Synthesis and visible light photocatalysis water splitting property of chromium-doped Bi4Ti3O12

Photocatalysts Bi₄Ti_3 ? xCr_xO₁₂(x = 0.00, 0.06, 0.15, 0.30, 0.40, and 0.50) with perovskite structure were synthesized by sol–gel method and their electronic structures and photocatalytic activities were investigated. The Bi₄Ti_2.6Cr_0.4O₁₂ photocatalyst exhibited the highest performance of H₂ evolution in methanol aqueous solution (58.1 μmol h^? 1 g^? 1) under visible light irradiation (λ > 400 nm) without a co-catalyst, whereas no H₂ evolution is observed for Bi₄Ti₃O₁₂ under the same conditions. The UV–vis spectra indicated that the Bi₄Ti_2.6Cr_0.4O₁₂ had strong photoabsorption in the visible light region. The results of density functional theory (DFT) calculation illuminate that the conduction bands of Bi₄Ti₃O₁₂ are mainly attributable to the Ti 3d + Bi 6p orbitals, and the valence bands are composed of O 2p + Bi 6s hybrid orbitals, while the conduction bands of chromium-doped Bi₄Ti₃O₁₂ are mainly attributable to the Ti 3d + Bi 2p + Cr 3d orbitals, and the O 2p + Cr 3d hybrid obitals are the main contribution to the valence band.     

Detection of OH radical and O atom during triboluminescence of hydrated cerium/terbium sulfates

Triboluminescence of Се₂(SO₄)₃·8H₂O and Tb₂(SO₄)₃·8H₂O crystals has been studied. For the first time spectral evidence for a contribution of light-emitting products OH^? (283 and 290 nm maxima, 1–0 transition; 308.4 and 309.6 nm, 0–0 transition) and excited oxygen atom O^? (777 nm, 3P⁵P—3S⁵S) produced via mechano-chemical decomposition of H₂O and O₂ molecules in the destruction of crystal hydrates of the salts to the gas-phase component of triboluminescence has been obtained.     

Spectroscopic properties of Sm3+ ions in lead fluorophosphate glasses

The Sm³⁺-doped lead fluorophosphate glasses of composition 44P₂O₅–17K₂O–9Al₂O₃–(24?x)PbF₂–6Na₂O–xSm₂O₃, where x=0.01, 0.05, 0.1, 0.5, 1.0 and 2.0 mol%, have been prepared by conventional melt quenching technique and are characterized through differential thermal analysis, Raman, absorption and emission spectra and decay rate measurements. Free-ion Hamiltonian model for energy level analysis and Judd–Ofelt theory for spectral intensities have been used to analyze the spectroscopic properties of Sm³⁺ ions in lead fluorophosphate glasses. The decay rates for the ⁴G_5/2 level of Sm³⁺ ions have been measured and are found to be single exponential at lower concentration (≤0.1 mol% Sm₂O₃) and turn into non-exponential at higher concentrations (≥0.5 mol% Sm₂O₃) due to energy transfer through cross-relaxation. The experimental lifetimes for ⁴G_5/2 level of Sm³⁺ ions are found to decrease from 2.54 to 0.92 ms when the concentration increased from 0.01 to 2.0 mol% Sm₂O₃ due to energy transfer. In order to know the nature of the energy transfer mechanism, the non-exponential decay rates are well fitted to Inokuti–Hirayama model for S=6, which indicates that the energy transfer process is of dipole–dipole type.     

Crystal structure of Fe-doped lanthanum gallate for oxygen partial pressures studied by neutron powder diffraction

Neutron powder diffraction experiments were carried out to investigate a change in a crystal structure of La_0.8Sr_0.2Ga_0.65Fe_0.35O₃ for oxygen partial pressures, P_O2, at 800 °C. The crystal structure was refined on the basis of the R3?c symmetry for the P_O2 range from 10^? 1 to 10^? 20 atm, by the Rietveld analysis. It was found that lattice parameters, a and c, monotonically expand with decreasing P_O2, and then both expansions are rapidly suppressed below 10^? 4 atm. In the meantime, l_M–O and l_O–O(2) also discontinuously increased with decreasing P_O2, while l_O–O(1) did not change at all P_O2, where l_M–O, l_O–O(1) and l_O–O(2) are the bond lengths within a MO₆ octahedron (M = Ga_0.65Fe_0.35). This result indicates that the l_M–O and the l_O–O(2) are more important than the l_O–O(1) for such a complicated lattice expansion for P_O2.     

Structural,vibrational study and superprotonic behavior of a new mixed dipotassium hydrogenselenate dihydrogenphosphate K2(HSeO4)1.5(H2PO4)0.5

Ongoing studies of the KHSeO₄–KH₂PO₄ system aiming at developing novel proton conducting solids resulted in the new compound K₂(HSeO₄)_1.5(H₂PO₄)_0.5 (dipotassium hydrogenselenate dihydrogenphosphate). The crystals were prepared by a slow evaporation of an aqueous solution at room temperature. The structural properties of the crystals were characterized by single-crystal X-ray analysis: K₂(HSeO₄)_1.5(H₂PO₄)_0.5 (denoted KHSeP) crystallizes in the space group P 1¯ with the lattice parameters: a = 7.417(3) Å, b = 7.668(2) Å, c = 7.744(5) Å, α = 71.59(3)°, β = 87.71(4)° and γ = 86.04(6)°. This structure is characterized by HSeO₄⁻ and disordered (H_xSe/P)O₄⁻ tetrahedra connected to dimers via hydrogen bridges. These dimers are linked and stabilized by additional hydrogen bonds (O–H–O) and hydrogen bridges (O–H…O) to build chains of dimers which are parallel to the [0, 1, 0] direction at the position x = 0.5.The differential scanning calorimetry diagram showed two anomalies at 493 and 563 K. These transitions were also characterized by optical birefringence, impedance and modulus spectroscopy techniques. The conductivity relaxation parameters of the proton conductors in this compound were determined in a wide temperature range. The transport properties in this material are assumed to be due to H⁺ protons hopping mechanism.     

Oxygen diffusion studies on (Y2O3)2(Sc2O3)9(ZrO2)89

The oxygen tracer diffusion coefficient (D?) has been measured for 9 mol% scandia 2 mol% yttria co-doped zirconia solid solution, (Y₂O₃)₂(Sc₂O₃)₉(ZrO₂)₈₉, using isotopic exchange and line scanning by Secondary Ion Mass Spectrometry, as a function of temperature. The values of the tracer diffusion coefficient are in the range of 10^? 8–10^? 7 cm² s^? 1 and the Arrhenius activation energy was calculated to be 0.9 eV; both valid in the temperature range of 600–900 °C. Electrical conductivity measurements were carried out using 2-probe and 4-probe AC impedance spectroscopy, and a 4-point DC method at various temperatures. There is a good agreement between the measured tracer diffusion coefficients (D?, Ea = 0.9 eV) and the diffusion coefficients calculated from the DC total conductivity data (D_σ, Ea = 1.0 eV), the latter calculated using the Nernst–Einstein relationship.     

Mixed conductivity and electrocatalytic performance of SrFeO3-δ–SrAl2O4 composite membranes

Oxygen-ionic and electronic transport in dense (SrFe)_1−x(SrAl₂)_xO_z composites, consisting of strontium-deficient Sr(Fe,Al)O_3-δ and SrAl₂O₄ phases, is determined by the properties of perovskite-like solid solution. Increasing the content of SrAl₂O₄, with a total conductivity as low as 5 × 10^− 7 −  10^− 5 S × cm^− 1 at 973–1273 K in air, results in the gradual decrease of the partial conductivities, but also enables the suppression of thermal expansion. Compared to single-phase SrFe_1−xAl_xO_3-δ, (SrFe)_1−x(SrAl₂)_xO_z composites exhibit enhanced thermomechanical properties, while the oxygen permeability of these materials has similar values. The composite membranes exhibit stable performance under air/(H₂–H₂O–N₂) and air/(CH₄–He) gradients at 973–1173 K. The oxidation of dry methane by oxygen permeating through (SrFe)_0.7(SrAl₂)_0.3O_z results in dominant total oxidation, suggesting the necessity to incorporate a reforming catalyst into the ceramic reactors for natural gas conversion.     

Evaluation of Sr- and Mn-substituted LaAlO3 as potential SOFC anode materials

Lanthanum–aluminate-based oxides, (La_0.8Sr_0.2)_1−yAl_1−xMn_xO_3−δ (x = 0, 0.3, 0.5; y = 0 or 0.06) (LSAM), were synthesized and evaluated in detail as potential anode materials for solid oxide fuel cells (SOFCs). The electrical conductivity of LSAM (Mn ≥ 30 mol%) is dominated by p-type electronic conduction and can be treated as a diluted system of lanthanum manganites, (La,Sr)MnO₃. At 810 °C, the electrical conductivity of (La_0.8Sr_0.2)_0.94Al_0.5Mn_0.5O_3−δ (LSAM8255b) reaches 12 S/cm in air and 2.7 S/cm in humidified Ar/4% H₂ (p(O₂) ≈ 10^− 18 bar). The thermal expansion coefficients of LSAM8255a and LSAM8255b match YSZ very well and no chemical reaction was observed between these two perovskite materials and YSZ up to at least 1400 °C. Fairly good electrochemical performance was observed for an LSAM8255b–YSZ composite anode. At 850 °C, the polarization resistances are only 0.34 and 0.50 Ω cm² in wet (∼3% H₂O) Ar/20% H₂ and wet Ar/20% CH₄, respectively. In addition, an exposure to Ar/20% CH₄/3% H₂O for 35 h did not cause any apparent carbon deposition on the electrode. However, the chemical stability of LSAM8255a and LSAM8255b in a typical anode environment under open circuit conditions does not seem sufficient, leading to performance degradation with time in wet Ar/20% H₂ or wet Ar/20% CH₄. Furthermore, relatively large chemical expansion (0.3–0.5%) was observed when the atmosphere was switched from air to wet Ar/4% H₂, which might cause intolerable stress on the thin film electrolyte layer for a large-area anode-supported planar SOFC, but which might be tolerable for small geometries or electrolyte-supported SOFCs.     

Spectroscopic characterization of Tm3+:TeO2–K2O–Nb2O5 glasses for 2-μm lasing applications

We have performed detailed experiments to investigate the spectroscopic properties of a new type of tellurite based host doped with thulium: Tm₂O₃:(0.70)TeO₂–(0.15)K₂O–(0.15)Nb₂O₅ having Tm₂O₃ concentrations of 0.125, 0.25, 0.5, and 1.0 mol%. By performing a Judd–Ofelt analysis of the absorption bands, we obtained average radiative lifetimes of 2.57±0.20 and 0.35±0.01 ms for the ³H₄ and ³F₄ levels, respectively. Furthermore, we also observed that an increase in the Tm₂O₃ concentration from 0.125 to 1.0 mol% results in a decrease of the measured fluorescence lifetime from 814 to 439 μs and from 258 to 47 μs for the ³H₄ and ³F₄ levels, respectively, due to efficient non-radiative decay. The highest quantum efficiency of 32% was obtained for the sample doped with 0.125 mol% Tm₂O₃ for the ³H₄ level. Results show that cross relaxation becomes important as the ion concentration is increased, leading to the quenching of the 1460-nm band and enhancement of the 1860-nm emission. The highest emission cross section of 6.85×10^?21 cm² measured for the 1860-nm band reveals the potential of this host for the development of 2-μm lasers in bulk glass as well as fiber media.     

Mixed conductivity,stability and thermomechanical properties of Ni-doped La(Ga,Mg)O3−δ

Perovskite-type LaGa_0.65Mg_0.15Ni_0.20O_3−δ exhibiting oxygen transport comparable to that in K₂NiF₄-type nickelates was characterized as a model material for ceramic membrane reactors, employing mechanical tests, dilatometry, oxygen permeability and faradaic efficiency measurements, thermogravimetry (TG), and determination of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10^− 15 Pa to 40 kPa. Within the phase stability domain which is similar to La₂NiO_4+δ, the defect chemistry of LaGa_0.65Mg_0.15Ni_0.20O_3−δ can be adequately described by the ideal solution model with oxygen vacancies and electron holes to be the only mobile defects, assuming that Ni²⁺ may provide two energetically equivalent sites for hole location. This assumption is in agreement with the density of states, estimated from thermopower, and the coulometric titration and TG data suggesting Ni⁴⁺ formation in air at T < 1150 K. The hole conductivity prevailing under oxidizing conditions occurs via small-polaron mechanism as indicated by relatively low, temperature-activated mobility. The ionic transport increases with vacancy concentration on reducing p(O₂) and becomes dominant at oxygen pressures below 10^− 7–10^− 5 Pa. The average thermal expansion coefficients in air are 11.9 × 10^− 6 and 18.4 × 10^− 6 K^− 1 at 370–850 and 850–1270 K, respectively. The chemical strain of LaGa_0.65Mg_0.15Ni_0.20O_3−δ ceramics at 1073–1123 K, induced by the oxygen partial pressure variations, is substantially lower compared to perovskite ferrites. The flexural strength determined by 3-point and 4-point bending tests is 167–189 MPa at room temperature and 85–97 MPa at 773–1173 K. The mechanical properties are almost independent of temperature and oxygen pressure at p(O₂) = 1–2.1 × 10⁴ Pa and 773–1173 K.     

Anomalous conductivity and microstructure in gadolinium doped ceria prepared from nano-sized powder

The temperature and the oxygen partial pressure dependences of the electron and hole conductivities were measured by the dc polarization method using a Hebb–Wagner's ion blocking cell for Gd_0.2Ce_0.8O_1.9 polycrystalline bodies with grain size of 0.5 μm prepared by sintering of nano-sized powder. A significant enrichment of gadolinium was observed in the vicinity of the grain boundary by TEM/EDS analyses. The electron conductivity were comparable with those of conventional Gd_0.2Ce_0.8O_1.9 polycrystalline body with grain size of 2 μm, and it followed p(O₂)^− 1/4 dependence at temperatures T = 973–1273 K. However, the observed hole conductivity was higher than that of conventional Gd_0.2Ce_0.8O_1.9, and it did not follow p(O₂)^1/4 dependence. This anomalous p(O₂) dependence disappeared after the sample was treated at T = 1773 K for 38 h and grain size was enlarged to 2–10 μm.     

Crystal growth and refinement of K1.88Ga1.88Sn8.12O16 hollandite-type compound

We grew single crystals of K_1.88Ga_1.88Sn_6.12O₁₆ hollandite-type compound and precisely determined their crystal structure by X-ray diffraction. K_1.88Ga_1.88Sn_6.12O₁₆ fibrous crystals measuring an average of about 2 mm in length and 60 μm in diameter were obtained by slow-cooling (from 1623 K to 1273 K) of a flux melt consisting of a 40 mol% crystal composition of (K₂O)₁(Ga₂O₃)₁(SnO₂)₁ and a 60 mol% flux composition of (K₂O)₂(MoO₃)₁(B₂O₃). The unit cell of K_1.88Ga_1.88Sn_6.12O₁₆ (a = 1.0389(2) nm, c = 0.3132(2) nm, V =  0.3381(2) nm³) was larger than that of K_1.52Ga_1.52Ti_6.48O₁₆. The ionic size difference with the replacement of Ti by Sn, 10%, was relaxed by an anisotropic expansion of the octahedra by 2.6% in the (001) plane and 5.8% along the c-axis.     

Flux pinning and superconducting properties of melt-textured NEG-123 superconductor with TiO2 addition

We studied the effect of TiO₂ doping on flux pinning and superconducting properties of a melt-grown (Nd_0.33Eu_0.33Gd_0.33) Ba₂Cu₃O_y + 35 mol% Gd₂BaCuO₅ (70 nm in size) composite (NEG-123) processed in Ar–1% O₂ atmosphere. As indicated by similar, sharp superconducting transitions, the small quantities of TiO₂ used in our experiments did not deteriorate superconducting properties of the NEG material. Transmission electron microscopy (TEM) analysis found 20–50 nm Ti-based particles in the NEG-123 matrix. However, we have not observed the clouds of <10 nm sized particles in the NEG-123 matrix, as in the case of recently reported NEG-123 composites doped by Mo and Nb nanoparticles. Nevertheless, quite a good J_c–B performance in the 0.1 mol% Ti-doped sample, namely 550 kA/cm² at the self-field and at the secondary peak field (4.5 T) was achieved at 65 K, while 320 kA/cm² was obtained at zero-field at 77 K, and 50 kA/cm² at 90.2 K. The pinning effectiveness decreased with increasing Ti content above 0.2 mol%. The analysis of the pinning force showed that higher concentration of Ti (>0.2 mol%) increased the amount of normal pins (δl pinning), indicated by the Fp(h) peak shift from h = 0.42–0.36. The maximum pinning effect in a broad field range could be achieved by optimizing Ti content and adding sub-micron Gd-211 particles.     

Synthesis and electrical transport properties of Lu2+xTi2−xO7−x/2 oxide-ion conductors

The Lu_2+xTi_2−xO_7−x/2 (x = 0; 0.052; 0.096; 0.286; 0.44; 0.63; 33.3–49 mol% Lu₂O₃) nanoceramics with partly disordered pyrochlore-type structure are prepared by sintering freeze-dried powders obtained by a co-precipitation technique with 1600 °C annealing. Similar to pyrochlore-like compositions in the zirconate system, some of the new titanates are good oxide-ion conductors in air. The new solid-state electrolytes have oxide-ion conductivity in the interval of 1.0 × 10^− 3 – 2.5 × 10^− 3 S/cm at 740 °C in air. This value of conductivity is comparable with that of ZrO₂/Y₂O₃ ceramics. The conductivity of Lu_2+xTi_2−xO_7−x/2 depends on the chemical composition. The highest ionic conductivity is exhibited by nearly stoichiometric Lu_2+xTi_2−xO_7−x/2 (x = 0.096; 35.5 mol% Lu₂O₃) material containing ∼ 4.8 at.% Lu_Ti anti-site defects.     

Defect equilibria and partial molar properties of (La,Sr)(Co,Fe)O3−δ

The oxygen nonstoichiometry δ of La_1−xSr_xCo_1−yFe_yO_3−δ (x = 0.6 and y = 0.2, 0.4) was investigated by thermogravimetry in the range 703 ≤ T/°C ≤ 903 and 1E−5 < pO₂/atm < 1. The oxygen deficit increases with increasing T and decreasing pO₂. Electronic conductivities σ were measured as a function of pO₂ in the range 1E−5 < pO₂/atm < 1 at 700 ≤ T/°C ≤ 900. At constant T, a p-type pO₂-dependence of σ is observed. Oxygen nonstoichiometry data are analyzed with regard to the enthalpy and entropy of oxidation ΔH_ox^θ and ΔS_ox^θ, as well as to the partial molar enthalpy and entropy of oxygen with respect to the standard state of oxygen (pO₂^θ = 1 atm), (h_O − H_O^θ) and (s_O − S_O^θ), respectively. For 2.67 ≤ (3 − δ) ≤ 2.79, (h_O − H_O^θ) decreases with increasing δ, while (s_O − S_O^θ) is constant within the limits of error. Defect chemical modelling was performed by an ideal solution model under consideration of three different valence states for B-site ions (Co or Fe). The dependence of σ on δ is modelled, using calculated defect concentrations as functions of δ. Deviations from the ideal behaviour suggest an immobilization of n-type charge carriers by oxygen vacancies.     

Chemical diffusion of water in the double perovskites Ba4Ca2Nb2O11 and Sr6Ta2O11

The mechanism and kinetics of water incorporation in the double perovskites Ва₄Ca₂Nb₂O₁₁ and Sr₆Ta₂O₁₁ has been investigated (T = 300÷500 °C and aH₂O = 1 · 10^− 3÷2.2 · 10^− 2). The formation of hydration products Ba₄Ca₂Nb₂O₁₁·xH₂O and Sr₆Ta₂O₁₁·xH₂O (0.2 < x < 0.50) was limited by the diffusion of H₂O. It has been found that the concentration dependences of D˜_H2O are the same for both samples: small increasing of D˜_H2O with increasing x. The temperature dependences of the chemical diffusion coefficients of water for compositions of Ba₄Ca₂Nb₂O₁₁·0.35H₂O and Sr₆Ta₂O₁₁·0.35H₂O could be described with close activation energies of E_a = 0.38 ± 0.03 eV and E_a = 0.49 ± 0.03 eV, respectively. The chemical diffusion coefficients of water are nearly one order of magnitude smaller for tantalate Sr₆Ta₂O₁₁. This result correlates with lower oxygen and proton conductivities in Sr₆Ta₂O₁₁ as the consequence of lower mobilities.     

Effect of Li2O on the structure,electrical and dielectric properties of xLi2O·(20−x)CaO·30P2O5·30V2O5·20Fe2O3 glasses

Glasses of the general formula xLi₂O·(20?x)CaO·30P₂O₅·30V₂O₅·20Fe₂O₃ with x=0, 5, 10, 15 and 20 mol% were prepared; IR, density, electrical and dielectric properties have been investigated. Lithia-containing glasses revealed more (P₂O₇)^4?, FeO₆, V–O^? and PO^? groups and mostly have lower densities than those of lithia-free ones. The electrical properties showed random behavior by replacing Li₂O for CaO, which has been assigned to the change of the glass structure. The results of activation energy and frequency-dependent conductivity indicate that the conduction proceeds via electronic and ionic mechanisms, the former being dominant. The mechanism responsible for the electronic conduction is mostly thermally activated hopping of electrons from Fe(II) ions to neighboring Fe(III) sites and/or from V⁴⁺ to V⁵⁺. The dielectric constant (ε′) showed values that depend on the structure of glass according to its content of Li₂O. The (ε′) values are ranging between 3 and 41 at room temperature for 1 kHz, yet at high temperatures, glass with 20 mol Li₂O exhibits values of 110 and 3600 when measurement was carried out in the range 0.1–1 kHz, and at 5 MHz, respectively.     

Structural,ferroelectric, optical properties of A-site-modified Bi0.5(Na0.78K0.22)0.5Ti0.97Zr0.03O3 lead-free piezoceramics

We reported the role of A-site modification on the structural, ferroelectric, optical and electrical field-induced strain properties of Bi_0.5(Na_0.78K_0.22)_0.5Ti_0.97Zr_0.03O₃ lead-free piezoceramics. The Li⁺ ions with concentration from 0 to 5 mol% were used to substitute at A-site. There was no phase transition when Li⁺ ions was added up to 5 mol%. The electric field-induced strain (S_max/E_max) values increased from 600 to 643 pm/V for 2 mol% Li⁺-added which results from distortion both rhombohedral and tetragonal phase structures. The band gap reduced from 2.88 to 2.68 eV and the saturation polarization decreased from 46.2 to 26.1 μC/cm² when Li⁺ ions concentration increased from 0 to 5 mol% respectively. We expect that this work could be helpful for further understanding the role of A-site dopants in comparison with B-site modification in lead-free Bi_0.5(Na,K)_0.5TiO₃-based ceramics.     

Defect structure analysis of B-site doped perovskite-type proton conducting oxide BaCeO3 Part 1: The defect concentration of BaCe0.9M0.1O3−δ (M = Y and Yb)

By means of a high-temperature gravimetry, the defect chemical relationships between oxygen nonstoichiometry and water content in BaCe_0.9M_0.1O_3?δ (M = Y and Yb) were investigated as functions of partial pressure of oxygen, P(O₂), partial pressure of water vapor, P(H₂O), and temperature. Concentrations of protonic defect and that of oxygen vacancy strongly depend on P(H₂O) and temperature, while the dependences on P(O₂) were weak. The equilibrium constants of the water vapor incorporation reaction H₂O + V_O^??? + O_O^× = 2OH_O^? were determined. Concentrations of hole, [h^?], in the dry-atmospheres were determined by the weight gain by the incorporation of oxygen from the gas atmospheres. The [h^?] values increased with decreasing temperature. The [h^?] values were estimated to be about 2 to 3 orders of magnitude less than [OH_O^?] values measured in the wet-atmospheres.     

On the rate constants of OH + HO2 and HO2 + HO2: A comprehensive study of H2O2 thermal decomposition using multi-species laser absorption

Hydrogen peroxide (H₂O₂) and hydroperoxy (HO₂) reactions present in the H₂O₂ thermal decomposition system are important in combustion kinetics. H₂O₂ thermal decomposition has been studied behind reflected shock waves using H₂O and OH diagnostics in previous studies (Hong et al. (2009) [9] and Hong et al. (2010) [6,8]) to determine the rate constants of two major reactions: H₂O₂ + M → 2OH + M (k₁) and OH + H₂O₂ → H₂O + HO₂ (k₂). With the addition of a third diagnostic for HO₂ at 227 nm, the H₂O₂ thermal decomposition system can be comprehensively characterized for the first time. Specifically, the rate constants of two remaining major reactions in the system, OH + HO₂ → H₂O + O₂ (k₃) and HO₂ + HO₂ → H₂O₂ + O₂ (k₄) can be determined with high-fidelity.No strong temperature dependency was found between 1072 and 1283 K for the rate constant of OH + HO₂ → H₂O + O₂, which can be expressed by the combination of two Arrhenius forms: k₃ = 7.0 × 10¹² exp(550/T) + 4.5 × 10¹⁴ exp(?5500/T) [cm³ mol^?1 s^?1]. The rate constants of reaction HO₂ + HO₂ → H₂O₂ + O₂ determined agree very well with those reported by Kappel et al. (2002) [5]; the recommendation therefore remains unchanged: k₄ = 1.0 × 10¹⁴ exp(?5556/T) + 1.9 × 10¹¹⁺exp(709/T) [cm³ mol^?1 s^?1]. All the tests were performed near 1.7 atm.