Structural,electrical and optical properties of MgO-reduced graphene oxide nanocomposite for optoelectronic applications

MgO-reduced graphene oxide nanocomposites (NCs) were synthesized by a simple two-step chemical method. The microstructure, surface morphology, and composition of the prepared samples have been studied. X-ray diffractometer (XRD) analysis confirmed the crystalline cubic MgO nanoparticle and rGO sheets. Scanning electron microscope (SEM) showed the spherical MgO nanoparticles well dispersed over the graphene sheets. UV–visible spectroscopy analysis demonstrated that a red shift in the wavelength dependent absorbance curve. The band gap of the samples was found to be decreased with the increase of rGO content. The dielectric studies have been examined in the frequency range 500 Hz−5 MHz and found significant improvement in the dielectric constant, dielectric loss, and electric properties due to rGO addition.This is mainly attributed to the strong interfacial polarization (Maxwell–Wagner polarization) between MgO and rGO sheets. Further, the modulation of charge carrier density with rGO additions help to enhance the electrical conductivity of NCs and thus, encouraging to have wider application in electronic and energy technologies.     

Ultrasound-assisted surface treatment of ZrO2 with BSA and incorporating in PVC to improve the properties of the obtained nanocomposites: Fabrication and characterization

This paper describes the preparation of poly(vinyl chloride) (PVC) nanocomposites (NCs) reinforced with modified zirconia (ZrO₂) nanoparticles (NPs). The ZrO₂ NPs were defined as efficient filler for PVC NCs. For achieving the best dispersion and improvement of properties, the surface of ZrO₂ NPs was modified by Bovine Serum Albumin (BSA). Carboxylic acids and amines are important functional groups of BSA which handle the grafting BSA on the surface of ZrO₂ NPs. The PVC/ZrO₂-BSA NCs were fabricated by incorporation of various amounts of the ZrO₂-BSA NPs (3, 6 and 9 wt%) into PVC matrix. All the above processes were accomplished by ultrasonication as a green and environmentally-friendly method. Also, the magnetic and mechanical stirrer was used for the preparation of samples but the results are not suitable and the aggregation was observed which indicated the use of ultrasonic irradiation is the best method for the preparation of NC. The products were characterized by Fourier transform infrared spectroscopy, Transmission electron microscopy, Field emission scanning electron microscopy, X-ray diffraction, Thermogravimetric analysis, Ultraviolet–visible spectroscopy, photoluminescence spectroscopy, energy dispersive X-ray spectroscopy, wettability, and mechanical tests. The achieved PVC/ZrO₂-BSA NCs showed high thermal stability, good mechanical, optical and wettability properties compared to the pure PVC. In addition, among the obtained NCs, the PVC/ZrO₂-BSA NC 6 wt% showed the best improvement.     

Nanocomposite materials based on poly(vinyl chloride) and bovine serum albumin modified ZnO through ultrasonic irradiation as a green technique: Optical,thermal, mechanical and morphological properties

In this project, physicochemical properties of poly(vinyl chloride) (PVC) reinforced by ZnO nanoparticles (NPs) were studied. Firstly, ZnO NPs were modified with bovine serum albumin (BSA) as an organo-modifier and biocompatible substance through ultrasound irradiation as environmental friendly, low cost and rapid means. Nanocomposite (NC) films were prepared by loadings of various ratios of ZnO/BSA NPs (3, 6 and 9 wt%) inside the PVC. Structural morphology and physical properties of the ZnO-BSA NPs and NC films were investigated via Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis (TGA), transmission electron microscopy and field emission scanning electron microscopy. According to the obtained information from the TGA, an increase in the thermal stability can be clearly observed. Also the results of contact angle analysis indicated with increasing percent of ZnO/BSA NPs into PVC the hydrophilic behaviors of NCs were increased.     

Ultrasonic-assisted fabrication and characterization of PVC-SiO2 nanocomposites having bovine serum albumin as a bio coupling agent

In this work, SiO₂ nanoparticles (NPs) were modified with bovine serum albumin (BSA) under ultrasound irradiations as a green and fast route to achieve their good dispersion. Subsequently, different weight percentages of the modified NPs (3, 6, and 9 wt%) were incorporated in poly(vinyl chloride) (PVC) as the matrix. Thermogravimetric analysis of the SiO₂-BSA NPs indicated that 12 wt% of the modifier was loaded on the surface of SiO₂ NPs. Encapsulation of the SiO₂-BSA resulted in a meaningful improvement in the optical, mechanical and thermal characteristics of the prepared PVC nanocomposites (NCs). X-ray diffraction (XRD) patterns for the PVC/SiO₂-BSA NCs showed a crystalline behavior for the NC with 6 wt% of the SiO₂-BSA originated from the phosphate buffer on the NPs. Water contact angle of the PVC/SiO₂-BSA NCs showed that the hydrophilicity enhanced with increasing of the NPs contents.     

Phase transition induced formation of hollow structures in colloidal lanthanide-doped NaYF<Subscript>4</Subscript> nanocrystals

Formation of colloidal hollow structures in NaYF₄ nanocrystals (NCs) with and without lanthanide ion doping has been observed and investigated via the co-thermolysis of a mixture of trifluoroacetate precursors in trioctylphosphine oxide. The Kirkendall effect in this one-step reaction is driven by the monomer diffusion and crystal phase transition. It is found that three kinetic stages which include rapid precipitation of cubic phase NCs, cubic to hexagonal phase transition concurrent with an inward transport of NaF species, and vacancy diffusion are attributed to the hollow structure formation. X-ray energy dispersive spectroscopy (XEDS) point analysis is applied to examine the ions distribution and crystalline components in the lanthanides (Yb and Er)-doped NaYF₄ up-conversion nanophosphors (UCNPs). The hollow structures increase the surface-to-volume of a single NC and thus have a significant effect on the photoluminescence of the lanthanide-doped NPs and provide synthetic applications for achieving novel NaYF₄-based NCs.     

Solution-processed Au@rGO/GaN nanorods hybrid-structure for self-powered UV,visible photodetector and CO gas sensors

Although metal nanoparticles (NPs) have been widely reported, Au NPs functionalized reduced graphene oxide (rGO)/GaN nanorods (NRs) for multi-functional applications are rarely discussed. The rGO is a well known transparent electrode and has been considering an alternative electrode to ITO in the current optoelectronic community. In this work, Au NPs functionalized rGO (Au@rGO)/GaN NRs hybrid structure probed for photodetector and CO gas sensing applications. The hybrid structure was characterized by scanning electron microscopy, transmission electron microscope, current-voltage characteristics, photo conductivity, and gas sensor measurements. The Au@rGO/GaN NRs showed higher photoresponsivity (λ = 382 nm, 516 nm) compared to rGO/GaN NRs at room temperature. The rising and falling times of Au@rGO/GaN NRs are faster than that of rGO/GaN NRs. The hybrid structure Au@rGO/GaN NRs exhibited high CO gas response compared to rGO/GaN NRs at room temperature (∼38% to the 20 ppm). Au NPs played an important role in terms of electronic and chemical changes in the hybrid structure for improving both photodetectors the CO gas response. Such a multi-functional hybrid device is an interest of various room temperature applications.     

Compare the photocatalytic properties of nanocomposites with tandem n (AgBr)-n (Ag2CO3) and p (AgCl)-n (Ag2CO3) heterojunctions

In this work, Ag₂CO₃ nanoparticles (NPs) (as a n-type semiconductor) incorporated in mordenite zeolite (MOR) by a facile precipitation method. Silver halides, AgCl (as a p-type semiconductor) and AgBr (as a n-type semiconductor), with different weight percentage (20%, 40% and 50%) were coupled into Ag₂CO₃-MOR nanocomposite (NC) and producing a series of novel AgCl/Ag₂CO₃ (p-n heterojunction)-MOR and AgBr/Ag₂CO₃ (n-n heterojunction)-MOR NCs. The effects of silver halides on the Ag₂CO₃–MOR catalyst for the photocatalytic degradation of methyl blue (MB) under visible light irradiation have been investigated. The structure, composition and optical properties of NCs were investigated by UV–Visible diffuse reflectance spectroscopy (UV–Vis DRS), X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM). The prepared AgX/Ag₂CO₃-MOR NCs with the optimal content of AgX (50 wt%) indicated higher photocatalytic activity than that of the Ag₂CO₃-MOR and Ag₂CO₃. The cycle experiments on the heterojuctions NCs indicated that photocatalytic stability of AgBr/Ag₂CO₃-MOR NC was more than AgCl/Ag₂CO₃-MOR NC in all cycles. On the basis of the experimental results, a possible mechanism for the enhanced photocatalytic activity and photoinduced stability of silver compounds was proposed.     

Synthesis and characterization of polypyrrole/Sn-doped TiO2 nanocomposites (NCs) as a protective pigment

We have chemically polymerized pyrrole in the presence of Sn-doped TiO₂ nanoparticles (NPs) and TiO₂ (NPs) which act as a protective pigment. Field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) results show a core-shell structure of pigments in which TiO₂ and Sn-doped TiO₂ NPs have a nucleus effect and caused a homogenous PPy core-shell type morphology leading to coverage of the TiO₂ and Sn-doped TiO₂ NPs by PPy deposit. The XRD results indicate that the crystalline size of polypyrrole/TiO₂ NCs and polypyrrole/Sn-doped TiO₂ NCs were approximately 93.46 ± 0.06 and 23.36 ± 0.06 nm respectively. The electrochemical impedance spectroscopy (EIS) results show that the performance of polypyrrole/Sn-doped TiO₂ NCs is better than polypyrrole/TiO₂ NCs. The results indicate that increasing the area of synthesized polypyrrole in the presence of Sn-doped TiO₂ NPs can increase its ability to interact with the ions liberated during the corrosion reaction of steel in the presence of NaCl. The UV-vis results show that the band gap of TiO₂ NPs increases with doped of Sn in lattice of TiO₂. The increase of the band gap of TiO₂ with doping of Sn can decrease the charge transfer through the coating.     

Synthesis and characterization of superparamagnetic nanoparticles coated with fluorescent gold nanoclusters

Multifunctional nanoparticles (NPs) combining the superparamagnetism of Mn−Zn ferrite and the fluorescence property of gold nanoclusters (NCs) have been prepared by wet chemistry. Magnetic NPs synthesized by co-precipitation method were coated several times with oppositely charged polyelectrolytes (PEs) using the layer-by-layer technique. Common techniques (Fourier transform infrared spectroscopy, electron microscopy, zeta potential, etc.) indicated the monodispersity and the stability of the coated NPs providing a positive charged surface. Fluorescent gold NCs bound to a standard protein bovine serum albumin were adsorbed on the surface of the magnetic NPs. Structural investigations proved the presence of small gold clusters (~2 nm) in a shell surrounding the magnetic nanomaterial. The stable nanocomposite kept the original fluorescence property of the metal clusters with 211-fold increase of the red emission (λ = 690 nm) compared to the uncoated NPs. These NPs can be moved with a permanent magnet despite a 72-wt% increase of the non-magnetic fraction due to the PE coating and the protein adsorption.     

Charge retention in quantized energy levels of nanocrystals

Understanding charging mechanisms and charge retention dynamics of nanocrystal (NC) memory devices is important in optimization of device design. Capacitance spectroscopy on PECVD grown germanium NCs embedded in a silicon oxide matrix was performed. Dynamic measurements of discharge dynamics are carried out. Charge decay is modelled by assuming storage of carriers in the ground states of NCs and that the decay is dominated by direct tunnelling. Discharge rates are calculated using the theoretical model for different NC sizes and densities and are compared with experimental data. Experimental results agree well with the proposed model and suggest that charge is indeed stored in the quantized energy levels of the NCs.     

Utilization of ultrasonic irradiation as a green and effective strategy to prepare poly(N-vinyl-2-pyrrolidone)/modified nano-copper (II) oxide nanocomposites

The present paper describes the result of investigations into preparation of novel nanocomposites (NCs) based on poly(N-vinyl-2-pyrrolidone) (PVP) as a biocompatible polymer and modified copper (II) oxide nanoparticles (NPs) as a nano-filler. To achieve optimum NCs properties, different ratios of modified copper (II) oxide NPs (3, 5, and 7 wt%) were used to fabricate PVP NCs and also the ultrasonic irradiation was utilized to perform these processes as a fast and effective method. Subsequently, the structure of the obtained nanohybrids was characterized by various techniques. The suitable incorporation between PVP matrix and modified CuO NPs can be seen from the FT-IR spectra. The obtained NCs indicated an efficient thermal improvement in comparison to the pristine polymer. Also, the uniform dispersion of modified CuO NPs in the PVP matrix was detected by FE-SEM and EDX. According to UV absorption spectra, it is clear that these NCs can be used in UV protecting applications.     

Pd/C催化剂在乙炔选择加氢反应中的催化性能：载体效应

Pd/C catalysts were prepared by deposited Pd nanoparticles (NPs) on different carbon supports including activated carbon (AC), graphite oxide (GO), and reduced graphite oxide (rGO) using sol-immobilization method. Through transmission electron microscopy, powder X-ray di raction, and X-ray photoelectron spectroscopy, the role of the carbon supports for the catalytic performances of Pd/C catalysts was examined in selective hydrogenation of acetylene. The results indicate that Pd/AC exhibited higher activity and selectivity than Pd/GO and Pd/rGO in the gas phase selective hydrogenation of acetylene. Thermal and chemical treatment of AC supports also have some effect on the catalytic performance of Pd/AC catalysts. The differences in the activity and selectivity of various Pd/C catalysts were partly attributed to the metal-support interaction.     

Structures,Oxidation, and Charge Transport of Phosphorus‐Doped Germanium Nanocrystals

The doping of semiconductor nanocrystals (NCs) is crucial for the optimization of the performance of devices based on them. In contrast to recent progress on the doping of compound semiconductor NCs and silicon NCs, the doping of germanium (Ge) NCs has lagged behind. Here it is shown that Ge NCs can be doped with phosphorus (P) during synthesis by a nonthermal plasma. It is found that there are more P atoms in the NC near‐surface region than in the NC core. P doping modifies the surface state of Ge NCs. Compressive strain can be incuced in Ge NCs by P which can explain the P‐doping‐enhanced oxidation resistance of Ge NCs. Stable dispersions of P‐doped Ge NCs in acetonitrile can be cast to produce films for field‐effect transistors (FETs). FET analysis shows that the electrical conductivity and electron mobility of a Ge‐NC film increase with the increase of the P doping level, although the electrical activation efficiency of P in the Ge‐NC film is low. Finally, atomic layer deposition of aluminum oxide at the surface of P‐doped Ge NCs is shown to improve the performance of the FETs.     

Antibacterial effects of chitosan–tripolyphosphate nanoparticles: impact of particle size molecular weight

A simple fabrication approach for achieving nanoparticle patterns based on a room temperature chemically driven strategy is reported. Suitably engineered colloidal luminescent nanocrystals (NCs) (4 and 6 nm in diameter), namely organic capped and silica-coated negatively charged CdSe@ZnS NCs, have been selectively assembled onto defined domains in a binary hydrophobic/hydrophilic chemical pattern, purposely fabricated by combining microcontact printing and wet chemistry procedures. The goal of the work has been to investigate the experimental parameters governing the assembly process at molecular level, in order to elucidate factors regulating interactions at the interfaces. For this purpose, specific sets of conditions, namely substrate patterns and NCs with distinct surface functionalization, have been prepared and tested using different NC dispersing solvents. The NC assembly has been demonstrated driven by non-covalent forces, namely Van der Waals or electrostatic interactions occurring at the NC/substrate interface. The overall study has provided a comprehensive understanding of the role of solvent and molecular chemistry at interfaces in NC assembling. The obtained results can be valuable to set up reliable procedures for developing reproducible patterning protocols potentially useful for the fabrication of NC-based devices.     

Photophysical manifestations of interactions of quantum dots with ortho-phenanthroline molecules

The interaction of CdSe/ZnS nanocrystals (NCs) (solubilized by trioctylphosphine oxide (TOPO) molecules) with ortho-phenanthroline (OP) molecules has been investigated. It is shown that OP molecules can replace TOPO; in this case, bonding of OP molecules with the nanocrystal surface does not lead to the formation of NC aggregates. It is established that the difference in the evolution of the spectral-luminescence NC characteristics in a mixture with OP is independent of the NC size. A model of the interaction of NCs with OP molecules is proposed.     

Automatically Purification of Aqueous CdTe Nanocrystals in Water-ethanol Co-environment

Purification is a separated post-treatment step after the synthesis of nanocrystals (NCs) in order to exclude excess ligands and monomers in NC solution. The common purification process involves many manipulations, such as concentrating, addition of anti-solvents and centrifugation, which are troublesome and time consuming. In this work, we originally integrate NC synthesis and NC purification in one-pot via selecting water-ethanol co-environment for NC synthesis and NC purification. Our research shows that NCs can grow in water-ethanol mixture. When growing into critical size, NCs will automatically precipitate from the solution. Element analysis demonstrates that precipitates fraction fits well with stoichiometric of ligand-capped NCs. Excess monomers are left in supernatant, and thus achieving automatically purification of NCs in the water-ethanol co-environment. By adjusting the volume ratios of water and ethanol in bi-solvent system, different-sized purified NCs can be controlled. Besides, this water-ethanol co-environment can be used in both thermal-promoted and hydrazine-promoted growth.     

Resonant Raman scattering in CdSxSe1−x nanocrystals: effects of phonon confinement,composition, and elastic strain

Optical phonon modes, confined in CdS_xSe_1−x nanocrystal (NC) quantum dots (≈2 nm in radius) grown in a glass matrix by the melting‐nucleation method, were studied by resonant Raman scattering (RRS) spectroscopy and theoretical modeling. The formation of nanocrystalline quantum dots (QDs) is evidenced by the observation of absorption peaks and theoretically expected resonance bands in the RRS excitation spectra. This system, a ternary alloy, offers the possibility to investigate the interplay between the effects of phonon localization by disorder and phonon confinement by the NC/matrix interface. Based on the concept of propagating optical phonons, which is accepted for two‐mode pseudo‐binary alloys in their bulk form, we extended the continuous lattice dynamics model, which has successfully been used for nearly spherical NCs of binary materials, to the present case. After determining the alloy composition for NCs (that was evaluated with only 2–3% uncertainty using the bulk longitudinal optical phonon wavenumbers) and the NC size (using atomic force microscopy and optical absorption data), the experimental RRS spectra were described rather well by this theory, including the line shape and polarization dependence of the scattering intensity. Even though the presence of a compressive strain in the NCs (introduced by the matrix) masks the expected downward shift owing to the phonons' spatial quantization, the asymmetric broadening of both Raman peaks is similar to that characteristic of NCs of pure binary materials. Although with some caution, we suggest that both CdSe‐like and CdS‐like optical phonon modes indeed are propagating within the NC size unless the alloy is considerably heterogeneous. Copyright © 2011 John Wiley & Sons, Ltd.     

Deciphering the Structure and Chemical Composition of Drug Nanocarriers: From Bulk Approaches to Individual Nanoparticle Characterization

Drug nanocarriers (NCs) with sizes usually below 200 nm are gaining increasing interest in the treatment of severe diseases such as cancer and infections. Characterization methods to investigate the morphology and physicochemical properties of multifunctional NCs are key in their optimization and in the study of their in vitro and in vivo fate. Whereas a variety of methods has been developed to characterize “bulk” NCs in suspension, the scope of this review is to describe the different approaches for the NC characterization on an individual basis, for which fewer techniques are available. The accent is put on methods devoid of labelling, which could lead to artefacts. For each characterization method, the principles and approaches to analyze the data are presented in an accessible manner. Aspects related to sample preparation to avoid artefacts are indicated, and emphasis is put on examples of applications. NC characterization on an individual basis allows gaining invaluable information in terms of quality control, on: i) NC localization and fate in biological samples; ii) NC morphology and crystallinity; iii) distribution of the NC components (drugs, shells), and iv) quantification of NCs’ chemical composition. The individual characterization approaches are expected to gain increasing interest in the near future.     

Ultrasound-assisted synthesis of nanocomposites based on aromatic polyamide and modified ZnO nanoparticle for removal of toxic Cr(VI) from water

In this study, novel nanocomposites (NCs) of aromatic polyamide (PA) and surface modified ZnO nanoparticle with s-triazine heterocyclic ring was introduced for efficient removal of toxic hexavalent chromium (VI) from aqueous solution. The surface of ZnO nanoparticle was modified by s-triazine core silane coupling agent (ZnO-TSC) and PA/ZnO-TSC NCs with different amount of ZnO-TSC nanoparticles (0, 5, 10 and 15 wt%) were prepared by ultrasonic irradiation. The synthesized PA/ZnO-TSC NCs were characterized by FT-IR, XRD, FE-SEM, TEM and TGA methods. TEM images showed that ZnO nanoparticles were dispersed homogeneously in the polymer matrix. The adsorption experiments were carried out in batch mode to optimize various parameters like contact time, pH and concentration of metal ion that influence the adsorption rate. The maximum uptakes of Cr(VI) at pH 4.0 was 72%, 81%, 89% and 91% for pure PA, NC5%, NC10% and NC15%, respectively. The kinetic of adsorption was investigated and the pseudo second-order model is an appropriate model for interpretation of adsorption mechanism of Cr(VI) ions.     

Size-dependent intrinsic radiative decay rates of silicon nanocrystals at large confinement energies

We study ultrafast photoluminescence (PL) dynamics of Si nanocrystals (NCs). The early-time PL spectra (<1 ns), which show strong dependence on NC size, are attributed to emission involving NC quantized states. The PL spectra recorded for long delays (>10 ns) are almost independent of NC size and are likely due to surface-related recombination. Based on instantaneous PL intensities measured 2 ps after excitation, we determine intrinsic radiative rate constants for NCs of different sizes. These constants sharply increase for confinement energies greater than approximately 1 eV indicating a fast, exponential growth of the oscillator strength of zero-phonon, pseudodirect transitions.