低雷诺数俯仰振荡翼型等离子体流动控制

针对低雷诺数翼型气动性能差的特点, 通过介质阻挡放电(dielectric barrier discharge, DBD)等离子体激励控制的方法, 提高翼型低雷诺数下的气动特性,改善其流场结构. 采用二维准直接数值模拟方法求解非定常不可压Navier-Stokes方程,对具有俯仰运动的NACA0012翼型的低雷诺数流动展开数值模拟.同时将介质阻挡放电激励对流动的作用以彻体力源项的形式加入Navier-Stokes方程,通过数值模拟探究稳态DBD等离子体激励对俯仰振荡NACA0012翼型气动特性和流场特性的影响.为了进行流动控制, 分别在上下表面的前缘和后缘处安装DBD等离子体激励器,并提出四种激励器的开环控制策略,通过对比研究了这些控制策略在不同雷诺数、不同减缩频率以及激励位置下的控制效果.通过流场结构和动态压强分析了等离子体进行流场控制的机理. 结果表明,前缘DBD控制中控制策略B(负攻角时开启上表面激励器,正攻角时开启下表面激励器)效果最好,后缘DBD控制中控制策略C(逆时针旋转时开启上表面激励器,顺时针旋转时开启下表面激励器)效果最好,前缘DBD控制效果会随着减缩频率的增大而下降, 同时会导致阻力增大.而后缘DBD控制可以减小压差阻力, 优于前缘DBD控制,对于计算的所有减缩频率(5.01~11.82)都有较好的增升减阻效果.在不同雷诺数下, DBD控制的增升效果较为稳定, 而减阻效果随着雷诺数的降低而变差,这是由流体黏性效应增强导致的.      

Skin-friction drag reduction in a channel flow with streamwise-aligned plasma actuators

Direct Numerical Simulations in a turbulent channel flow at a moderate Reynolds number are performed in order to investigate the potential of Dielectric Barrier Discharge (DBD) plasma actuators for the reduction of the skin-friction drag. The idea is to use a sparse array of streamwise-aligned plasma actuators to produce near-wall spanwise-orientated jets in order to destroy the events which transport high-speed fluid towards the wall. It is shown that it is possible to reduce the drag by about 33.5% when the streamwise-aligned actuators are configured to generate appropriate spanwise-orientated jets very close to the wall so that the sweeps which are mainly responsible for the skin-friction are destroyed. We demonstrate that it is possible to achieve significant drag reduction with a sparse array of streamwise-aligned plasma actuators, with one order of magnitude less actuators than previous experiments in a similar set-up.     

双振子同异步振动主动控制湍流边界层减阻实验研究

本文以镶嵌在平板上沿展向对放的两个压电陶瓷振子为主动控制激励器,自主设计了零质量射流主动控制湍流边界层减阻实验方案.在风洞中开展了双压电振子同步和异步振动主动控制湍流边界层减阻的实验研究,实现了压电振子的周期扰动对湍流边界层多尺度相干结构的干扰和调制,施加控制后减小了壁面摩擦阻力,获得减阻效果.当异步控制100 V, 160 Hz工况时得到最大减阻率为18.54%.小波多尺度分析结果表明,施加控制工况中PZT振子的周期性扰动使得小尺度结构的湍流脉动强度增强,改变了近壁区大尺度和小尺度结构的含能分布,且异步控制工况比同步控制工况的减阻效果好.当双振子振动频率为160 Hz时,流向脉动速度的小波系数PDF曲线呈现出波动特征,尾部变宽显著,近壁湍流脉动更加有序和规则,湍流间歇性减弱.对小尺度脉动进行条件相位平均的结果表明,施加PZT周期扰动后使得大尺度结构破碎成为小尺度结构,小尺度脉动强度增强,实现减阻.随着流向位置离PZT振子越来越远,周期性扰动对相干结构的调制作用逐渐减弱.     

Large Eddy Simulation of Flow Control Around a Cube Subjected to Momentum Injection

The concept of Momentum Injection (MI) through Moving Surface Boundary layer Control (MSBC) applied to a cubic structure is numerically studied using Large Eddy Simulation at a Reynolds number of 6.7×10⁴. Two small rotating cylinders are used to add the momentum at the front vertical edges of the cube. Two configurations are studied with the yaw angle of 0° and 30°, respectively, with ratio of the rotation velocity of cylinders and the freestream velocity of 2. The results suggest that MI delays the boundary layer separation and reattachment, and thus reduces the drag. A drag reduction of about 6.2 % is observed in the 0° yaw angle case and about 44.1 % reduction in the 30° yaw angle case. In the case of 0° yaw angle, the main change of the flow field is the disappearance of the separation regions near the rotating cylinders and the wake region is slightly changed due to MI. In the 30° yaw angle case, the flow field is changed a lot. Large flow separations near one rotating cylinder and in the wake is significantly reduced, which results in the large drag reduction. Meanwhile, the yaw moment is increased about 50.5 %.     

On the generation of yawing moment using active flow control

The generation of control moments without moving control surfaces is of great practical importance. Following a successful flight demonstration of creating roll motion without ailerons using differential, lift oriented, flow control the current study is a first step towards generating yawing motion via differential flow controlled drag.A wind tunnel study was conducted on a 21% thick Glauert type airfoil. The upper surface flow is partially separated from the two-thirds chord location and downstream on this airfoil at all incidence angles. An array of mass-less Piezo-fluidic actuators, located at x/c = 0.65, are capable of fully reattaching the flow in a gradual, controlled manner. The actuators are individually operated such that the boundary layer could be controlled in a 3D fashion.Several concepts for creating yaw motion without moving control surface are examined. The ultimate goal is to generate the same lift on both wings, while decreasing the drag on one wing and increasing the drag on the other, therefore creating a yawing moment. Decreased drag is created by effective part-span separation delay while increased drag can be created by enhanced generation of vortex shedding or by highly localized 3D actuation.Detailed measurements of 3D surface pressure distributions and wake data with three velocity and streamwise vorticity components are presented and discussed along with surface flow visualization images. The data provide evidence that yawing moments can be generated with AFC.     

横摆角下汽车尾部湍流特征量的PIV试验分析

汽车尾部湍流场是汽车压差阻力的主要来源,在HD-2汽车模型风洞中,首先使用测力天平和测压系统,对横摆角工况下汽车模型的气动六分力和纵对称截面48个测点的表面压力进行了测量,然后利用PIV测量技术对模型在横摆角分别为0°、15°的尾部湍流场进行了测量,获得该模型尾流场的速度场、涡量场和雷诺应力流场信息,通过计算得出尾流场区域空间相关系数和湍流积分尺度。结果表明:在横摆角工况下,汽车模型尾部涡流的结构呈现向上发展的趋势;尾流场拖拽涡的范围和强度的增大导致了模型气动力出现较大的增加;湍流积分尺度的变化表明,尾部涡流区的分离噪声与涡流分离位置有关,在汽车尾部造型设计中,要尽量推迟尾部涡流的分离。     

基于分布式合成双射流的飞行器无舵面三轴姿态控制飞行试验

将自主可控的合成双射流激励器集成于常规布局飞行器中, 进行了三轴无舵面控制飞行试验, 验证了分布式合成双射流对飞行器巡航时的无舵面姿态调控能力. 对合成双射流激励器进行改进, 设计了分布式三轴姿态控制合成双射流激励器, 滚转环量控制激励器分别安装于两侧机翼翼尖处后缘, 射流出口靠近压力面; 偏航反向合成双射流控制激励器分别安装于靠近两侧机翼翼尖20%弦长处, 上、下沿展向均匀布置; 俯仰环量控制激励器安装于V尾下的平尾后缘, 射流出口靠近压力面. 针对巡航速度为30 m/s的飞行器, 进行了三轴姿态控制飞行试验, 结果表明: 分布式合成双射流实现了飞行器巡航时的三轴无舵面姿态操控; 横航向控制存在耦合, 滚转环量控制激励器实现了飞行器的双向滚转操控, 能产生的最大滚转角速度达16.87°/s, 偏航反向合成双射流控制激励器实现了飞行器的双向偏航操控, 能产生的最大偏航角速度达9.09°/s; 俯仰环量控制激励器实现了飞行器的纵向控制, 能产生的最大俯仰角速度达7.68°/s.      

Investigation of turbulent flow past a yawed wavy cylinder

A large eddy simulation (LES) study was conducted to investigate the three-dimensional characteristics of the turbulent flow past wavy cylinders with yaw angles from 0° to 60° at a subcritical Reynolds number of 3900. The relationships between force coefficients and vortex shedding frequency with yaw angles for both wavy cylinders and circular cylinders were investigated. Experimental measurements were also performed for the validation of the present LES results. Comparing with corresponding yawed circular cylinders at similar Reynolds number, significant differences in wake vortex patterns between wavy cylinder and circular cylinder were observed at small yaw angles. The difference in wake pattern becomes insignificant at large yaw angles. The mean drag coefficient and the Strouhal number obey the independence principle for circular cylinders at yaw angle less than 45°, while the independence principle was found to be unsuitable for yawed wavy cylinders. In general, the mean drag coefficients and the fluctuating lift coefficients of a yawed wavy cylinder are less than those of a corresponding yawed circular cylinder at the same flow condition. However, with the increase of the yaw angle, the advantageous effect of wavy cylinder on force and vibration control becomes insignificant.     

Large-Eddy BreakUp Devices – a 40 Years Perspective from a Stockholm Horizon

In the beginning of the 1980’s Large Eddy BreakUp (LEBU) devices, thin plates or airfoils mounted in the outer part of turbulent boundary layers, were shown to be able to change the turbulent structure and intermittency as well as reduce turbulent skin friction. In some wind-tunnel studies it was also claimed that a net drag reduction was obtained, i.e. the reduction in skin-friction drag was larger than the drag on the devices. However, towing-tank experiments with a flat plate at high Reynolds numbers as well as with an axisymmetric body showed no net reduction, but instead an increase in total drag. Recent large-eddy simulations have explored the effect of LEBUs on the turbulent boundary layer and evaluations of the total drag show similar results as in the towing tank experiments. Despite these negative results in terms of net drag reduction, LEBUs manipulate the boundary layer in an interesting way which explains why they still attract some interest. The reason for the positive results in the wind-tunnel studies as compared to drag measurements are discussed here, although no definite answer for the differences can be given.     

Dielectric-barrier-discharge vortex generators: characterisation and optimisation for flow separation control

We investigated the use of dielectric-barrier-discharge plasma actuators as vortex generators for flow separation control applications. Plasma actuators were placed at a yaw angle to the oncoming flow, so that they produced a spanwise wall jet. Through interaction with the oncoming boundary layer, this created a streamwise longitudinal vortex. In this experimental investigation, the effect of yaw angle, actuator length and plasma-induced velocity ratio was studied. Particular attention was given to the vortex formation mechanism and its development downstream. The DBD plasma actuators were then applied in the form of co-rotating and counter-rotating vortex arrays to control flow separation over a trailing-edge ramp. It was found that the vortex generators were successful in reducing the separation region, even at plasma-to-free-stream velocity ratios of less than 10%.     

Drag force on a free surface-piercing yawed circular cylinder in steady flow

The force distribution on a surface-piercing yawed cylinder surface differs significantly from that on a surface-piercing vertical cylinder. The established numerical model for flow past the surface-piercing yawed cylinder with yaw angles from −45° to 45° was solved by the standard large-eddy simulation (LES) methodology. Six cases at intervals of ±15° relative to the vertical were studied at the Reynolds number of 27 000 and the Froude number of 0.8 based on the cylinder diameter and free-stream velocity, among which the drag forces on four cylinders with yaw angles from −15° to 30° were tested for the validation of the LES approach. The results revealed that the time-averaged total drag coefficient for all cases increases with the increase of yaw angle compared to that of the surface-piercing vertical cylinder, even over 2.5 for the ±45°-yawed cylinders. The sectional drag coefficients for the negatively yawed cylinders are much greater than that for the vertical cylinder, and much less for the positively yawed cylinders. The unbalanced hydrostatic pressures on the inclined section are mainly responsible for those increment and decrement. Once the hydrostatic pressure was removed, the sectional drag coefficient on the mid-span of the positively yawed cylinder increases from the top section to the bottom, and decreases for the negatively yawed cylinder. The corresponding integrated total drag coefficient decreases with the increase of the yaw angle to ±15°, then increases with the further increase of the magnitude of yaw angle.     

Generic Transport Aft-body Drag Reduction using Active Flow Control

Active flow-separation control is an effective and efficient mean for drag reduction and unsteady load alleviation resulting from locally or massively separated flow. Such a situation occurs in configurations where the aerodynamic performance is of secondary importance to functionality. The performance of heavy transport helicopters and aeroplanes, having a large, and almost flat, aft loading ramp suffer from the poor aerodynamics of the aft body. Hence, a combined experimental and numerical investigation was undertaken on a generic transport aeroplane/helicopter configuration. The experimental study provided surface pressures, direct drag measurements, surface and smoke flow visualization. The baseline flow was numerically analyzed, using finite volume solutions of the RANS equations. The baseline flow around the model was insensitive to the Reynolds number in the range it was tested. The flow separating from the aft body was characterized by two main sources of drag and unsteadiness. The first is a separation bubble residing at the lower ramp corner and the second is a pair of vortex systems developing and separating from the sides of the ramp. As the model incidence is decreased, the pair of vortex systems also penetrates deeper towards the centerline of the ramp, decreasing the pressure and increasing the drag. As expected, the ramp lower corner bubble was highly receptive to periodic excitation introduced from four addressable piezo-fluidic actuators situated at the ramp lower corner. Total drag was reduced by 3–11%, depending on the model incidence. There are indications that the flow in the wake of the model is also significantly steadier when the bubble at the lower ramp corner is eliminated. The vortex system is tighter and steadier when the ramp-corner bubble is eliminated.     

超声速钝体逆向喷流减阻的数值模拟研究

为研究逆向喷流技术对超声速钝体减阻的影响,采用标准k-ε湍流模型,通过求解二维Navier-Stokes方程对超声速球头体逆向冷喷流流场进行了数值模拟,并着重分析了喷口总压、喷口尺寸对流场模态和减阻效果的影响。计算结果显示:随着喷流总压的变化,流场可出现两种流动模态,即长射流穿透模态和短射流穿透模态;喷流能使球头体受到的阻力明显减小;存在最大减阻临界喷流总压值(在所研究参数范围内最大减阻可达51.1%);在其它喷流物理参数不变时,随着喷口尺寸的增大,同一流动模态下的减阻效果下降。本文的研究对超声速钝体减阻技术在工程上的应用具有一定的参考价值。     

Polymer drag reduction with surface roughness in flat-plate turbulent boundary layer flow

Experimental results from a study of surface roughness effects on polymer drag reduction in a zero-pressure gradient flat-plate turbulent boundary layer are presented. Both slot-injected polymer and homogeneous polymer ocean cases were considered over a range of flow conditions and surface roughness. Balance measurements of skin friction drag reduction are presented. Drag reductions over 60% were measured for both the injected and homogeneous polymer cases even with fully rough surfaces. As the roughness increased, higher polymer concentration was required to achieve a given level of drag reduction for the homogeneous case. With polymer injection, increasing surface roughness caused the drag reduction to decrease to low levels more quickly when the polymer expenditure was decreased or the freestream velocity was increased. However, the percent drag reductions on the rough surfaces with polymer injection were often substantially larger than on the smooth surface. Remarkably, in some cases, the skin friction drag force on a rough surface with polymer injection was less than the drag force observed on a smooth surface at comparable conditions. An erratum to this article can be found at     

等离子体激励器控制圆柱绕流的实验研究

为了发展新型移动附面层控制技术,提升流动控制效率,采用粒子图像测速技术,开展了基于对称布局等离子体气动激励的圆柱绕流控制研究,获得了静止空气下,对称布局激励器诱导流场的演化过程,评估了来流条件下等离子体控制效果,通过等离子体诱导涡实现了虚拟移动附面层控制,分析了诱导涡随时间演化的过程,揭示了圆柱绕流等离子体控制机理.结果表明:(1)在静止空气下,对称布局激励器在刚启动瞬间,会在暴露电极两侧诱导产生一对旋转方向相反的启动涡;随着时间的推移,启动涡逐渐向远离壁面的方向运动;随后,激励器在暴露电极两侧产生了两股速度近似相等,方向相反的诱导射流,诱导射流在柯恩达效应的影响下,朝壁面方向发展.(2)当激励电压峰峰值为19.6 kV,激励频率3kHz时,施加等离子体气动激励后,圆柱脱落涡得到了较好抑制,圆柱阻力系数减小了21.8％;(3)在来流作用下,对称布局激励器在靠近来流一侧,诱导产生了较为稳定的涡结构.诱导涡通过旋转、运动,促进了壁面附近低能气流与主流之间的掺混,抑制了圆柱绕流流场分离,实现了"虚拟移动附面层控制"效果.与传统移动附面层控制技术相比,基于等离子体气动激励的新型移动附面层控制技术不需要复杂、笨重的机构,不会带来额外的阻力,具有潜在的应用前景.      

电磁极宽度对圆柱绕流场影响的数值分析

在雷诺数Re=200的情况,利用Maxwell方程直接数值计算表面包覆电极与磁极圆柱体产生的电磁力分布,将其加入到动量方程中,在各种电磁力作用参数和电磁极宽度的组合下,对表面覆盖电磁极圆柱体在弱电解质中的绕流场结构及其升阻力特性进行了数值模拟与分析.结果表明,当电磁极宽度较小时,圆柱体绕流场的分离点越容易接近后驻点,而电磁力对总阻力的影响并不明显,但对压差和摩擦阻力均有明显影响.当电磁极宽度较大时,圆柱体尾部区域越容易产生射流现象,而且总阻力随电磁力作用参数和电磁极宽度增大而减小.在电磁力尚不足以完全抑制周期性涡脱落的情况下,升力幅值随电磁力作用参数增大而减小,但随电磁极宽度则先减小后略有增加,升力脉动频率则均随电磁力作用参数和电磁极宽度增大而增加.研究表明,电磁力可以有效地改善圆柱体绕流场结构,达到减小圆柱体阻力并抑制其脉动升力之目的,因此是圆柱型结构的一种有效流动控制手段.     

Mechanism of drag reduction by spanwise oscillating Lorentz force in turbulent channel flow

Numerical simulations and experimental research are both carried out to investigate the controlled effect of spanwise oscillating Lorentz force on a turbulent channel flow. The variations of the streaks and the skin friction drag are obtained through the PIV system and the drag measurement system, respectively. The flow field in the near-wall region is shown through direct numerical simulations utilizing spectral method. The experimental results are consistent with the numerical simulation results qualitatively, and both the results indicate that the streaks are tilted into the spanwise direction and the drag reduction utilizing spanwise oscillating Lorentz forces can be realized. The numerical simulation results reveal more detail of the drag reduction mechanism which can be explained, since the spanwise vorticity generated from the interaction between the induced Stokes layer and intrinsic turbulent flow in the near-wall region can make the longitudinal vortices tilt and oscillate, and leads to turbulence suppression and drag reduction.     

Widerstandsverminderung in turbulenten Rohrströmungen: Stabilitätsverhalten wäßriger Polyacrylamidlösungen bei mechanischer und thermischer Beanspruchung

Experimental results on the drag reduction efficiency of polymers based on acrylamide are represented and discussed. The measurements were carried out on a laboratory and a pilot plant scale. Points of main interest are the mechanical and thermal stability of the polymers. The laboratory tests, which were performed under well defined conditions, show the decisive influence of wall shear stress on degradation. These results explain the good stability, which has been measured in a technical pipeline. In the case of suspensions of coal in water a drag reduction efficiency interesting for technical applications has been observed, too. The thermal degradation of the polymer is accelerated by oxygen solved in the water. Under inert conditions only very small degradation effects occur even at temperatures up to 150 °C. GPC measurements give instructive results for an understanding of the thermal and mechanical degradation of the polymers on a molecular base.     

Drag reduction by coupled systems: microbubble injection with homogeneous polymer and surfactant solutions

 The influence of homogeneous surfactant and homogeneous polymer solutions on the performance of microbubble skin friction reduction was investigated on an axisymmetric body. Carbon dioxide was injected into water, homogeneous surfactant (Aerosol OT) solutions, and homogeneous dilute polymer (Polyethylene oxide) solutions. Integrated skin friction measurements were obtained at two freestream velocities as a function of gas injection rate and polyethylene-oxide concentration. A moderate (50%) decrease in surface tension had little to no effect on the drag reducing characteristics of microbubble injection. At similar gas injection rates, microbubble injection exhibited more drag reduction in the polymer solutions than obtained with microbubble injection into water. However, the increased drag reduction obtained with polymer additives was no more than a multiplicative factor related to the baseline levels of drag reduction achieved by the individual methods, and suggests the mechanism for microbubble skin friction reduction acts independently of the polymer drag reduction. Received: 17 April 1998 / Accepted: 12 October 1998     

Prediction of the drag reduction effect of pulsating pipe flow based on machine learning

Prediction of drag reduction effect caused by pulsating pipe flows is examined using machine learning. First, a large set of flow field data is obtained experimentally by measuring turbulent pipe flows with various pulsation patterns. Consequently, more than 7000 waveforms are applied, obtaining a maximum drag reduction rate and maximum energy saving rate of 38.6% and 31.4%, respectively. The results indicate that the pulsating flow effect can be characterized by the pulsation period and pressure gradient during acceleration and deceleration. Subsequently, two machine learning models are tested to predict the drag reduction rate. The results confirm that the machine learning model developed for predicting the time variation of the flow velocity and differential pressure with respect to the pump voltage can accurately predict the nonlinearity of pressure gradients. Therefore, using this model, the drag reduction effect can be estimated with high accuracy.