Mechanical properties of plasma‐treated carbon fiber reinforced PTFE composites with CNT

This paper is concerned with the effects of the plasma surface treatment and the addition of CNT on the mechanical properties of carbon fiber/polytetrafluoroethylene (PTFE) composite. The tensile and flexural strength of composites containing CNT and plasma‐treated carbon fibers improved. The flexural strength first decreases with respect to the CF content. The flexural strength increases to 179 MPa for the plasma‐treated composite as compared with 167 MPa for the neat carbon fiber composites. The overall improvement is thus nearly 8%.     

The influence of surface treatment on the tensile and tribological properties of wood fiber‐reinforced polyimide composite

In this paper, the effect of coupling agent surface treatment of wood fiber on tensile and tribological property of wood fiber‐reinforced thermoplastic polyimide (PI) composites was experimentally investigated. Experimental results revealed that coupling agent surface treatment could effectively improve the interfacial adhesion between wood fiber and PI matrix. Compared with the untreated wood fiber/PI composite, the coupling agent‐treated composite had better interfacial adhesion. The fracture surfaces and worn surface of samples were investigated by scanning electronic microscopy to analyze the effects of surface treatment methods.     

Effect of solid lubricant particles on the tribological properties of PTFE composites lubricated with natural seawater

An orthogonal test was used to design different mixture ratios of molybdenum disulfide(MoS₂), graphite, and SiO₂ particles, which were filled with polytetrafluoroethylene (PTFE) composite. MoS₂-, graphite-, and SiO₂-modified PTFE was obtained by pressing and sintering, and the processing parameters were determined using progressive studies and experiments. The friction and wear properties of different PTFE composites lubricated with natural seawater were analyzed using an MMU-5G wear tester. A laser scanning confocal microscope was employed to examine the morphological characteristics of the worn surface. Moreover, the influence of particle proportions on the tribological property of composites was analyzed. Results show that the addition of SiO₂, MoS₂, and graphite can increase the bearing capacity, improve the wear resistance, reduce the friction coefficient, and increase the self-lubricating ability of the PTFE matrix.     

Structure and tribological properties of Cu–PU–PTFE composite coatings prepared by low‐energy electron beam dispersion with glow discharge

Polytetrafluoroethylene (PTFE) composite coatings doped copper acetate and polyurethane (PU) were prepared on rubber substrate by low‐energy electron beam dispersion technique. The effects of dopant and glow discharge treatment on the surface morphology, structure and tribological properties of the coatings were investigated. The results showed that Cu–PTFE composite coatings form uniform surface and dense column structure with spherical aggregations under glow discharge treatment. PU coating shows the large size of protuberance structure but PU–PTFE coating presents spherical structure. Both of the coatings become relative dense and smooth after discharge treatment, and Cu–PU–PTFE composite coatings possess a smoother surface and lower polar component of surface energy. Cu doping weakens the crystallinity and ordering degree of composite coatings, but glow discharge increases the ordering degree and branched structure of C―H groups. Friction experiment indicated that Cu fails to improve the wear resistance of PTFE coatings but glow discharge treatment can do it. Cu–PU–PTFE coatings after discharge treatment have the higher wear resistance and lower coefficient of friction. Copyright © 2016 John Wiley & Sons, Ltd.     

Improvement of interfacial adhesion for plasma‐treated aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) composite and fiber surface aging effects

Interfacial adhesion between the fiber and the matrix in a composite is a primary factor for stress transfer from the matrix to the fiber. In this study, oxygen plasma treatment method was applied to modify the fiber surface for improving interfacial adhesion of aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite. Composite interfacial adhesion properties were determined by interlaminar shear strength (ILSS) using a short‐beam bending test. The composite interfacial adhesion mechanism was discussed by SEM. The changes of chemical composition and wettability for plasma‐treated fiber surfaces stored in air as long as 10 days were investigated by XPS and dynamic contact angle analysis (DCAA), respectively. Results indicated that oxygen plasma treatment was an effective method for improving interfacial adhesion; plasma‐treated fiber surface suffered aging effects during storage in air. Copyright © 2008 John Wiley & Sons, Ltd.     

The tribological performance of fullerene‐like hydrogenated carbon films under ionic liquid lubrication

Fullerene‐like hydrogenated carbon films were deposited on Si substrate by plasma‐enhanced chemical vapor deposition. The microstructures of films were characterized by high‐resolution transmission electron microscopy and Raman spectrum. The tribological performance of films was tested by reciprocating ball‐on‐disc tester under 1‐ethyl‐3‐methylimidazolium tetrafluoroborate ionic liquid. The surface morphology and chemical composition of wear tracks and wear rates were investigated by optical microscope, X‐ray photoelectron spectroscopy, and 3D surface profiler. The results indicated that the film with a typical fullerene‐like structure embedded into the amorphous sp² and sp³ carbon networks could be prepared successfully, and the film shows a higher hardness (26.7 GPa) and elastic recovery (89.9%) compared with the amorphous carbon film. Furthermore, the film shows a lower friction coefficient at low contact load and friction frequency, and excellent wear‐resistance performance at high load and frequency under ionic liquid lubrication. Meanwhile, the wear life of fullerene‐like hydrogenated carbon films could be improved significantly using ionic liquid as a lubrication material. Copyright © 2015 John Wiley & Sons, Ltd.     

The effect of surface modification with nitric acid on the mechanical and tribological properties of carbon fiber‐reinforced thermoplastic polyimide composite

Polyacrylamideacrylate (PAN)‐based carbon fibers were submitted to nitric acid oxidation treatments to improve the interfacial adhesion of the carbon fiber (CF)‐reinforced polyimide (CF/PI) composite. The carbon fiber surfaces were characterized by X‐ray photoelectron spectroscopy (XPS). Nitric acid oxidation not only affects the oxygen concentration but also produces an appreciable change in the nature of the chemical functions, namely the conversion of hydroxy‐type oxygen into carboxyl functions. Nitric acid oxidation treatment modifies the element constituting the fiber, the nitrogen concentration being about 1.2 times higher at the fiber external surface compared to the untreated one. The mechanical and tribological properties of the polymide (PI) composites reinforced by the carbon fibers treated with nitric acid oxidation were investigated. Results showed that the tensile strength of the CF/PI composites improved remarkably due to nitric acid treatment along with enhancement in friction and wear performance. Copyright © 2009 John Wiley & Sons, Ltd.     

The flexural and tribological properties of UHMWPE composite filled with plasma surface‐treated wood fibers

In this paper, the wear performance of an ultra‐high molecular weight polyethylene composites filled with wood fiber were studied using a pin‐on‐disc method. The effects of surface treatment of wood fiber and sliding load and on the friction and wear of the wood fiber/UHMWPE composite are reported. The test results showed that the sliding load is an important controlling factor; its effect is diminished when the wood fiber is modified.     

Improved mechanical properties of epoxy composites reinforced with surface‐treated UHMWPE fibers

The surface treatment of ultra‐high molecular weight polyethylene fiber using potassium permanganate and the mechanical properties of its epoxy composites were studied. After treatment, many changes were happened in the fiber surface: more O‐containing groups (―OH, ―C═O, and ―C―O groups), drastically decreased contact angles with water and ethylene glycol, slightly increased melting point and crystallinity, and formed cracks. Different contents (0.1–0.5 wt%) ultra‐high molecular weight polyethylene fibers/epoxy composites were prepared. The results indicated that the surface treatment decreased the tensile strength of epoxy composites, but increased the bending strength. When the fiber content was 0.3 wt%, the above properties reached the maximum. At the same fiber content, the interlaminar shear strength of the composites was increased by 26.6% up to the as‐received fiber composites. Dynamic mechanical analysis of the composites suggested the storage modulus and tanδ were decreased due to the surface treatment. Fractured surface analysis confirmed that the potassium permanganate treatment was effective in improving the interface interaction.     

The interlaminar shear strength and tribological properties of PA 6 composites filled with graphene oxide‐treated carbon fiber

The objective of this work is to improve the interlaminar shear strength and tribological properties of the PA 6 composites by graphene oxide‐treated carbon fiber (CF) and ultraviolet irradiation of PA 6. The morphologies of untreated and treated CFs were characterized by X‐ray photoelectron spectroscopy. Surface analysis showed that after treatment, the surface of CFs chemisorbed oxygen‐containing groups; active carbon atom, the surface roughness, and wetting ability were increased. The results show that the treated CF composites can possess excellent interfacial properties and tribological properties accordingly after treatment. Copyright © 2017 John Wiley & Sons, Ltd.     

Effect of carbon fiber surface treatments on the flexural strength and tribological properties of short carbon fiber/polyimide composites

Pitch‐based short carbon fibers (CFs) were treated by air oxidation and cryogenic nitrogen, respectively. Thereafter the treated and untreated CFs were incorporated into polyimide (PI) matrix to form composites. The CFs before and after treatment were examined by XPS and SEM.The flexural strength of the specimen was determined in a three‐point test machine and the tribological properties of PI composites sliding against GCr15 steel rings were evaluated on an M‐2000 model ring‐on‐block test rig. The results show that the surface of the treated CFs became rougher. Lots of active groups formed on the CF surface after air oxidation.The treatment can effectively improve the mechanical and tribological properties in their PI composites due to the enhanced fiber‐matrix interfacial bonding. Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of fabric geometry on yarn pull‐out property and wear performance of hybrid S‐glass/PTFE fabric‐reinforced composites

The friction states between yarns affect the stress transferred in fabric and the fabric structure significantly affects the tribological properties of composites. In this aricle, the effects of fabric structure on yarn pull‐out property and tribological performance of composite were thoroughly studied. Four different fabrics with same tissue cycles number and thread count (2/2 double twills, 1/3 twill, 4‐shaft satin, and 4‐shaft reinforced satin) were used to evaluate the yarn pull‐out property in fabric and the tribological performance of corresponding composites. The results indicate that fabric structure has a significant effect on the yarn pull‐out property in fabric. In particular, the yarn pull‐out property of 4‐shaft reinforced satin was best in the four fabrics structure used in this article owing to the excellent integrity of the 4‐shaft reinforced satin fabric structure and the distribution characteristics of the fabric intersection points. The tribological performance of the 4‐shaft reinforced satin fabric enhanced composites were positively correlated with yarn pull‐out property because the yarn pull‐out property in fabric played an important role in energy dissipation and load carry capacity.     

Effects of UV irradiation on tribological properties of nano‐TiO2 thin films

One‐layer and two‐layer nano‐TiO₂ thin films were prepared on the surface of common glass by sol–gel processing. Water contact angle, surface morphology, tribological properties of the films before and after ultraviolet (UV) irradiation were investigated using DSA100 drop shape analyzer, scanning probe microscopy (SPM), SEM and universal micro‐materials tester (second generation) (UMT‐2MT) friction and wear tester, respectively. The stored films markedly resumed their hydrophilicity after UV irradiation. But UV irradiation worsened tribological properties of the films. After the film was irradiated by UV, the friction coefficient between the film and GCr15 steel ball increased about 10–50% and its wear life shortened about 20–90%. Abrasive wear, brittle break and adherence wear are the failure mechanisms of nano‐TiO₂ thin films. It was believed that UV irradiation increased surface energy of the film and then aggravated adherence wear of the film at initial stage of friction process leading to severe brittle fracture and abrasive wear. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation and properties of silylated PTFE/SiO2 organic–inorganic hybrids via sol–gel process

A study on poly(tetrafluoroethylene) (PTFE) reinforced with tetraethoxysilanes (TEOS) derived SiO₂ is described. It included the manufacturing process of SiO₂‐reinforced PTFE and the effects of silylation agent on the properties of the hybrid material, such as porosity, hydrophobic, thermal resistance, dielectric and mechanical properties, and microstructure. PTFE/SiO₂ hybrids of 50 wt % SiO₂ loading were prepared via a sol–gel process and were shaped by a two‐roll milling machine. Trimethylchlorosilane and hexamethydisilazane were used as the silylation agents. Our results showed that the water absorption and dielectric loss of PTFE/SiO₂ hybrid had significantly improved with silylation agent. The silylation process replaced Si? OH with Si? CH₃ on the surface of the TEOS‐derived silica colloidal particle. The existence of trimethylsilyl [? Si(CH₃)₃] on the surface of the modified PTFE/SiO₂ hybrid was confirmed via infrared and solid‐state ²⁹Si magic‐angle spinning nuclear magnetic resonance spectra. Nitrogen‐sorption techniques were used to characterize the modified and unmodified PTFE/SiO₂ hybrids. The microstructure of SiO₂ in the matrix was also evaluated with scanning electron microscopy and transmission electron microscopy. Our results showed that the silylated sol–gel‐derived PTFE/SiO₂ hybrids had exhibited high porosity (53.7%) with nanosize pores (10–40 nm) and nanosize colloidal particles (20–50 nm). This manifests itself as have the ultralow dielectric properties (D_k = 1.9 and D_f = 0.0021), low coefficient of thermal expansion (66.5 ppm/°C), high tensile modulus (141 MPa), excellent thermal resistance (T_d = 612 °C), and an increased hydrophobia (θ = 114°); moreover, the hydrophobic property of the PTFE/SiO₂ hybrid was thermally stable up to 400 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1789–1807, 2004     

Effect of surface‐grafted ionic groups on the performance of cellulose‐fiber‐reinforced thermoplastic composites

The influence of the surface chemistry of the cellulose fiber and polymer matrix on the mechanical and thermal dynamic mechanical properties of cellulose‐fiber‐reinforced polymer composites was investigated. The cellulose fiber was treated either with a coupling agent or with a coupling‐agent treatment followed by the introduction of quaternary ammonium groups onto the fiber surface, whereas the polymer matrix, with opposite polar groups such as polystyrene incorporated with sulfonated polystyrene and poly(ethylene‐co‐methacrylic acid), was compounded with the fiber. The grafting of the fiber surface was investigated with Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy. Experimental results showed that an obvious improvement in the mechanical strength could be achieved for composites with an ionic interface between the fiber and the polymer matrix because of the adhesion enhancement of the fiber and the matrix. The improved adhesion could be ascribed to the grafted ionic groups at the cellulose‐fiber surface. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2022–2032, 2003     

Comparative study of the effects of nano‐sized and micro‐sized CF and PTFE on the thermal and tribological properties of PEEK composites

The tribological characteristics of PEEK composites fretting against GCr 15 steel were investigated by a SRV‐IV oscillating reciprocating ball‐on‐disk tribometer. In order to clarify the effect of type and size of fillers on the properties of PEEK composites, nano‐sized and micro‐sized CF and PTFE fillers were added to the PEEK matrix. The thermal conductivity, hardness, and fretting wear properties of PEEK composites reinforced by CF or PTFE were comparatively studied. The results showed that the type and size of the fillers have an important effect on both the friction coefficient and wear rate, by affecting their thermal conductivity, hardness, as well as the surface areas of their transfer films. In comparison, the effect on improving the tribological properties of micro‐sized CF was superior to that of nano‐sized CF, while the effect of nano‐sized PTFE was superior to that of micro‐sized PTFE. Considering the acceptable friction coefficient and wear rate of the composite under the fretting wear test, it seemed that 4% nCF, 20% mCF, 2% nPTFE and 10% mPTFE were desired additive proportions. And it also can be found that during the fretting wear test, the abrasive and adhesive wear resulted in accumulative debris at the contacting surface. The transfer films made of debris were formed on the counterfaces.     

Effect of fiber length and composition on mechanical properties of carbon fiber‐reinforced polybenzoxazine

The mechanical strength and modulus of chopped carbon fiber (CF)‐reinforced polybenzoxazine composites were investigated by changing the length of CFs. Tensile, compressive, and flexural properties were investigated. The void content was found to be higher for the short fiber composites. With increase in fiber length, tensile strength increased and optimized at around 17 mm fiber length whereas compressive strength exhibited a continuous diminution. The flexural strength too increased with fiber length and optimized at around 17 mm fiber length. The increase in strength of composites with fiber length is attributed to the enhancement in effective contact area of fibers with the matrix. The experimental results showed that there was about 350% increase in flexural strength and 470% increase in tensile strength of the composites with respect to the neat polybenzoxazine, while, compressive properties were adversely affected. The composites exhibited an optimum increase of about 800% in flexural modulus and 200% in tensile modulus. Enhancing the fiber length, leads to fiber entanglement in the composites, resulted in increased plastic deformation at higher strain. Multiple branch matrix shear, debonded fibers and voids were the failures visualized in the microscopic analyses. Defibrillation has been exhibited by all composites irrespective of fiber length. Fiber debonding and breaking were associated with short fibers whereas clustering and defibrillation were the major failure modes in long fiber composites. Increasing fiber loading improved the tensile and flexural properties until 50–60 wt% of fiber whereas the compressive property consistently decreased on fiber loading. Copyright © 2008 John Wiley & Sons, Ltd.     

The influence of Ti plasma etching pre-treatment on mechanical properties of DLC film on cemented carbide

The pre-treatment of substrate surface had been a key part of DLC film preparation to improve mechanical and tribological properties. Ti plasma etching pre-treatment was investigated in this paper as a new effective surface pre-treatment method to substitute transition layer. This pre-treatment used high-energy Ti plasma to impact substrate surface. Ti plasma etched the substrate to a depth of 407 nm and increased the roughness from 1.36 to 40.39 nm. A trace layer of substrate, together with cobalt, oxides, and other impurities, was removed. Ti plasma broke some top WC crystals and combined with the free carbon ions separating from the substrate. A DLC film was deposited on the etched surface. Compared with DLC films deposited on the untreated substrate and Ti transition layer, the DLC film on the Ti plasma etched substrate had best adhesion strength of 34.14 N. The three DLC films had the same sp³ bonding carbon content, but Ti plasma etching treatment could promote the formation of sp³ bonds on the interface of substrate and DLC film. This DLC film had low friction coefficient of 0.12 and low wear rate of 5.11 × 10⁻⁷ mm³/m·N. In summary, Ti plasma etching pre-treatment could significantly improve the adhesion of DLC film and keep its excellent tribological properties.     

The mechanical properties of plasma‐treated carbon fiber reinforced PA6 composites with CNT

The aim of this work is the evaluation of the effects of plasma treatment and the addition of CNT on the mechanical properties of carbon fibre/PA6 composite. A powder impregnation process with integrated inline continuous plasma of carbon fibers was used to produce CF/PA6 composite. CF/PA6 composite was processed into test laminates by compression moulding, and interface dominated composite properties were studied. The tensile and impact strength of composites containing CNT and plasma‐treated carbon fibres improved obviously. The tensile strength of nanocomposite largely increases with the increasing of the CNT content and then decreases when the CNT content is over 2%. The hydroxyl groups of the fibers surface are in favor of the wettability of carbon fibers by the polar matrix resin, which is resulting in a further interaction of the fiber surface with the curing system of the matrix resin.