Electrical conductivity and oxygen permeation properties of SrCoFeOx membranes

The total conductivity and oxygen permeation properties of dense SrCoFeO_x membranes synthesized from the solid state method were studied in the temperature range of 700–900 °C. The SrCoFeO_x membranes consist of an intergrowth (Sr₄Fe_6 − xCo_xO_13 ± δ), perovskite (SrFe_1 − xCo_xO_3 − δ), and spinel (Co_3 − xFe_xO₄) phase. SrCoFeO_x exhibits n-type and p-type conduction at low and high oxygen partial pressures, respectively, and has a total conductivity of 16.5 S/cm at 900 °C in air. The oxygen permeation fluxes for SrCoFeO_x and SrFeCo_0.5O_x membranes were measured with either an inert or carbon monoxide sweep gas. The oxygen permeation fluxes were higher through SrCoFeO_x membranes than SrFeCo_0.5O_x membranes and can be attributed to a difference in the amount and makeup of the perovskite phase present in each composition. The oxygen permeation fluxes with a carbon monoxide sweep gas were approximately two orders of magnitude larger than the fluxes measured with an inert sweep gas for both compositions. The large oxygen permeation fluxes observed with a carbon monoxide sweep are due to a higher driving force for oxygen transport and a reaction on the sweep side of the membrane that maintains a low oxygen partial pressure.     

Spectroscopic properties of Co2+: ZnAl2O4 nanocrystals in sol–gel derived glass–ceramics

Transparent glass–ceramics containing zinc–aluminum spinel (ZnAl₂O₄) nanocrystals doped with tetrahedrally coordinated Co²⁺ ions were obtained by the sol–gel method for the first time. The gels of composition SiO₂–Al₂O₃–ZnO–CoO were prepared at room temperature and heat-treated at temperature ranging 800–950 °C. When the gel samples were heated up to 900 °C, ZnAl₂O₄ nanocrystals were precipitated. Co²⁺ ions were located in tetrahedral sites in ZnAl₂O₄ nanocrystals. X-ray diffraction analysis shows that the crystallite sizes of ZnAl₂O₄ crystal become large with the heat-treatment temperature and time, and the crystallite diameter is in the range of 10–15 nm. The dependence of the absorption and emission spectra of the samples on heat-treatment temperature were presented. The difference in the luminescence between Co²⁺ doped glass–ceramic and Co²⁺ doped bulk crystal was analysed. The crystal field parameter D_q of 423 cm⁻¹ and the Racah parameters B of 773 cm⁻¹ and C of 3478.5 cm⁻¹ were calculated for tetrahedral Co²⁺ ions.     

Ceramic oxides with high oxygen exchange: The system Sr–Co–O

Oxide compositions in the system Sr–Co–O were prepared by solid-state reaction. The oxide–oxygen reactions were investigated by thermo-gravimetric measurements. Equilibration was controlled by an amperometric lambda sensor. Thermodynamic data for the oxide–oxygen reaction were calculated. For the reaction CoO/Co₃O₄ with complete change of crystal structure between ferrite-and NaCl-types, the amount of oxygen exchanged (δ = 1), and the absolute values of changes in enthalpy and entropy are the highest. The lowest values were observed for the partial molar enthalpy of the solid-solution reaction of oxygen with the stable perovskite phase of Sr_0.965Ce_0.035CoO_2.535+n.     

Oxygen adsorption properties of YBaCo4O7-type compounds

The oxygen adsorption and desorption of newly found compounds RBaCo₄O₇ (R = Y, Dy–Lu, In) were investigated by thermogravimetry (TG) in the temperature range from room temperature to 1100 °C. The influence of Co replaced by Zn and Fe on the oxygen diffusion properties of YBaCo₄O₇ was also studied. TG results showed clearly that all RBaCo₄O₇ compounds basically experience two oxygen adsorption and desorption processes in the temperature range 20∼1100 °C in oxygen flow. One happens at about 200∼450 °C and the another happens at about 660∼1050 °C. The differences between the resulting states by adsorbing oxygen at lower and high temperature were discussed based on the X-ray diffraction (XRD) patterns and TG data. We showed evidence that the oxygen adsorption at the lower temperature has a small activation energy, while the oxygen adsorption at the higher temperature has a large activation energy. The oxygen adsorbed at high temperature will destroy the RBaCo₄O₇ structure. Zn substituting in the YBaCo_4 − xZn_xO₇ influences the oxygen diffusion behavior prominently, the amount of oxygen adsorbed becomes increasingly weak with the increase of Zn content and disappears completely for the samples with x ≥ 2.0. However, replacement of Co by Fe has little effect on the oxygen absorption process.     

A-deficit LSCF for intermediate temperature solid oxide fuel cells

A-deficit La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ cathode material for intermediate temperature solid oxide fuel cells (IT-SOFCs) was synthesized by a citrate complexation (Pechini) route. Using La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ as cathode material, a superior cell performance with the maximum power density of 309, 470 and 855 mW cm^? 2 at 600, 650 and 700 °C was achieved, in contrast with the maximum power density of 266, 354 and 589 mW cm^? 2 using conventional La_0.6Sr_0.4Co_0.2Fe_0.8O_3 ? δ as cathode material at the same temperatures. The reason of this improvement was analyzed on the basis of defect chemistry. Thermal shrinkage experiment testified that the oxygen vacancies in La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ are more mobile than in La_0.6Sr_0.4Co_0.2Fe_0.8O_3 ? δ. Furthermore, theoretical calculation in terms of their composition and the shift of peak position in XRD pattern showed that the concentration of oxygen vacancies of La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ is higher than that of La_0.6Sr_0.4Co_0.2Fe_0.8O_3 ? δ. Therefore, the oxygen ion conductivity via vacancies transfer mechanism is enhanced, which induces the polarization resistance of La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ being decreased with a result of cell performance improved.     

Cobalt oxide nanolayers on Pd(100): The thickness-dependent structural evolution

The growth of interface-stabilized cobalt oxide (CoO_x) nanolayers on Pd(100) has been investigated and their structures are reported as a function of coverage. Several different phases have been observed by LEED and STM experiments, and they have been characterized spectroscopically by photoemission and X-ray absorption. The data indicate that in the low coverage regime (up to Θ_Co ≈ 2–3 ML) rock-salt CoO type phases are formed (defective in the single layer regime, and stoichiometric in multilayers) with (100) or (111) termination. At higher coverage (Θ_Co ≈ 10–20 ML) spinel Co₃O₄(111) and CoO(100) layers have been detected, in ratios dependent on the preparation conditions. The observed structures are discussed in relation to similar structures reported recently for CoO_x films on Ir(100) [W. Meyer et al., J. Phys.: Condens. Matter 20 (2008) 265011].     

Oxygen nonstoichiometry,mixed valency and mixed conduction in (La,Sr)(Co,Fe)O3−δ

Defect chemistry for a mixed conductor, La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ was studied. Samples were treated under controlled oxygen partial pressure, P(O₂), conditions at 1273 K [10^− 11.1 ≤ P(O₂)/atm ≤ 1], and cooled to room temperature. Oxygen nonstoichiometry and valences of transition metal ions for the treated samples were evaluated by iodometry and X-ray absorption spectroscopy, respectively. With decreasing P(O₂), preferential reduction of Co³⁺ to Co²⁺ was observed, while iron preserved its higher valence above 3 under conditions studied. A dependency of its electrical conductivity on P(O₂) was discussed along with a change in concentration of oxygen vacancies and mixed valences.     

Theoretical investigation of the inversion parameter in Co3 − sAlsO4 (s = 0–3) spinel structures

The structural, energetic, and thermodynamic properties of the Co_3 ? sAl_sO₄ (s = 0, 1, 2, and 3) crystal family are studied using periodic DFT calculations. We provide a quantitative discussion of the cation distribution effect on the cell parameter, the oxygen Wyckoff position, the interatomic distances and the energies of the structures. It is demonstrated that the low cobalt containing CoAl₂O₄ spinel is the most stable structure of the Co_3 ? sAl_sO₄ (s = 0, 1, 2, and 3) crystal family.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Sonochemical synthesis and characterization of Co3O4 nanocrystals in the presence of the ionic liquid [EMIM][BF4]

For the first time, a sonochemical process has been used to synthesis cobalt oxide Co₃O₄ nanoflowers and nanorods morphology in the presence of the ionic liquid 1-Ethyl-3-methylimidazolium tetrafluoroborate [EMIM][BF₄] as reaction media and morphology template. Different sonication time periods and different molar ratios of the ionic liquid (IL) were used to investigate their effects on the structural, optical, chemical and magnetic properties of the produced Co₃O₄ nanoparticles. During synthesis process brown powder contains cobalt hydroxide Co(OH)₂ and cobalt oxyhydroxide (Cobalt hydroxide oxide) CoO(OH) was formed, after calcination in air for 4 h at 400 °C a black powder of Co₃O₄ nanoparticles was produced. The produced Co₃O₄ nanoparticles properties were characterized by X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FE-SEM), transmission electron microscopy (TEM), FTIR spectroscopy, UV–vis spectroscopy, and Vibrating Sample Magnetometer (VSM). To explain the formation mechanism of Co₃O₄ NPs some investigations were carried on the brown powder before calcination.     

Modification of B-site doping of perovskite LaxSr1 − xFe1 − y−zCoyCrzO3 − δ oxide by Mg2+ ion

Co-doping B-site of perovskite oxide La_xSr_1 ? xCo_yFe_1 ? yO_3 ? δ (LSCFO) with Cr⁶⁺ and Mg²⁺ ions has been attempted in this research for revamping chemical stability and oxygen ionic conductivity of this mixed conducting oxide. It is known that partial substitution for B-site cations of LSCFO by Cr gives rise to a significant improvement on chemical and thermal stability of the perovskite oxide. On the basis of this doped structure, introduction of an immaterial dose of Mg²⁺ ion into its B-site results in a microstructure consisting of smaller grains with higher density than its precursor. Furthermore, the resulting perovskite oxide La_0.19Sr_0.8Fe_0.69Co_0.1Cr_0.2 Mg_0.01O_3 ? δ (LSFCCMO) displays higher O^2? conductivity than the solely Cr-doped LSCFO besides the improved chemical stability against reduction in 5% CH₄/He stream at 850 °C. A detailed examination of the oxidation states of B-site transition metal ions by XPS has also been conducted as a part of structural characterizations of LSFCCMO. The assessment of relative O^2? conductivity shows that the grain boundary area plays a more important role than the bulk phase in facilitating ion transport, but with comparable boundary areas the higher densification level is favorable.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

Oxygen nonstoichiometry and defect structure of the double perovskite GdBaCo2O6 − δ

The results of oxygen nonstoichiometry, δ, measured by means of coulometric technique as a function of oxygen partial pressure, p_O2, in temperature range 900 ≤ T °C ≤ 1050 are presented for GdBaCo₂O_6 − δ with double perovskite structure. Partial molar enthalpy and entropy of oxygen in GdBaCo₂O_6 − δ structure were calculated. Both thermodynamic properties were shown to increase dramatically in the vicinity of the oxygen nonstoichiometry value equal to 1. The p_O2 dependences of oxygen nonstoichiometry and the δ dependences of the partial molar properties were found to have inflections when the oxygen content of GdBaCo₂O_6 − δ is equal to 5.0 exactly. The modeling of the defect structure of the double perovskite GdBaCo₂O_6 − δ was carried out by considering different reference states. Only the model based on the cubic perovskite GdCoO₃ as a reference state was shown to fit the experimental data on oxygen nonstoichiometry of GdBaCo₂O_6 − δ good enough. Equilibrium constants of the appropriate defects reactions were, therefore, determined. Concentrations of all defect species defined within the framework of this model were calculated as functions of temperature and oxygen nonstoichiometry. Oxygen vacancies were shown to be formed during p_O2 diminution in gas environment in the layers of GdBaCo₂O_6 − δ crystal lattice where they are ordered until oxygen nonstoichiometry of the oxide becomes equal to unity afterwards oxygen vacancies are formed randomly in oxygen polyhedrons.     

Electric property of mixed conductor BaIn1−xCoxO3−δ

We synthesized BaIn_1−xCo_xO_3−δ (x = 0–0.8) with a defective perovskite structure by partly replacing In with Co in Ba₂In₂O₅. Based on XRD measurements, the synthesized compound was found to have cubic perovskite and orthorhombic brownmillerite structures depending on the amount of Co. BaIn_1−xCo_xO_3−δ (x = 0.2 and 0.3) showed high total electrical conductivities without undergoing the structural transformation that the original Ba₂In₂O₅ undergoes. Some of the samples showed both electronic and oxide ionic conductivities. At the same time, the oxide ionic conductivity was comparable with that of Ba₂In₂O₅. For example, the sample with x = 0.1 had a total electrical conductivity of 4.7 × 10^− 1 S cm^− 1 and an oxide ion transport number of 0.52 at 850 °C.     

Enhancement of oxygen surface kinetics of SrTiO3 by alkaline earth metal oxides

The kinetics of oxygen incorporation into semiconducting metal oxides such as strontium titanate are of particular interest for an application as a fast resistive-type oxygen sensor operating at high temperatures (T > 600 °C), e.g. in automotive exhaust gas monitoring.Based on a frequency-domain analysis of the response signal (resistance R) obtained from an electrically contacted sample exposed to a modulated oxygen partial pressure pO₂ in a fast kinetic measurement setup, the surface transfer controlled response behaviour of undoped and Fe-doped SrTiO₃ single crystals with thicknesses in the order of d = 45–125 μm was investigated with regard to the effect of thin PVD layers with alkaline earth (Ca, Sr, Ba) metal oxide compounds.The results of this electrical characterisation are compared with results obtained from ¹⁸O tracer exchange experiments and subsequent depth profile analysis by secondary ion mass spectrometry (SIMS). Both the electrical measurements and the ¹⁸O self-diffusion experiments revealed an enhancement of oxygen surface exchange kinetics in the case of all three alkaline earth metal oxides investigated.     

Oxygen permeation characteristics of zirconia with surface modification

Yttria-stabilized zirconia (YSZ) can be used as an oxygen-permeating membrane at elevated temperature (> 1400 °C) due to its chemical and mechanical stability. It was previously shown that the oxygen transport through YSZ membrane in reducing oxygen partial pressure (P_O2) was highly influenced by the surface-exchange kinetics that can be improved by porous surface coating layers such as YSZ, GDC (Gd-doped ceria) or YSZ–GDC mixture [H.J. Park, G.M. Choi, J. Eur. Ceram. Soc. 25 (2005) 2577]. However, the increased oxygen flux was still lower than that estimated assuming bulk-diffusion limit and rapidly decreased with time due to the sintering of coating layers and the reaction between bulk YSZ and coating layers. In this study, the oxygen fluxes through YSZ with LaCrO₃, GDC + LaCrO₃ (bilayer), LaCrO₃ + 5 wt.% GDC (mixture), or LaCr_0.7Co_0.3O₃ coatings were measured under controlled P_O2 gradient (permeate-side P_O2: ∼ 3 × 10^− 12 atm, feed-side P_O2: 2 × 10^− 10–2 × 10^− 8 atm) at 1600 °C. The oxygen flux drastically increased with these coatings. The highest increase in oxygen flux was shown with GDC + LaCrO₃ (bilayer) coating and was maintained for a long time. The presence of highly catalytic Ce ions while maintaining porous structure in the coating layer may explain the observation. The prevention of formation of resistive layer due to ceria coating may also be partly responsible for the observation.     

Rate limiting steps of the porous La0.6Sr0.4Co0.8Fe0.2O3−δ electrode material

The electrode reaction of porous La_0.6Sr_0.4Co_0.8Fe_0.2O_3?δ films deposited onto Ce_0.9Gd_0.1O_1.95 (CGO) was investigated by impedance spectroscopy within the temperature and oxygen partial pressure (pO₂) ranges of 500 ≤ T ≤ 700 °C and 10^? 4 < pO₂ < 1 atm, respectively, using Ar and He as gas carriers. The electrochemical impedance spectroscopy (EIS) measurements reveal a high frequency (HF) and a low frequency (LF) regions in the Nyquist plane. The high frequency (HF) region was fitted with a Warburg-type impedance element, and the low frequency (LF) region was reproduced with a resistance in parallel to a constant phase element. Both, the slight dependence of the polarization resistance (R_W) and the small variation of the apex frequency (f_v) of the HF Warburg-type element, on pO₂, suggest that this contribution corresponds to the oxygen diffusion in the bulk of the La_0.6Sr_0.4Co_0.8Fe_0.2O_3?δ electrode material. The variation of the polarization resistance of the LF region (R_rcpe) with pO₂ indicates that as T increases, the limiting step evolves from dissociative oxygen adsorption to oxygen gas diffusion in the pores of the mixed ionic/electronic conductor (MIEC) electrode.     

Mixed conductivity and oxygen permeability of doped Pr2NiO4-based oxide

Pr₂NiO₄-based oxide was studied as a new mixed electronic and oxide ionic conductor for the oxygen permeation membrane. It was found that Pr₂NiO₄ doped with Cu and Fe for Ni site exhibits the relatively high oxygen permeation rate. Doping second cation to Ni site is effective for improving the oxygen permeation rate and the trivalent cation seems to be effective for increasing the oxygen permeation rate. Among the examined cation, the highest oxygen permeation rate was obtained by doping 5 mol% Fe. The oxygen permeation rate was also significantly affected by the surface catalyst and the highest oxygen permeation rate of 80 μmol·min^− 1·cm^− 2 at 1273 K was achieved by using La_0.1Sr_0.9Co_0.9Fe_0.1O₃ for the surface catalyst. Since the electrical conductivity slightly decreased with decreasing P_O2 and it dropped significantly at P_O2 = 10^− 19 atm, chemical stability of Pr₂NiO₄-based oxide seems to be reasonably high. Application of this new mixed conductor for the oxygen permeation membrane under the CH₄ partial oxidation was also studied and it was confirmed that the oxygen permeation rate much improved under the CH₄ oxidation condition and this Pr₂NiO₄ can be used for the oxygen permeation membrane for the CH₄ partial oxidation.     

Structure and electrochemical properties of Sm0.5Sr0.5Co1 − xFexO3 − δ cathodes for solid oxide fuel cells

Crystal structure, thermal expansion coefficient, electrical conductivity and cathodic polarization of compositions in the system Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ with 0 ≤ x ≤ 0.9 were studied as function of Co / Fe ratio and temperature, in air. Two phases, including an Orthorhombic symmetry for 0 ≤ x ≤ 0.4 and a cubic symmetry for 0.5 ≤ x ≤ 0.9, were observed in samples of Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ at room temperature. The adjustment of thermal expansion coefficient (TEC) to electrolyte, which is one of the main problems of SSC, could be achieved to lower TEC values with more Fe substitution. High electrical conductivity above 100 S/cm at 800 °C was obtained for all specimens, so they could be good conductors as cathodes of IT-SOFC. The polarization behavior of SSCF as a function of Fe content was evaluated by means of AC impedance using LSGM electrolyte. It was discovered that the Area Specific Resistance (ASR) of SSCF increased as the amount of substitution of Fe for Co increased. When the amount of Fe reached to 0.4, the highest ASR was obtained and then the resistance started decreasing above that. The electrode with a composition of Sm_0.5Sr_0.5Co_0.2Fe_0.8O_3 − δ showed high catalytic activity for oxygen reduction operating at temperature ranging from 700 to 800 °C.     

TPD and ITPD study of materials used as chemoresistive gas sensors

Temperature-programmed desorption (TPD) and a differential form of it, called intermittent temperature-programmed desorption (ITPD), turned out to be powerful characterising techniques for chemoresistive materials applied to gas sensing. We investigated samples of SnO₂, TiO₂ and solid solutions of them (Ti_xSn_1 ? xO₂). TPD and ITPD experiments were carried out in vacuum, with samples previously treated in pure O₂ (100 Torr, 500 °C, 30 min). Amounts of desorbed O₂ corresponded for all Ti-containing samples to less than 10% of a compact monolayer of ions O^2?. Corresponding values of the apparent activation energy of desorption (E_app) were calculated directly from the Arrhenius plots for each partial TPD and ranged from about 100 to 330 kJ mol^? 1 (1.16 to 3.82 eV).