UV accelerated aging and aging resistance of dihydroxy poly(p‐phenylene benzobisoxazole) fibers

By introducing binary hydroxyl groups into poly(p‐phenylene benzoxazole) (PBO) macromolecular chains, we synthesized dihydroxy poly(p‐phenylene benzobisoxazole) (DHPBO) polymers and then prepared DHPBO fibers by dry‐jet wet‐spinning. Comparative studies were performed between intrinsic PBO fibers and DHPBO fibers. The effects of hydroxyl polar groups on improving the UV aging resistance of PBO fibers were investigated. With the introduction of hydroxyl groups, substantial changes in the chemical structures and surface morphologies of DHPBO fibers were observed. As proved by tensile testing and intrinsic viscosity measurement, the UV resistance of DHPBO fibers is obviously improved compared to that of intrinsic PBO fibers. XRD results indicate that the UV aging of these fibers occurs mainly on the surfaces of fibers. Based on these results, the mechanism of UV aging of PBO fibers was discussed. Copyright © 2009 John Wiley & Sons, Ltd.     

Surface characteristic of poly(p‐phenylene terephthalamide) fibers with oxygen plasma treatment

Oxygen plasma is widely employed for modification of polymer surfaces. Plasma treatment process is a convenient procedure that is also environmentally friendly. This study reports the effects of oxygen plasma treatment on the surface properties of poly(p‐phenylene terephthalamide) (PPTA) fibers. The surface characteristics before and after oxygen plasma treatment were analyzed by XPS, atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA). It was found that oxygen plasma treatment introduced some new polar groups (O? C?O) on the fiber surface, increased the fiber surface roughness and changed the surface morphologies obviously by plasma etching and oxidative reactions. It is also shown that the fiber surface wettability was improved significantly by oxygen plasma treatment. Copyright © 2008 John Wiley & Sons, Ltd.     

Improvement of PBO fiber surface and PBO/PPESK composite interface properties with air DBD plasma treatment

The interface of fibrous composites is a key factor to the whole properties of the composites. In this study, the effects of air dielectric barrier discharge (DBD) plasma discharge power density on surface properties of poly(p‐phenylene benzobisoxazole) (PBO) fiber and the interfacial adhesion of PBO fiber reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite were investigated by several characterization methods, including XPS, SEM, signal fiber tensile strength, interlaminar shear strength, and water absorption. After the air DBD plasma treatment at a power density of 41.4 W/cm³, XPS analysis showed that some polar functional groups were introduced on the PBO fiber surface, especially the emergence of a new oxygen‐containing group (?O–C = O group). SEM observations revealed that the air DBD plasma treatment had a great influence on surface morphologies of the PBO fiber, while the signal fiber tensile strength results showed only a small decline of 5.9% for the plasma‐treated fiber. Meanwhile, interlaminar shear strength value of PBO/PPESK composite was increased to 44.71 MPa by 34.5% and water absorption of the composite decreased from 0.46% for the untreated specimen to 0.27%. The results showed that the air DBD plasma treatment can effectively improve the properties of the PBO fiber surface and the PBO/PPESK composite interface. Results obtained from the above analyses also showed that both the fiber surface and the composite interface performance would be reduced when an undue plasma discharge power density was applied. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface modification of high-performance polymeric fibers by an oxygen plasma. A comparative study of poly(p-phenylene terephthalamide) and poly(p-phenylene benzobisoxazole)

Poly(p-phenylene terephthalamide) (PPTA) and poly(p-phenylene benzobisoxazole) (PBO) fibers were exposed to an oxygen plasma under equivalent conditions. The resulting changes in the surface properties of PPTA and PBO were comparatively investigated using inverse gas chromatography (IGC) and atomic force microscopy (AFM). Both non-polar (n-alkanes) and polar probes of different acid-base characteristics were used in IGC adsorption experiments. Following plasma exposure, size-exclusion phenomena, probably associated to the formation of pores (nanoroughness), were detected with the largest n-alkanes (C(9) and C(10)). From the adsorption of polar probes, an increase in the number or strength of the acidic and basic sites present at the fiber surfaces following plasma treatment was detected. The effects of the oxygen plasma treatments were similar for PPTA and PBO. In both cases, oxygen plasma introduces polar groups onto the surfaces, involving an increase in the degree of surface nanoroughness. AFM measurements evidenced substantial changes in the surface morphology at the nanometer scale, especially after plasma exposure for a long time. For the PBO fibers, the outermost layer - contaminant substances - was removed thanks to the plasma treatment, which indicates that this agent had a surface cleaning effect.     

Improvement of interfacial adhesion for plasma‐treated aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) composite and fiber surface aging effects

Interfacial adhesion between the fiber and the matrix in a composite is a primary factor for stress transfer from the matrix to the fiber. In this study, oxygen plasma treatment method was applied to modify the fiber surface for improving interfacial adhesion of aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite. Composite interfacial adhesion properties were determined by interlaminar shear strength (ILSS) using a short‐beam bending test. The composite interfacial adhesion mechanism was discussed by SEM. The changes of chemical composition and wettability for plasma‐treated fiber surfaces stored in air as long as 10 days were investigated by XPS and dynamic contact angle analysis (DCAA), respectively. Results indicated that oxygen plasma treatment was an effective method for improving interfacial adhesion; plasma‐treated fiber surface suffered aging effects during storage in air. Copyright © 2008 John Wiley & Sons, Ltd.     

In situ polymerization and characterization of graphene oxide‐co‐poly(phenylene benzobisoxazole) copolymer fibers derived from composite inner salts

A facile and efficient strategy for preparing well dispersed graphene oxide (GO)‐co‐Poly(phenylene benzobisoxazole) (PBO) copolymer fibers was carried out by direct in situ polycondensation of composite inner salts. The composite inner salts were achieved to improve the dispersivity, solubility, reactivity, and interfacial adhesion of GO in PBO polymer matrix. The structure and morphology of GO‐co‐PBO copolymer fibers have been characterized. It was demonstrated that GO were covalently incorporated with PBO molecular chains and dispersed considerably well in PBO fiber even the GO reach to 3 wt %. Meanwhile, the tensile modulus, tensile strength and thermal stability of GO‐co‐PBO copolymer fibers increased considerably with GO. The mechanism and theoretical calculation of GO enhanced PBO fiber were also discussed. The main reasons for the improvement on performance of PBO fiber should be attributed to good dispersion GO in PBO matrix and covalent bonding networks at the interface between GO and PBO molecular chains. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Hyperbranched polybenzoxazoles incorporated polybenzoxazoles for high‐performance and low‐K materials

This paper reports an effective approach for the fabrication of low‐k polybenzoxazole (PBO) by covalent incorporation of hyperbranched PBO (HBPBO). Soluble o‐aminophenol‐terminated HBPBO was first synthesized by a one‐pot polycondensation, then covalently bonded to poly(hydroxyamide) ended with carbonyl chloride groups, PBO was finally obtained by thermal conversion of the precursor polymers. It was demonstrated that the thermal stability of PBO was not influenced by the incorporation of HBPBO due to their similar chemical compositions, while the glass transition temperature, elastic modulus and hardness were improved because of the linking effects of HBPBO to linear PBO chains. The dielectric constant of PBO was significantly reduced due to the disturbed chain packing of PBO by the globular HBPBO, and the intrinsic cavities in HBPBO, which increased free volume in the materials. Moreover, the material also exhibited reduced coefficient of thermal expansion as compared to neat PBO and low water absorption. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1623–1632     

Aging behavior of dielectric barrier discharge‐modified Twaron fibers in different storage environments

The aging behavior of air dielectric barrier discharge plasma treatment was investigated by storing the treated fibers respectively in air and in the oxidizing environment. Based on several testing methods, this study led us to the conclusion that the aging effects in the oxidizing environment were less obvious than that in air. X‐ray photoelectron spectroscopy and Fourier transform infrared spectroscopy indicated that the decay of fiber surface polar groups was more remarkable for fibers aged in air. The atomic force microscopy photos showed that the further oxidation generated by the oxidizing chemicals such as ozone increased fiber surface roughness. Thus, there was no obvious reduction in the wettability of the modified fibers during the aging process in the oxidizing environment. These changes in surface properties could explain the variation in interlaminar shear strength of Twaron fiber reinforced composites. After the fibers were aged in air for 48 h, interlaminar shear strength of the composites declined by 18.4% while had a decrease of only 11.4% after aging for 48 h in the case of the oxidizing environment. The results were supported by the water absorption test, which also reflected the effects of different storage conditions on the composite interfacial adhesion, and showed the inhibitory effect of the oxidizing environment on plasma aging. Copyright © 2016 John Wiley & Sons, Ltd.     

The synthesis,characterization, and crystal structures of poly(2,6‐naphthalenebenzobisoxazole) and poly(1,5‐naphthalenebenzobisoxazole)

The rigid‐rod polymers, poly(2,6‐naphthalenebenzobisoxazole) (Naph‐2,6‐PBO) and poly(1,5‐naphthalenebenzobisoxazole) (Naph‐1,5‐PBO) were synthesized by high temperature polycondensation of isomeric naphthalene dicarboxylic acids with 4,6‐diaminoresorcinol dihydrochloride in polyphosphoric acid. Expectedly, these polymers were found to have high thermal as well as thermooxidative stabilities, similar to what has been reported for other polymers of this class. The chain conformations of Naph‐2,6‐PBO and Naph‐1,5‐PBO were trans and the crystal structures of Naph‐2,6‐PBO and Naph‐1,5‐PBO had the three‐dimensional order, although the axial disorder existed for both Naph‐2,6‐PBO and Naph‐1,5‐PBO. Naph‐2,6‐PBO exhibited a more pronounced axial disorder than Naph‐1,5‐PBO because of its more linear shape. The repeat unit distance for Naph‐2,6‐PBO (14.15 Å) was found to be larger compared with that of Naph‐1,5‐PBO (12.45 Å) because of the more kinked structure of the latter. The extents of staggering between the adjacent chains in the ac projection of the crystal structure were 0.25c and 0.23c for Naph‐2,6‐PBO and Naph‐1,5‐PBO, respectively. Naph‐1,5‐PBO has a more kinked and twisted chain structure relative to Naph‐2,6‐PBO. The kinked and twisted chain structure of Naph‐1,5‐PBO in the crystal seems to prevent slippage between adjacent chains in the crystal structure. The more perfect crystal structure of Naph‐1,5‐PBO may be due to this difficulty in the occurrence of the slippage. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1948–1957, 2006     

Stress distribution in poly‐p‐phenylenebenzobisoxazole (PBO) fiber as viewed from vibrational spectroscopic measurement under tension. I. Stress‐induced frequency shifts of Raman bands and molecular deformation mechanism

To clarify the relationship between a molecular deformation mechanism and a high Young's modulus of poly‐p‐phenylenebenzobisoxazole (PBO), Raman spectra were measured for fibers subjected to a tensile stress along the chain axis. The stress‐induced frequency shift of the observed Raman bands could be reproduced reasonably by the normal‐mode calculation under a quasi‐harmonic approximation. The frequency position at zero stress and the shift factor of Raman bands were predicted for a PBO chain that agreed with the actually evaluated values. On the basis of these analyses, the molecular deformation mechanism of the PBO chain has been discussed in detail. The crystalline modulus of the PBO chain was calculated theoretically to be 458 GPa, in good agreement with the X‐ray observed value of 460 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1269–1280, 2002     

Novel synthesis of high‐molecular‐weight prepolymer of poly(p‐phenylene benzoxazole) in ionic liquids

Using ionic liquids (ILs) as the reaction solvent for the synthesis of prepolymer polyamide of poly(p‐phenylene benzoxazole) (PBO) was investigated. The optimum condition of prepolymer preparation was determined in ILs. A series of 1,3‐dialkylimidazolium ILs were used to be the reaction media of the polycondensation. The relationship between the molecular weight of prepolymer and the structure of ILs was analysed by changing the structure of the cation and species of anion of ILs. In order to prove the feasibility of the transformation, the prepolymer was used to prepare PBO in polyphosphoric acid media, and the conversion process was analyzed. The spinnability of the PBO solution was explored by the preparation of PBO fibers. The basic mechanical properties of PBO single fiber were tested. In a word, using 1,3‐dialkylimidazolium ILs as the reaction solvents was feasible for the synthesis of high‐molecular‐weight PBO prepolymer, which could be a promising PBO preparation method.     

Resonance raman spectra of poly‐(p‐phenylenebenzobisoxazole), poly‐(p‐phenylenebenzobisthiazole), and poly(pyridobisimidazole)

Resonance Raman spectra of poly(p‐phenylenebenzobisoxazole) (PBO), poly(p‐phenylenebenzobisthazole) (PBZT), and poly(pyridobisimidazole) (PIPD) were measured. In the case of PBO, no large dependence on wavelength of excited laser can be observed, whereas in the cases of PBZT and PIPD, the spectra depends on wavelength of excited laser. This difference may be attributed to the colors of the samples: PBO is gold, and PBZT and PIPD are metallic blue, which show the different conjugated states. The spectra of PBO are rather simpler than those of PBZT and PIPD. This is considered to be reflected by the fact that only a chain passes through the unit cell of PBO, while two chains pass through the unit cell of PBZT and PIPD. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1791–1793, 2001     

抗紫外老化聚对苯撑苯并二噁唑(PBO)纤维的制备与表征

通过化学添加2,5-二羟基对苯二甲酸(DHTA)共聚,以及添加金红石型纳米TiO2物理共混的方法,制备了聚对苯撑苯并二噁唑(PBO)的抗紫外改性纤维.考察了纤维的力学性能、特性粘度及表面形貌在紫外老化过程中的变化,并结合PBO纤维紫外加速老化后的红外分析,对PBO纤维的光老化机理进行了初步研究.结果表明,本实验所制备的DHPBO纤维以及DHPBO/n-TiO2纤维的抗紫外老化能力明显高于PBO纤维,并且金红石型纳米TiO2对PBO的抗紫外改性效果要优于有机紫外吸收剂(2,2'-(1,2-乙烷二基)双(4,1-亚苯基)双苯并噁唑).     

Stress distribution in poly‐p‐phenylenebenzobisoxazole (PBO) fiber estimated from vibrational spectroscopic measurement under tension. II. Analysis of inhomogeneous stress distribution in PBO fiber

Fourier transform Raman spectra were measured for poly‐p‐phenylenebenzobisoxazole (PBO) fiber subjected to a tensile stress, and the Raman shift factor (the frequency shift caused by 1 GPa tensile stress) depended strongly on the sample‐preparation condition. To clarify the reasons of this dependency, a mechanical series parallel model was adopted that could successfully and quantitatively explain the observed Raman shift factors and gave a concreate heterogeneous stress distribution in the PBO fibers. As a result, a mechanical series model was reasonable for PBO fiber. Broadening of Raman bands, which was observed when the PBO fiber was tensioned, could also be interpreted on the basis of an idea of heterogeneous stress distribution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1281–1287, 2002     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

X‐ray photoelectron spectroscopy and time‐of‐flight secondary ion mass spectrometry characterization of aging effects on the mineral fibers treated with aminopropylsilane and quaternary ammonium compounds

X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry were used to investigate the aging effects on the aminopropylsilane (APS) and quaternary ammonium surfactant‐treated mineral fibers. APS‐coated mineral fiber samples were treated with cationic surfactant and mineral oil and aged at 70 °C temperature and 95% humidity. From quantitative XPS measurements, an increase in the atomic composition of oxygen, nitrogen, and silicon is observed after aging. An increase in the protonated amino groups in the N1s high‐resolution spectra and C–N group in the C1s high‐resolution spectra is also observed. These results indicate that the concentration of hydrocarbon groups decreases after aging due to the partial removal of the long hydrocarbon chains of the surfactant and mineral oil and/or hydrolysis and segregation of APS to the fiber surface. The principal component analysis (PCA) was applied to the time‐of‐flight secondary ion mass spectrometry spectra, and an increase in the intensities of APS characteristic peaks were observed after aging. The observed increase in the signals of APS originates from underlying silanized fibers after the removal of the surfactant and mineral oil from the surface. Copyright © 2012 John Wiley & Sons, Ltd.     

Wettability of poly(styrene‐co‐acrylate) ionomers improved by oxygen‐plasma source ion implantation

The surfaces of poly(styrene‐co‐acrylic acid) copolymers and their Na‐ and Cs‐neutralized ionomers were modified by O₂‐plasma source ion implantation (PSII) treatment to improve the surface wettability. The changes in the surface wettability, composition, and structure upon the PSII treatment were examined with contact‐angle measurements and X‐ray photoelectron spectroscopy. The untreated surfaces of the acid copolymers and ionomers exhibited different surface energies; this implied clearly that the type of ion species affects the surface hydrophilicity. Also, the PSII treatment induced oxygen‐containing groups to reside on the surface and ionic groups to come out toward the surface; this made the surfaces of the ionomers more hydrophilic as compared with that of the acid copolymers. The ionomers also showed slow hydrophobic recovery. Thus, it was suggested that the reduced mobility of the polymer chain because of the presence of ionic aggregates results in restricted reorientation of oxygen‐containing groups. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1791–1797, 2003     

Study of the wettability properties of polypropylene nonwoven mats by low‐pressure oxygen plasma treatment

Surface modification by plasma treatment is widely used for textiles and polymeric materials. Plasma processes are environmentally friendly and reduce chemicals and energy consumption. This study reports the effect of cold, low‐pressure oxygen plasma on the wettability properties of polypropylene (PP) nonwoven mats. The wetting properties were examined using contact angle, surface energy, and diameters of the drop after 20 s of treatment. It was found that plasma treatment had a significant effect on the wettability of PP fibers. The ageing for 90 days had no significant effect on the wettability. It was also shown that the morphology of the fibers was not affected by the plasma treatment. Copyright © 2007 John Wiley & Sons, Ltd.     

连续纤维增强含二氮杂萘酮联苯结构聚芳醚砜酮树脂基复合材料的界面

利用射频感性耦合冷等离子体(ICP)处理技术改性连续纤维表面,分别采用X射线光电子能谱(XPS)、原子力显微镜(AFM)及动态接触角分析(DCA)系统研究了等离子体处理时间、放电气压、放电功率等工艺参数对连续碳纤维、芳纶纤维和对亚苯基苯并二噁唑(PBO)纤维的表面化学成分、表面形貌、表面粗糙度及表面自由能的影响.研究结...     

Ultrafine hydrogel fibers with dual temperature‐ and pH‐responsive swelling behaviors

Ultrafine hydrogel fibers that were responsive to both temperature and pH signals were prepared through the electrospinning of poly(N‐isopropylacrylamide) (PNIPAAm) and poly(acrylic acid) mixtures in dimethylformamide. Both the diameters (700 nm to 1.2 μm) and packing of the fibers could be controlled through changes in the polymer compositions and PNIPAAm molecular weights. These fibers were rendered water‐insoluble by the addition of either Na₂HPO₄ or poly(vinyl alcohol) (PVA) to the solution, followed by the heat curing of the fibers. The fibers crosslinked with Na₂HPO₄ swelled to 30–120 times in water; this was significantly higher than the swelling of those crosslinked with PVA. The PVA‐crosslinked hydrogel fibers, however, exhibited faster swelling kinetics; that is, they reached equilibrium swelling in less than 5 min at 25 °C. They were also more stable after 1 week of water exposure; that is, they lost less mass and retained their fibrous form better. All the hydrogel fibers showed a drastic increase in the swelling between pH 4 and 5. The PVA‐crosslinked hydrogel fibers exhibited distinct temperature‐responsive phase‐transition behavior of PNIPAAm, whereas the Na₂HPO₄‐crosslinked hydrogel fibers showed altered two‐stage phase transitions that reflected side‐chain modification of PNIPAAm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6331–6339, 2004