociation. The distinctive stability of the prepared hexamer is attributed to a large extent to the electrostatic interaction among its polypeptides, but not to the hydrophobic interaction.     

Polyelectrolyte layer-by-layer self-assembly enhanced by electric field and their multilayer membranes for separating isopropanol–water mixtures

An electric field enhanced method is developed for fabricating layer-by-layer (LbL) self-assembly polyelectrolyte multilayer membranes. Three kinds of electric field enhanced polyelectrolyte multilayer membranes (EPEMs), poly(diallyl dimethylammonium chloride)/poly(styrenesulfonate sodium salt) (PDDA/PSS), poly(diallyldimethylammonium chloride)/poly(acrylic acid sodium salt) (PDDA/PAA) and polyethylenimine/poly(acrylic acid sodium salt) (PEI/PAA), were self-assembled on a reverse osmosis membrane (ROM). The pervaporation performances of EPEMs for separating isopropanol–water mixtures (90/10, w/w) are all superior to those of corresponding normal self-assembled polyelectrolytes membranes (PEMs), and the selectivity increases with PDDA/PSS, PDDA/PAA and PEI/PAA in order. For (PEI/PAA)₄PEI EPEM, the separation factor is 1075 and permeation flux is 4.05 kg m⁻² h⁻¹ at 70 °C. This novel method speeds up the LbL process, which makes it promising for the practical application of the LbL multilayer membrane.     

PEI/PAA/APP三组分膨胀组装涂层阻燃改性苎麻织物

利用聚乙烯亚胺(PEI)的正电荷性及聚磷酸铵(APP)和聚丙烯酸(PAA)的负电荷性,通过层层组装技术在柔顺多孔的苎麻织物表面交替构筑了(PEI/PAA/PEI/APP)n膨胀型阻燃涂层,并对处理前后的苎麻织物的热稳定性和阻燃性等性质进行了表征.热失重分析(TGA)、微型量热仪(MCC)以及垂直燃烧测试(VFT)结果表明,阻燃处理后织物的热稳定性和阻燃性显著提高.同时与(PEI/APP)n试样相比,引入不同浓度的第3组分PAA在组装层数较少时通过增加PEI的电荷密度等作用可有效增加吸附量从而使上述性能有所提高,层数较高时由于APP和PAA的同性电荷紊乱,阻燃性的提升受到限制.     

Activity and lifetime of urease immobilized using layer-by-layer nano self-assembly on silicon microchannels

Urease has been immobilized and layered onto the walls of manufactured silicon microchannels. Enzyme immobilization was performed using layer-by-layer nano self-assembly. Alternating layers of oppositely charged polyelectrolytes, with enzyme layers “encased” between them, were deposited onto the walls of the silicon microchannels. The polycations used were polyethylenimine (PEI), polydiallyldimethylammonium (PDDA), and polyallylamine (PAH). The polyanions used were polystyrenesulfonate (PSS) and polyvinylsulfate (PVS). The activity of the immobilized enzyme was tested by pumping a 1 g/L urea solution through the microchannels at various flow rates. Effluent concentration was measured using an ultraviolet/visible spectrometer by monitoring the absorbance of a pH sensitive dye. The architecture of PEI/PSS/PEI/urease/PEI with single and multiple layers of enzyme demonstrated superior performance over the PDDA and PAH architectures. The precursor layer of PEI/PSS demonstrably improved the performance of the reactor. Conversion rates of 70% were achieved at a residence time of 26 s, on d 1 of operation, and >50% at 51 s, on d 15 with a six-layer PEI/urease architecture.     

The effect of support material and conditioning on wettability of PAH/PSS multilayer films

An efficient method for characterizing wetting properties of heterogeneous surfaces produced by sequential adsorption of polyelectrolytes was developed. Three types of polyelectrolytes were used: polyallylamine hydrochloride (PAH), polyethyleneimine (PEI), both of a cationic type, and polysodium 4-styrenesulfonate (PSS), of an anionic type. Multilayer films were prepared by 'layer-by-layer' (LbL) deposition technique. Natural ruby mica, glass, titanium foil and silicon wafers were used as the support material for PE films. Wetting of polyelectrolyte films was determined experimentally by contact angle measurements, using technique of direct image analysis of shape of sessile drops. Periodic oscillations in contact angle values were observed for multilayers terminated by polycation and polyanion, respectively, and the variations in contact angle values strongly depended on the conditions of adsorption and multilayer treatment after deposition. Therefore, the influence of ionic strength of polyelectrolyte solution used for deposition on wetting of multilayer films was considered and also the effect of conditioning in different environments was investigated. It is usually assumed that film properties and stability strongly depend on the first layer which is used to anchor a multilayer at the surface of support material. To investigate influence of the first layer, PAH/PSS films were compared with more complex ones having PEI as the first layer with a sequence of PSS/PAH deposited on top of it.     

High-resolution analysis of the influence of reactant concentration on nucleation time and growth of polyethyleneimine-trimethoxymethylsilane particles

High-resolution dynamic light scattering (DLS), scanning electron microscopy (SEM), time-lapse photography, and attenuated total reflectance Fourier transform infrared spectroscopy were used to analyze the growth kinetics of polyethyleneimine (PEI)-silica particles fabricated from the condensation of hydrolyzed trimethoxymethylsilane (TMOMS) and PEI/phosphate buffer (PEI/PB). Depending on the concentration of hydrolyzed TMOMS and PEI/PB, three stages were identified. We observed the existence of a nucleation time that has never been reported in the literature when TMOMS has been used. During this nucleation time, particles of less than 25 nm were detected using in situ DLS measurements taken every 15 s (high resolution), a DLS time-scale resolution not previously reported. In addition, the length of the nucleation time depended mainly on the PEI/PB concentration, but also TMOMS concentration. The growth stage was evident from the rapid increase of particle size with time. Due to the high resolution of the DLS measurements, a peak could be observed in the particle diameter during particle growth, which corresponds to a secondary population of particles required for the larger particles to further increase in size. Finally, during the equilibrium region, particles reached their maximum diameter that was independent of the concentration of PEI/PB and only changed with concentration of hydrolyzed TMOMS.     

Poly(acrylic acid)-poly(ethylene glycol) layers on positively charged surface coatings: molecular structure, protein resistance, and application to single protein deposition

A new copolymer (PAA-PEG2000) has been designed, consisting of a negatively charged poly(acrylic acid) (PAA) backbone to which poly(ethylene glycol) (PEG) side chains with a molecular weight of about 2 kDa were grafted in a molecular ratio of 3:10. It readily adsorbs to positively charged surfaces and may be considered to be the anionic counterpart of PEG-grafted poly(l-lysine) (PLL-PEG), which was first described by Kenausis et al. and is widely used to render negatively charged surfaces protein-resistant. The synthesis of PAA-PEG2000 can be carried out in aqueous solution at room temperature and does not require any sophisticated techniques such as handling in an inert gas atmosphere. Using ellipsometry and infrared reflection absorption spectroscopy (IRRAS), the film structure has been carefully analyzed for copolymer adsorption onto three different positively charged surfaces, namely, thin layers of poly(allylamine) (PAH), poly(ethyleneimine) (PEI) and (3-aminopropyl)triethoxysilane (APTES). Besides the film thickness, the conformation of the PEG chains and their orientation with respect to the surface normal appear to be important parameters for the protein resistance of the films. Although PAA-PEG2000 adsorbed to PAH and PEI renders the surfaces inert, only partial protein resistance has been observed if the copolymer is deposited on APTES. In a model application, we have generated heterogeneous surfaces composed of isolated small Au nanoparticles (AuNP's) embedded in a protein-resistant layer of PAA-PEG2000 and demonstrated that the AuNP's can serve as adsorption sites for single protein species. In the future, these nanopatterned surfaces may be used for the investigation of isolated proteins.     

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.