预应力对LY12铝弹性前驱波的影响

通过过盈配合的热装配方法对LY12铝合金平面样品施加了径向预应力,采用平面飞片撞击方法获得了预应力对弹性前驱波的影响。结果表明:当飞片均以500 m/s的速度撞击样品时,压缩预应变为0(无预应变)、964.5×10-6和1 886.0×10-6时,弹性前驱波幅值分别为87.56、95.24、121.03 m/s,压缩预应力(变)提高了LY12铝弹性前驱波幅值。结合实验的特点,探讨了对样品施加静态径向预应力的数值模拟方法,结果表明,上升沿(100 μs)较为缓慢的加载可以达到与准静态加载应力分布一样的结果。采用该数值模拟方法给出和验证了弹性前驱波随压缩预应力增加而上升的计算结果,与实验结果较为吻合。     

初始应力状态对材料层裂破坏特性影响研究

通过对球面飞片加载条件下的应力/应变状态分析表明采用施加径向应变方法可以近似模拟球面加载的受力过程. 采用过盈配合的热装配方法对平面样品施加了径向预应变,一维平面应变气炮实验结果显示初始预应力(变)明显降低了LY12铝层裂强度. 从空洞长大基本原理出发分析了各向异性受力条件下空洞长大的路径和所消耗能量不同于各向同性应力加载.通过数值模拟对含损伤的材料本构模型进行分析,得到了材料层裂强度与其外部宏观应力场密切相关,也间接的与构型相关的结论.      

复杂应力状态下材料层裂特性探讨

在综述一维平面应变下层裂研究特点和研究方法的基础上,采用实验转换的方法,近似模拟球面层裂的受力特征,获得了不同预应变下LY12铝合金层裂信号,表明材料的层裂强度与所处应力状态密切相关。结合这些研究成果,探讨了复杂应力条件下层裂的新特征,讨论了可能用于层裂研究的方法及其改进措施。     

无氧铜层裂的实验与数值研究

利用一级气体炮对国产的无氧铜（OFHC）进行了平板撞击致层裂实验,3 mm厚的OFHC飞片撞击6 mm厚的OFHC靶,采用锰铜应力计记录试样/有机玻璃（PMMA）界面附近的应力历史,获得试样发生层裂的信息。软回收试样,观测回收试样的层裂片。采用基于空穴聚集的层裂模型,数值模拟这些平板撞击致层裂实验。数值模拟的应力剖面以及试样层裂片厚度与实验结果基本一致。此外,对于国外相关的OFHC层裂实验,采用基于空穴聚集的层裂模型也作了相应的数值模拟,并进行了比较。     

双屈服面法测量金属材料动高压屈服强度的若干改进

在J.R.Asay等提出的双屈服面法（简称AC方法）测量动态屈服强度的基础上,对实验设计和数据处理做了部分改进。在实验设计方面,在满足实验物理设计的前提下,将 AC方法的卸载实验装置(双层飞片和双台阶样品)简化为单飞片和单台阶样品,以简化波系作用,并减少了声速测量不确定度的引入因素。在数据处理方面,发现由Lagrange声速和工程应变关系曲线外推求预冲击态的体积声速容易引入较大的不确定度,而通过Lagrange声速和粒子速度关系曲线可以更清晰地得到塑性卸载起始点,使图解法和积分法得到的屈服强度值趋于一致。利用改进后的AC方法,得到了低温退火后LY12铝在20.0 GPa预冲击压力下的屈服强度为0.6 GPa。     

晶粒尺寸对高纯铝板材层裂特性的影响

采用不同热处理工艺制备了3种晶粒尺寸（60、100、500 μm）的高纯铝板材,利用平板撞击实验研究了其层裂行为。通过改变飞片击靶速度,在靶板中实现初始层裂状态和完全层裂状态。基于自由面速度时程曲线和微损伤演化及断口显微形貌分析,讨论了晶粒尺寸对高纯铝板材层裂特性的影响规律。实验结果显示:（1）晶粒尺寸对高纯铝板材层裂特性的影响强烈依赖于冲击加载应力幅值,在低应力条件下,层裂强度与晶粒尺寸之间表现出反Hall-Petch关系,而在高应力条件下,晶粒尺寸对层裂强度几乎没有影响;（2）随着晶粒尺寸的增大,靶板损伤区微孔洞的尺寸和分布范围均增大,但数量显著减少,在微孔洞周围还发现比较严重的晶粒细化现象;（3）随着晶粒尺寸的增大,层裂微观机制从韧性沿晶断裂向准脆性沿晶断裂转变,且在断口上观察到少量随机分布的小圆球,归因于微孔洞长大和聚集过程中严重塑性变形引起的热效应。     

拉伸应变率对20钢层裂特性的影响

采用轻气炮加载技术和激光速度干涉(VISAR)测速技术相结合,对不同拉伸应变率条件下20钢的层裂特性进行了实验研究。通过改变飞片和样品的几何尺寸来调整拉伸应变率的大小,研究了拉伸应变率对20钢层裂强度的影响。实验的拉伸应变率的变化范围为104~106 s-1,最大拉伸应变率接近激光加载所能产生的拉伸应变率,相比激光加载,薄飞片技术容易保证一维应变条件。实验结果显示20钢的层裂特性明显依赖着拉伸应变率的大小,106 s-1条件下层裂强度比104 s-1时提高近70%。基于对数值计算结果的分析,讨论了影响层裂强度的主要外载荷因素。     

激光选区熔化增材制造GP1不锈钢动态拉伸力学响应与层裂破坏

采用选择性激光熔化增材制造技术,制备了GP1不锈钢单轴拉伸板条试样和层裂圆片试样,并对材料微观结构进行了表征。借助Zwick-HTM5020高速拉伸试验机,并结合数字图像相关性全场应变测量技术,开展了增材制造GP1不锈钢材料的轴向拉伸力学性能实验研究,得到了不同应变率下材料的拉伸应力-应变曲线,结果显示:(1)GP1不锈钢流动应力具有比较显著的应变强化效应;(2)通过回收试样的电子背散射衍射表征,发现GP1不锈钢在拉伸变形过程中会发生奥氏体与马氏体之间的相变;(3)GP1不锈钢的屈服应力随着应变率呈幂指数增大,断裂应变在中低应变率下保持不变,但在高应变率下则显著减小。采用一级轻气炮实验装置和激光干涉粒子速度测量技术,开展了增材制造GP1不锈钢的层裂实验,发现GP1不锈钢的层裂强度随着飞片撞击速度增大而减小。单轴拉伸试样断口和层裂试样断口的显微分析结果表明:随着应变率增大,单轴拉伸断裂模式和断裂机理都发生了转变;层裂损伤易成核于激光熔池边界线的交汇处,断口韧窝形貌明显区别于单向拉伸断口。     

磁驱动准等熵压缩下LY12铝的强度测量

高压高应变率加载下材料的强度研究一直是冲击动力学的一个难题,目前动态载荷下材料的高压强度测量主要是基于平板撞击技术,冲击温升和应变率效应对材料强度的影响难以分离. 基于小型磁驱动加载装置CQ-4,开展了磁驱动准等熵压缩下LY12 铝的声速和强度测量的实验研究,讨论了考虑加载-卸载过程时磁驱动压缩实验的负载电极设计、实验样品设计、数据处理与分析等内容,并获得了12 GPa 压力范围沿加载-卸载路径的声速变化和峰值压力点的强度数据.      

基于“钉床型”飞片的斜波加载技术及应用

为了实现斜波加载,设计了一种“钉床型”广义波阻抗梯度飞片,即在基座上密排叠加许多小圆锥,简称“钉床型”飞片。该飞片采用激光选区熔化金属增材制造技术进行制备。利用一级轻气炮加载装置和全光纤激光位移干涉测试系统,开展不同工况下“钉床型”飞片高速击靶压缩实验和层裂实验,重点讨论小圆锥高度和撞击速度对斜波压缩加载波形的影响规律,以及斜波加载对不锈钢靶板层裂特性的影响。实验结果显示:（1）“钉床型”飞片对靶板产生的压缩是逐步的,从自由面速度剖面上观察到压缩波上升前沿时间被显著延长,形成了斜波波阵面,明显不同于冲击压缩的陡峭波阵面;（2）在飞片击靶速度近似恒定条件下,斜波波阵面的上升沿时间、平台速度峰值都明显依赖于“钉床型”飞片上的小圆锥高度,随着小圆锥高度增大,上升沿时间呈线性增大,而平台速度峰值呈线性减小;（3）在“钉床型”飞片的几何尺寸保持不变的条件下,斜波波阵面的上升沿时间随着飞片击靶速度的增大而线性减小,平台速度峰值则线性增大;（4）与冲击加载相比,“钉床型”飞片产生的斜波加载不会对材料的层裂强度产生明显影响,但对材料内部损伤演化速率有一定的影响。     

Anomaly in the dynamic strength of austenitic stainless steel 12Cr19Ni10Ti under shock wave loading

Measurement results for the shock wave compression profiles of 12Cr19Ni10Ti steel and its dynamic strength in the strain rate range 10⁵–10⁶ s^?1 are presented. The protracted viscous character of the spall fracture is revealed. With the previously obtained data taken into account, the measurement results are described by a polynomial relation, which can be used to construct the fracture kinetics. On the lower boundary of the range, the resistance to spall fracture is close to the value of the true strength of the material under standard low-rate strain conditions; on the upper boundary, the spall strength is more than twice greater than this quantity. An increase in the temperature results in a decrease in both the dynamic limit of elasticity and the spall fracture strength of steel. The most interesting result is the anomaly in the dependence of the spall fracture strength on the duration of the shock wave compression pulse, which is related to the formation of deformation martensite near the growing discontinuities.     

强角闪石化橄榄二辉岩的动态拉伸强度实验研究

对强角闪石化橄榄二辉岩的动态拉伸断裂强度进行了实验研究。设计了能在样品中产生持续时间大约为1.5 s拉伸应力脉冲的平板冲击回收实验。通过对回收样品的宏观和微观观察,确定了样品出现拉伸破坏开始阶段以及破坏裂纹的扩展阶段,进而确定了该岩石样品的动态拉伸强度约为265.6~315.3 MPa。同时,基于线弹性近似,导出了在一维应变条件下样品内拉伸应力和作用时间的估算公式。     

三角形波致LY12铝层裂的平板冲击实验研究

采用基于冲击波衰减动力学的实验技术,使平板碰撞层裂实验的LY12铝样品中,产生三角形冲击脉冲.采用VISAR技术记录样品自由表面历史,获得样品中发生层裂的信号.在经过高应力三角形波实验的软回收样品上,发现了两个层裂面.就样品中呈现三角形脉冲的平板冲击实验而言,样品中可以存在一些高拉伸应力区域并发生多次层裂.将该文提出的基于空穴聚集的层裂模型用于数值模拟这些特定条件的平板冲击试验,并将计算的样品自由面速度历史及样品中的损伤分布与实测的VISAR数据及软回收的样品层裂面等作了比较.研究表明,人为粘性、状态方程、本构方程以及层裂模型对于数值模拟三角形冲击脉冲引起的层裂有严重影响.     

Spall strength of glass fiber reinforced polymer composites

In the present paper results of a series of plate impact experiments designed to study spall strength in glass–fiber reinforced polymer composites (GRP) are presented. Two GRP architectures are investigated—S2 glass woven roving in Cycom 4102 polyester resin matrix and a balanced 5-harness satin weave E-glass in a Ciba epoxy (LY564) matrix. The GRP specimens were shock loaded using an 82.5 mm bore single-stage gas-gun. A velocity interferometer was used to measure the particle velocity profile at the rear (free) surface of the target plate. The spall strength of the GRP was obtained as a function of the normal component of the impact stress and the applied shear-strain by subjecting the GRP specimens to normal shock compression and combined shock compression and shear loading, respectively. The spall strengths of the two GRP composites were observed to decrease with increasing levels of normal shock compression. Moreover, superposition of shear-strain on the normal shock compression was found to be highly detrimental to the spall strength. The E-glass reinforced GRP composite was found to have a much higher level of spall strength under both normal shock compression and combined compression and shear loading when compared to the S2-glass GRP composite. The maximum spall strength of the E-glass GRP composite was found to be 119.5 MPa, while the maximum spall strength for the S2 glass GRP composite was only 53.7 MPa. These relatively low spall strength levels of the S2-glass and the E-glass fiber reinforced composites have important implications to the design and development of GRP-based light-weight integral armor.     

Spall Characterization in Epoxy Via Laser Spallation

Background: The strength of materials under extreme dynamic loading conditions, such as in the case of shock wave loading, is assessed from their spallation characteristics. Under laboratory conditions, flyer plate impact, or sometimes laser-induced stress waves, is employed to instigate spall in a material. These methods are often combined with velocity interferometer system for any reflector (VISAR) technique for performing transient measurements. Although the VISAR can record the velocity of extremely fast-moving surfaces, it requires a complex optical setup and a specialized data reduction technique. Objective: In this study, a simpler approach is adopted by extending laser spallation method to determine the spall strength of epoxy, while performing in situ interferometric measurements, directly on top of thick epoxy films. Methods: The glass/epoxy test samples are prepared by transferring an aluminum coating on top of epoxy layers with different thicknesses. Laser-induced stress waves transmit across the substrate/film interface and induce subsurface failure in the epoxy at sufficiently high incident laser energy. The nature and magnitude of the waves are deciphered from the out-of-plane displacement histories of the top reflective sample surfaces, which are recorded by using a Michelson interferometer. Results: The interferometric data reveal the development of two (temporally) well-separated stress waves: an ablation-induced high-amplitude short-duration longitudinal pulse, which is referred to as the primary wave, and a secondary wave, which travels at a comparatively slower speed. The complex constructive interaction of the two waves develops a high-magnitude tensile stress region in the epoxy layer. The spall strength is quantified by superimposing the two stress wave histories associated with the critical energy fluence. Conclusions: The spall depths predicted from spatiotemporal wave travel analyses are in excellent agreement with the experimental observations. The newly adopted methodology estimates the spall strength of epoxy as 260?±?20 MPa.