Structural,chemical and nanomechanical investigations of SiC/polymeric a-C:H films deposited by reactive RF unbalanced magnetron sputtering

Amorphous carbon (or diamond-like carbon, DLC) films have shown a number of important properties usable for a wide range of applications for very thin coatings with low friction and good wear resistance. DLC films alloyed with (semi-)metals show some improved properties and can be deposited by various methods. Among those, the widely used magnetron sputtering of carbon targets is known to increase the number of defects in the films. Therefore, in this paper an alternative approach of depositing silicon-carbide-containing polymeric hydrogenated DLC films using unbalanced magnetron sputtering was investigated. The influence of the C₂H₂ precursor concentration in the deposition chamber on the chemical and structural properties of the deposited films was investigated by Raman spectroscopy, X-ray photoelectron spectroscopy and elastic recoil detection analysis. Roughness, mechanical properties and scratch response of the films were evaluated with the help of atomic force microscopy and nanoindentation. The Raman spectra revealed a strong correlation of the film structure with the C₂H₂ concentration during deposition. A higher C₂H₂ flow rate results in an increase in SiC content and decrease in hydrogen content in the film. This in turn increases hardness and elastic modulus and decreases the ratio H/E and H³/E². The highest scratch resistance is exhibited by the film with the highest hardness, and the film having the highest overall sp³ bond content shows the highest elastic recovery during scratching.     

Effect of nitrogen on mechanical,oxidation and structural behaviour of Ti–Si–B–C–N nanocomposite hard coatings deposited by DC sputtering

Ti–Si–B–C–N film was deposited by DC magnetron sputtering at different argon and nitrogen ratios such as N₂/Ar = 1 : 5, 2 : 4, 3 : 3, 4 : 1 and 5 : 0. The formation of TiN and TiB phases was observed because of incorporation of nitrogen. The hardness, modulus, microstructure, structure and bond formation with different nitrogen contents during the deposition were studied by nanoindentation, scanning electron microscope, X‐ray diffraction and X‐ray photoelectron spectroscopy, respectively. The oxidation kinetics of Ti–Si–B–C–N was investigated. The nitrogen incorporation during deposition influences different properties of the coating. Hardness and modulus decreased, and microstructure showed very fine grain presence, and film changes to fully amorphous because of incorporation of nitrogen in the film. Copyright © 2016 John Wiley & Sons, Ltd.     

The chemical composition and bonding structure of amorphous hydrogenated carbon nitride film on aluminum surface deposited by electrodeposition

Amorphous hydrogenated carbon nitride films with excellent adhesion to the substrates were deposited on the surfaces of aluminum plates by electrodeposition with acetonitrile as carbon source. The as‐obtained films were detailed characterized by Raman, XPS and FTIR. The results show that the as‐obtained films are mainly made up of sp2 C, sp3 C, C? N, C?N bonds and a spot of sp3? CH₂, sp3? CH₃, sp3? CH and sp2? CH bonds. The atomic ratio of N/C is evaluated to be about 2.98 at.% by XPS. Raman analysis indicated that I_D/I_G ratios decreased from 0.827 to 0.675 when the deposition time increased from 10 to 20 h. At the end, on the basis of the detailed analysis, results of Raman, FTIR and XPS, the possible deposition mechanism was discussed. Copyright © 2010 John Wiley & Sons, Ltd.     

Effects of bias voltage on structure and properties of TiAl‐doped a‐C:H films prepared by magnetron sputtering

Hydrogenated TiAl‐doped a‐C:H films were deposited on Si substrates by middle frequency magnetron sputtering TiAl target in argon and methane gas mixture atmosphere. Effects of substrate bias voltage on structure and properties of the films, such as the surface morphology, hardness, chemical nature and bond types, were investigated by means of atomic force microscopy (AFM), XPS, Raman spectroscopy and nanoindentation. The friction and wear behaviors of the deposited films were characterized on an UMT‐2MT tribometer. SEM was utilized to analyze the wear scar on steel balls and debris after sliding on the deposited films under dry friction conditions. The results demonstrated that the film deposited at ? 100 V exhibited low friction coefficient which is attributed to the easier formation of graphitized transfer layer. Copyright © 2010 John Wiley & Sons, Ltd.     

Interaction of N-(aryl)picolinamides with iridium. N–H and C–H bond activations

Reaction of N-(4-R-phenyl)picolinamide (R = OCH₃, CH₃, H, Cl and NO₂) with [Ir(PPh₃)₃Cl] in refluxing ethanol in the presence of a base (NEt₃) affords two yellow complexes (1-R and 2-R). The 1-R complexes contain an amide ligand coordinated to the metal center as a monoanionic bidentate N,N donor along with two triphenylphosphines, a chloride and a hydride. The 2-R complexes contain an amide ligand coordinated to the metal center as a monoanionic bidentate N,N donor along with two triphenylphosphines and two hydrides. Similar reaction of N-(naphthyl)picolinamide with [Ir(PPh₃)₃Cl] affords two organometallic complexes, 3 and 4. In complex 3 the amide ligand is coordinated to the metal center, via C–H activation of the naphthyl ring at the 8-position, as a dianionic tridentate N,N,C donor, along with two triphenylphosphines and one chloride. Complex 4 is similar to complex 3, except a hydride is bonded to iridium instead of the chloride. Structures of the 1-OCH₃, 2-Cl and 4 complexes have been determined by X-ray crystallography. All the complexes are diamagnetic, and show characteristic ¹H NMR signals and intense MLCT transitions in the visible region. Cyclic voltammetry on all the complexes shows a Ir^III–Ir^IV oxidation within 0.50–1.16 V vs. SCE and a reduction of the coordinated amide ligand within −1.02 to −1.25 V vs. SCE.     

Surface characterization of CuSn thin films deposited by RF co‐sputtering method

CuSn thin films were deposited by the radio‐frequency (RF) magnetron co‐sputtering method on Si(100) with Cu and Sn metal targets with various RF powers. The thickness of the films was fixed at 200 ± 10 nm. The synthesized CuSn thin films mainly consisted of Cu₂₀Sn₆ and Cu₃₉Sn₁₁ phases, which was revealed by an X‐ray diffraction (XRD) study. The high‐resolution Cu 2p XPS and Cu LMM Auger electron spectra indicate that metallic Cu oxidized to Cu⁺ and Cu²⁺ as the RF power on Cu target increased. The atomic ratios of Sn⁰ and Sn⁴⁺ decreased, while that of Sn²⁺ increased with increasing RF power on the Cu target. The polar surface free energy (SFE) component has a different tendency in comparison with the total SFE and the dispersive SFE component. The dispersive SFE component was the dominating contributing factor to the total SFE compared with the polar SFE. Copyright © 2016 John Wiley & Sons, Ltd.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

Copper‐Catalyzed Direct Sulfoximination of Heteroaromatic N‐Oxides by Dual C−H/N−H Dehydrogenative Cross‐Coupling

A dual C?H/N?H dehydrogenative coupling of quinoline‐type N‐oxides with sulfoximines that leads to N‐(hetero)arylsulfoximines in high yields has been realized by using a catalytic amount of CuBr in air. The method does not require any additional ligand, base, reactivity modifier or oxidant and provides a practical route towards a series of sulfoximidoyl‐functionalized quinolines and derivatives.     

Preparation of Si–C–N–Fe magnetic ceramics from iron‐containing polysilazane

A new type of hyperbranched polysilazane containing iron (PSZI) compound was synthesized by the polycondensation of silazane lithium salts with FeCl₃, and the structure of the PSZIs was investigated by IR, NMR and elemental analyses. The PSZIs were pyrolyzed under nitrogen, argon or NH₃, and magnetic ceramics could be obtained. The ceramic yields of the PSZIs were higher than those of their corresponding silazanes, and the PSZIs or silazanes with reactive groups containing Si? H, ? CH?CH₂ or higher branched structures had higher yields. The magnetism of the ceramics could be controlled by a pyrolytic atmosphere and temperature: the saturation magnetization M_s ranged from 20 to 100 emu g^?1 and coercivity H_c ranged from 463 to 50 Oe. The transformation of the magnetic loop of the PSZIs pyrolyzed at different temperatures under NH₃ was quite different from those under nitrogen. It was shown by X‐ray diffraction measurements that the magnetic crystalline form could exist as Fe₄N, Fe(0) or Fe₃N depending on temperature under NH₃, but under a nitrogen atmosphere Fe(0) was nearly the only magnetic crystalline form from 600 to 1100 °C. By dipping or spin‐coating of the PSZI solution, then through pyrolysis under nitrogen, argon or NH₃, thin uniform magnetic ceramic films could be fabricated on the substrates. Copyright © 2003 John Wiley & Sons, Ltd.     

Chemical and thermal stability of N‐heterocyclic ionic liquids in catalytic C–H activation reactions

¹H‐NMR spectrum analyses are applied to study the chemical and thermal stability of selected N‐heterocyclic ionic liquids within the reaction system that can highly efficiently activate a C–H bond of methane and convert it into the C–O bond in methanol. Our results indicate that under such reaction conditions involving using a powerful Pt‐based catalyst and strong acidic solvent, the aromatic ring of an imidazolium cation becomes unstable generating an ammonium ion (NH₄⁺). Our results also suggest that the instability of the imidazolium ring is more chemically (participation in reactions) than thermally based. Modifications of the aromatic ring structure such as pyrazolium and triazolium cations can increase the chemical/thermal stability of ionic liquids under these reaction conditions. Copyright © 2014 John Wiley & Sons, Ltd.     

The structure and tribological properties of aluminum/carbon nanocomposite thin films synthesized by reactive magnetron sputtering

Hydrogenated nanocomposite aluminum/carbon thin films (Al/a‐C:H) were fabricated on stainless steel and silicon wafer substrates via unbalanced reactive magnetron sputtering from an Al target in CH₄/Ar plasma. The composition and structure of Al/a‐C:H films were investigated by high‐resolution transmission electron microscope (HRTEM), XPS and micro‐Raman spectroscopy. Nanoindenter, interferometer and ball‐on‐disc tribometer were carried out to evaluate the hardness, internal stress and tribological properties of Al/a‐C:H films. HRTEM observations confirmed that the metallic Al nanocrystallites were uniformly dispersed in the amorphous carbon matrix. XPS and Raman analyses indicated that the sp² content increased with the increase of Al content in the films. Nanoindenter and interferometer tests exhibited that the uniform incorporation of Al nanocrystallites can diminish drastically the magnitude of internal stress with maintaining the higher hardness of as‐deposited films. Especially, the ball‐on‐disc tribometer measurements revealed that the nanocomposite film with 2.3 at.% Al content exhibited relatively better wear resistance and self‐lubrication performance with a friction coefficient of 0.06 and wear rate of 3.1 × 10^?16 m³/ N·m under ambient air, which can be attributed to the relatively higher hardness, the formation of continuous graphitized transfer film on counterface and the reduced reaction of oxygen with carbon. Copyright © 2010 John Wiley & Sons, Ltd.     

Nickel‐Catalyzed Oxidative C−H/N−H Isocyanide Insertion: An Efficient Synthesis of Iminoisoindolinone Derivatives

Transition metal‐catalyzed isocyanide insertion has served as a fundamental and important chemical transformation. Classical isocyanide insertion usually occurs between organohalides and nucleophiles, which normally involves tedious and non‐atom‐economical prefunctionalization processes. However, oxidative C?H/N?H isocyanide insertion offers an efficient and green alternative. Herein, a nickel‐catayzed oxidative C?H/N?H isocyanide insertion of aminoquinoline benzamides has been developed. Different kinds of iminoisoindolinone derivatives could be synthesized in good yields by utilizing Ni(acac)₂ as the catalyst. In this transformation, isocyanide serves as an efficient C1 connector, which further inserted into two simple nucleophiles (C?H/N?H), representing an effective way to construct heterocycles.     

Electrochemical Oxidative C−H/N−H Coupling between γ‐Lactams and Anilines

A mild method for the direct C?H/N?H coupling between γ‐lactams and anilines through electrochemical oxidation has been developed. The protocol proceeded smoothly without metal catalysts at room temperature to afford γ‐substituted γ‐lactams in good yields. It has been revealed that the quasi‐divided cell which provided high current density on the anode was crucial for this reaction.     

Study on the layer structure of W/C multilayers deposited by magnetron sputtering using x‐ray reflectivity

A study on the layer structure of W/C multilayers deposited by magnetron sputtering is reported. In the study, soft x‐ray resonant reflectivity and hard x‐ray grazing incidence reflectivity of the W/C multilayers were measured. The imperfections at the interface such as interdiffusion and formation of compounds were dealt with by two methods. On analyzing the experimental results, we found that the incorporation of an interlayer was a more suitable method than the traditional statistical method to describe the layer structure of a W/C system we fabricated. The optical constants of each layer at a wavelength of 4.48 nm were also obtained from the analysis. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis of phenanthridine and phenanthridinone derivatives based on Pd‐catalyzed C–H activation

This review article provides an overview of the most recent and exciting developments in palladium‐catalyzed C–H activation and mechanistic aspects of these catalytic reactions as the fast‐growing field for the synthesis of phenanthridine derivatives.     

Aromatic C–H bond activation revealed by infrared multiphoton dissociation spectroscopy

Metal‐oxide cations are models of catalyst mediating the C–H bond activation of organic substrates. One of the most powerful reagents suggested in the gas phase is based on CuO⁺. Here, we describe the activation of the aromatic C–H bonds of phenanthroline in its complex with CuO⁺. The reaction sequence starts with a hydrogen atom abstraction by the oxygen atom from the 2‐position of the phenanthroline ring, followed by OH migration to the ring. Using infrared multiphoton spectroscopy, it is shown that the reaction can be energetically facilitated by additional coordination of a water ligand to the copper ion. As the reaction is intramolecular, a spectroscopic characterization of the product is mandatory in order to unambiguously address the reaction mechanism. Copyright © 2012 John Wiley & Sons, Ltd.     

Manganese(I)‐Catalyzed C–H Aminocarbonylation of Heteroarenes

A versatile manganese(I) catalyst was employed in C? H aminocarbonylation reactions of heteroarenes with aryl as well as with alkyl isocyanates using a removable directing group approach. Detailed experimental mechanistic studies were suggestive of an organometallic C? H manganesation step, followed by a rate‐determining migratory insertion.