The improvement in dielectric and ferroelectric performance of PZT–PZN ceramics by thermal treatment

Pyrochlore-free lead zirconate titanate – lead zinc niobate ceramics have been systematically investigated in the as-sintered condition as well as after annealing. The ceramics were characterized by dielectric spectroscopy and Sawyer–Tower polarization (P–E) measurements. The powders of Pb[(Zr_1/2Ti_1/2)_(1−x)–(Zn_1/3Nb_2/3)_x]O₃, where x = 0.1, 0.3 and 0.5 were prepared using the columbite–(wolframite) precursor method. The general trend seems to indicate that the annealed samples become more normal-ferroelectric-like behavior as opposed to the relaxor-ferroelectric-like behavior observed in the as-sintered state. The as-sintered 0.9PZT–0.1PZN ceramic exhibited weak relaxor-ferroelectric behavior, with a relatively low dielectric constant maximum of 14,000 measured at 1 kHz. Annealing resulted in a transition to normal-ferroelectric-like behavior, a shift in the dielectric maximum temperature from 360 °C to 350 °C, and a dramatic increase in the dielectric constant at 1 kHz to a maximum value of 35,000 for the longer anneal. After thermal annealing at 900 °C for one week a strong enhancement of remanent polarization (P_r) was observed.     

An efficient approach for the direct synthesis of lithium niobate powders

Lithium niobate powders from the raw powders of Li₂CO₃ and Nb₂O₅ are directly synthesized by a combustion method with urea as fuel. The synthesis parameters (e. g., the calcination temperature, calcination time, and urea-to-(Li₂CO₃ + Nb₂O₅) quantity ratio) are studied to reveal the optimized synthesis conditions for preparing high-quality lithium niobate powders. In our present work, it is found that a urea-to-(Li₂CO₃ + Nb₂O₅) ratio close to 3, calcination temperature at 550∼600 °C and reaction time around 2.5 h may lead to high-quality lithium niobate powders. The microstructure of synthesized powders is further studied; a possible mechanism of the involved reactions is also proposed.     

Effect of processing conditions on sonochemical synthesis of nanosized copper aluminate powders

Nanosized copper aluminate (CuAl₂O₄) spinel particles have been prepared by a precursor approach with the aid of ultrasound radiation. Mono-phasic copper aluminate with a crystallite diameter of 17 nm along the (3 1 1) plane was formed when the products were synthesized using Cu(NO₃)₂·6H₂O and Al(NO₃)₃·9H₂O as starting materials, with urea as a precipitation agent at a concentration of 9 M. The reaction was carried out under ultrasound irradiation at 80 °C for 4 h and a calcination temperature of 900 °C for 6 h. The synthesized copper aluminate particles and the effect of different processing conditions such as the copper source, precipitation agents, sonochemical reaction time, calcination temperature and time were analyzed and characterized by the techniques of powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM) and Fourier transformation infrared spectroscopy (FT–IR).     

Influence of fabrication processing on phase transition and electrical properties of 0.8Pb(Zr1/2Ti1/2)O3–0.2Pb(Ni1/3Nb2/3)O3 ceramics

The binary system of 0.8Pb(Zr_1/2Ti_1/2)O₃–0.2Pb(Ni_1/3Nb_2/3)O₃ ceramics were synthesized by conventional mixed oxide and columbite method. X-ray diffraction analysis demonstrated the coexistence of both the rhombohedral and tetragonal phases for the columbite prepared sample. Rhombohedral to tetragonal phase transition for columbite method was different compared with those of the mixed oxide method. The permittivity shows a shoulder at the rhombohedral to tetragonal phase transition temperature T_Rho–Tetra = 195 °C, and then a maximum permittivity (36,000 at 10 kHz) at the transition temperature T_m = 277 °C on ceramics prepared with the columbite method. However, piezoelectric coefficient (d₃₃) was measured to be 282 pC/N for the conventional method and higher than the columbite method. The results were related to the phase compositions and porosity of the ceramics.     

Rare-earth doped (Lu0.85Y0.15)2SiO5 nanocrystalline powders obtained by polymer assisted sol–gel synthesis

In the present work we explored the possibility of obtaining nanocrystalline (Lu_0.85Y_0.15)₂SiO₅ (LYSO) powders using polymer assisted sol–gel method. The synthesis started from TEOS as alkoxide precursor while polyethylene glycol with average molecular weight of 4000 was used as fuel. The resulting powders were obtained by firing gels in two ways: in conventional furnace and in microwave oven, with further annealing. This modified sol–gel synthetic route enabled production of pure phase LYSO powders at much lower temperatures (1050 °C) compared to classical, -solid-state methods (1400 °C). Crystallization kinetics are examined using differential thermal analysis, and rather low values of crystallization activation energies (around 12 kJ/mol) were found, revealing good potential of this method for low-temperature production of LYSO powder.     

A simple MOD method to grow a single buffer layer of Ce0.8Gd0.2O1.9 (CGO) for coated conductors

A single Ce_0.8Gd_0.2O_1.9 (CGO) buffer layer was successfully grown on the home-made textured Ni–5 at.%W (Ni–5W) substrates for YBCO coated conductors by a simple metal–organic deposition (MOD) technique. The precursor solution was prepared using a newly developed process and only contained common metal–organic salts of both Ce and Gd dissolved into a propionic acid solvent. The precursor solution at 0.4 M concentration was spin coated on short samples of Ni–5W substrates and heat-treated at 1100 °C in a mixture gas of 5% H₂ in Ar for an hour. X-ray studies indicated that the CGO films had good out-of-plane and in-plane textures with full-width-half-maximum values of 4.18° and 6.19°, respectively. Atomic force microscope (AFM) investigations of the CGO films revealed that most of the grain boundary grooves on the Ni–5W surface were found to be well covered by CGO layers, which had a fairly dense and smooth microstructure without cracks and porosity. These results indicate that our MOD technique is very promising for further development of single buffer layer architecture for YBCO coated conductors, due to its low cost and simple process.     

Ce0.8Sm0.2O1.9 synthesis for solid oxide fuel cell electrolyte by ultrasound assisted co-precipitation method

In this study, the synthesis of Ce_0.8Sm_0.2O_1.9 (SDC) solid electrolyte by the ultrasound assisted co-precipitation method was accomplished to explore the effects of ultrasound power, ultrasound pulse ratio and probe type upon the ionic conductivity of SDC as well as the lattice parameter, the microstructure and the density. Fine powders of uniform crystallite sizes (average 11.70 ± 0.62 nm) were obtained, needing lower sintering temperature. The SDC powders were successfully sintered to a relative density of over 95% at 1200 °C (5 °C min^?1) for 6 h. The micrograph of SDC pellets showed non-agglomerated and well-developed grains with average size of about 200 nm. X-ray diffraction analysis showed that the lattice parameter increased with increasing acoustic intensity and reached a maximum for the 14.94 W cm^?2. Further, a linear relationship was detected between the lattice parameter and the ionic conductivity, inspiring a dopant like effect of US on the electrolyte properties. The highest ionic conductivity as σ_800°C = 3.07 × 10^?2 S cm^?1 with an activation energy E_a = 0.871 kJ mol^?1 was obtained with pulsed ultrasound for an acoustic intensity of 14.94 W cm^?2, using 19 mm probe and 8:2 pulse ratio.     

Temperature dependent structural and optical properties of tin oxide nanoparticles

Nanocrystalline tin oxide (SnO₂) powders were synthesized through wet chemical route using tin metal as precursor. The morphology and optical properties, as well as the effect of sintering on the structural attributes of SnO₂ particles were analyzed using Transmission electron microscopy (TEM), UV–visible spectrophotometry (UV–vis) and X-ray diffraction (XRD), respectively. The data revealed that the lattice strain plays a significant role in determining the structural properties of sintered nanoparticles. The particle size was found to be 5.8 nm, 19.1 nm and 21.7 nm for samples sintered at 300 °C, 500 °C, and 700 °C, respectively. Also, the band gaps were substantially reduced from 4.1 eV to 3.8 eV with increasing sintering temperatures. The results elucidated that the structural and optical properties of the SnO₂ nanoparticles can be easily modulated by altering sintering temperature during de novo synthesis.     

Synthesis and characterization of nanocrystalline HAp powders prepared by using aloe vera plant extracted solution

Nanocrystalline hydroxyapatite (HAp) powders were synthesized by a simple method using aloe vera plant extracted solution. To obtain nanocrystalline HAp, the prepared precursor was calcined in air at 400–800 °C for 2 h. The phase composition of the calcined samples was studied by X-ray diffraction (XRD) technique. The XRD results confirmed the formation of HAp phase. With increasing calcination temperature, the crystallite of the HAp increased, showing the hexagonal structure of HAp with the lattice parameter, a, in a range of 0.9520–0.9536 nm and c of 0.6739–0.6928 nm. The particle sizes of the powder were obtained to be 43–171 nm. The optical properties of the calcined powders were characterized by Raman and FTIR spectroscopies. The Raman spectra showed a main peak of the phosphate vibration mode (ν₁(PO₄)) at ∼963 cm⁻¹ for all the calcined samples. The peaks of the phosphate carbonate and hydroxyl vibration modes were observed in the FTIR spectra for all the calcined powders. The morphology tends to change from a spherical shape to a rod-like shape with increasing calcination temperature as revealed by TEM.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

High lithium ion conductivity glass-ceramics in Li2O–Al2O3–TiO2–P2O5 from nanoscaled glassy powders by mechanical milling

Mechanical milling (MM) has been used to prepare the nanosized Li_1.4Al_0.4Ti_1.6(PO₄)₃ (denoted LATP) glassy powders, which was converted into glass-ceramics through thermal treating at 700–1000 °C. The XRD, TEM, FESEM and ac impedance techniques were used to characterize the products. The results showed that completely amorphous products were prepared by MM for 40 h, and single-phase LiTi₂(PO₄)₃-type structured glass-ceramics were obtained by further heat treatment. The lithium ion conductivity of the glass-ceramics increased with the growth of the crystalline phase and decrease of the grain size. The highest bulk conductivity (σ_b) of 1.09 × 10^− 3 S cm^− 1 with an energy of activation as low as 0.28 eV was obtained at room temperature for the specimen treated at 900 °C for 6 h. The high conductivity, easy fabrication and low cost make the LATP glass-ceramics promising to be used as inorganic solid electrolyte for all-solid-state Li-ion rechargeable batteries.     

Ultrasound-induced emulsification of subcritical carbon dioxide/water with and without surfactant as a strategy for enhanced mass transport

Pulsed ultrasound was used to disperse a biphasic mixture of CO₂/H₂O in a 1 dm³ high-pressure reactor at 30 °C/80 bar. A view cell positioned in-line with the sonic vessel allowed observation of a turbid emulsion which lasted approximately 30 min after ceasing sonication. Within the ultrasound reactor, simultaneous CO₂-continuous and H₂O-continuous environments were identified. The hydrolysis of benzoyl chloride was employed to show that at similar power intensities, comparable initial rates (1.6 ± 0.3 × 10^–3 s^–1 at 95 W cm^–2) were obtained with those reported for a 87 cm³ reactor (1.8 ± 0.2 × 10^–3 s^–1 at 105 W cm^–2), demonstrating the conservation of the physical effects of ultrasound in high-pressure systems (emulsification induced by the action of acoustic forces near an interface). A comparison of benzoyl chloride hydrolysis rates and benzaldehyde mass transport relative to the non-sonicated, ‘silent’ cases confirmed that the application of ultrasound achieved reaction rates which were over 200 times faster, by reducing the mass transport resistance between CO₂ and H₂O. The versatility of the system was further demonstrated by ultrasound-induced hydrolysis in the presence of the polysorbate surfactant, Tween, which formed a more uniform CO₂/H₂O emulsion that significantly increased benzoyl chloride hydrolysis rates. Finally, pulse rate was employed as a means of slowing down the rate of hydrolysis, further illustrating how ultrasound can be used as a valuable tool for controlling reactions in CO₂/H₂O solvent mixtures.     

Electrical conductivity of fully densified nano CaZr0.90In0.10O3 − δ ceramics prepared by a water-based gel precipitation method

Water-based gel precipitation method was first applied to synthesize high purity nano CaZr_0.90In_0.10O_3 ? δ powders suitable for fabricating dense ceramics at lower temperature. By using CaCO₃, Zr(NO₃)₄ and In(NO₃)₃ as raw materials, PEG as dispersant, CaZr_0.90In_0.10O_3 ? δ with an average particle size of about 40 nm was obtained at 850 °C, which was nearly 350 °C lower than that of traditional solid-state reaction method. Fully densified ceramics with an average grain size of 200–300 nm were obtained at 1350 °C, a temperature about 250 °C lower than that of traditional sintering techniques. Experimental results showed that the flexure stress, total, bulk and grain boundary protonic conductivities of the ceramics were more favorable than those of the ceramics fabricated at 1500 °C and 1600 °C from the powders synthesized by solid-state reaction method.     

Evaluation of ionic conductivity for Mg–Al layered double hydroxide intercalated with inorganic anions

This study demonstrates that humidity, temperature, and the interlayer anions influence ionic conductivities of Mg–Al layered double hydroxides (LDHs) intercalated with inorganic anions. Results show that Mg–Al LDH intercalated with Br^? exhibited the highest ionic conductivity among Mg–Al LDHs intercalated with CO₃^2?, Cl^?, Br^?, NO₃^? and SO₄^2?. Its ionic conductivity was 1.1 × 10^? 2 S cm^? 1 at 80 °C under 80% relative humidity. The electromotive force for the hydroxide ion concentration cell using Mg?Al CO₃^2? LDH showed the same behavior with that using an anion exchange membrane, indicating that Mg–Al CO₃^2? LDH can be a hydroxide ion conductor.     

Development and characterization of a quasi-ternary diagram based on La0.8Sr0.2(Co,Cu,Fe)O3 oxides in view of application as a cathode contact material for solid oxide fuel cells

Oxides resulting from discrete changes in composition within the quasi-ternary system La_0.8Sr_0.2CuO_2.4 + δ–La_0.8Sr_0.2CoO_3 ? δ–La_0.8Sr_0.2FeO_3 ? δ were investigated under similar experimental conditions with the objective of obtaining an overview of the variation of the relevant properties for possible applications as cathode contact layer in SOFCs. Twenty-two oxide compositions within this system were systematically selected and synthesized under identical conditions by the Pechini method. The distribution of the different crystallographic phases at 1050 °C within this quasi-ternary phase diagram, the DC electrical conductivity at 800 °C and the thermal expansion coefficients are presented. Perovskites of different compositions issued from this ternary diagram were tested as cathode contact material between an La_0.8Sr_0.2FeO₃ cathode and a Crofer22APU interconnect by resistance measurements at 800 °C. The application of a MnCo_1.9Fe_0.1O₄ spinel protection reduced the interfacial reaction between the Crofer22APU and the cathode contact material. Electrical resistance measurements at 800 °C in air up to 1000 h and the analysis by scanning electron microscopy/energy-dispersive X-ray spectroscopy of the sample cross-sections were carried out to verify the surface stability and the electrical performance.     

Electrochemical properties of spinel-type manganese oxide/porous carbon nanocomposite powders in 1 M KOH aqueous solution

Spinel-type manganese oxide/porous carbon (Mn₃O₄/C) nanocomposite powders have been simply prepared by a thermal decomposition of manganese gluconate dihydrate under an Ar gas flow at above 600 °C. The structure and texture of the Mn₃O₄/C nanocomposite powders are investigated by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS) equipped scanning transmission electron microscopy (STEM), transmission electron microscopy (TEM), selected area-electron diffraction (SA-ED), thermogravimetric and differential thermal analysis (TG-DTA) and adsorption/desorption of N₂ gas at ?196 °C. The electrochemical properties of the nanocomposite powders in 1 M KOH aqueous solution are studied, focusing on the relationship between their structures and electrochemical capacitance.In the nanocomposite powders, Mn₃O₄ nano particles approximately 5 nm in size are dispersed in a porous carbon matrix. The nanocomposite powders prepared at 800 °C exhibit a high specific capacitance calculated from cyclic voltammogram of 350 and 600 F g^?1 at a sweep rate of 1 and 0.1 mV s^?1, respectively. The influence of the heating temperature on the structure and the electrochemical properties of nanocomposite powders is also discussed.     

Phase evolution and morphology of nanocrystalline BaCe0.9Er0.1O3−δ proton conducting oxide synthesised by a novel modified solution combustion route

Pure BaCeO₃ and 10 mol% Er₂O₃ doped BaCeO₃ (BCE) was synthesised by a novel modified solution combustion synthesis (MCS) route wherein the pH of the precursor solution was varied and the phase formation and morphology were compared with those obtained in conventional solution combustion synthesis (SCS). X-ray diffraction (XRD) studies confirmed the presence of the undesirable BaCO₃ phase in the calcined powders prepared using SCS route whereas the powders synthesised with the modified (MCS) route exhibited a single perovskite phase after calcination. Variation in the pH of the precursor solution resulted in a morphology change from a mix of irregular and globular at pH 4 to more spherical at pH 6 and 8. Fourier transform infrared spectroscopy (FT-IR) studies revealed that calcination time has more pronounced effect on phase formation than calcination temperature. A calcination time of 10 h at 1000 °C resulted in negligible amount of BaCO₃. Such prolonged calcination treatment resulted in substantial grain growth in the SCS sample while the MCS samples were still in the nanocrystalline form. Absence of the ceria peak (464 cm^–1) in the Raman spectra confirmed the presence of a single perovskite BaCeO₃ phase in the sintered pellets as well.     

Physical,electrochemical and supercapacitive properties of activated carbon pellets from pre-carbonized rubber wood sawdust by CO2 activation

The physical and electrochemical properties of the activated carbon pellet electrodes have been investigated. Activated carbon pellets were prepared from single step carbonization process of pre-carbonized rubber wood sawdust at a temperature of 800 °C that followed with a CO₂ activation process at temperature in the range of 700–1000 °C. The BET characterization on the sample found that the surface area of the carbon pellet increased with the increasing of the activation temperature. The optimum value was as high as 683.63 m² g⁻¹. The electrical conductivity was also found to increase linearly with the increasing of the activation temperature, namely from 0.0075 S cm⁻¹ to 0.0687 S cm⁻¹ for the activation temperature in the range of 700–1000 °C. The cyclic voltammetry characterization of the samples in aqueous solution of 1 M H₂SO₄ also found that the specific capacitance increased with the increasing of the activation temperature. Typical optimum value was shown by the sample activated at 900 °C with the specific capacitance was as high as 33.74 F g⁻¹ (scan rate 1 mV s⁻¹). The retained ratio was as high as 32.72%. The activated carbon pellet prepared from the rubber wood sawdust may found used in supercapacitor applications.     

Synthesis and investigations on the stability of La0.8Sr0.2CuO2.4+δ at high temperatures

For application in solid oxide fuel cells La_0.8Sr_0.2CuO_2.4+δ was synthesized and the phase evolution was characterized after quenching from different temperatures and after slow cooling. A single phase perovskite was found after quenching from 950 °C. The electrical conductivity of the La_0.8Sr_0.2CuO_2.4+δ perovskite exhibited metallic behavior reaching values of about 270 S/cm at 800 °C in air. The thermal expansion between 30 and 800 °C gave a thermal expansion coefficient of 11.1 × 10^− 6 K^− 1.At higher temperatures, the perovskite was transformed to the K₂NiF₄-type structure via an intermediate stage that can be best described as a LaSrCuO₄ phase with preferential growing of {020} lattice planes. After sintering at 1100 °C and slow cooling in the furnace a phase mixture of (La,Sr)CuO_4+δ and (La,Sr)CuO_2.4+δ perovskite was obtained. This phase mixture showed higher electrical conductivity (400 S/cm at 800 °C) and smaller thermal expansion coefficient (9.6 × 10^− 6 K^− 1) than the single phase La_0.8Sr_0.2CuO_2.4+δ perovskite.