Evaluation of Gypsum and Calcium Oxalates in Deteriorated Mural Paintings by Quantitative FTIR Spectroscopy

This study dealt with the development of a procedure based on quantitative FTIR spectroscopy to determine the amount of some contaminants in wall paintings, mortars, and stone micro‐samples. As contaminants we selected gypsum, CaSO₄ · 2H₂O, and calcium oxalate monohydrate, CaC₂O₄ · H₂O, among the most common polluting substances present in architectural porous materials. Calibration curves of absorbance versus analyte concentration were determined by adopting both the internal and external standard methods. As internal standard we used Prussian blue, Fe₃[Fe(CN)₆]₄, that presents an unique infrared peak at 2094 cm^? 1. The correlation coefficient for a linear fit was very good for every calibration, being in each case greater than 0.9900. Furthermore, the precision of the evaluation of gypsum and calcium oxalates varied in the range 8–15% and ca. 4% respectively. In order to verify the findings, some specimens, which came from real frescoes, were analysed both by DSC calorimetry and FTIR spectroscopy: we found a satisfactory match between the quantitative analyses performed by the two techniques. For the first time, the application of this method allowed the quantitative determination of the desulphatization power of the Ferroni‐Dini method—based on the ammonium carbonate and barium hydroxide technique—in the conservation of mural paintings.     

Nanoparticles of Sr(OH)<Subscript>2</Subscript>: synthesis in homogeneous phase at low temperature and application for cultural heritage artefacts

This paper concerns the synthesis and the characterization of nanometer particles of Sr(OH)₂, a moderately high water soluble hydroxide (Ksp= 3.2×10^-4 at 25 °C). The reported process yields strontium hydroxide nanoparticles starting from low cost raw materials in aqueous medium (homogeneous phase) at low temperature (below 100 °C) by chemical precipitation from salt solutions, involving very simple operational steps and avoiding the use of organic solvents. Observations by X-ray diffraction (XRD), scanning electron microscopy (SEM), electron dispersive X-Ray (EDX) and Fourier transform infrared spectroscopy (FTIR) indicate that the particles are well-crystallized and have nanometer dimensions (∼ 30 nm in diameter). Moreover, experimental evidence shows the potential use of this material for the protection and the consolidation of wall paintings (frescoes), paper, stone, wood and other artistic artefacts. PACS  81.16.Be; 82.70.Dd; 68.37.Hk; 68.37.Xy; 61.46.Df     

Stimuli-sensitive nanoparticles for multiple anti-HIV microbicides

This study is aimed to develop and evaluate an advanced intravaginal formulation for the delivery of multiple anti-HIV microbicides. Novel stimuli-sensitive nanoparticles (NPs) which protected the encapsulated drugs from being degraded in acidic pH conditions were made of Eudragit S-100^® (ES100^®), a pH-sensitive polymer. ES100^® NPs were prepared using the quasi-emulsion solvent diffusion technique and loaded with two microbicides namely Tenofovir (TNF) and Etravirine (ETV). The effects of various fabrication parameters on the formulation properties were evaluated for the optimization of ES100^® NPs. The morphology of the ES100^® NPs was examined by scanning electron microscopy. The cytotoxicity of NPs containing microbicides individually or in a combination was assessed using cell viability and trans-epithelial electrical resistance (TEER) measurements. The cellular uptake rates of the model microbicides by human vaginal epithelial cells, VK2 E6/E7 cells, were evaluated using confocal microscopy and florescence-assisted cell sorting technique. ES100^® NPs had a spherical shape, smooth surface, and uniform texture with a little aggregation. The average particle size for NPs loaded with TNF ranged from 125 to 230 nm, whereas those for ETV-loaded NPs ranged from 160 to 280 nm. ES100^® NPs had zeta potential in the range of ?5 to ?10 mV. In-vitro release studies displayed the potential benefits of ES100^® NPs in retaining and protecting the loaded microbicides at vaginal pH (acidic), but immediately releasing them as the pH changes to neutral or 7.4 (physiological pH). Cell viability studies demonstrated that ES100^® NPs did not exert any cytotoxicity individually or in a combination of both microbicides. TEER measurements confirmed that ES100^® NPs loaded with TNF and ETV did not cause any changes in the barrier integrity of VK2 E6/E7 cell monolayer. The cellular uptake study revealed that ES100^® NPs were taken by vaginal epithelial cells through the endocytosis process and that the uptake rate of the model microbicides loaded in nanoparticles was greater than that in the solution. The ES100^® NPs whose degradation rates are dependent on environmental pH would serve as an efficient platform for targeted delivery of multiple microbicides to protect women from sexually transmitted diseases including HIV-1 infection.     

Efficacy of nanolime in restoration procedures of salt weathered limestone rock

Salt crystallisation process is one of the most powerful weathering agents in stone materials, especially in the coastal areas, where sea-spray transports large amount of salts on the stone surface. The consolidation of such degraded stone material represents a critical issue in the field of restoration of cultural heritage. In this paper, the nanolime consolidation behaviour in limestone degraded by salt crystallization has been assessed. For this purpose, a stone material taken from a Sicilian historical quarry and widely used in the eastern Sicilian Baroque architecture has been artificially degraded by the salt crystallization test. Then degraded samples have been treated with NanoRestore^®, a suspension of nanolime in isopropyl alcohol. To evaluate the consolidating effectiveness, the peeling test and point load test were performed. Moreover, mercury intrusion porosimetry has been executed to evaluate the variations induced by treatment, while colorimetric measurements have been aimed to assess aesthetical issues.     

A study of smalt and red lead discolouration in Antiphonitis wall paintings in Cyprus

The present analytical study focuses on the degradation phenomena observed in fifteenth century wall paintings of the Christ Antiphonitis monastery in Cyprus. Examination of ten fragments by means of optical microscopy (OM), scanning electron microscopy (SEM/EDS), μRaman and FTIR spectroscopy revealed smalt discolouration and loss, and transformation of red lead from orange Pb₃O₄ to black PbO₂. The chromatic changes have affected the aesthetic effect of the paintings insofar as these pigments were extensively used. The mechanisms of smalt weathering, i.e. leaching of alkali and formation of micro-cracks, are interpreted in relation to its chemical composition and to the aggressive environmental conditions. In addition, it is assumed that red lead degradation may have been induced not only by the effect of temperature, light and humidity but also by the presence of chlorine salts. These phenomena of pigment alteration and loss underline the unsuitability of smalt and minium on wall paintings, regardless of the painting technique (fresco, fresco-secco, secco).     

Nanoparticles for conservation of bio-calcarenite stone

In the present study, the consolidation effectiveness of some inorganic nanoparticles dispersions (silica, calcium hydroxide, and strontium hydroxide) has been evaluated when applied on a very porous stone substrate, i.e., Lecce stone. The strengthening effect of the nanoparticle-based treatments was compared to that exhibited by the well-known consolidant tetraethoxysilane. Ca(OH)₂ and Sr(OH)₂ nanoparticles were prepared in laboratory and characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), dynamic light scattering (DLS), and Fourier transform infrared spectroscopy (FTIR). The kinetic stability of nanoparticles dispersions was determined by UV-vis spectrophotometric studies. Moreover, the study of the nanolime carbonatation process was carried out using FTIR spectroscopy. Distribution of the applied product into the stone substrate was examined by SEM-EDS. The chemical weathering effect of salt crystallization of the treated specimens was evaluated by performing the dry weight loss (DWL) test. All the results suggested that Ca(OH)₂ and Sr(OH)₂ nanoparticles, applied as 2-propanol dispersions, display some good properties as consolidating agents for a very porous bio-calcarenite such as Lecce stone.     

Nano-powders of Na0.5K0.5NbO3 made by a sol–gel method

Sodium potassium niobate (NKN) nano-particle powders were synthesised through the thermal decomposition of a sol–gel NKN precursor. Powders and gels were characterised by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and transmission electron microscopy (TEM). Hydrated carbonate phases formed as a result of reaction with evolved vapours during organic decomposition, and by reaction of NKN powders with H₂O and CO₂ on exposure to air. The primary particle size of the powders increased from <50 to <250 nm as decomposition temperatures were raised from 500 to 950 °C.     

Dustiness behaviour of loose and compacted Bentonite and organoclay powders: What is the difference in exposure risk?

Single-drop and rotating drum dustiness testing was used to investigate the dustiness of loose and compacted montmorillonite (Bentonite) and an organoclay (Nanofil^®5), which had been modified from montmorillonite-rich Bentonite. The dustiness was analysed based on filter measurements as well as particle size distributions, the particle generation rate, and the total number of generated particles. Particle monitoring was completed using a TSI Fast Mobility Particle Sizer (FMPS) and a TSI Aerosol Particle Sizer (APS) at 1 s resolution. Low-pressure uniaxial powder compaction of the starting materials showed a logarithmic compaction curve and samples subjected to 3.5 kg/cm² were used for dustiness testing to evaluate the role of powder compaction, which could occur in powders from large shipments or high-volume storage facilities. The dustiness tests showed intermediate dustiness indices (1,077–2,077 mg/kg powder) in tests of Nanofil^®5, Bentonite, and compacted Bentonite, while a high-level dustiness index was found for compacted Nanofil^®5 (3,487 mg/kg powder). All powders produced multimodal particle size-distributions in the dust cloud with one mode around 300 nm (Bentonite) or 400 nm (Nanofil^®5) as well as one (Nanofil^®5) or two modes (Bentonite) with peaks between 1 and 2.5 μm. The dust release was found to occur either as a burst (loose Bentonite and Nanofil^®5), constant rate (compacted Nanofil^®5), or slowly increasing rate (compacted Bentonite). In rotating drum experiments, the number of particles generated in the FMPS and APS size-ranges were in general agreement with the mass-based dustiness index, but the same order was not observed in the single-drop tests. Compaction of Bentonite reduced the number of generated particles with app. 70 and 40% during single-drop and rotating drum dustiness tests, respectively. Compaction of Nanofil^®5 reduced the dustiness in the single-drop test, but it was more than doubled in the rotating drum test. Physically relevant low-pressure compaction may reduce the risk of particle exposure if powders are handled in operations with few agitations such as pouring or tapping. Repeated agitation, e.g., mixing, of these compacted powders, would result in reduced (app. 20% for Bentonite) or highly increased (app. 225% for Nanofil^®5) dustiness and thereby alter the exposure risk significantly.     

Effects of different precipitants on LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> for lithium ion batteries prepared by modified co-precipitation method

Effects of two different precipitants of Na₂CO₃ and Na₂C₂O₄ on LiNi_0.5Mn_1.5O₄ (LNMO) cathode materials, which are prepared by a modified co-precipitation method, have been investigated. Various measurements have been applied to characterize the physical and electrochemical performances of LNMO. Compared with the LNMO prepared by the oxalate co-precipitation (LNMO2), the material synthesized by the carbonate co-precipitation (LNMO1) not only shows more uniform porosity and smaller particles but also has a better rate capability and cycling performance. In addition, the sample prepared by carbonate has a stable spherical structure, due to the fact that carbonate co-precipitation with less gas release during calcination can prevent the destruction of the as-prepared LNMO material structure and promote the formation of regular particle and aperture. Based on the electrochemical test results, LNMO1 shows greatly enhanced electrochemical performance of a high initial discharge capacity of 125.6 mAh g^?1 at 0.25 °C, as well as a preferably capacity retention of 96.5% after 100 cycles at 0.5 °C. And even at a high rate of 10 °C, the discharge capacity of LNMO1-based cell still approaches 83.1 mAh g^?1.     

Estimation of carbonate concentration and characterization of marine sediments by Fourier Transform Infrared Spectroscopy

Fourier Transform Infrared Spectroscopy (FTIR) is a well established method for the characterization of mineralogical and geochemical properties of marine sediments. Understanding the biogeochemical changes in marine ecosystems is challenging task since it requires adequate analytical techniques and efforts. Biogeochemical characteristics of twenty one marine sediment samples collected off Chennai coast, Bay of Bengal, India were analyzed using FTIR spectroscopy. The FTIR peaks at 1460 cm⁻¹ (stretching vibration) and 880 cm⁻¹ (bending vibration) were used for carbonate determination. To verify the FTIR results, the obtained carbonate data were compared with carbonate values obtained by chemical analyses. The ranges of carbonate in sediments using FTIR and chemical analyses were 4.5–9.6% and 4.8–10%, respectively. The significant positive relationship was obtained between the carbonate results of FTIR and chemical analyses. This study demonstrates that instead of expensive and time consuming chemical methods, FTIR spectroscopic technique is found as a suitable, rapid and effective method for the quantification of carbonate in marine sediments.     

Alpha decay of the new isotope 174Hg

Neutron deficient mercury isotopes were produced in the reaction ³⁶Ar + ¹⁴⁴Sm using bombarding energies of 180–230 MeV. Fusion products were separated in-flight from the primary beam using a gas-filled recoil separator. An alpha line with the alpha particle energy and half-life of (7069±11) keV and (2.1 _?0.7 ^+1.8 ) ms, respectively, was assigned to the new mercury isotope ¹⁷⁴Hg.     

Determination of Epinephrine in Pharmaceutical Formulation by an Optimized Novel Luminescence Method Using CdS Quantum Dots as Sensitizer

In this article, a novel chemiluminescence method using water-soluble CdS quantum dots (QDs) as sensitizers is proposed for the chemiluminometric determination of epinephrine. The method is based on the quenching effect of epinephrine on the chemiluminescence emission generated by the mixing of CdS quantum dots (QDs) with hydrogen carbonate (HCO₃ ^-) in the presence of hydrogen peroxide (H₂O₂) in an alkaline medium. The optimization of variables influencing the chemiluminescence response of the method has been carried out by using experimental design. Under the optimal conditions, there is good linear relationship between the relative chemiluminescence intensity and the concentration of epinephrine over the range of 5?×?10^?9–1?×?10^?6?molL^?1 with a 3σ detection limit of 5?×?10^?11?molL^?1. The method has been successfully applied to the determination of epinephrine in pharmaceutical formulation and the recovery test was done in human urine.     

Effect of variation of different nanofillers on structural,electrical, dielectric,and transport properties of blend polymer nanocomposites

In the present work, the effect of various nanofillers with different particle sizes and dielectric constants (BaTiO₃, CeO₂, Er₂O₃, or TiO₂) on blend solid polymer electrolyte comprising PEO and PVC complexed with bulky LiPF₆ has been explored. The XRD analysis confirms the polymer nanocomposite formation. FTIR provides evidence of interaction among the functional groups of the polymer with the ions and the nanofiller in terms of shifting and change of the peak profile. The highest ionic conductivity is ~?2.3?×?10^?5 S cm^?1 with a wide electrochemical stability window of ~?3.5 V for 10 wt% Er₂O₃. The real and imaginary parts of dielectric permittivity follow the identical trend of the decreasing value of dielectric permittivity and dielectric loss with increase in the frequency. The particle size and the dielectric constant show an abnormal trend with different nanofillers. The AC conductivity follows the universal Jonscher power law, and an effective mechanism has been proposed to understand the nanofiller interaction with cation coordinated polymer.     

Poly (ethylene oxide) (PEO)-based,sodium ion-conducting‚ solid polymer electrolyte films,dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> filler,for applications in sodium ion cells

The studies on solid polymer electrolyte (SPE) films with high ionic conductivity suitable for the realization of all solid-state Na-ion cells? form the focal theme of the work presented in this paper. The SPE films are obtained by the solution casting technique using the blend solution of poly (ethylene oxide) (PEO) with ethylene carbonate (EC) and propylene carbonate (PC) and complexed with sodium nitrate. Structural and thermal studies of SPE films are done by XRD, FTIR spectroscopy, and TGA techniques. Surface morphology of the films is studied using the FESEM. The ionic conductivity of SPE films is determined from the electrochemical impedance spectroscopy studies. For the SPE film with 16 wt% of NaNO₃ used for reacting with the polymer blend of PEO with EC and PC, the ionic conductivity obtained is around 1.08 × 10^?5 S cm^?1. Addition of the Al₂O₃ as the filler material is found to enhance the ionic conductivity of the SPE films. The studies on the Al₂O₃ modified SPE film show an ionic conductivity of 1.86 × 10^–4 S cm^?1, which is one order higher than that of the SPE films without the filler content. For the SPE film dispersed with 8 wt% of Al₂O₃, the total ion transport number observed is around 0.9895, which is quite impressive from the perspective of the applications in electrochemical energy storage devices. From the cyclic voltammetry studies, a wide electrochemical stability window up to 4 V is observed, which further emphasizes the commendable electrochemical behavior of these SPE films.     

Synthesis and characterization of nanocrystalline HAp powders prepared by using aloe vera plant extracted solution

Nanocrystalline hydroxyapatite (HAp) powders were synthesized by a simple method using aloe vera plant extracted solution. To obtain nanocrystalline HAp, the prepared precursor was calcined in air at 400–800 °C for 2 h. The phase composition of the calcined samples was studied by X-ray diffraction (XRD) technique. The XRD results confirmed the formation of HAp phase. With increasing calcination temperature, the crystallite of the HAp increased, showing the hexagonal structure of HAp with the lattice parameter, a, in a range of 0.9520–0.9536 nm and c of 0.6739–0.6928 nm. The particle sizes of the powder were obtained to be 43–171 nm. The optical properties of the calcined powders were characterized by Raman and FTIR spectroscopies. The Raman spectra showed a main peak of the phosphate vibration mode (ν₁(PO₄)) at ∼963 cm⁻¹ for all the calcined samples. The peaks of the phosphate carbonate and hydroxyl vibration modes were observed in the FTIR spectra for all the calcined powders. The morphology tends to change from a spherical shape to a rod-like shape with increasing calcination temperature as revealed by TEM.     

Investigation on (EC/DMC)(70−x)wt% to LiBETI(x)wt% impact on PVdF-co-HFP/octadecylamine-MMT(montmorillonite) nano clay composite electrolytes

The composition dependence of plasticizer (ethylenecarbonate(EC)/dimethyl carbonate(DMC))_(70?x)wt% to Lithium bis(perfluoroethanesulfonyl)imide(LIBETI)_(x)wt% salt (where x?=?1.5, 3.0, 4.5, 6.0 wt%) on PVdF-co-HFP (25 wt%)/surface modified octadecylamine containing montmorrillonite (ODA-MMT) nano clay (5 wt%) matrix has been investigated by AC impedance, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dielectric and cyclic voltammetry studies. The enhanced conductivity 2.1?×?10^?5 Scm^?1 is noted in salt rich phase (EC/DMC)_(70–6)wt% /LiBETI_(x=6)wt% (VK4). In XRD, 2θ at 20.9° confirms β-phase. In FTIR studies, vibrational bands 838, 522 and 611 cm^?1 confirm β-phase of PVdF due to clay intercalation. In DSC studies, the melting of α-phase crystallites is noted between 140–150 °C. In SEM studies, one of the membranes presents fern leaf texture confirming swelling of clay. The increase in dielectric constant and dielectric loss with decrease in frequency is attributed to high contribution of charge accumulation at the electrode–electrolyte interface. In cyclic voltammetry studies, salt-rich phase membrane (VK4) shows good cyclability than other membranes.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Synthesis and Raman spectroscopic characterisation of hydrotalcite with CO32− and VO3− anions in the interlayer

Infrared and Raman spectroscopy were used to characterise synthetic mixed carbonate and vanadate hydrotalcites of formula Mg₆Al₂(OH)₁₆(CO₃)²⁻, (VO₄)³⁻·4H₂ O. The spectra were used to assess the molecular assembly of the cations and anions in the hydrotalcite structure. The spectra may be conveniently subdivided into spectral features based on (1) the carbonate anion (2) the hydroxyl units and (3) water units. Bands were assigned to the hydroxyl stretching vibrations of water. Three types of carbonate anions were identified: (1) carbonate hydrogen‐bonded to water in the interlayer, (2) carbonate hydrogen‐bonded to the hydrotalcite hydroxyl surface and (3) free carbonate anions. It is proposed that the water is highly structured in the hydrotalcite, as it is hydrogen‐bonded to both the carbonate and the hydroxyl surface. The spectra were used to assess the contamination of carbonate in an open reacting vessel in the synthesis of vanadate hydrotalcites of formula Mg₆Al₂(OH)₁₆(CO₃)²⁻, (VO₄)³⁻·4H₂ O. Bands have been assigned to vanadate anions in the infrared and Raman spectra associated with V O bonds. Copyright © 2007 John Wiley & Sons, Ltd.     

Ultrasonic-assisted production of precipitated calcium carbonate particles from desulfurization gypsum

This study aimed to investigate the effect of ultrasonic application on the production of precipitated calcium carbonate (PCC) particles from desulfurization gypsum via direct mineral carbonation method using conventional and venturi tube reactors in the presence of different alkali sources (NaOH, KOH and NH₄OH). The venturi tube was designed to determine the effect of ultrasonication on PCC production. Ultrasonic application was performed three times (before, during, and after PCC production) to evaluate its exact effect on the properties of the PCC particles. Scanning electron microscope (SEM), X-ray diffraction (XRD), Atomic force microscope (AFM), specific surface area (SSA), Fourier transform infrared spectrometry (FTIR), and particle size analyses were performed. Results revealed the strong influence of the reactor types on the nucleation rate of PCC particles. The presence of Na⁺ or K⁺ ions in the production resulted in producing PCC particles containing only calcite crystals, while a mixture of vaterite and calcite crystals was observed if NH₄⁺ ions were present. The use of ultrasonic power during PCC production resulted in producing cubic calcite rather than vaterite crystals in the presence of all ions. It was determined that ultrasonic power should be conducted in the venturi tube before PCC production to obtain PCC particles with superior properties (uniform particle size, nanosized crystals, and high SSA value). The resulting PCC particles in this study can be suitably used in paint, paper, and plastic industries according to the ASTM standards.     

An Infrared Method,with Reduced Solvent Consumption,for the Determination of Chlorsulfuron in Pesticide Formulations

A simple method has been developed for the determination of Chlorsulfuron in pesticide formulations by Fourier Transform Infrared (FTIR). Samples were diluted with CHCl_3^? , and the FTIR spectra of the samples and standards were obtained at a nominal resolution of 4 cm^? 1 from 4000 to 900 cm^? 1 with the accumulation of 25 scans. Chlorsulfuron determination was based on the measurement of peak area values from 1373 to 1363 cm^? 1 which were corrected by use of a two points baseline defined from 1401 to 1302 cm^? 1. The limit of detection achieved, which was of the order of 6 µg g^? 1, was appropriate for the determination of Chlorsulfuron in commercially available formulations. FTIR results were statistically comparable with those found by High Performance Liquid Chromatography (HPLC). The procedure reduces organic solvent consumption per sample to less than 3 ml CHCl₃, reduces waste generation and increases the sample measurement frequency up to 60 h^? 1.