Electrical conductivity of yttria-stabilized zirconia with cobalt addition

Yttria-stabilized zirconia is the most developed solid electrolyte for use in high-temperature solid oxide fuel cells. Commercial yttria-stabilized zirconia powders reach high densification at temperatures higher than that of the usual anode materials. Reduction of the sintering temperature of the solid electrolyte could allow for co-firing of both ceramic components, thereby reducing production costs. The main purpose of this work was to study the effect of small cobalt additions on densification and on electrical conductivity of 8 mol% yttria-stabilized zirconia. Linear shrinkage results show that the onset temperature for shrinkage decreases with increasing cobalt content. Impedance spectroscopy measurements reveal that the electrical conductivity depends on the sintering profile. For specimens sintered at 1400 °C for 0.1 h the electrical conductivity of grains and grain boundaries are almost unchanged with that of 8YSZ. In contrast, for specimens sintered at the same temperature but for 0.5 h of soaking time, the electrical conductivity is higher in 0.025 mol% samples and is lower for 1 mol% Co doped 8YSZ. Degradation of the microstructure by increased porosity was obtained for high additive contents.     

Unique sharp photoluminescence of size-controlled sonochemically synthesized zirconia nanoparticles

The present study explores the features of tetragonally stabilized polycrystalline zirconia nanophosphors prepared by a sonochemistry based synthesis from zirconium oxalate precursor complex. The sonochemically prepared pristine zirconia, 3 mol%, 5 mol% and 8 mol% yttrium doped zirconia nanophosphors were characterized using thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM) with energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and photoluminescence spectroscopy (PL). The reaction mechanism of formation of zirconia nanophosphors is discussed in detail. The probable sonochemical formation mechanism is being proposed. Stabilization of tetragonal phase of pristine zirconia even at room temperature was effectively established by controlling the particle size using ultrasonic waves. Improved phase purity and good surface morphology of the nanophosphors is being achieved via sonochemical route. FE-SEM micrographs reveal that the nanoparticles have uniform spherical shape and size. The narrow particle size distribution (∼15–25 nm) of the zirconia nanoparticles was found from FE-SEM statistical analysis and further confirmed by TEM. Zirconia nanophosphors exhibit a wide energy band gap and which was found to vary with yttrium dopant concentration. The highlight of the present study is the synthesis of novel nanocrystalline ZrO₂ and Y-ZrO₂ phosphor which simultaneously emits extremely sharp as well as intense UV, violet and cyan light on exciting the host atom. The yttrium ion dopant further enhances the photoluminescence property of zirconia. These nanocrystalline phosphors are likely to have remarkable optical applications as light emitting UV-LEDs, UV lasers and multi color displays.     

Computer simulation of defects and oxygen transport in yttria-stabilized zirconia

We have used molecular dynamics simulations and energy minimization calculations to examine defect energetics and oxygen diffusion in yttria-stabilized zirconia (YSZ). Oxygen vacancies prefer to be second nearest neighbors to yttrium dopants. The oxygen diffusion coefficient shows a peak at 8 mol% yttria consistent with experimental findings. The activation energy for oxygen diffusion varies from 0.6 to 1.0 eV depending on the yttria content. The Y_Zr′–V_O^··–Y_Zr′ complex with a binding energy of − 0.85 eV may play an important role in any conductivity degradation of YSZ.     

Fabrication of hollow thin films of yttria-stabilized zirconia by chemical vapor infiltration using NiO as oxygen source

Deposition of yttria-stabilized zirconia films on surface oxidized Ni wire substrate by chemical vapor infiltration (CVI) using ZrCl₄ and YCl₃ as metal sources and NiO as oxygen source were studied. The resultant films were cubic crystals of YSZ with a Y₂O₃ content of 1.0–3.7 mol%. The growth rate is larger than that obtained by conventional method of chemical vapor deposition (CVD), increased with the flow rate and decreased with diameter of NiO fiber. The growth rate above its thickness of 4 μm decreased with an increase in the oxidation temperature since the porosity of NiO wire might decrease with an increase in the oxidation temperature. Growth of YSZ films with the CVI method simultaneously involved CVD and electrochemical vapor deposition (EVD).     

Mechanoluminescence characterisation of γ-irradiated (KNa)Br:Ce3+ phosphor

The mechanoluminescence (ML) of γ-irradiated coloured powder of (KNa)Br:Ce(0.1–10 mol%) phosphor is reported in this paper. The samples are prepared by wet chemical method. The ML intensities are found to be dependent on concentrations of Ce³⁺ ion and γ-rays radiation dose. The variation of peak ML intensity of (KNa)Br:Ce(0.5 mol%) with different γ-rays dose is found as linear up to 2.5 kGy high dose from 0.08 kGy, whereas for the KBr:Ce(0.5 mol%) and NaBr:Ce(0.5 mol%) samples the ML intensities increases sublinearly. The prepared sample shows minimum fading in ML intensity. The ML characterisation shows the good linearity, less fading and simple ML glow curve structure, thus the prepared material may be useful for radiation dosimetry.     

Effect of Ni doping on the phase stability and conductivity of scandia-stabilized zirconia

The effect of Ni doping on the phase stability and conductivity of scandia-stabilized zirconia (SSZ) thick film was studied. A free-standing 10SSZ thick-film (10 mol% Sc₂O₃-stabilized zirconia, ~ 10 μm thick) that was previously in contact with a Ni layer during co-firing was fabricated. The 10SSZ thick-film showed a cubic phase in contrast to the rhombohedral phase shown for a bulk 10SSZ sample. The Ni content in the SSZ thick film was ~ 1.7 mol%. The effect of Ni on the cubic phase formation was also confirmed by the similar observation of the cubic phase in the Ni-doped bulk 10SSZ sample. The observed conductivity behavior also supported the XRD observation. Ni was found to hinder the transformation of the cubic phase to the rhombohedral on cooling in 10SSZ samples after a reduction treatment.     

Gadolinia-doped ceria films deposited by RF reactive magnetron sputtering

Gadolinia-doped ceria (GDC) films were prepared by RF reactive magnetron sputtering from a Gd-10 at.% Ce alloy target in reactive O₂/Ar gas mixtures and annealed at 700 °C for 2 h. Material characteristics and chemical compositions of GDC films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). Electrical behaviors were measured by AC impedance in the range of 500–700 °C at OCV for air condition. The microstructure of GDC films was found to be an assembly of columnar crystallites with a cubic fluorite structure. The total conductivity of 700 °C-annealed GDC (GDC-1) with the obtained composition of (Ce_0.911Gd_0.089)O_1.938 was higher than that of bulk yttria-stabilized zirconia (YSZ), but smaller than bulk GDC. The governing mechanism of conduction of sputtered-GDC electrolyte films was mainly governed by a grain boundary process, which resulted in a blocking effect and the lower conductivity of thin films than that of bulk GDC samples. Our results suggested that sputtered-GDC films with a comparable conductivity can be used as solid electrolyte layers for a solid oxide fuel cell (SOFC) system as compared to the well-known YSZ.     

Characterization of yttrium-doped ceria with various yttrium concentrations as cathode interlayers of SOFCs

This study focuses on enhancing the efficiency of solid oxide fuel cells (SOFCs) by modulating the thickness of the highly resistive solid solution layer of (Ce,Zr)O₂ formed between the yttria-stabilized zirconia (YSZ) electrolyte and the CeO₂-based interlayer on the cathode side. The effects of the concentration of dopant in CeO₂ on the thickness of the solid solution were analyzed. Yttrium-doped CeO₂ (YDC) interlayers were studied, with dopant concentrations in the range of 5–40 mol%. The results revealed that the thickness of the solid solution decreased with increasing dopant concentration up to 20 mol% and then saturated at higher dopant concentrations. In addition, the electrical conductivities of yttrium-doped ceria (YDC) and the solid solution of YSZ and YDC were measured. YDC with a dopant concentration of 20 mol% exhibited the highest conductivity. The conductivities of the YSZ/YDC solid solution decreased compared to those of YDC and YSZ for each dopant concentration, and the extent of the reductions was approximately the same for all dopant concentrations. These results indicate that a dopant concentration of 20 mol% is optimal to minimize the internal resistance of SOFCs when YDC is used as the interlayer material.     

Different conduction behaviors of grain boundaries in SiO2-containing 8YSZ and CGO20 electrolytes

Both doped zirconia and ceria have been widely recognized as promising electrolytes in solid oxide fuel cells (SOFC). Total conductivity is an important parameter to evaluate solid electrolytes. It is well know that the contribution to the total conductivity by grain boundaries is especially pronounced for SiO₂-contaminated electrolytes. In this study, we report on the different conduction behaviors of grain boundaries (GB) found in SiO₂-containing (impure) 8YSZ (8 mol% Y₂O₃-doped ZrO₂) and CGO20 (10 mol% Gd₂O₃-doped CeO₂) ceramics. In the grain size range (∼ 0.5–10 μm) studied, the GB conductivity of impure CGO20 ceramics constantly decreases with increasing grain size, in contrast to that observed in impure 8YSZ electrolytes whose GB conductivity increases almost linearly with grain size. It is also found that the variation in GB conductivity versus grain size is different from case to case, depending on the sintering/annealing conditions used to fabricate the ceramics. Two mechanisms were proposed to explain the GB behaviors of the impure 8YSZ and CGO20 ceramics. For doped ceria, the GB phases are supposed to be inert, which do not react with or dissolve into the matrix. Increasing sintering temperature leads to not only grain growth but also change in viscosity and wetting nature of the GB phases. These two factors promote further propagation of the GB phases along the grain boundaries, leading to an increased GB coverage fraction. For doped zirconia, however, the major factor dominating the GB conduction is the further dissolution of SiO₂ into zirconia lattice as a result of increase in sintering temperature or/and time. In addition, we will also evaluate and discuss the validities of the three models that are widely used to analyze the GB conduction in solid electrolytes.     

Picosecond pulse laser ablation of yttria-stabilized zirconia from kilohertz to megahertz repetition rates

Thin films of yttria stabilized zirconia were deposited onto silicon substrates using high repetition rate picosecond pulse lasers. The applied lasers covered the repetition rate range from 10 kHz to 4 MHz. We found that the laser pulse overlapping which results from increased repetition rates led to considerable changes in the ablation process. Defect formation and local heating lead to lower ablation thresholds and, with sufficiently high repetition rates, to melting of the target and even to thermal evaporation. We found that yttria-stabilized zirconia (YSZ) films deposited with picosecond pulses at 1064 nm wavelength below repetition rates of 2 MHz have rough, nanostructured morphology and the same atomic ratio of yttrium and zirconium as the target. Films deposited with 2 MHz and higher repetition rates with high number of overlapping pulses are very smooth, but are yttrium deficient, providing evidence of the importance of the thermal processes.     

Effect of Hydrolysis Conditions on the Direct Formation of Nanoparticles of Ceria–Zirconia Solid Solutions from Acidic Aqueous Solutions

The effect of the cation concentration, hydrolysis temperature, and composition in the CeO₂–ZrO₂ system on the direct precipitation of ceria–zirconia solid solutions and the structure of the precipitates from acidic aqueous solutions of (NH₄)₂Ce(NO₃)₆ and ZrOCl₂ by hydrolysis under hydrothermal conditions were investigated. Nanometer-sized (8–10 nm) ceria–zirconia solid solution particles in a composition range of 0 to 60 mol% ZrO₂ were directly precipitated from the solutions with total metal cation concentration less than 0.2 mol/dm³ by simultaneous thermal hydrolysis at 150–240°C. The crystalline phase of the precipitates gradually changed from cubic and/or tetragonal to monoclinic with increasing the cation concentration of the solution from 0.2 to 0.8 mol/dm³ at the starting composition of 50 mol% ZrO₂ under hydrolysis condition of 150°C for 48 h, which was attributed to decrease in the supply of hydrolyzed Ce component caused by decrease in the hydrolysis ratio of (NH₄)₂Ce(NO₃)₆. Ceria–zirconia solid solutions containing large amount of ZrO₂ maintained high specific surface area and small-sized crystallite after heat-treatment at 900–1000°C for 1 h.     

Surface segregation in yttria-stabilized zirconia by means of angle resolved X-ray photoelectron spectroscopy

Surface segregation of cations in undoped and titanium-doped yttria-stabilized zirconia was studied in air in the temperature range from 800 to 1400°C. Surface composition and distribution of the elements across the surface layer was examined using angle resolved X-ray photoelectron spectroscopy. The annealing procedure induced a silicon-rich surface layer of low zirconium concentration. The yttrium concentration only slightly increased at the surface. Enrichment factor of titanium in the titanium-doped yttria-stabilized zirconia was found to be higher than that of yttrium. No significant correlation between segregation of other cations was found.     

Fabrication, sintering and electrical properties of cobalt oxide doped Gd0.1Ce0.9O2 − δ

Ceria-based electrolytes have been widely researched in intermediate-temperature solid oxide fuel cell (SOFC), which might be operated at 500~600 °C. Gd0.1Ce0.9O1.95(GDC10) powders were prepared by a modified chemical co-precipitation process with Gd(NO3)3 and Ce(NO3)3 as precursors, and ammonia and hydrogen peroxide as precipitants. The precursors of GDC10 were fired at 350 °C for 2 h, then the fluorite structure cerias were identified by X-ray diffraction. The powders are well crystallized, with the size about 5 nm and surface area of 148.3 m2/g. Loading 1mol% cobalt oxide as additive, the GDC10 were succeeded to densify at 950 °C by liquid phase sintering mechanism. The grain size of 1CoGDC10 is small, about 100 nm. The electrical conductivity of samples sintered at 950 °C is about 0.01S/cm at 600 °C. The existence of cobalt oxide and smaller grain size of 1CoGDC10 don't affect the electrical conductivity.     

Large room temperature magnetoresistance in YSZ doped La0.67Ba0.33MnO3 composite

The temperature dependence of the resistivity for composite samples of (1−x)La_0.67Ba_0.33MnO₃+xYSZ(LBMO/YSZ) with different YSZ doping level of x has been investigated in a magnetic field range of 0-7000 Oe, where the YSZ represents yttria-stabilized zirconia (8 mol% Y₂O₃+92 mol% ZrO₂). With increasing YSZ doping level, the range of 0-10%, the metal-insulator transition temperature (T_P) decreases. However, the resistivity, specially the low temperature resistivity, increases. Results also show that the YSZ doping level has an important effect on a low field magnetoresistance (LFMR). In the magnetic field of 7000 Oe, a room temperature magnetoresistance value of 20% was observed for the composite with a YSZ doping level of 2%, which is encouraging for potential application of CMR materials at room temperature and low field.     

Influence of sintering conditions on the electrical properties of 10% ZrO2–10% Y2O3–CeO2 (mol%)

Yttria–zirconia doped ceria, 10% ZrO₂–10% Y₂O₃–CeO₂ (mol%) (CZY) and 0.5 mol% alumina-doped CZY (CZYA), prepared through oxide mixture process, were sintered by isothermal sintering (IS) and two-step sintering (TSS) having as variable the temperature and soaking time. The electrical conductivity of sintered samples was investigated in the 250 to 600 °C temperature range by impedance spectroscopy in air atmosphere. The microstructure was analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Alumina, as additive, improves the grain boundary conductivity of samples sintered at temperatures lower than 1500 °C. Concerning the sintering mode, two-step sintering (TSS) proved to be a good procedure to obtain CZYA samples with high electrical conductivity and density (> 95%) at relatively low sintering temperature and long soaking time.     

Pt nanoparticles supported over Ce–Ti–O: the solvothermal and photochemical approaches for the preparation of catalytic materials

Ce–Ti–O supports with different Ce/Ti molar ratios were synthesized by the solvothermal method using hexadecyltrimethylammonium bromide. Pt nanoparticles were then supported by photochemical deposition. The shape, size, and structure of these materials were analyzed by high-resolution transmission electron microscopy. The single CeO₂ support was also prepared, consisting of agglomerated cubic particles ranging from ~3 to 8 nm. When titania was combined with ceria, a nanostructured architecture was produced, evidencing the strong influence of Ti in the support structure. Photodeposition of Pt nanoparticles is more efficient on Ce–Ti–O supports than in pristine CeO₂. Crystalline Pt nanoparticles (mainly of ~2 to 4 nm) were detected. The catalytic properties of the materials were tested in the selective hydrogenation of cinnamaldehyde to cinnamyl alcohol. It was observed that Pt supported on Ce–Ti–O is more active and selective than Pt on CeO₂ or TiO₂ separately. The catalyst with 40 mol% Ce leads to total conversion of cinnamaldehyde in a few minutes; however, higher selectivity toward the desired product (cinnamyl alcohol) was obtained with higher amounts of Ce (50 mol%).     

Buffers for high temperature superconductor coatings. Low temperature growth of CeO2 films by metal–organic chemical vapor deposition and their implementation as buffers

Smooth, epitaxial cerium dioxide thin films have been grown in-situ in the 450–650°C temperature range on (001) yttria-stabilized zirconia (YSZ) substrates by metal–organic chemical vapor deposition (MOCVD) using a new fluorine-free liquid Ce precursor. As assessed by X-ray diffraction, transmission electron microscopy (TEM), and high-resolution electron microscopy (HREM), the epitaxial films exhibit a columnar microstructure with atomically abrupt film-substrate interfaces and with only minor bending of the crystal plane parallel to the substrate surface near the interface and at the column boundaries. With fixed precursor temperature and gas flow rate, the CeO₂ growth rate decreases from 10 Å/min at 450°C to 6.5 Å/min at 540°C. The root-mean-square roughness of the films also decreases from 15.5 Å at 450°C to 4.3 Å at 540°C. High-quality, epitaxial YBa₂C₃O_7−x films have been successfully deposited on these MOCVD-derived CeO₂ films grown at temperatures as low as 540°C. They exhibit T_c=86.5 K and J_c=1.08×10⁶ A/cm² at 77.4 K.     

Electrical properties of ZrO2-In2O3-Y2O3 and its application to a membrane for gas separation

Electrical properties of In₂O₃-doped yttria-stabilized zirconia (In-YSZ) were investigated. The solubility limit of In₂O₃ in YSZ (10 mol% Y₂O₃) is 17.5 mol%. The total conductivity depended on the concentration of In₂O₃. The activation energy of In-YSZ was higher than that of YSZ. From the oxygen partial pressure (P_o2) dependence of the total conductivity of In-YSZ, the electronic conductivity increased with increasing In₂O₃ concentration at low oxygen partial pressures and at high temperature. From the results, we discussed the applicability of In-YSZ to a membrane for hydrogen production from direct water splitting at high temperature.     

Fabrication of ceramic electrolytic films by the method of solution aerosol thermolysis (SAT) for solid oxide fuel cells (SOFC)

The technique of solution aerosol thermolysis (SAT) for the production of ceramic electrolytic films suitable for solid oxide fuels cells was investigated. The research has focused on the optimization of process parameters and characterization of the obtained films by means of X-ray diffractometry and scanning electron microscopy/energy-dispersive spectroscopy. Dense films of gadolinia-stabilized ceria of uniform thickness have been successfully produced on substrates consisting of dense disks of yttria-stabilized zirconia by SAT using nitrate salts of the precursors dissolved in an ethanol–water solvent. Substrate temperature is an important parameter and in this system the best initial values identified were of the order of 400–420 °C. The interplay between initial substrate temperature, solution flow rate, and postdeposition temperature is important for a good-quality film.     

Ultrasound assisted synthesis of doped TiO2 nano-particles: Characterization and comparison of effectiveness for photocatalytic oxidation of dyestuff effluent

The present work deals with the synthesis of titanium dioxide nanoparticles doped with Fe and Ce using sonochemical approach and its comparison with the conventional doping method. The prepared samples have been characterized using X-ray diffraction (XRD), FTIR, transmission electron microscopy (TEM) and UV–visible spectra (UV–vis). The effectiveness of the synthesized catalyst for the photocatalytic degradation of crystal violet dye has also been investigated considering crystal violet degradation as the model reaction. It has been observed that the catalysts prepared by sonochemical method exhibit higher photocatalytic activity as compared to the catalysts prepared by the conventional methods. Also the Ce-doped TiO₂ exhibits maximum photocatalytic activity followed by Fe-doped TiO₂ and the least activity was observed for only TiO₂. The presence of Fe and Ce in the TiO₂ structure results in a significant absorption shift towards the visible region. Detailed investigations on the degradation indicated that an optimal dosage with 0.8 mol% doping of Ce and 1.2 mol% doping of Fe in TiO₂ results in higher extents of degradation. Kinetic studies also established that the photocatalytic degradation followed the pseudo first-order reaction kinetics. Overall it has been established that ultrasound assisted synthesis of doped photocatalyst significantly enhances the photocatalytic activity.