Proton diffusion in the superprotonic phase of [(NH4)1 − xRbx]3H(SO4)2 as studied by 1H spin-lattice relaxation

Proton diffusion in [(NH₄)_1 ? xRb_x]₃H(SO₄)₂ (0 < x < 1) has been studied by means of ¹H spin-lattice relaxation times, T₁. The relaxation times were measured at 200.13 MHz in the range of 296–490 K and at 19.65 MHz in the range of 300–470 K. In the high-temperature phase (phase I), translational diffusion of the acidic protons relaxes both the acidic protons and the ammonium protons. Spin diffusion averages the relaxation rate of the two kinds of protons, whereas proton exchange between them are slow. The spin-lattice relaxation times in phase I were analyzed theoretically, and parameters of proton diffusion were obtained. The mean residence time of the acidic protons increases with increase in x for [(NH₄)_1 ? xRb_x]₃H(SO₄)₂ (0 ≤ x ≤ 0.54). Rb₃H(SO₄)₂ does not obey this trend. The results of NMR well explain the macroscopic proton conductivity.     

Proton diffusion in the room-temperature phase of [(NH4)1−xRbx]3H(SO4)2 as studied by 1H spin-lattice relaxation in the rotating frame

Proton diffusion in the room-temperature phase (phase II) of [(NH₄)_1?xRb_x]₃H(SO₄)₂ (0≤x≤1) has been studied by means of ¹H spin-lattice relaxation times in the rotating frame, T_1ρ. The ¹H T_1ρ values were measured at 200.13 MHz in the range of 380–490 K. The ammonium protons and the acidic protons have independent T_1ρ values in the higher temperature range of phase II, suggesting that the spin diffusion between the two species is ineffective. The translational diffusion of the acidic protons is the most dominant mechanism to relax both the ammonium protons and the acidic protons in phase II. The ¹H T_1ρ values in phase II are analyzed theoretically and the motional parameters are obtained. The results of NMR well explain the macroscopic proton conductivity.     

Proton dynamics in Cs3(HSO4)2(HPO4) studied by 1H NMR

Proton dynamics in Cs₃(HSO₄)₂(H₂PO₄) has been studied by means of ¹H solid-state NMR as well as thermal analyses. The thermal analysis shows an endothermic peak at 408 K, which corresponds to a superprotonic transition. Above the transition temperature a mass loss is observed in a dry atmosphere, which is easily recovered in a conventional dry atmosphere below the transition temperature. The ¹H magic-angle-spinning NMR spectra at room temperature show two peaks at 13.5 and 15.8 ppm, and a shoulder at 11.3 ppm from tetramethylsilane, demonstrating a presence of several inequivalent proton sites. Translational diffusion of protons takes place in both a room-temperature phase (RT) and a high-temperature phase (HT). In both phases reorientation of the SO₄/PO₄ tetrahedron limits the rate of the proton transport. The ¹H mean residence times are estimated as E_a = 33 kJ mol^− 1 and τ₀ = 0.97 × 10^− 9 s for phase RT from the second moment analysis and as E_a = 20 kJ mol^− 1 and τ₀ = 5.0 × 10^− 12 s for phase HT from the analysis of the ¹H T₁ results.     

Structural,vibrational study and superprotonic behavior of a new mixed dipotassium hydrogenselenate dihydrogenphosphate K2(HSeO4)1.5(H2PO4)0.5

Ongoing studies of the KHSeO₄–KH₂PO₄ system aiming at developing novel proton conducting solids resulted in the new compound K₂(HSeO₄)_1.5(H₂PO₄)_0.5 (dipotassium hydrogenselenate dihydrogenphosphate). The crystals were prepared by a slow evaporation of an aqueous solution at room temperature. The structural properties of the crystals were characterized by single-crystal X-ray analysis: K₂(HSeO₄)_1.5(H₂PO₄)_0.5 (denoted KHSeP) crystallizes in the space group P 1¯ with the lattice parameters: a = 7.417(3) Å, b = 7.668(2) Å, c = 7.744(5) Å, α = 71.59(3)°, β = 87.71(4)° and γ = 86.04(6)°. This structure is characterized by HSeO₄⁻ and disordered (H_xSe/P)O₄⁻ tetrahedra connected to dimers via hydrogen bridges. These dimers are linked and stabilized by additional hydrogen bonds (O–H–O) and hydrogen bridges (O–H…O) to build chains of dimers which are parallel to the [0, 1, 0] direction at the position x = 0.5.The differential scanning calorimetry diagram showed two anomalies at 493 and 563 K. These transitions were also characterized by optical birefringence, impedance and modulus spectroscopy techniques. The conductivity relaxation parameters of the proton conductors in this compound were determined in a wide temperature range. The transport properties in this material are assumed to be due to H⁺ protons hopping mechanism.     

Super-protonic phase transition and fast ionic conductivity of Li+ in [Li0.2(NH4)0.8]2TeCl6

The differential scanning calorimetry diagram of [Li_0.2(NH₄)_0.8]₂TeCl₆ showed one anomaly at 526 K accompanied with a shoulder at 505 K.The conductivity plot exhibits two anomalies at 496 and 526 K, which characterize the beginning and the end of the crossing to superionic conductor state. The low temperature conduction is ensured essentially by Li⁺. A sudden jump confirms the presence of a superionic protonic transition related to the fast motion of Li⁺ and H⁺ ions. Above 526 K, the high temperature phase is characterized by high electrical conductivity (10^− 3 Ω^− 1 m^− 1) and low activation energy (E_a < 0.3 eV).The dielectric constant evolution as a function of frequency and temperature revealed the same anomaly.Transport properties in this material appear to be due to Li⁺ and H⁺ ions' hopping mechanism.     

Bulk and surface properties of ionic salt CsH5(PO4)2

We report a comparative study of transport and thermodynamic properties of single-crystal and polycrystalline samples of the ionic salt CsH₅(PO₄)₂ possessing a peculiar three-dimensional hydrogen-bond network. The observed potential of electrolyte decomposition ≈ 1.3 V indicates that the main charge carriers in this salt are protons. However, in spite of the high proton concentration, the conductivity appears to be rather low with a high apparent activation energy E_a ≈ 2 eV, implying that protons are strongly bound. The transport anisotropy though is not large, correlates with the crystal structure: the highest conductivity is found in the [001] direction (σ_130 °C ∼ 5.6 × 10^− 6 S cm^− 1) while the minimal conductivity is in the [100] direction (σ_130 °C ∼ 10 ⁻⁶ S cm^− 1). The conductivity of polycrystalline samples appears to exceed the bulk one by 1–3 orders of magnitude with a concomitant decrease of the activation energy (E_a ≈ 1.05 eV), which indicates that a pseudo-liquid layer with a high proton mobility is formed at the surface of grains. Infrared and Raman spectroscopy used to study the dynamics of the hydrogen-bond system in single-crystal and polycrystalline samples have confirmed the formation of such a modified surface layer in the latter. However, no bulk phase transition into the superionic disordered phase is observed in CsH₅(PO₄)₂ up to the melting point T_melt ∼ 151.6 °C, in contrast to its closest relative compound CsH₂PO₄.     

Conductivity and dielectric relaxation phenomena in (NH4)2SO4 single crystal

AC impedance measurements have been carried out on (NH₄)₂SO₄ single crystals for the temperatures from 300 to 473 K and frequency range between 100 Hz and 4 MHz. The results reveal two distinct relaxation processes in the sample crystal. One is the dipolar relaxation with a peak at frequency slightly higher than 4 × 10⁶ Hz. The other is the charge carrier relaxation at lower frequencies. The frequency dependence of conductivity is described by the relation σ(ω) = Bωⁿ, and n = 1.32 is obtained at temperatures below 413 K. This value drops to 0.2 and then decreases slightly with increasing temperature. The dipolar response of the (NH₄)₂SO₄ single crystal under an ac field is attributed to the reorientation of dipoles. The contribution of charge carriers is increasing substantially with increasing temperature at temperatures above 413 K. The temperature variation of conductivity relaxation peaks follows the Arrhenius relation. The obtained activation energy for migration of the mobile ions for (NH₄)₂SO₄ single crystal was 1.24 eV in the temperature range between 433 and 468 K in this intrinsic region. It is proposed that the NH₄⁺ in the sample crystal has the contribution to the electrical conduction.     

Structural,XPS and impedance analysis of LixCoVO4 (x = 0.8, 1.0, 1.2)

Lithium cobalt vanadate Li_xCoVO₄ (x = 0.8; 1.0; 1.2) has been prepared by a solid state reaction method. The XRD analysis confirms the formation of the sample. A new peak has been observed for Li_1.0CoVO₄ and for Li_1.2CoVO₄ indicating the formation of a new phase. The XPS analysis indicates the reduction in the oxidation of vanadium and oxygen with the addition of Li in Li_xCoVO₄ (x = 0.8, 1.0, 1.2). The impedance analysis gives the conductivity value as 2.46 × 10^− 5, 6.16 × 10^− 5, 9 × 10^− 5 Ω^− 1 cm^− 1 for Li_xCoVO₄ (x = 0.8; 1.0; 1.2), all at 623 K. The similarity in the bulk activation energy (E_a) and the activation enthalpy for migration of ions (E_ω) indicate that the conduction in Li_1.2CoVO₄ has been due to hopping mechanism.     

Synthesis,crystal structure,spectroscopic characterization and optical properties of bis(4-acetylanilinium) tetrachlorocobalt (II)

The chemical preparation, crystal structure, spectroscopic investigations and optical features are given for a novel organic–inorganic hybrid material [C₈H₁₀NO]₂CoCl₄.The compound is crystallized in the orthorhombic space group Cmca, with the following unit cell parameters: a=19.461(2) Å, b=15.523(2) Å, c=13.7436(15) Å, and Z=8. The atomic arrangement shows an alternation of organic and inorganic layers along the b-axis. The cohesion between these entities is performed by N–H…Cl and N–H…O hydrogen bonds and π–π stacking interactions.Infrared and Raman spectra at room temperature are recorded in the 4000−400 and 4000−0 cm⁻¹ frequency regions, respectively and analyzed on the basis of literature data. This study confirms the presence of the organic cation [C₈H₁₀NO]⁺ and of the [CoCl₄]²⁻ anion. UV–vis spectroscopy results showed the indirect transition with band gap energy 2.98 eV.     

Vibrational study,phase transitions and electrical properties of 4-benzylpyridinium monohydrogenselenate

The title compound C₆H₅CH₂C₅H₄NH⁺·HSeO₄⁻ crystallizes in the orthorhombic system with the space group Pbca and the following unit cell dimensions: a=27.449(5) Å; b=10.821(6) Å and c=8.830(1) Å.The structure consists of infinite parallel two-dimensional planes built of HSeO₄⁻ anions and C₆H₅CH₂C₅H₄NH⁺ cations mutually.Differential scanning calorimetry study on 4-benzylpyridinium monohydrogen-selenate was carried out. A high temperature second order phase transition at 363 K was found and characterized by electric measurements. The Raman of polycrystalline sample has been recorded at different temperature between 297 and 373 K.The conductivity relaxation parameters associated with some H⁺ conduction have been determined from an analysis of the M′′/M′′_max spectrum measured in a wide temperature range. An appearance of the superionic phase transition in 4-BSe is closely related to a liberation or even a rotation increase of HSeO₄⁻ groups with heating.     

Chalcogen based treatment of InAs with [(NH4)2S/(NH4)2SO4]

A sulphur based chemical, ([(NH₄)₂S/(NH₄)₂SO₄]) to which S has been added not previously reported for the treatment of (111)A InAs surfaces is introduced and benchmarked against the commonly used passivants Na₂S·9H₂O and ((NH₄)₂S + S), using Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). It has been found that the native oxide layer present on the InAs surface is more effectively removed when treated with ([(NH₄)₂S/(NH₄)₂SO₄] + S) than with ((NH₄)₂S + S) or Na₂S·9H₂O. AES depth profiles of the sulphurized layers revealed the formation of a thin (less than 8.5 nm) In–S surface layer for both ((NH₄)₂SO₄ + S) and ([(NH₄)₂S/(NH₄)₂SO₄] + S) treatments. No evidence for the formation of As―S bonds was found. Treatment with ([(NH₄)₂S/(NH₄)₂SO₄] + S) also affected a significant improvement compared to the more established sulphur treatments in the surface morphology of the otherwise poor as-received n-InAs (111)A surface.     

High-pressure dielectric studies of a novel hydrogen-bonded ferroelectric (NH4)2H2P2O6

The hydrostatic pressure effect on the dielectric properties of (NH₄)₂H₂P₂O₆ ferroelectric crystal was studied for pressures from 0.1 MPa to 360 MPa and for temperatures from 100 to 190 K. The pressure–temperature phase diagram obtained is linear with increasing pressure. The paraelectric–ferroelectric phase transition temperature decreases with increasing pressure with the pressure coefficient dT_c/dp=?5.16×10^?2 K MPa^?1. Additionally, the pressure dependences of Curie–Weiss constants for the crystal in paraelectric (C₊) and ferroelectric (C_?) phases are evaluated and discussed. The possible mechanism of paraelectric–ferroelectric phase transition is also discussed.     

Polymorphic phase transition and thermal stability in squaric acid (H2C4O4)

Phase transformations in squaric acid (H₂C₄O₄) have been investigated by thermogravimetry and differential scanning calorimetry with different heating rates β. The mass loss in TG apparently begins at onset temperatures T_di=245±5 °C (β=5 °C min^?1), 262±5 °C (β=10 °C min^?1), and 275±5 °C (β=20 °C min^?1). A polymorphic phase transition was recognized as a weak endothermic peak in DSC around 101 °C (T_c⁺). Further heating with β=10 °C min^?1 in DSC revealed deviation of the baseline around 310 °C (T_i), and a large unusual exothermic peak around 355 °C (T_p), which are interpreted as an onset and a peak temperature of thermal decomposition, respectively. The activation energy of the thermal decomposition was obtained by employing relevant models. Thermal decomposition was recognized as a carbonization process, resulting in amorphous carbon.     

Dielectric relaxation in NH4HSO4 above room temperature

The dispersion curves of the dielectric response of NH₄HSO₄ show that the corrected imaginary part of permittivity, εʺ, and its real part ε′ versus frequency reveal a dielectric relaxation around 9.1 × 10⁵ Hz at 31 °C, which shifts to higher frequencies (∼ 10⁶ Hz) as the temperatures increases. The relaxation frequency shows an activated relaxation process over the temperature range 31–83 °C with activation energy E_a = 0.14 eV, which is close to that derived from the dc conductivity. We suggest that the observed dielectric relaxation could be produced by the H⁺ jump and SO₄⁻ reorientation that cause distortion and change the local lattice polarizability inducing dipoles like HSO₄⁻.     

Transport and phase dynamics of poly(vinyl pyrrolidone) doped plastically crystalline N-methyl-N-propylpyrrolidinium tetrafluoroborate

The plastic crystal phase forming N-methyl-N-propylpyrrolidinium tetrafluoroborate organic salt (P₁₃BF₄) was combined with 2, 5 and 10 wt.% poly(vinyl pyrrolidone) (PVP). The ternary 2 wt.% PVP/2 wt.% LiBF₄/P₁₃BF₄ was also investigated. Thermal analysis, conductivity, optical thermomicroscopy, and Nuclear Magnetic Resonance (¹¹B, ¹⁹F, ¹H, ⁷Li) were used to probe the fundamental transport processes. Both the onset of phase I and the final melting temperature were reduced with increasing additions of PVP. Conductivity in phase I was 2.6 × 10^− 4 S cm^− 1 5.2 × 10^− 4 S cm^− 1 1.1 × 10^− 4 S cm^− 1 and 3.9 × 10^− 5 S cm^− 1 for 0, 2, 5 and 10 wt.%PVP/P₁₃BF₄, respectively. Doping with 2 wt.% LiBF₄ increased the conductivity by up to an order of magnitude in phase II. Further additions of 2 wt.% PVP slightly reduced the conductivity, although it remained higher than for pure P₁₃BF₄.     

Synthesis and characterization of Ge and Sn(II) iodide-doped thioborate anhydrous proton conductors

Metal iodide-doped anhydrous proton conductors in the series xMI₂ + (1 − x)(HBS₂)₃, where M = Ge and Sn, have been prepared. These samples improve upon the anhydrous proton conductivity shown previously in the H₂S + B₂S₃ + GS_y series, where G = Si, Ge, and As, through a displacement reaction to incorporate HI into the materials. This is analogous to doping a silver halide salt into fast ion conducting chalcogenide glasses, such as AgI + Ag₂S + B₂S₃ + SiS₂, which results in a one to two orders of magnitude improvement in the ionic conductivity. The structural modification of the boroxol ring units in the thioboric acid is discussed based on the infrared and Raman spectroscopy. The DC conductivity, estimated from AC impedance spectra, of the metal iodide-doped (HBS₂)₃ samples is reported as a function of temperature and related back to the underlying structural chemistry of these materials. The static solid state proton NMR spectra were also used to identify the proton environment and proton dynamics. These materials represent an improvement upon previous anhydrous proton-conducting materials and represent an important step in finding intermediate temperature proton conductors.     

A Boubaker polynomials expansion scheme (BPES)-related protocol for measuring sprayed thin films thermal characteristics

Measurements of In₂S₃ and ZnIn₂S₄ sprayed thin films thermal characteristics have been carried out using the photodetection technique. The thermal conductivity k and diffusivity D were obtained using a new protocol based on photothermal signal parameters analysis. Measured values of k and D were respectively, (15.2 ± 0.85) W m⁻¹K⁻¹ and (69.8 ± 7.1) × 10⁻⁶ m²s⁻¹ for In₂S₃, (7.2 ± 0.7) W m⁻¹K⁻¹ and (32.7 ± 4.3) × 10⁻⁶ m²s⁻¹ for ZnIn₂S₄. These values are extremely important since similar compounds are more and more proposed as Cd-free alternative materials for solar cells buffer layers.     

Oxygen diffusion and surface exchange studies on (La0.75Sr0.25)0.95Cr0.5Mn0.5O3−δ

Oxygen tracer diffusion coefficient (D^⁎) and surface exchange coefficient (k^⁎) have been measured for (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3−δ using isotopic exchange and depth profiling by secondary ion mass spectrometry technique as a function of temperature (700–1000 °C) in dry oxygen and in a water vapour-forming gas mixture. The typical values of D^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 4 × 10^− 10 cm² s^− 1 and 3 × 10^− 8 cm² s^− 1 respectively, whereas the values of k^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 5 × 10^− 8 cm s^− 1 and 4 × 10^− 8 cm s^− 1 respectively. The apparent activation energies for D^⁎ in oxidising and reducing conditions are 0.8 eV and 1.9 eV respectively.     

Laser ablation time-of-flight mass spectrometry (LA-TOF-MS) of “nitrogen doped diamond-like carbon (DLN) nano-layers”

Nitrogen-doped diamond-like carbon (DLC) layers (a-C:H:N, N-DLC or DLN) were prepared by the plasma-enhanced chemical vapor deposition (PECVD) technique, using a RF capacitive discharge (13.56 MHz), at low pressures (20 Pa), produced from a mixture of methane, nitrogen and hexamethyldisiloxane (HMDSO), deposited on single-crystalline silicon wafers placed on steel samples. The films, of differing deposition times, were subjected to laser ablation time-of-flight (LA-TOF) mass spectrometric measurements, using different commercial instrumentation to characterize their structures. The analysis of mass spectra was made and the following positively singly charged species were detected and identified: C_n⁺ (n=4–30), Si_n⁺ (n=2, 3), Si_nH⁺ (n=2, 3), SiOK⁺, Si₃H₄⁺, Si₂N⁺, Si₂NH₂⁺, and Si₃C⁺. The later three species could reflect the presence of nitrogen–silica and carbon–silica chemical bonds in the structure of the DLN layer. The stoichiometry of all species was confirmed by isotopic pattern simulation. In the negative detection mode, the C_n⁻ (n=2–12) clusters were observed. The findings are discussed in the light of the current research concerning analysis of the DLN thin layers and it is concluded that namely Si₂N⁺, Si₂NH₂⁺ and Si₃C⁺ species are reflecting the chemical structure of the DLN layer. LA-TOF-MS was found useful supplementary method for the characterization of DLN nano-layers.     

Structure,stability and electrical properties of the La(2−x)SrxMnO4±δ solid solution series

Single phase materials of the La_(2−x)Sr_xMnO_4±δ (0.6 ≤ x ≤ 2.0) solid solution series were prepared via solid state reaction. The structure of each material was examined at room temperature and determined to be tetragonal for all phases examined. An expansion in lattice volume was observed on increasing lanthanum content. The stability and thermal expansion of each member of the solid solution series was determined via the use of in situ high temperature X-ray diffraction. It was found that all materials remained stable up to a temperature of 800 °C. Thermal expansion coefficients were found to be in the region of 15 × 10^− 6 K^− 1 for La_(2−x)Sr_xMnO_4±δ compounds where x > 1.4. The electrical conductivity of each phase was also determined over a similar temperature range with a maximum value of ∼6 Scm^− 1 at 900 °C for the x = 1.8 phase.