Band overlap via chemical pressure control in double perovskite (Sr2−xCax)FeMoO6 (0 ⩽ x ⩽ 2.0) with TMR effect

The chemical pressure control in (Sr_2−xCa_x)FeMoO₆ (0 ⩽ x ⩽ 2.0) with double perovskite structure has been investigated systematically. We have performed first-principles total energy and electronic structure calculations for x = 0 and x = 2.0. The increasing Ca content in (Sr_2−xCa_x)FeMoO₆ samples increases the magnetic moment close to the theoretical value due to reduction of Fe/Mo anti-site disorder. An increasing Ca content results in increasing (Fe²⁺ + Mo⁶⁺)/(Fe³⁺ + Mo⁵⁺) band overlap rather than bandwidth changes. This is explained from simple ionic size arguments and is supported by X-ray absorption near edge structure (XANES) spectra and band structure calculations.     

Electrical conductivity and oxygen permeation properties of SrCoFeOx membranes

The total conductivity and oxygen permeation properties of dense SrCoFeO_x membranes synthesized from the solid state method were studied in the temperature range of 700–900 °C. The SrCoFeO_x membranes consist of an intergrowth (Sr₄Fe_6 − xCo_xO_13 ± δ), perovskite (SrFe_1 − xCo_xO_3 − δ), and spinel (Co_3 − xFe_xO₄) phase. SrCoFeO_x exhibits n-type and p-type conduction at low and high oxygen partial pressures, respectively, and has a total conductivity of 16.5 S/cm at 900 °C in air. The oxygen permeation fluxes for SrCoFeO_x and SrFeCo_0.5O_x membranes were measured with either an inert or carbon monoxide sweep gas. The oxygen permeation fluxes were higher through SrCoFeO_x membranes than SrFeCo_0.5O_x membranes and can be attributed to a difference in the amount and makeup of the perovskite phase present in each composition. The oxygen permeation fluxes with a carbon monoxide sweep gas were approximately two orders of magnitude larger than the fluxes measured with an inert sweep gas for both compositions. The large oxygen permeation fluxes observed with a carbon monoxide sweep are due to a higher driving force for oxygen transport and a reaction on the sweep side of the membrane that maintains a low oxygen partial pressure.     

Mixed conducting perovskite-like ceramics on the base of lanthanum gallate

Ceramic perovskite solid solutions (La_0.9Sr_0.1)[(Ga_1−xM_x)_0.8Mg_0.2]O_3−y, 0 ≤ x ≤ 0.5, M = Fe, Ni, Cr (systems I–III) and brownmillerite solid solutions (La_0.2Sr_1.8)[Ga(Fe_1−xMg_x)]O_5−z, 0 ≤ x ≤ 0.5, (system IV) have been prepared. The samples have been studied by X-ray diffraction and electron microscopy methods, dielectric spectroscopy and permeability measurements. The correlation between the composition, unit cell parameter changes, electrical transport and oxygen permeation properties has been revealed. Introduction of transition metals (Fe, Ni, or Cr), substituting for gallium, ensures the enhancement of the electronic constituent of the conductivity in the perovskite systems I–III. Stabilization of the transition metal high valence states 4+ or 5+ has been suggested for compositions I and III. This leads to a unit cell volume contraction and provides a decrease in the concentration of oxygen vacancies. The oxygen permeability reaches its maximum values in compositions I–III with x ∼ 0.3. On the contrary, increasing concentration of the doping element with lower valence state (magnesium), substituting for iron, determines the expansion of the brownmillerite unit cell volume and provides an increase of the oxygen vacancy concentration, which in turn, favors the enhancement of oxygen permeability of composition IV.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

Electrical conductivity and thermal expansion of La0.8Sr0.2(Mn,Fe,Co)O3-δ perovskites

La_1−xSr_xMeO₃ (Me = Mn, Co, Fe) perovskites are used as cathodes and are also attractive materials for application as the contact layer between cathode and interconnect in solid oxide fuel cells. In this contribution, three perovskite series, La_0.8Sr_0.2Mn_1−xCo_xO_3-δ (series 1), La_0.8Sr_0.2Fe_1−xCo_xO_3-δ (series 2) and La_0.8Sr_0.2Mn_1−x/2Fe_(1−x)/2Co_xO_3-δ (series 3) with x = 0, 0.25, 0.5, 0.75 and 1 were re-investigated under identical synthesis and measurement conditions with the aim of obtaining a full overview of the quasi-ternary system La_0.8Sr_0.2MnO_3-δ–La_0.8Sr_0.2FeO_3-δ–La_0.8Sr_0.2CoO_3-δ. The distribution of the different crystallographic phases in the selected series, the DC electrical conductivity and the thermal expansion coefficients are presented.     

Electrical conductivity of (Ba0.3Sr0.2La0.5)(In1−xFex)O3−δ

We have synthesized the perovskite oxides of the (Ba_0.3Sr_0.2La_0.5)(In_1−xFe_x)O_3−δ system and measured the total electrical conductivity as a function of temperature and oxygen partial pressure. It was found that the single-phase composition region extended from x = 0.0 to x = 1.0, and that the Fe valence increased from 3.06 to 3.50 in that region. The electrical conductivity was semiconducting from x = 0.0 to x = 0.40 and metallic from x = 0.50 to x = 1.0. The total electrical conductivity at 800 °C also increased with the Fe content and achieved a maximum value of 140 (S/cm) at x = 1.0. From the dependence of the electrical conductivity on the oxygen partial pressure, we conclude that above x = 0.50, the majority carriers are holes. The estimated hole conductivity increased exponentially with the amount of Fe⁴⁺ cation present. The oxide ion conductivity was dependent on the oxygen vacancy content.     

Structural stability and oxygen permeability of cerium lightly doped BaFeO3−δ ceramic membranes

The structural stability under reducing environment and oxygen permeation fluxes of perovskite-type BaCe_xFe_1−xO_3−δ (0 ≤ x ≤ 0.15) ceramic membranes were investigated. The XRD results showed that 5% of cerium doping into the perovskite B-site can make the BaFeO_3−δ transform from the hexagonal structure to the cubic structure, and make the structure stable under 10% H₂–Ar mixed gas at 900 °C for 1 h, but breaks down after 5 h. Lattice parameters and oxygen non-stoichiometry of the as-prepared and reduced samples were measured. Oxygen permeation fluxes of the membranes were measured between 700 and 950 °C. Oxygen permeation during the cooling and heating circles showed that 5% of cerium doping into the perovskite B-site can avoid the phase transformation. The optimum cerium-doped amount on the B-sites was found to be 10%.     

Structure and oxygen stoichiometry of SrCo0.8Fe0.2O3−δ and Ba0.5Sr0.5Co0.8Fe0.2O3−δ

High temperature X-ray diffraction (HT-XRD), temperature programmed desorption (TPD), thermogravimetric analysis–differential thermal analysis (TGA/DTA) and neutron diffraction were combined to determine the structure and oxygen stoichiometry of SrCo_0.8Fe_0.2O_3−δ (SCF) and Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCF) up to 1273 K in the pO₂ range of 1 to 10^− 5 atm. Formation of the vacancy-ordered brownmillerite phase, SrCo_0.8Fe_0.2O_2.5, was observed as a region of zero oxygen release in the TPD measurements and confirmed by HT-XRD and TGA/DTA. No ordering was observed in the BSCF system by any of the techniques utilized in this work. The oxygen vacancy concentration of BSCF was found to be considerably higher than that of SCF and always higher than that of the ordered brownmillerite phase of SCF, δ = 0.5. The combination of a high vacancy concentration and absence of ordering leads to higher oxygen permeation fluxes through BSCF membranes in comparison to SCF.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Thermal and chemical expansion of mixed conducting La0.5Sr0.5Fe1−xCoxO3−δ materials

Oxygen deficiency, thermal and chemical expansion of La_0.5Sr_0.5Fe_1−xCo_xO_3−δ (x = 0, 0.5, 1) have been measured by thermogravimetry, dilatometry and high temperature X-ray diffraction. The rhombohedral perovskite materials transformed to a cubic structure at 350 ± 50 °C. The thermal expansion of the materials up to the onset of thermal reduction was 14–18 × 10^− 6 K^− 1. Above 500 °C in air (400 °C in N₂), chemical expansion contributed to the thermal expansion and the linear thermal expansion coefficients were significantly higher, 16–35 × 10^− 6 K^− 1. The chemical expansion, ε_c, showed a maximum of 0.0045 for x = 0.5 and 0.0041 for x = 1 at 800–900 °C. The normalized chemical expansion, ε_c/Δδ, was 0.036 for x = 0.5 and 0.035 for x = 1 at 800 °C. The chemical expansion can be correlated with an increasing ionic radius of the transition metals with decreasing valence state.     

Structure and electrochemical properties of Sm0.5Sr0.5Co1 − xFexO3 − δ cathodes for solid oxide fuel cells

Crystal structure, thermal expansion coefficient, electrical conductivity and cathodic polarization of compositions in the system Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ with 0 ≤ x ≤ 0.9 were studied as function of Co / Fe ratio and temperature, in air. Two phases, including an Orthorhombic symmetry for 0 ≤ x ≤ 0.4 and a cubic symmetry for 0.5 ≤ x ≤ 0.9, were observed in samples of Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ at room temperature. The adjustment of thermal expansion coefficient (TEC) to electrolyte, which is one of the main problems of SSC, could be achieved to lower TEC values with more Fe substitution. High electrical conductivity above 100 S/cm at 800 °C was obtained for all specimens, so they could be good conductors as cathodes of IT-SOFC. The polarization behavior of SSCF as a function of Fe content was evaluated by means of AC impedance using LSGM electrolyte. It was discovered that the Area Specific Resistance (ASR) of SSCF increased as the amount of substitution of Fe for Co increased. When the amount of Fe reached to 0.4, the highest ASR was obtained and then the resistance started decreasing above that. The electrode with a composition of Sm_0.5Sr_0.5Co_0.2Fe_0.8O_3 − δ showed high catalytic activity for oxygen reduction operating at temperature ranging from 700 to 800 °C.     

High temperature properties of the n = 2 Ruddlesden–Popper phases (La,Sr)3(Fe,Ni)2O7−δ

The crystal chemistry and mixed conductor properties of the n = 2 member of the Ruddlesden–Popper (R–P) phases Sr_3−xLa_xFe_2−yNi_yO_7−δ with 0 ≤ x ≤ 0.3 and 0 ≤ y ≤ 1.0 have been studied at high temperature. High-temperature X-ray diffraction and thermogravimetric measurements of the equilibrium pO₂ (10^− 5 ≤ pO₂ ≤ 1 atm) in the temperature range 400 ≤ T ≤ 1000 °C indicate that the Sr₃FeNiO_7−δ phase is able to accommodate a large oxygen non-stoichiometry (δ ∼ 1.5) without structural transformations. The electrical conductivity and oxygen permeability increase with the substitution of Ni for Fe in the range 550 ≤ T ≤ 1000 °C. The electrical transport of the Sr₃FeNiO_7−δ phase is thermally activated and the activation energy decreases with the substitution of Ni for Fe for a given oxygen content. The increase in the oxygen permeation flux with increasing Ni content is due to an increasing oxygen non-stoichiometry and a lower activation energy for permeation.     

Transport properties and phase stability of mixed conducting oxide membranes

At high strontium doping levels, perovskite oxides containing iron have suitable stability and transport properties for use as oxide ion transport membranes. In our studies of these materials, we have investigated the pO₂ and temperature dependence of the conductivity and non-stoichiometry of La_1−xSr_xFe_1−yM_yO_3−δ (M = Cr, Ti) by using electrochemical cells and the thermal expansion by dilatometry. Non-equilibrium behavior is observed in both the chemical expansion data and also in the conductivity and stoichiometry and suggests the occurrence of microscopic phase segregation on reduction. Analysis of the microstructure of quenched samples confirms the occurrence of local phase separation. Bulk diffusion and surface exchange coefficients under near-gradientless conditions have been determined by the electrical conductivity relaxation (ECR) technique and by isotope exchange depth profiling (IEDP). Evaluation of transport under a chemical gradient was accomplished by transient isotopic tracing of operating membranes. The isotope transients (¹⁶O₂–¹⁸O₂) were performed on tubular membranes operating at steady state at temperatures between 1023 K and 1173 K and allow an unambiguous separation of surface and bulk resistances to oxygen permeation under steady state conditions, a separation not possible by permeation measurements alone.     

LFN and LSCFN perovskites — structure and transport properties

Structural, electronic and transport properties of LFN (LaFe_1−zNi_zO₃) and LSCFN (La_1−xSr_xCo_1−y −zFe_yNi_zO₃) perovskites synthesized by a modified citric acid method were studied. Structure of the samples was characterized by X-ray studies with Rietveld method analysis. Magnetic properties and valence states of iron ions were characterized by ⁵⁷Fe Moessbauer spectroscopy performed at RT, which were found to be greatly dependent on the chemical composition of the samples. Electrical conductivity was measured in the 20–800 °C temperature range and for some compositions relatively high values (exceeding 100 S cm^− 1) were observed in the 600–800 °C range. Chemical stability studies in relation to Ce_0.8Gd_0.2O_1.9 electrolyte, performed for selected perovskite samples, revealed decreasing stability with increasing Ni concentration and formation of solid solutions in CGO/perovskite composites. The coefficient of thermal expansion (CTE) of LFN perovskites was found to match that of CGO electrolyte (CTE in the 10–13 · 10^− 6 K^− 1 range).     

Mixed oxygen ion and electron conducting hollow fiber membranes for oxygen separation

Phase inversion spinning technique was employed to prepare dense perovskite hollow fiber membranes made from composition BaCo_xFe_yZr_zO_3−δ (BCFZ, x + y + z = 1.0). Scanning electron microscope (SEM) shows that such hollow fibers have an asymmetric structure, which is favored to the oxygen permeation. An oxygen permeation flux of 7.6 cm³/min cm² at 900 °C under an oxygen gradient of 0.209 × 10⁵ Pa/0.065 × 10⁵ Pa was achieved. From the Wagner Theory, the oxygen permeation through the hollow fiber membrane is controlled by both bulk diffusion and surface exchange. The elements composition of fresh fiber and the fiber after long-term experiments were analyzed by energy-dispersive X-ray spectra (EDXS). Compared to the fresh fiber, sulphur was found on the tested hollow fiber membrane surface exposed to the air side and in the bulk, and Ba segregations occur on the tested hollow fiber membrane surface exposed to the air side. A decrease of the oxygen permeation flux was observed, which was probably due to the sulphur poisoning.     

La0.75Sr0.25Cr0.5Mn0.5O3−δ + Cu composite anode running on H2 and CH4 fuels

La_1−xSr_xCr_1−xM_xO_3−δ (M = Cr, Fe, V) system has been studied as anode materials for solid oxide fuel cells (SOFCs). The perovskite La_0.75Sr_0.25Cr_0.5Mn_0.5O_3−δ (LSCM) is stable in both H₂ and CH₄ atmospheres at temperatures up to 1000°C. However, in the reducing atmospheres of H₂ and CH₄, its electronic conductivity is greatly reduced from its value in air. We have characterized LSCM as the anode of a SOFC having 250 μm-thick La_0.8Sr_0.2Ga_0.83Mg_0.17O_2.815 (LSGM) as the electrolyte and SrCo_0.8Fe_0.2O_3−δ (SCF) as the cathode. We report a comparison of the overpotentials at the following anodes: (1) La_0.4Ce_0.6O_1.8 (LDC) + NiO composite in H₂, (2) porous LSCM in H₂ and CH₄, (3) porous LSCM impregnated with CuO in H₂ and CH₄ and (4) porous LSCM impregnated with CuO and sputtered with Pt in H₂ and CH₄. An LSCM + CuO + Pt anode gave a maximum power output at 850 °C of 850 mW/cm² and 520 mW/cm², respectively, with H₂ and CH₄ as fuel whereas anode (1) gave 1.4 W/cm² at 800 °C in H₂. There was no noticeable coke formation in CH₄ with anodes (2), (3) and (4), which demonstrates that the perovskite oxide is a plausible option for the anode of a SOFC operating with hydrocarbon fuels. We also report the moisture effect in the H₂ and CH₄ fuel-oxidation process.     

Oxygen non-stoichiometry and electrical conductivity of Pr2−xSrxNiO4±δ with x = 0–0.5

Oxygen non-stoichiometry and electrical conductivity of the Pr_2−xSr_xNiO_4±δ series with x = 0.0–0.5 were investigated in Ar/O₂ (pO₂ = 2.5 to 21 000 Pa) within a temperature range of 20–1000 °C. The equilibrium values of oxygen non-stoichiometry and electrical conductivity of these nickelates were determined as functions of temperature and oxygen partial pressure (pO₂). The nickelates with x = 0–0.5 appear to be p-type semiconductors in the investigated temperature and pO₂ ranges. The nickelates with x = 0.3–0.5 show very feebly marked pO₂ dependencies of the conductivity. Pr_1.7Sr_0.3NiO_4±δ shows the anomalies of the conductivity versus oxygen partial pressure which can be related to the orthorhombic–tetragonal crystal structure transformations. The conductivity of the Pr_2−xSr_xNiO_4±δ samples correlates with the average oxidation state of the nickel cations. The samples with x = 0.5 have the highest nickel oxidation state (≈ 2.5+), the highest [Ni³⁺]/[Ni²⁺] ratio close to 1 and show the highest conductivity (≈ 120 S/cm) in the whole pO₂ and temperature ranges investigated.     

Electrode reaction of Sr1−xLaxCo0.8Fe0.2O3−δ with x = 0.1 and 0.6 on Ce0.9Gd0.1O1.95 at 600 ≤ T ≤ 800 °C

The electrode reaction of the perovskite phases Sr_1−xLa_xCo_0.8Fe_0.2O_3−δ (x = 0.1 and 0.6) on Ce_0.9Gd_0.1O_1.95 has been investigated by impedance spectroscopy in the temperature range 600 ≤ T ≤ 800 °C. Thick porous electrodes (t ∼ 20 μm) were sprayed on Ce_0.9Gd_0.1O_1.95 and ac impedance spectra were recorded on symmetrical cells at the equilibrium. The analysis of the complex impedance diagrams clearly indicates the presence of two contributions. The low frequency one was assigned to the gas phase oxygen diffusion through the porous electrode and a finite length diffusion (Warburg) impedance was used to describe the high frequency (HF) data. The polarization resistance of the HF impedance contribution (R_w) is higher for x = 0.1 while the activation energy of R_w is higher for x = 0.6. The variations of R_w versus the La content, temperature and thickness indicate that the Warburg-type impedance contains information of both bulk oxygen diffusion and surface processes.     

An oxygen permeable membrane La0.8Sr0.2(Ga0.8Mg0.2)1 − xCrxO3 − δ for a reduced atmosphere

Mixed electron hole and oxide ion conducting perovskite-type oxides, La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ (0 ≤ x ≤ 1.0)_, were prepared by solid state reaction. The phase stability and the oxygen permeation properties of the oxides were examined as a function of the content of Cr. La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ has a perovskite related tetragonal phase with x = 0.1 to 0.8. The total electrical conductivity of La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ increases with increasing x. The oxygen permeation flux across the La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ membranes at higher temperatures increases with x up to x = 04. The maximum oxygen permeation flux of 1.6 × 10^? 7 mol^? 1 cm^? 2 at 1100 °C in a oxygen activity gradient of air/10^? 2 Pa is observed in La_0.8Sr_0.2(Ga_0.8Mg_0.2)_0.6Cr_0.4O_3 ? δ. This perovskite-type oxide is stable under an oxygen partial pressure of 7 × 10^? 10 Pa at 1000 °C.     

Defect interactions in La0.3Sr0.7Fe(M′)O3−δ (M′ = Al,Ga) perovskites: Atomistic simulations and analysis of p(O2)-T-δ diagrams

Atomistic modelling showed that a key factor affecting the p(O₂) dependencies of point defect chemical potentials in perovskite-type La_0.3Sr_0.7Fe_1−xM′_xO_3−δ (M′ = Ga, Al; x = 0–0.4) under oxidizing conditions, relates to the coulombic repulsion between oxygen vacancies and/or electron holes. The configurations of A- and B-site cations with stable oxidation states have no essential influence on energetics of the mobile charge carriers, whereas the electrons formed due to iron disproportionation are expected to form defect pair clusters with oxygen vacancies. These results were used to develop thermodynamic models, adequately describing the p(O₂)-T-δ diagrams of La_0.3Sr_0.7Fe(M′)O_3−δ determined by the coulometric titration technique at 923–1223 K in the oxygen partial pressure range from 1 × 10^− 5 to 0.5 atm. The thermodynamic functions governing the oxygen intercalation process were found independent of the defect concentration. Doping with aluminum and gallium leads to increasing oxygen deficiency and induces substantial changes in the behavior of iron cations, increasing the tendencies to disproportionation and hole localization. Despite similar oxygen nonstoichiometry in the Al- and Ga-substituted ferrites at a given dopant content, the latter tendency is more pronounced in the case of aluminum-containing perovskites.