Synthesis of thermally-induced phase separating polymer with well-defined polymer structure by living cationic polymerization. I. Synthesis of poly(vinyl ether)s with oxyethylene units in the pendant and its phase separation behavior in aqueous solution

Living cationic polymerization of alkoxyethyl vinyl ether [CH₂?CHOCH₂CH₂OR; R: CH₃ (MOVE), C₂H₅ (EOVE)] and related vinyl ethers with oxyethylene units in the pendant was achieved by 1-(isobutoxy)ethyl acetate ( 1 )/Et_1.5AlCl_1.5 initiating system in the presence of an added base (ethyl acetate or THF) in toluene at 0°C. The polymers had a very narrow molecular weight distribution (M?_w/M?_n = 1.1–1.2) and the M?_n proportionally increased with the progress of the polymerization reaction. On the other hand, the polymerization by 1 /EtAlCl₂ initiating system in the presence of ethyl acetate, which produces living polymer of isobutyl vinyl ether, yielded the nonliving polymer. When an aqueous solution of the polymers thus obtained was heated, the phase separation phenomenon was clearly observed in each polymer at a definite critical temperature (T_ps). For example, T_ps was 70°C for poly(MOVE), and 20°C for poly(EOVE) (1 wt % aqueous solution, M?_n ～ 2 × 10⁴). The phase separation for each case was quite sensitive (ΔT_ps = 0.3–0.5°C) and reversible on heating and cooling. The T_ps or ΔT_ps was clearly dependent not only on the structure of polymer side chains (oxyethylene chain length and ω-alkyl group), but also on the molecular weight (M?_n = 5 × 10³-7 × 10⁴) and its distribution. © 1992 John Wiley & Sons, Inc.     

A novel palladium catalyst for the polymerization of propargyl alcohol

Homogeneous polymerization of propargyl alcohol (OHP) with Pd (C?CCH₂OH)₂(PPh₃)₂ [Pd?C] catalyst in CHCl₃-CH₃OH mixed solvent system has been investigated. [Pd?C] was found to be a novel effective catalyst for the OHP polymerization. Some features, kinetic behavior, and effect of solvent for the OHP polymerization are described and discussed. The overall polymerization activation energy was found to be 75.6kJ/mol and the rate equation can be expressed as R_p = k_p[OHP] [Pd?C]^0.7, where k_p = 3.14 × 10^-4 L^0.7/ mol^0.7 S (60°C). Polypropargyl alcohol (POHP) obtained is a brown powder with a number-average molecular weight (M?_n) of 10³-2 × 10³, and soluble in MeOH, DMF, and DMSO. Conducting properties of the resulting POHP were investigated. © 1994 John Wiley & Sons, Inc.     

Radical and cationic polymerizations of 3‐ethyl‐3‐methacryloyloxymethyloxetane

3‐Ethyl‐3‐methacryloyloxymethyloxetane (EMO) was easily polymerized by dimethyl 2,2′‐azobisisobutyrate (MAIB) as the radical initiator through the opening of the vinyl group. The initial polymerization rate (R_p) at 50 °C in benzene was given by R_p = k[MAIB]^0.55 [EMO]^1.2. The overall activation energy of the polymerization was estimated to be 87 kJ/mol. The number‐average molecular weight (M?_n) of the resulting poly(EMO)s was in the range of 1–3.3 × 10⁵. The polymerization system was found to involve electron spin resonance (ESR) observable propagating poly(EMO) radicals under practical polymerization conditions. ESR‐determined rate constants of propagation (k_p) and termination (k_t) at 60 °C are 120 and 2.41 × 10⁵ L/mol s, respectively—much lower than those of the usual methacrylate esters such as methyl methacrylate and glycidyl methacrylate. The radical copolymerization of EMO (M₁) with styrene (M₂) at 60 °C gave the following copolymerization parameters: r₁ = 0.53, r₂ = 0.43, Q₁ = 0.87, and e₁ = +0.42. EMO was also observed to be polymerized by BF₃OEt₂ as the cationic initiator through the opening of the oxetane ring. The M?_n of the resulting polymer was in the range of 650–3100. The cationic polymerization of radically formed poly(EMO) provided a crosslinked polymer showing distinguishably different thermal behaviors from those of the radical and cationic poly(EMO)s. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1269–1279, 2001     

Functional polyisobutylenes via electrophilic cleavage/alkylation

Lewis‐acid catalyzed degradation of poly(isobutylene‐co‐isoprene) (butyl rubber) in the presence of an alkoxybenzene compound was studied as a new route toward low molecular weight multifunctional polyisobutylenes. Simultaneous cleavage and functionalization of butyl rubber was conducted at ?70 °C and ?40 °C under TiCl₄ or AlCl₃ catalysis in 60/40 hexane/methylene chloride cosolvents in the presence of (3‐bromopropoxy)benzene (BPB) for various times up to 24 h. The butyl rubber (EXXON? Butyl 365) possessed M _n = 1.91 × 10⁵ g/mol, PDI = 1.66 (GPC/MALLS), and 2.30 mol % isoprene units (nearly exclusively trans ?1,4). At ?70 °C with TiCl₄, molecular weight was reduced to various values within the range 7 to 11 × 10³ g/mol depending on conditions; lower BPB concentration produced lower molecular weight. However, the ratio of isobutylene repeat units to BPB units (IB/Q ) remained constant at about 43:1, which is approximately the same as the ratio of isobutylene to isoprene repeat units (IB/IP) in the starting butyl rubber (42.5:1). At ?40 °C with TiCl₄, molecular weight was reduced to about 5 × 10³ g/mol, and IB/Q was reduced below IB/IP, indicating nearly a difunctional telechelic structure. AlCl₃ was a more active catalyst and produced results similar to TiCl₄ at ?40 °C, even when used at seven times lower concentration. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1991–1997     

Molecular weight distribution in radiation-induced polymerization. I. γ-radiation-induced free-radical polymerization of liquid styrene

The kinetics of γ-radiation-induced free-radical polymerization of styrene were studied over the temperature range 0–50°C at radiation intensities of 9.5 × 10⁴, 3.1 × 10⁵, 4.0 × 10⁵, and 1.0 × 10⁶ rad/hr. The overall rate of polymerization was found to be proportional to the 0.44–0.49 power of radiation intensity, and the overall activation energy for the radiation-induced free-radical polymerization of styrene was 6.0–6.3 kcal/mole. Values of the kinetic constants, k_p²/k_t and k_trm/k_p, were calculated from the overall polymerization rates and the number-average molecular weights. Gelpermeation chromatography was used to determine the number-average molecular weight M?_n, the weight-average molecular weight M?_w, and the polydispersity ratio M?_w/M?_n, of the product polystyrene. The polydispersity ratios of the radiation-polymerized polystyrene were found to lie between 1.80 and 2.00. Significant differences were observed in the polydispersity ratios of chemically initiated and radiation-induced polystyrenes. The radiation chemical yield, G(styrene), was calculated to be 0.5–0.8.     

Anionic homopolymerization of ferrocenylmethyl methacrylate

Anionic polymerization of ferrocenylmethyl methacrylate (FMMA) was investigated using high-vacuum techniques. Initiators used included n-butyllithium, sodium naphthalide, potassium naphthalide, Grignard reagents (both C₂H₅MgBr and C₆H₅MgBr), sodium methoxide, and lithium aluminum hydride. FMMA polymerization was readily initiated by each of the above initiators with the exception of sodium methoxide. The molecular weight of poly(ferrocenylmethyl methacrylate) could be controlled by varying the monomer-to-initiator ratio when lithium aluminum hydride was used in tetrahydrofuran (THF). In this system, poly(ferrocenylmethyl methacrylate), soluble in benzene or THF, was prepared with M?_n as high as 277,000 with a relatively narrow molecular weight distribution compared to samples prepared by radical-initiated polymerization. The Mark-Houwink values of K and a, determined in THF, were K = 4.94 × 10^?2 and a = 0.53 (when M = M?_n) and K = 3.72 × 10^?2 and a = 0.51 (when M = M?_w). It is clear that the polymer is moderately coiled in THF.     

Polymerization of acrylamide with persulfate–thiomalic acid initiator

The redox system of potassium persulfate–thiomalic acid (I₁–I₂) was used to initiate the polymerization of acrylamide (M) in aqueous medium. For 20–30% conversion the rate equation is where R_p is the rate of polymerization. Activation energy is 8.34 kcal deg^?1 mole^?1 in the investigated range of temperature 25–45°C. M_n is directly proportional to [M] and inversely to [I₁]. The range of concentrations for which these observations hold at 35°C and pH 4.2 are [I₁] = (1.0–3.0) × 10^?3, [I₂] = (3.0–7.5) × 10^?3, and [M] = 5.0 × 10^?2–3.0 × 10^?1 mole/liter.     

Aromatic poly(amic acids): Fundamental structural studies

Aromatic poly(amic acids) derived from pyromellitic dianhydride and 4,4′,-diaminodiphenyl ether were characterized by dilute solution techniques. Number-average molecular weights M?_n of 13 samples ranged from 13,000 to 55,000 (DP 31–131). Weight-average molecular weights M?_w of 21 samples ranged from 9,900 to 266,000. The ratio M?_w/M?_n was between 2.2 and 4.8. Heterogeneous polymerization yielded higher molecular weight polymer than homogeneous polymerization. The molecular weight could be varied systematically by control of stoichiometric imbalance. Use of very pure monomers and solvent gave polymers of relatively high number-average molecular weight (～50, 000) and the most probable molecular weight distribution M?_w/M?_n = 2. Impure monomers and/or solvent resulted in lower number-average molecular weight (M?_n ? 20,000–30,000) and wider distributions (M?_w/M?_n = 3–5). The Mark-Houwink relation obtained was [η] = 1.85 × 10^?4M?_w^0.80 The exponent is characteristic of moderately extended solvated coils. The unperturbed chain dimensions (r₀² /M)^1/2 were 0.848 A., and the steric factor σ was 1.24 which is close to the limiting value of unity for an equivalent chain with free internal rotations. The sedimentation constant–molecular weight relation was S₀ = 2.70 × 10^?2M?_w^0.39. This exponent is consistent with the Mark-Houwink exponent.     

Excluded-volume effects in dilute polymer solutions. IV. Polyisobutylene

Statistical radii of gyration, second virial coefficients, and intrinsic viscosities of sharp fractions (M?_w/M?_n ≈ 1.1) of polyisobutylene (PIB) covering a wide range of molecular weight (1.6 × 10⁵ to 4.7 × 10⁶) were determined in isoamyl isovalerate (IAIV) at a number of temperatures ranging from 20 to 60°C, in n-heptane at 25°C, and in cyclohexane at 25°C by light-scattering and viscosity measurements. It was found that IAIV at 22.1°C is a theta solvent for PIB. Analysis of the data by the methods described in preceding papers of this series indicated that, except for minor differences, the conclusions derived from similar studies with polychloroprene, polystyrene, and poly-p-methylstyrene hold equally for solutions of the typical linear polymer investigated here. In particular, no decisive evidence for the drainage effect was found.     

Amino alcohol additives for the fast living radical polymerization of methyl methacrylate with RuCl2(PPh3)3

A series of amino alcohols [e.g., R₂N (CH₂)_n OH (R = Me, Et, etc.; n = 2, 3, or 4)] were examined as additives for rate enhancement and finer reaction control in the living radical polymerization of methyl methacrylate with RuCl₂(PPh₃)₃. In general, these additives were more effective in acceleration than the corresponding amines as well as mixtures of an amine and a nonsubstituted alcohol, diamines, or diols. For example, 2-(diethylamino)ethanol significantly accelerated the polymerization (23 h, 91% at 60 °C) and gave polymers with narrower molecular weight distributions [weight-average molecular weight/number-average molecular weight (M_w/M_n) = 1.23], with respect to the system without the additive (550 h, 95%, M_w/M_n ∼ 2.0 at 80 °C; no polymerization at 60 °C). ¹H NMR analysis showed the interaction between the amino alcohols and RuCl₂(PPh₃)₃, which apparently formed a more active catalyst. Amino alcohols were also effective in Ru(Ind)Cl(PPh₃)₂-catalyzed systems (96% in 8 h at 80 °C). High-molecular-weight poly(methyl methacrylate) (M_n ∼ 1.1 × 10⁵) was synthesized with the RuCl₂(PPh₃)₃/2-(diethylamino)ethanol system, in which the polymerization reached 97% conversion in 4 h. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3597–3605, 2003     

Radiation-induced heterogeneous polymerization of ethylene in the presence of ethyl alcohol

The radiation-induced heterogeneous polymerization of ethylene in ethyl alcohol was carried out in a reactor with a capacity of 100 ml under the following reaction conditions: temperature, 24 ± 3°C; pressure, 200–400 kg/cm²; amount of ethyl alcohol, 30–70 ml; dose rate, 3.7 × 10⁴?1.05 × 10⁵ rad hr. The effects of amount of ethyl alcohol, pressure, and dose rate on the rate of polymerization at the steady state, the amount of polymerized monomer, the molecular weight of polymer, and the number of polymer chains were studied compared with the results obtained in the polymerization in tert-butyl alcohol. It was found that there is an acceleration period in the early stage of reaction followed by a steady state. The rate of polymerization was maximum when about 50 ml of ethyl alcohol was used. The molecular weight of polymer increased with a decrease in the amount of ethyl alcohol. The dependences of pressure (p) and dose rate (I) on the rate of polymerization at steady state (R_s) and the molecular weight of polymer (M?_n) were expressed as follows; R_s ∝ p^0.74, M?_n ∝ p^0.3?0.4, R_s ∝ I^0.9 and M?_n ∝ I^{?0.1 ?0.0}. The results were analyzed by a kinetic treatment based on a reaction mechanism containing both first-and second-order terminations. The rate constant of first-order termination by radical occlusion was considerably larger than that in the polymerization in tert-butyl alcohol, because the affinity of ethyl alcohol for polyethylene is smaller than that of tert-butyl alcohol. It was found that chain transfer to ethyl alcohol takes place easily and the G value of ethyl alcohol for initiation is larger than 1.5.     

Organometallic polymers. XIV. Copolymerization of vinylcyclopentadienyl manganese tricarbonyl and vinylferrocene with N-vinyl-2-pyrrolidone

N-Vinyl-2-pyrrolidone(I) has been copolymerized with vinylferrocene(II) and vinylcyclopentadienyl manganese tricarbonyl(III) in degassed benzene solutions with the use of azobisisobutyronitrile (AIBN) as the initiator. The polymerizations proceed smoothly, and the relative reactivity ratios were determined as r₁ = 0.66, r₂ = 0.40 (for copolymerization of I with II, M₁ defined as II) and r₁ = 0.14 and r₂ = 0.09 (for copolymerization of I with III, M₁ defined as III). These copolymers were soluble in benzene, THF, chloroform, CCl₄, and DMF. Molecular weights were determined by viscosity and gel-permeation chromatography studies (universal calibration technique.) The copolymers exhibited values of M?_n between 5 × 10³ and 10 × 10³ and M?_w between 7 × 10³ and 17 × 10³ with M?_w/M?_n < 2. Upon heating to 260°C under N₂, copolymers of III underwent gas evolution and weight loss. The weight loss was enhanced at 300°C, and the polymers became in creasingly insoluble. Copolymers of vinylferrocene were oxidized to polyferricinium salts upon treatment with dichlorodicyanoquinone (DDQ) or o-chloranil (o-CA) in benzene. Each unit of quinone incorporated into the polysalts had been reduced to its radical anion. The ratio of ferrocene to ferricinium units in the polysalts was determined. The polysalts did not melt at 360°C and were readily soluble only in DMF.     

Radical polymerization behavior of trimethoxyvinylsilane

Trimethoxyvinylsilane (TMVS) was quantitatively polymerized at 130 °C in bulk, using dicumyl peroxide (DCPO) as initiator. The polymerization of TMVS with DCPO was kinetically studied in dioxane by Fourier transform near‐infrared spectroscopy. The overall activation energy of the bulk polymerization was estimated to be 112 kJ/mol. The initial polymerization rate (R_p) was expressed by R_p = k[DCPO]^0.6[TMVS]^1.0 at 120 °C, being closely similar to that of the conventional radical polymerization involving bimolecular termination. The polymerization system involved electron spin resonance (ESR) spectroscopically observable polymer radicals under the actual polymerization conditions. ESR‐determined apparent rate constants of propagation and termination were 13 L/mol s and 3.1 × 10⁴ L/mol s at 120 °C, respectively. The molecular weight of the resulting poly(TMVS)s was low (M_n = 2.0–4.4 × 10³), because of the high chain transfer constant (C_mtr = 4.2 × 10^?2 at 120 °C) to the monomer. The bulk copolymerization of TMVS (M₁) and vinyl acetate (M₂) at 120 °C gave the following copolymerization parameters: r_l = 1.4, r₂ = 0.24, Q₁ = 0.084, and e₁ = +0.80. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5864–5871, 2005     

Acyclic diene metathesis polymerization of 2,5‐dialkyl‐1,4‐divinylbenzene with molybdenum or ruthenium catalysts: Factors affecting the precise synthesis of defect‐free,high‐molecular‐weight trans‐poly(p‐phenylene vinylene)s

Factors affecting the syntheses of high‐molecular‐weight poly(2,5‐dialkyl‐1,4‐phenylene vinylene) by the acyclic diene metathesis polymerization of 2,5‐dialkyl‐1,4‐divinylbenzenes [alkyl = n‐octyl ( 2 ) and 2‐ethylhexyl ( 3 )] with a molybdenum or ruthenium catalyst were explored. The polymerizations of 2 by Mo(N‐2,6‐Me₂C₆H₃) (CHMe₂ Ph)[OCMe(CF₃)₂]₂ at 25 °C was completed with both a high initial monomer concentration and reduced pressure, affording poly(p‐phenylene vinylene)s with low polydispersity index values (number‐average molecular weight = 3.3–3.65 × 10³ by gel permeation chromatography vs polystyrene standards, weight‐average molecular weight/number‐average molecular weight = 1.1–1.2), but the polymerization of 3 was not completed under the same conditions. The synthesis of structurally regular (all‐trans), defect‐free, high‐molecular‐weight 2‐ethylhexyl substituted poly(p‐phenylene vinylene)s [poly 3 ; degree of monomer repeating unit (DP_n) = ca. 16–70 by ¹H NMR] with unimodal molecular weight distributions (number‐average molecular weight = 8.30–36.3 × 10³ by gel permeation chromatography, weight‐average molecular weight/number‐average molecular weight = 1.6–2.1) and with defined polymer chain ends (as a vinyl group, ? CH?CH₂) was achieved when Ru(CHPh)(Cl)₂(IMesH₂)(PCy₃) or Ru(CH‐2‐OⁱPr‐C₆H₄)(Cl)₂(IMesH₂) [IMesH₂ = 1,3‐bis(2,4,6‐trimethylphenyl)‐2‐imidazolidinylidene] was employed as a catalyst at 50 °C. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6166–6177, 2005     

Determination of molecular weight distribution of cellulose by conversion into tricarbanilate and fractionation

Two samples of cellulose (molecular weight 2.97 × 10⁵ and 1.25 × 10⁵) were transformed into carbanilates (CTC) which were then fractionated by the elution method at a constant composition of the acetone-water elution mixture with the column temperature gradually increasing from ?30°C to 30°C, and by the GPC method in acetone and tetrahydrofuran. Tetrahydrofuran appeared to be a more suitable solvent. The molecular weights of fractions obtained by the elution fractionation were determined by the light-scattering method in tetrahydrofuran. The width of fractions was determined by the GPC method (average M _w/M _n = 1.37); the [η] values and the Mark-Houwink constants (K = 5.3 × 10^-3, a = 0.84) for tetrahydrofuran at 25°C were determined. The calibration curve for the GP method was constructed by means of the fractions thus obtained; it was demonstrated that the universal calibration curve according to Benoit can also be used. It was demonstrated that the molecular weight distribution of cellulose can be conveniently determined by conversion into CTC followed either by the elution fractionation (for preparative purposes) or by fractionation by the GPC method (for analytical purposes).     

Properties of crystallized trans 1,4-polyisoprene

Stirrer crystallization of a trans-1,4-polyisoprene fraction(M?_n = 3 × 10⁵) was carried out from n-butyl acetate and from n-heptane solutions (2% w/v). Fibrous crystals in the ß form were obtained at temperatures of 46-48°C in the two solvents, respectively. At 36-46°C from n-butyl acetate and 25-35°C from n-heptane lamellar crystallization took place leading predominantly to the α form. Melting endotherms and densities for various samples were obtained. The maximum TENDO for α was 74°C and for ß 79°C and the maximum weight fraction crystallinity for ß was 0.78. The stability of performed α nuclei in n-butyl acetate and n-heptane using a fraction with M?_n = 2.5 × 10⁵ was monitored as a function of temperature. The dissolution temperature of fibrous ß-TPI with the maximum TENDO was measured in 13 liquids and the results analyzed in terms of the Flory-Huggins parameter. The heats of fusion for the α and ß forms, obtained by extrapolation of heat of fusion versus change in specific volume, were found to be 8.0 and 10 kJ mol^?1, respectively. The pressure coefficients of the melting temperature were calculated to be 38 and 43 K kbar^?1 and the fold-surface free energies recalculated to be 42 ± 1 and 53 ± 1 erg cm^?2 for the α and ß forms, respectively. The number of monomer units per average noncrystalline chain traverse for the most crystalline fibrous ß-TPI was estimated at 36.     

Charge transfer polymerization of 2-vinyl pyridine initiated by n-butyl amine and carbon tetrachloride

2-Vinyl pyridine (2-VP) can be initiated by a charge-transfer complex formed by the interaction of aliphatic amines such as n-butylamine (nBA) and carbon tetrachloride (CCl₄) in a solvent like NN-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO). This article describes the polymerization of 2-VP by n-butylamine (nBA) in the presence of carbon tetrachloride in DMSO at 60°C. The rate of polymerization R_p increases rapidly with carbon tetrachloride (CCl₄) up to a concentration of 3.93 mol/L, but for a higher concentration it is almost independent of the carbon tetrachloride concentration; R_p is proportional to [nBA]^0.5 and [2-VP]^1.5 when [CCl₄]>[nBA]. The average rate constant k is 1.03 × 10^?5 L/mol s. When [CCl₄] < [nBA] the rate constant in terms of [2-VP] was 1.06 × 10^?5 s^?1 at 60°C and the overall rate constant was 1.035 × 10^?5 L/mol s at 60°C.     

Solution properties of high molecular weight polystyrene

A series of polystyrenes with weight-average molecular weight M?_w up to 1.3 × 10⁷ was prepared by anionic polymerization in tetrahydrofuran (THF). Each sample was characterized by gel-permeation chromatography, light scattering, and viscometry. It was found that each sample had an almost symmetrical and very narrow molecular weight distribution (M?_w/M?_n < 1.07). The mean-square unperturbed radius of gyration 〈S²〉₀ was determined in trans-decalin at 20.4°C as 〈S²〉₀ = 7.8₆ × 10^?18M?_w (cm²). The particle scattering factor was well represented by the Debye equation irrespective of solvent in the range of M?_w < 4 × 10⁶, and only a small deviation was observed in benzene at higher molecular weights. The penetration function Ψ ≡ A₂M²/4π^3/2N_A〈S〉^23/2 was found to approach a relatively low asymptotic value of 0.21–0.23 at molecular weights above 2 × 10⁶ in benzene at 30°C, where A₂ is the second virial coefficient and N_A is Avogrado's number. It was also found that the theta temperature in trans-decalin was affected by the nature of polymer samples. A difference of about 3°C in the theta temperature was observed between two series of anionic polystyrenes, one prepared in THF and the other in benzene, but there was practically no difference in unperturbed chain dimension.     

Gamma-ray induced polymerization of styrene in the presence of methanol

The kinetics and molecular weight distributions (MWD) of the gamma-ray induced polymerization of styrene in methanol were studied at 35°C, at low conversions and over a dose rate range of 2.76 × 10³ to 2.74 × 10⁴ rad/hr. The data obtained at low initial methanol content agreed with previously obtained results and the MWD of the polystyrene formed yielded a single unimodal peak with M?_n in the range of 35,000–480,000. However, at high initial methanol content and low dose rates, at least three peaks were clearly discernible over wide molecular weight distributions. The existence of these peaks is related to the kinetic data and the formation of three distinguishable regions in the polymerization system.     

Cationic 1,2-vinyl addition polymerization of cyclic ketene acetals initiated by conventional acids

Pure 1,2-addition polymers, poly(2-methylene-1,3-dioxolane), 1b , poly(2-methylene-1,3-dioxane), 2b , and poly(2-methylene-5,5-dimethyl-1,3-dioxane), 3b , were prepared using the cationic initiators H₂SO₄, TiCl₄, BF₃, and also Ru(PPh₃)₃Cl₂. Small ester carbonyl bands in the IR spectra of 1b and 2b were observed when the polymerizations were performed at 80°C ( 1b ) and both 67 and 138°C ( 2b ) using Ru(PPh₃)₃Cl₂. The poly(cyclic ketene acetals) were stable if they were not exposed to acid and water. They were quite thermally stable and did not decompose until 290°C ( 1b ), 240°C ( 2b ), and 294°C ( 3b ). Different chemical shifts for axial and equatorial H and CH₃ on the ketal rings were found in the ¹H NMR spectrum of 3b at room temperature. High molecular weight 3b (M̄_n = 8.68 × 10⁴, M̄_w = 1.31 × 10⁵, M̄_z = 1.57 × 10⁵) was obtained upon cationic initiation by H₂SO₄. Poly(2-methylene-1,3-dioxane), 2b , underwent partial hydrolysis when Ru(PPh₃)₃Cl₂ and water were present in the polymer. The hydrolyzed products were 1,3-propanediol and a polymer containing both poly(2-methylene-1,3-dioxane) and polyketene units. The percentages of these two units in the hydrolyzed polymer were about 32% polyketene and 68% poly(2-methylene-1,3-dioxane). No crosslinked or aromatic structures were observed in the hydrolyzed products. The molecular weight of hydrolyzed polymer was M̄_n = 5740, M̄_w = 7260, and M̄_z = 9060. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3707–3716, 1997