Polymer blend membranes of sulfonated poly(arylene ether ketone) for direct methanol fuel cell

The blend membranes of sulfonated poly(arylene ether ketone) (sPAEK) (IEC = 1.0 mequiv./g)/Nafion^® and the blend membranes of sPAEK (IEC = 1.0 mequiv./g)/sPAEK (IEC = 1.7 mequiv./g) were prepared. sPAEK with low IEC was introduced to reduce the methanol permeability through the membrane. Morphology, water uptake, proton conductivity and methanol permeability of the blend membranes were investigated by SEM, AFM, AC impedance spectroscopy and permeability measuring instrument. The cross-sections of blend membranes showed phase-separated morphologies. The effect of phase-separated morphology on the properties of blend membranes was investigated. The properties like water uptake, proton conductivity, and methanol permeability of sPAEK/Nafion^® blend membranes showed similar values with sPAEK and properties of sPAEK/sPAEK blend membranes showed intermediate values of two polymers due to the difference in morphology of the blend membranes. sPAEK/sPAEK blend membranes showed relatively high proton conductivity and lowered methanol permeability compared to Nafion^®. sPAEK/sPAEK blend membranes could be a competent substitution for Nafion^®.     

DMFC用PES/SPEEK共混阻醇质子交换膜

将磺化聚醚醚酮(SPEEK, 磺化度DS为68.3%)和聚醚砜(PES)两种聚合物共混制得PES/SPEEK共混膜. DSC研究表明两种聚合物之间具有较好的相容性, 因而共混膜均匀致密, 未发生大尺度相分离. PES的混入能有效降低膜的溶胀度及甲醇透过系数. 纯SPEEK 膜40 ℃时在1 mol•L−1甲醇水溶液中溶胀度达到160%, 45 ℃时就完全溶解, 而含30%(w)PES的共混膜在80 ℃时的溶胀度仅有15%. 室温下含20%−30%(w)PES的共混膜的甲醇透过系数为1×10−7 cm2•s−1左右, 比Nafion 115膜的透过系数小一个数量级. 尽管80 ℃下30%(w)PES/SPEEK共混膜的电导率与Nafion 115膜相当, 但由于共混膜的厚度比Nafion 115膜小1/3左右, 膜电阻较小, 因而其电池性能比Nafion 115膜的好.     

直接甲醇燃料电池中的膜性能比较

制备了磺化聚醚醚酮(SPEEK)和磺化酚酞型聚醚砜(SPES-C)两种质子交换膜,考察了其质子导电和阻醇性能.实验发现,两种新型质子交换膜具有一定的化学稳定性和质子电导率,尤其在高温下两种新膜的质子电导率与Nafion膜接近.两种新膜的甲醇透过系数要比Nafion膜的低1～2个数量级.分别以两种新型膜和Nafion115膜为电解质制备了直接甲醇燃料电池膜电极,讨论了膜材料的性能对直接甲醇燃料电池性能的影响.结果表明,膜材料的阻醇性越好,电池的开路电压越高;膜的电导率越高,在较高电流密度区域内电池的性能越好.     

SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30wt%)、SPEEK/SPES-C(30wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20wt%)共混膜电导率超过Nafion115膜;温度大于110℃时,SPEEK/SPES-C(30wt%)共混膜电导率与Nafion115膜相当,达到0.11S.cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.     

磺化聚芳醚砜/磺化聚酰亚胺复合质子交换膜的制备与性能研究

利用溶液浇铸法制备了一系列双磺化型磺化聚芳醚砜/磺化聚酰亚胺(SPAES/SPI)复合质子交换膜.扫描电子显微镜(SEM)结果显示复合膜不存在明显的相分离,表明二者具有很好的相容性.由于SPI的引入,复合膜在甲醇中稳定性较纯SPAES具有大幅的提高,比Nafion112低得多的甲醇吸收率表明了这些复合膜具有比后者更低的甲醇透过率.复合膜显示了与单组分膜相类似的高温分解稳定性,磺酸基团的分解温度达到了290℃以上.复合膜显示出远高于纯SPAES膜的尺寸稳定性能,在130℃高温中200h处理后,所有的复合膜均保持了高的机械性能,而此时纯SPAES膜已经溶解于水中.而且由于两种磺化聚合物间的复合,复合膜维持了较高的IEC水平,显示了较高的质子导电率,在80%相对湿度时的质子导电率与Nafion112相近,而在水中的质子导电率均高于Nafion112.     

磺化聚醚酰亚胺/聚醚砜共混型质子交换膜的制备及其性能

以磺化聚醚酰亚胺(SPEI)和聚醚砜(PES)为原料, 采用溶液共混法成功制备出了SPEI/PES共混型质子交换膜,并经热重分析、AFM、SEM等对膜的结构和性能进行了表征. 结果表明, 共混膜较纯SPEI膜具有更高的热稳定性和较低的溶胀性; 在室温环境下, 共混膜在干态和湿态时均具有优异的机械性能; 与纯SPEI膜相比, 共混膜的形态结构更为致密, 这将有利于降低甲醇的渗透性. 采用交流阻抗法和隔膜扩散法分别考察了膜的质子传导性和阻醇性能, 对于共混质量比为50/50的膜来说, 其质子传导率达到了5.5 mS·cm-1的水平, 能满足质子交换膜的需求, 但其甲醇渗透系数明显降低, 仅为市用Nafion 112膜的5%, 这表明该共混膜有望作为一种新型的直接甲醇燃料电池用质子交换膜.     

Modified poly(phthalazinone ether ketone) membranes for direct methanol fuel cell

Sulfonated poly(phthalazinone ether ketone)s (SPPEK)s were synthesized by the modification of poly(phthalazinone ether ketone) (PPEK) with 98% concentrated sulfuric acid or 98% concentrated sulfuric acid and chlorosulfonic acid mixture at 80–100°C. The presence of sulfonic acid groups in SPPEKs was confirmed by Fourier transform infrared (FTIR) analysis and nuclear magnetic resonance (NMR), and the DSs were determined by Energy Dispersive X‐Ray (EDX). A blend membrane of No. 21 SPPEK and phosphotungstic acid (PWA) was prepared. The methanol permeabilities of SPPEK and blend membranes were about 20 times lower than that of Nafion117 at room temperature. The direct methanol fuel cell (DMFC) test of 2 M methanol solution and air breathing showed that the blend membrane had a better performance than that of the Nafion117. Copyright © 2007 John Wiley & Sons, Ltd.     

High performance direct methanol fuel cells based on acid–base blend membranes containing benzotriazole

Novel acid–base blend membranes consisting of acidic sulfophenylated poly(ether ether ketone ketone) (Ph-SPEEKK) and various amounts of basic polysulfone tethered with 5-amino-benzotriazole (PSf-BTraz) have been prepared and characterized. The blend membranes show higher proton conductivity and lower liquid uptake and dimensional swelling compared to plain Ph-SPEEKK and sulfonated poly(ether ether ketone) (SPEEK) membranes. The Ph-SPEEKK/PSf-BTraz blend membranes with optimized basic polymer contents exhibit lower methanol crossover and higher performance with improved stability in direct methanol fuel cells (DMFC) at various methanol concentrations (1–10 M) than plain Ph-SPEEK and Nafion-115 membranes.     

Sulfonated poly(ether ether ketone)/poly(vinylpyrrolidone) acid–base polymer blends for direct methanol fuel cell application

Acid–base polymer blends for polymer electrolyte membranes have been prepared by blending sulfonated poly(ether ether ketone) (SPEEK) with poly(vinylpyrrolidone) (PVP) to reduce methanol uptake and to decrease methanol permeability while maintaining high proton conductivity. The acid‐base interaction occurring on the sulfonic acid group and on the tertiary amide group was characterized by FTIR and DMA. As the composition of PVP lowered than 20 wt % in the blends, the acid–base interaction causes great reduction on methanol uptake and the methanol permeability; however, the proton conductivity is still high. In this work, membrane–electrode assemblies (MEAs) have been prepared for direct methanol fuel cell (DMFC) from both blend membrane and Nafion 117. DMFC single cell performance was also evaluated. Results confirmed that SPEEK (with the degree of sulfonation (DS) = 69%) blended with PVP (M_n = 1,300,000) with a ratio of 80/20 (w/w) exhibits higher open‐circuit voltages (OCV) and lower polarization loss than those of Nafion 117. These acid–base blends will be suitable for DMFC application. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 565–572, 2006     

含杂萘联苯结构聚合物膜的直接甲醇燃料电池性能

质子交换膜是直接甲醇燃料电池(DMFC)的关键组成部分. 通过磺化制备了磺化杂萘联苯聚醚酮(SPPEK)、磺化杂萘联苯聚醚砜(SPPES)和磺化杂萘联苯聚醚砜酮(SPPESK)三种含杂萘联苯结构的新质子交换膜, 测试了其热稳定性、质子导电性和甲醇透过性能. SPPESK的热分解温度比相近离子交换容量(IEC)的SPPEK和SPPES约低100 ℃, 三种膜均具有良好的导电和阻醇性能; 分别以三种膜为电解质组装DMFC考察了其性能, DMFC的开路电压随膜的阻醇性的提高而增大, 三种膜的开路电压均高于Nafion115膜, 但在较高电流密度的区域三种新膜的性能均比Nafion115膜差.     

不同磺化度下的磺化聚醚醚酮对全钒储能液流电池性质影响的研究

本文报道了采用浓硫酸作为磺化剂,成功合成了不同磺化度下的聚醚醚酮(PEEK)膜,并深入研究了磺化条件包括磺化时间和磺化剂的用量对所获薄膜性能的影响,获得了在不同磺化度（DS）下SPPEK膜的离子交换容,含水率,机械性能,质子电导率等参数,特别测定了在全钒液流电池工作条件下钒离子(Ⅳ)渗透率,首次为该类液流储能电池使用价廉质优的质子交换膜提供了基础实验数据。室温条件下的实验结果如下：1）磺化12小时后,膜的磺化度46%,含水量为28%,钒离子(Ⅳ)选择性最佳（钒离子渗透率为1.2×10-7 cm2/min-1,是Nafion117 (2.9×10-6 cm2/min-1)的1/24）,其质子电导率只有0.02 S/cm;2）磺化96小时其磺化度达79%的膜,质子电导率达0.16 S/cm,是Nafion117 (0.10S/cm) 的1.6倍, 但其机械性能最差;3）与Nafion117膜相比,磺化在36到48小时的SPPEK膜其机械力学性能好,薄膜的钒离子渗透率、离子交换容IEC、质子导电率和含水率高,且对钒离子的选择性佳,尤其价格仅为Nafion膜的1/13,是理想的Nafion膜的代替物,可望直接应用于全钒氧化还原液流（VRB）电池中。本文还讨论了磺化时间和不同磺化剂量对膜的性质的影响。     

Semi-interpenetrating polymer networks toward sulfonated poly(ether ether ketone) membranes for high concentration direct methanol fuel cell

Semi-IPNs were constructed by forming the crosslinking networks via the reaction between BPPO and diamine cross-linkers to overcome the dimensional swelling and methanol-permeation issues of SPEEK.     

Acid–base blend membranes based on 2-amino-benzimidazole and sulfonated poly(ether ether ketone) for direct methanol fuel cells

Direct methanol fuel cells (DMFC) are attractive for portable and automobile power needs, but their commercialization is hampered by high methanol permeability and the high cost of the currently used Nafion membrane. We report here a novel, low-cost blend membrane consisting of polysulfone-2-amide-benzimidazole (a basic polymer) and sulfonated poly(ether ether ketone) (an acidic polymer), which facilitates proton conduction through acid–base interactions while preserving excellent chemical and mechanical stabilities. The blend membrane exhibits performance in DMFC much higher than that of Nafion 115 and similar to that of Nafion 112, but with a remarkably superior long-term performance than Nafion 112 due to significantly reduced methanol crossover, enhancing the commercialization prospects of DMFC.     

含氨基磺化聚芳醚酮砜质子交换膜的制备与性能

通过四元缩聚的方法合成了带有氨基的磺化度可控的磺化聚芳醚酮砜共聚物(Am-SPAEKS). 采用红外光谱和核磁共振谱表征了Am-SPAEKS共聚物的结构. 该共聚物膜具有较好的热性能、尺寸稳定性、较高的质子传导率和阻醇能力. 在80℃时Am-SPAEKS-1膜的质子传导率达到0.0894 S/cm, 而其甲醇渗透系数在25℃时为0.24×10^-6 cm²/s, 低于相同温度下SPAEKS膜(0.87×10^-6 cm²/s)和Nafion膜(2×10^-6 cm²/s). 结果表明, Am-SPAEKS膜能够满足质子交换膜燃料电池(PEMFC)的使用要求.     

磺化聚醚醚酮膜的制备及其阻醇和质子导电性能

直接甲醇燃料电池 (Ｄｉｒｅｃｔｍｅｔｈａｎｏｌｆｕｅｌｃｅｌｌ,ＤＭＦＣ)以高效、清洁和燃料储运方便等优点适宜于作为各种用途的可移动动力源 ,成为 2 0世纪 90年代以来研究与开发的热点[1,2 ] .目前 ,这种电池的研究难点主要集中在催化剂不稳定和质子交换膜透醇上 .一张好的ＤＭＦＣ膜不但要可传递质子、绝缘电子 ,还应具有良好的阻醇性能 .如果膜的阻醇性能不好 ,甲醇会穿过膜到达阴极 ,与氧直接反应而不产生电流 ,不但造成燃料的浪费 ,同时也影响阴极的正常反应 ,使电池效率下降[3] .目前广泛应用于燃料电池中的Ｎａｆｉｏｎ系列膜…     

Sulfonated poly(ether ether ketone)/polyaniline composite proton-exchange membrane

Sulfonated poly(ether ether ketone) (PEEK) was prepared by sulfonation of commercial Victrex^@ PEEK and degree of sulfonation was found to be about 44.5% by ¹H NMR. Sulfonated PEEK/polyaniline composite membranes, in order to prevent methanol crossover, were prepared by chemical polymerization of a thin layer of polyaniline (PANI) in the presence of a high oxidant concentration on a single face modification. FTIR and PANI coating density studies confirmed the loading of PANI in sulfonated PEEK membrane matrix. PANI composite membranes with different polymerization time were prepared and subjected to thermogravimetric analysis as well as electrochemical and methanol permeability study to compare with sulfonated PEEK and Nafion 117 membrane. Ion-exchange capacity, water uptake, proton transport numbers and proton conductivities for different PANI composite sulfonated PEEK (SPEEK) membranes were found to be dependent on the coating density of the PANI in the membrane matrix and were slightly lower than that of Nafion 117 membrane. Methanol permeability of these membranes (especially SPEEK/PANI-1.5) was about four times lower than Nafion 117 membrane. Among the all SPEEK membranes synthesized in this study, SPEEK-1.5 appears to be more suitable for direct methanol fuel cell (DMFC) application considering optimum physicochemical and electrochemical properties, thermal stability as well as very low methanol permeability. Above all, the cost-effective and simple fabrication technique involved in the synthesis of such composite membranes makes their applicability quite attractive.     

Naphthalene‐based poly(arylene ether ketone) copolymers containing sulfobutyl pendant groups for proton exchange membranes

A new monomer 1,5‐bis(4‐fluorobenzoyl)‐2,6‐dimethoxynaphthalene (DMNF) was prepared and further polymerized to form naphthalene‐based poly(arylene ether ketone) copolymers containing methoxy groups (MNPAEKs). The side‐chain‐type sulfonated naphthalene‐based poly(arylene ether ketone) copolymers (SNPAEKs) were obtained by demethylation and sulfobutylation. Flexible and tough membranes with reasonably high mechanical strength were prepared. The SNPAEKs membrane showed anisotropic membrane swelling with larger swelling in thickness than in plane. Transmission electron microscopy (TEM) analysis revealed clear nanophase separated structure of SNPAEKs membranes, which composed of hydrophilic side chain and hydrophobic main‐chain domains. Proton conductivities of copolymers increased gradually with increase in temperature. The highest conductivity of 0.179 S/cm was obtained for SNPAEK‐80 (IEC = 1.82 mequiv/g) at 80 °C, which is higher than that of Nafion117 (0.146 S/cm). The SNPAEKs membranes exhibit the methanol permeability in the range of 3.42 × 10^?8?4.49 × 10^?7 cm²/s, which are much lower than that of Nafion117. They could be the promising materials as alternative to Nafion membrane for direct methanol fuel cells applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47:5772–5783, 2009     

磺化侧苯基杂萘联苯聚醚酮酮的合成与性能

以4-(3-苯基-4-羟基苯基)-2,3-二氮杂萘-1-酮(DHPZ-P)、 4-(4-羟基苯基)-2,3-二氮杂萘-1-酮(DHPZ)和1,4-二(4'-氟苯甲酰基)苯(BFBB)为原料, 经溶液亲核取代缩聚反应, 通过调节DHPZ-P和DHPZ的比例, 合成了一系列侧苯基杂萘联苯聚醚酮酮(PPEKK-P), 然后以浓硫酸为磺化剂, 制备出一系列磺化侧苯基杂萘联苯聚醚酮酮(SPPEKK-P). 利用傅里叶变换红外光谱(FTIR)和氢核磁共振谱(¹H NMR)对聚合物结构进行表征, 结果表明, 磺酸基团引入到聚合物链的侧苯基上. 采用溶液浇铸法制备SPPEKK-P质子交换膜. SPPEKK-P膜的吸水率、 溶胀率和质子传导率均随离子交换容量(IEC)的增加而增加, 且具有较好的耐氧化性. IEC最高的SPPEKK-P-100膜的质子传导率在95℃能达到7.44×10^-2 S/cm, 且甲醇渗透系数为5.57×10^-8 cm²/s, 阻醇性能优于Nafion117膜.     

Comparative effect of phthalazinone units in sulfonated poly(arylene ether ether ketone ketone) copolymers as proton exchange membrane materials

A new series of aromatic poly(arylene ether ether ketone ketone) copolymers containing pendant sulfonic acid groups (SPAEEKK‐D) were synthesized from commercially available monomers 1,3‐bis(4‐fluorobenzoyl)‐benzene, sodium 6,7‐dihydroxy‐2‐naphthalenesulfonate, and 4‐(4‐hydroxyphenyl)‐2,3‐phthalazin‐1‐one (DHPZ). Structure–property relationships of the phthalazinone SPAEEKK‐D series poly(arylene ether ether ketone ketone) copolymer were compared with copolymers SPAEEKK‐B and SPAEEKK‐H containing different diols such as 4,4′‐biphenol and hydroquinone, respectively, prepared in our earlier work. Ion exchange capacity (IEC_w, weight‐based; IEC_v, volume‐based), thermal stabilities, swelling, proton and methanol transport properties of the membranes were investigated in relation to their structures and compared with those of perfluorinated ionomer (Nafion 117). The SPAEEKK‐D membrane incorporating the phthalazinone monomer DHPZ showed relatively lower water uptake and methanol permeability compared with earlier SPAEEKK‐B and SPAEEKK‐H membranes incorporating biphenol and hydroquinone monomers, respectively. Inclusion of phthalazinone in the SPAEEKK‐D copolymers led to lower water absorption, enabling increased proton exchange concentrations in the hydrated polymer matrix that resulted in more desirable membrane properties for future direct methanol fuel cell applications. The SPAEEKK‐D membranes also showed improved mechanical and thermal properties and oxidative stability compared with the earlier SPAEEKK‐B and ‐H membranes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 989–1002, 2008     

Characterization and performance of proton exchange membranes for direct methanol fuel cell: Blending of sulfonated poly(ether ether ketone) with charged surface modifying macromolecule

Modification of sulfonated poly(ether ether ketone) (SPEEK) membrane was attempted by blending charged surface modifying macromolecule (cSMM). The modified membrane was tested for direct methanol fuel cell (DMFC) application; i.e. a SPEEK/cSMM blend membrane was compared to a SPEEK membrane and a Nafion 112 membrane for the thermal and mechanical stability, methanol permeability, and proton conductivity. Thermal and mechanical stability of the blended membrane were slightly reduced from the SPEEK membrane but still higher than the Nafion 112 membrane. The blend membrane was found to be promising for DMFC applications because of its lower methanol diffusivity (2.75 × 10⁻⁷ cm² s⁻¹) and higher proton conductivity (6.4 × 10⁻³ S cm⁻¹), than the SPEEK membrane. A plausible explanation was given for the favorable effect of cSMM blending.