Thermal,dielectric and conductivity studies on PVA/Ionic liquid [EMIM][EtSO4] based polymer electrolytes

Polymer electrolyte films of (PVA+15 wt% LiClO₄)+x wt% Ionic liquid (IL) 1-ethyl-3-methylimidazolium ethylsulfate [EMIM][EtSO₄] (x=0, 5, 10, 15) were prepared by solution cast technique. These films were characterized using TGA, DSC, XRD and ac impedance spectroscopic techniques. XRD result shows that amorphosity increases as the amount of the IL in PVA+salt (LiClO₄) is increased. DSC results confirm the same (except (PVA+15 wt% LiClO₄)+10 wt% IL). The dielectric and conductivity measurements were carried out on these films as a function of frequency and temperature. The addition of IL significantly improved the ionic conductivity of polymer electrolytes. Relaxation frequency vs. temperature plot for (PVA+15 wt% LiClO₄)+x wt% IL were found to follow an Arrhenius nature. The dielectric behavior was analyzed using real and imaginary parts of dielectric constant, dielectric loss tangent (tan δ) and electric modulus (M′ and M″).     

Research for improvement on the extract efficiency of lignans in traditional Chinese medicines by hybrid ionic liquids: As a case of Suhuang antitussive capsule

Recently, efficient extraction of natural products from traditional Chinese medicines (TCMs) by green solvents is deemed an essential area of green technology and attracts extensive attentions. In this work, a green protocol for simultaneous ultrasonic-extraction of the native compounds with different polarities of TCMs by using a hybrid ionic liquids (HILs)-water system was reported for the first time. As a case study, three superior ILs (1-ethyl-3-methylimidazolium tetrafluoroborate ([EMIM][BF4]), 1-ethyl-3-methylimidazolium acetate ([EMIM][OAc]), and 1-allyl-3-methylimidazolium chloride ([AMIM]Cl)) were chosen as the compositions of the HILs system, and the TCMs Suhuang antitussive capsule (SH) containing different-polarity lignans was selected. Primarily, an ultra-performance liquid chromatography coupled to triple quadrupole tandem mass spectrometry (UPLC-QqQ-MS/MS) method in the multiple reaction monitoring (MRM) mode was established for qualitative and quantitative analysis of 18 lignans. After majorization by uniform design experiment, the HILs prepared with [AMIM]Cl, [EMIM][BF4], and [EMIM][OAc] at a volume ratio of 1:5:5 could simultaneously extract multi-polarity lignans compared to single IL. Subsequently, the conditions of ultrasonic extraction employing with HILs and traditional organic solvent were optimized by the response surface methodology, respectively. The results indicated that the extract efficiency of the HILs system for target compounds was significantly improved compared with the traditional organic solvent-extraction, i.e. the content of total lignans in ethanol system was up to 47 mg/g, while that in the HILs system was up to 69 mg/g, with an increasing of 47%. Additionally, ¹H-NMR and ¹³C-NMR spectra were used to characterize the hydrogen-bond interactions in the HILs-lignan mixtures. Extraction with the HILs in TCMs is a new application schema of ILs, which not only avoids the use of volatile toxic organic solvents, but also shows the potential to be comprehensively applied for the extraction of bioactive compounds from TCMs.     

Sonoluminescence quenching and cavitation bubble temperature measurements in an ionic liquid

A comparison between the temperatures within imploding acoustic cavitation bubbles and the extent of sonoluminescence (SL) quenching by C₁–C₅ aliphatic alcohols in 1-ethyl-3-methylimidazolium ethylsulfate ([EMIM][EtSO₄], a well known imidazolium based room temperature ionic liquid (RTIL)), has been made at an ultrasound frequency of 213 kHz. The temperatures obtained ranged from 3500 ± 200 K, in neat [EMIM][EtSO₄], to about 3200 ± 200 K in RTIL-alcohol containing solutions. It was also found that the SL intensity decreased with increasing concentration (up to 1 M) of the alcohols to a greater extent compared with the relative changes to the bubble temperatures. Both the extent of the reduction in the bubble temperatures and the SL quenching were much smaller than those obtained in comparable aqueous solutions containing aliphatic alcohols. Possible reasons for the differences in the observed trends between water/alcohol and [EMIM][EtSO₄]/alcohol systems under sonication at 213 kHz are discussed.     

In situ solidification of ionic liquid [EMIM][EtOSO3] from melt under high pressure

In situ solidification of 1-ethyl-3-methylimidazolium ethyl sulfate [EMIM][EtOSO₃] from melt under high pressure has been investigated by using Raman spectroscopy. The results indicate that [EMIM][EtOSO₃] might experience a phase transition at about 2.4 GPa upon compression, which could be identified as solidification to a superpressurized glass by pressure broadening of the sharp ruby R₁ fluorescence line. Upon cooling, it solidifies as a glassy state rather than crystallizes at low temperature down to 93 K. These facts are suggestive of a phase transition of liquid to a superpressurized glass induced by compression in [EMIM][EtOSO₃], which is similar to the glassy state at low temperature.     

Effects of compositions on properties of PEO–KI–I2 salts polymer electrolytes for DSSC

The effects of compositions on properties of PEO/KI/I₂ salts polymer electrolytes were investigated to optimize the photovoltaic performance of solid state DSSCs. XRD pattern for the mole ratio 12:1 of [EO:KI] was showed the formation of complete amorphous complex. DSC results also confirmed the amorphous nature of the polymer electrolyte. The highest value of ionic conductivity is 8.36 × 10^− 5 S/cm at 303 K (ambient temperature) and 2.32 × 10^− 4 S/cm at 333 K (moderate temperature) for the mole ratio 12:1 of EO:KI complex. The effect of contribution of [I⁻] and [I₃⁻] concentration with conductivity were also evaluated. FTIR spectrum reveals that the alkali metal cations were co-ordinated to ether oxygen of PEO. The formation of polyiodide ions, such as symmetric I₃⁻ (114 cm^− 1) and I₅⁻ (145 cm^− 1) caused by the addition of iodine was confirmed by FT Raman spectroscopic measurements. The optimum composition of PEO–KI–I₂ polymer electrolyte system for higher conductivity at ambient and moderate temperatures was reported. A linear Arrhenius type behaviour was observed for all the PEO–KI polymer complexes. Transport number measurements were carried out for several polymer electrolyte compositions. Dye-sensitized solar cells were fabricated by using higher conductivity polymer electrolyte compositions and its photoelectrochemical performance was investigated. The fill factor, short-circuit current, photovoltage and energy conversion efficiency of the DSSC assembled with optimized electrolyte composition were calculated to be 0.563, 6.124 mA/cm², 593 mV and 2.044% respectively.     

Organic dopant added polyvinylidene fluoride based solid polymer electrolytes for dye-sensitized solar cells

The effect of phenothiazine (PTZ) as dopant on PVDF/KI/I₂ electrolyte was studied for the fabrication of efficient dye-sensitized solar cell (DSSC). The different weight percentage (wt%) ratios (0, 20, 30, 40 and 50%) of PTZ doped PVDF/KI/I₂ electrolyte films were prepared by solution casting method using DMF as a solvent. The following techniques such as Fourier transform infrared (FT-IR), differential scanning calorimetry (DSC), X-ray diffractometer (XRD) and AC-impedance analysis have been employed to characterize the prepared polymer electrolyte films. The FT-IR studies revealed the complex formation between PVDF/KI/I₂ and PTZ. The crystalline and amorphous nature of polymer electrolytes were confirmed by DSC and XRD analysis respectively. The ionic conductivities of polymer electrolyte films were calculated from the AC-impedance analysis. The undoped PVDF/KI/I₂ electrolyte exhibited the ionic conductivity of 4.68×10⁻⁶ S cm⁻¹ and this value was increased to 7.43×10⁻⁵ S cm⁻¹ when PTZ was added to PVDF/KI/I₂ electrolyte. On comparison with different wt% ratios, the maximum ionic conductivity was observed for 20% PTZ-PVDF/KI/I₂ electrolyte. A DSSC assembled with the optimized wt % of PTZ doped PVDF/KI/I₂ electrolyte exhibited a power conversion efficiency of 2.92%, than the undoped PVDF/KI/I₂ electrolyte (1.41%) at similar conditions. Hence, the 20% PTZ-PVDF/KI/I₂ electrolyte was found to be optimal for DSSC applications.     

Ionic liquid type dye-sensitized solar cells: increases in photovoltaic performances by adding a small amount of water

Increases in photovoltaic performances for dye-sensitized solar cells having ionic liquid type electrolytes are reported. These results are explained by diffusion coefficient for I₃⁻, charge transfer resistances on counter electrodes, flat band potentials of TiO₂, redox potentials for I⁻/I₃⁻, electron diffusion constants, electron life time, and diffusion length in TiO₂ layers. Methylpropylimidazolium iodide is selected because of the lowest viscosity and the highest conductivity. Increases in the photovoltaic performance are observed when a small amount of water was added into the ionic liquid consisting of both LiI and t-butylpyridine as the additives. These improvements are brought about by enhancements of all of J_sc, ff and V_oc. The increases in J_sc and ff are associated with the decrease in charge transfer resistances on counter electrodes and increases in ionic conductivities. V_oc may be explained by an increase in the difference between redox potentials of I⁻/I₃⁻ and Fermi level.     

Synthesis and characterization of proton-conducting polymer electrolyte based on polyacrylonitrile (PAN)

Solid polymer electrolytes based on polyacrylonitrile (PAN) doped with ammonium iodide (NH₄I) have been prepared by solution casting method with different molar ratios of polymer and salt using DMF as solvent. The XRD pattern confirms the dissociation of salt. The FTIR analysis confirms the complex formation between the polymer and the salt. A shift in glass transition temperature (T _g ) of the PAN/NH₄I electrolytes has been observed from the DSC thermograms, which indicates the interaction between the polymer and the salt. The conductivity analysis shows that the polymer electrolyte with 20 mol% NH₄I has the highest conductivity equal to 1.106 × 10⁻³ S cm⁻¹ at room temperature. The activation energy (E _a ) has been found to be low for the highest conductivity sample. The dielectric permittivity (ε*) and modulus (M*) have been calculated from the alternating current (AC) impedance spectroscopy in the frequency range 42 Hz–1 MHz. The DC polarization measurement shows that the conductivity is mainly due to ions.

     

Preparation and properties of a gel polymer electrolyte system based on poly-ε-caprolactone containing 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

Gel polymer electrolytes (GPE) obtained by immobilizing a solution of zinc triflate (ZnTr) in an ionic liquid, namely 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [emim][Tf₂N] within a biodegradable polymeric matrix of poly-ε-caprolactone (PCL) were prepared by a simple solvent cast technique for different concentrations of the ionic liquid. The electrolyte with the composition 75 wt% PCL: 25 wt% ZnTr+100 wt% [emim][Tf₂N] showed the highest ionic conductivity of 1.1×10⁻⁴ S cm⁻¹ at 25 °C and favored by the rich amorphous phase of the GPE as confirmed from room temperature X-ray diffraction analysis (XRD). The morphology of the GPE was examined using scanning electron microscopy (SEM) which revealed the homogeneity of the prepared GPE system. The temperature dependence of electrical conductivity of the GPE followed the Arrhenius behavior. The Zn²⁺ ionic transport number has been determined to be ~0.62 which denotes the predominant contribution of zinc ion towards total ionic conductivity. The electrochemical stability window of GPE is found to be 2.5 V with a thermal stability upto 200 °C. This eco-friendly and safe electrolyte may be used to fabricate compostable batteries, in future, with a suitable selection of other components of the battery system.     

High ionic conductive behavior of cyanoethylated polyvinylalcohol- and polyacrylonitrile-based electrolytes

New type polymer electrolyte films based on poly(acrylonitrile), (PAN), and cyanoethylated poly(vinyl alcohol), (CN-PVA), were prepared and their conducting behaviors were investigated. CN-PVA was prepared from poly(vinyl alcohol), (PVA) and acrylonitrile in the presence of sodium hydroxide and quaternary ammonium halide as a phase transfer catalyst. Free standing PAN- and CN-PVA-based electrolyte films were prepared by casting the propylene carbonate (PC) solution containing PAN, CN-PVA and LiClO₄ and removing some amount of PC. Ionic conductivity of the electrolyte film, (PAN)10(CN-PVA) 10(LiClO₄)8(PC)4 composite film was 14.6 mS cm^− 1 at 30 °C and 22.4 mS cm^− 1 at 60 °C. FTIR results for the electrolyte films suggest that the nitrile groups in the CN-PVA matrix mainly interact with the lithium ions in the films and enhance dissolution of the lithium salt in the electrolyte films.     

Sonochemical nitrogen fixation for the generation of NO2− and NO3− ions under high-powered ultrasound in aqueous medium

Sonochemical species such as nitrite (NO₂⁻) and nitrate (NO₃⁻) were detected in ultrapure aqueous medium with 28 kHz low frequency ultrasound (US) in the range of 200–1200 W output power. The concentration of their anionic ions monitored with a high-performance liquid chromatography increased with increasing US power especially under air atmosphere. When the generation of NO₂⁻ and NO₃⁻ ions under US exposure was investigated for N₂, O₂ and Ar-bubbled solutions, no trace of NO₂⁻ was observed while NO₃⁻ was slightly generated. Under air atmosphere, the concentration of dissolved oxygen in the aqueous medium increased especially when 1200 W power was used. In addition, the bulk pH shifted towards the acidic side with an increase in exposure time, which indicated that NO₂⁻ was formed. The formation of oxidizing species under 28 kHz low frequency ultrasonic treatment was confirmed with an absorption spectrum which was dominated by two maxima peaks at 288 nm and 352 nm representing triiodide I₃⁻ anion.     

Synthesis of nitrogen doped graphite oxide and its electrochemical properties

We herein report a synthesis nitrogen-doped graphite oxide (N-doped GO) by heat treatment with melamine. The N-doped GO contains 4 at % of nitrogen, incurring the oxygen reduction reaction by nitrogen functional groups. Two kinds of aqueous electrolytes are used for finding the electrocatalytic activities, resulting in symmetric oxygen reduction reaction peaks at −0.8 and 0 V in 6 M KOH and 1 M H₂SO₄ electrolytes, respectively. The N-doped GO is more activated in the acid electrolyte compared to thermally reduced graphite oxide (TrGO). Specific volumetric capacitance of N-doped GO in 1.8 M tetraethylmethylammonium tetrafluoroborate electrolyte is 57.4 F cc⁻¹ which is higher than 30.5 F cc⁻¹ of the TrGO, demonstrating positive effects of the nitrogen doping in the organic electrolytes for the energy storage devices.     

Effects of plasticizer and nanofiller on the dielectric dispersion and relaxation behaviour of polymer blend based solid polymer electrolytes

Solid polymer electrolytes consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend (50:50 wt/wt%) with lithium triflate (LiCF₃SO₃) as a dopant ionic salt at stoichiometric ratio [EO + (CO)]:Li⁺ = 9:1, poly(ethylene glycol) (PEG) as plasticizer (10 wt%) and montmorillonite (MMT) clay as nanofiller (3 wt%) have been prepared by solution cast followed by melt–pressing method. The X–ray diffraction study infers that the (PEO–PMMA)–LiCF₃SO₃ electrolyte is predominantly amorphous, but (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG electrolyte has some PEO crystalline cluster, whereas (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG–3 wt% MMT electrolyte is an amorphous with intercalated and exfoliated MMT structures. The complex dielectric function, ac electrical conductivity, electric modulus and impedance spectra of these electrolytes have been investigated over the frequency range 20 Hz to 1 MHz. These spectra have been analysed in terms of the contribution of electrode polarization phenomenon in the low frequency region and the dynamics of cations coordinated polymer chain segments in the high frequency region, and also their variation on the addition of PEG and MMT in the electrolytes. The temperature dependent dc ionic conductivity, dielectric relaxation time and dielectric strength of the plasticized nanocomposite electrolyte obey the Arrhenius behaviour. The mechanism of ions transportation and the dependence of ionic conductivity on the segmental motion of polymer chain, dielectric strength, and amorphicity of these electrolytes have been explored. The room temperature ionic conductivity values of the electrolytes are found ∼10⁻⁵ S cm⁻¹, confirming their use in preparation of all-solid-state ion conducting devices.     

Effect of different compositions of ethylene carbonate and propylene carbonate containing iodide/triiodide redox electrolyte on the photovoltaic performance of DSSC

The effect of different compositions (in weight percent) of ethylene carbonate (EC) and propylene carbonate (PC) containing iodide/triiodide redox electrolyte on the photoelectrochemical performance of N719-sensitized nanocrystalline TiO₂ solar cell was studied. The cells consisted of 0.6 M 1-hexyl-2,3-dimethylimidazolium iodide, 0.1 M LiI, 0.05 M I₂ and 0.5 M 4-tert-butylpyridine in different compositions such as 1:1, 1:2, and 2:1 wt% of EC and PC. In 1:1 wt% of EC and PC containing redox electrolyte, short circuit photocurrent density (J _sc) increased and open circuit voltage (V _oc) decreased. But in 1:2 and 2:1 wt% of EC and PC containing redox electrolytes, V _oc increased and J _sc decreased but fill factor remained relatively constant. Dye-sensitized solar cells (DSSCs) prepared using these electrolytes give a short circuit photocurrent densities of 16.86, 12.71, and 12.09 mA/cm²; an open circuit voltages of 0.73, 0.78, and 0.79 V; fill factors of 0.63, 0.64, and 0.64; and an overall conversion efficiencies of 7.76, 6.34, and 6.13 % at an incident light of 100 mWcm^?2 for 1:1, 2:1, and 1:2 wt% of EC/PC containing redox electrolytes, respectively. The incident photon-to-current conversion efficiency was higher in the case of 1:1 wt% of EC and PC containing redox electrolyte than 1:2 and 2:1 wt% of EC and PC containing redox electrolyte. It revealed that 1:1 wt% of EC and PC containing iodide/triiodide redox electrolyte is an effective electrolyte system for the fabrication of long-term stable DSSC.     

Polyethylene oxide and ionic liquid-based solid polymer electrolyte for rechargeable magnesium batteries

Solid polymer electrolytes (SPEs) based on polyethylene oxide (PEO) complexed with magnesium triflate Mg(Tf)₂ or Mg(CF₃SO₃)₂) and incorporating the ionic liquid (IL) (1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR₁₄TFSI)) were prepared by solution cast technique. The electrolyte was optimized and characterized using electrical conductivity, cationic transport number measurements, and cyclic voltammetry. The highest conductivity of the PEO/Mg(Tf)₂, 15:1 (molar ratio), electrolyte at room temperature was 1.19 × 10⁻⁴ S cm⁻¹ and this was increased to 3.66 × 10⁻⁴ S cm⁻¹ with the addition of 10 wt.% ionic liquid. A significant increase in the Mg²⁺ ion transport number was observed with increasing content of the ionic liquid in the PEO-Mg(Tf)₂ electrolyte. The maximum Mg²⁺ ion transport number obtained was 0.40 at the optimized electrolyte composition. A battery of the configuration Mg/ and [(PEO)₁₅:Mg(Tf)₂+10%IL]/TiO₂-C was assembled and characterized. Preliminary studies showed that the discharge capacity of the battery was 45 mA h g⁻¹.

     

Redox behaviour,chemical compatibility and electrochemical performance of Sr2MgMoO6 − δ as SOFC anode

The double perovskite Sr₂MgMoO_6 − δ (SMM) has been proposed as a potential anode material for direct hydrocarbon oxidation in solid oxide fuel cells (SOFCs). The oxygen nonstoichiometry and electrical conductivity dependence of Sr₂MgMoO_6 − δ have been determined as a function of the oxygen partial pressure by coulometric titration and impedance spectroscopy techniques. The chemical compatibility of Sr₂MgMoO_6 − δ with most of the typical electrolytes commonly used in SOFCs i.e. La_0.8Sr_0.2Ga_0.8Mg_0.2O_3 − δ (LSGM), Ce_0.8Gd_0.2O_2 − δ (CGO) and Zr_0.84Y_0.16O_2 − δ (YSZ), was investigated. Reactivity between SMM and all these electrolytes has been found above 1000 °C, although the reaction is most severe with ZrO₂-based electrolytes. Area-specific polarisation resistance of the SMM/LSGM/SMM symmetrical cells indicates that the polarisation resistance increases with the firing temperature of the electrodes due to chemical interaction between LSGM and SMM layers. A CGO buffer layer between the anode and electrolyte was also used to prevent an excessive interdiffusion of ionic species between these components, resulting in better performance. Power densities of 330 and 270 mW cm^− 2 were reached at 800 °C for SMM/CGO/LSGM/LSCF and SMM/LSGM/LSCF electrolyte-supported cells, respectively; with 600-μm-thick LSGM electrolyte, using humidified H₂ as fuel and air as oxidant. XPS and XRPD studies on SMM powders annealed in air and diluted CH₄ atmospheres showed that the surface of SMM powders is mainly formed by SrMoO₄ and metal carbonates.     

New type of inorganic–organic hybrid (heteropolytungsticacid–polyepichlorohydrin) polymer electrolyte with TiO2 nanofiller for solid state dye sensitized solar cells

A new type of inorganic–organic hybrid solid state polymer electrolyte consisting of heteropolytungsticacid impregnated polyepichlorohydrin with iodine/iodide and TiO₂ nanofiller have been prepared for their potential application in dye sensitized solar cells. The prepared polymer electrolytes were well characterized by FT-IR, Scanning electron microscopy (SEM), X-ray diffraction (XRD), Electrochemical Impedance analysis (EIS) and Thermal analysis (TGA). The prepared polymer electrolyte with TiO₂ nanofiller shows reasonable ionic conductivity (20.4 × 10⁻⁶ S cm⁻¹) compared to pure polyepichlorohydrin (2.0 × 10⁻⁹ S cm⁻¹) at ambient temperature. The presence of negatively charged redox species heteropolytungsticacid in the polymer matrix prevents the photo reduction of iodide (back electron transfer) and the presence of TiO₂ nanofiller increases the degree of amorphousity of the polymer which in turn prolongs the stability of the fabricated dye sensitized solar cell over a long period compared to bare polymer electrolyte.     

Ionic association and conductance of ionic liquids in dichloromethane at temperatures from 278.15 to 303.15 K

The electrical conductances of very dilute solutions of the ionic liquids 1-ethyl-3-methylimidazolium tetrafluoroborate [emim][BF₄] and 1-butyl-3-methylimidazolium tetrafluoroborate [bmim][BF₄] in the low-permittivity solvent dichloromethane have been measured in the temperature range from 278.15 to 303.15 K at 5 K intervals. The data was analyzed assuming the possible presence of contact (CIP) and solvent-separated (SSIP) ion pairs in the solution on the basis of lcCM model to obtain ionic association constants, K _A, and the limiting molar conductivities, Λ_o, of these electrolytes. The examined ionic liquids are strongly associated in dichloromethane over the whole temperature range. From the temperature dependence of the limiting molar conductivities, the Eyring’s activation enthalpy of charge transport was determined. The thermodynamic functions such as Gibbs energy, entropy, and enthalpy of the process of ion pair formation were calculated from the temperature dependence of the association constants.     

Electrical studies on ionic liquid-based gel polymer electrolyte for its application in EDLCs

Ionic liquid-based gel polymer electrolyte (GPE) has been synthesized using standard solution cast technique. Different weight percent of ionic liquid, 1-Butyl-3-methylimidazolium chloride (BMIMCl) and liquid electrolyte, ethylene carbonate (EC)–propylene carbonate (PC)–tetra ethyl ammonium tetra fluoro borate (TEABF₄) was incorporated in polymer, poly(vinylidene fluoride-co-hexafluoro propylene (PVdF-HFP) to obtain mechanically stable gel polymer electrolyte film (GPE) having maximum conductivity of ~10⁻³ S cm⁻¹ at room temperature, which is acceptable from device fabrication point of view. Potential window and ionic transference number has been obtained to examine the potential limit and ionic characteristics of optimized GPE system. Temperature dependence behavior of electrical conductivity curve follows Arrhenius nature in the temperature range of 303–373 K. Pattern of dielectric constant and its loss as a function of frequency and temperature have been studied and is being explained on the basis of electrode interfacial polarization effect. Frequency-dependent conductivity spectra obey the Jonscher’s power law. Further, optimized composition of GPE has been tested successfully for its application in supercapacitor fabrication with activated charcoal as an electrode material. Maximum specific capacitance of 118.6 mF cm⁻² equivalent to single electrode specific capacitance of 61.7 F g⁻¹ have been observed for the optimized GPE film.

     

Influences of LiCF3SO3 and TiO2 nanofiller on ionic conductivity and mechanical properties of PVA:PVdF blend polymer electrolyte

In recent years, solid polymer electrolytes have been extensively studied due to its flexibility, electrochemical stability, safety, and long life for its applications in various electrochemical devices. Interaction of LiCF₃SO₃ and TiO₂ nanofiller in the optimized composition of PVA:PVdF (80:20—system-A possessing σ ~ 2.8 × 10⁻⁷ Scm⁻¹ at 303 K) blend polymer electrolyte have been analyzed in the present study. LiCF₃SO₃ has been doped in system-A, and the optimized LiCF₃SO₃ doped sample (80:20:15-system-B possessing σ ~ 2.7 × 10⁻³ Scm⁻¹ at 303 K) has been identified. The effect of different concentration of TiO₂ in system-B has been analyzed and the optimized system is considered as system-C (σ ~ 3.7 × 10⁻³ Scm⁻¹ at 303 K). The cost effective, solution casting technique has been used for the preparation of the above polymer electrolytes. Vibrational, structural, mechanical, conductivity, thermal, and electrochemical properties have been studied using FTIR, XRD, stress-strain, AC impedance spectroscopic technique, DSC and TGA, LSV, and CV respectively to find out the optimized system. System-C possessing the highest ionic conductivity, higher tensile strength, low crystallinity, high thermal stability, and high electrochemical stability (greater than 5 V vs Li/Li⁺) is well suitable for lithium ion battery application.