p-GaN插入层调控InGaN基黄绿双波长LED发光光谱

采用MOCVD技术在硅衬底上生长了含有7个黄光量子阱和1个绿光量子阱的混合有源区结构的InGaN基黄绿双波长LED外延材料,研究了电子阻挡层前p-GaN插入层厚度对黄绿双波长LED载流子分布及外量子效率(EQE)的影响。通过LED变温电致发光测试系统对LED光电性能进行了表征。结果表明,100 K小电流时随着电流密度的增大,三组样品的绿光峰与黄光峰相对强度的比值越来越大,且5.5 A·cm^-2的电流密度下,随着温度从300 K逐步降低至100 K,三组样品的绿光峰与黄光峰相对强度的比值也越来越大,说明其载流子都在更靠近p型层的位置发生辐射复合。三组样品的p-GaN插入层厚度为0,10,30 nm时,EQE峰值依次为29.9%、29.2%和28.2%,呈现依次减小的趋势,归因于p-GaN插入层厚度越大,p型层越远离有源区,空穴注入也越浅。电子阻挡层前p-GaN插入层可以有效减小器件EL光谱中绿光峰随着电流密度增加时峰值波长的蓝移(33 nm),实现了对低温发光光谱的调控。     

量子阱生长气压对InGaN/GaN黄光LED光电性能的影响

采用MOCVD技术在图形化硅衬底上生长了InGaN/GaN多量子阱黄光LED外延材料,研究了不同的量子阱生长气压对黄光LED光电性能的影响。使用高分辨率X射线衍射仪（HRXRD）和荧光显微镜（FL）对晶体质量进行了表征,使用电致发光系统积分球测试对光电性能进行了表征。结果表明：随着气压升高,In的并入量略有降低且均匀性更好,量子阱中的点缺陷数目降低,但是阱垒间界面质量有所下降。在实验选取的4个气压4,6.65,10,13.3 kPa下,外量子效率最大值随着量子阱生长气压的上升而显著升高,分别为16.60%、23.07%、26.40%、27.66%,但是13.3 kPa下生长的样品在大电流下EQE随电流droop效应有所加剧,在20 A·cm^-2的工作电流下,样品A、B、C、D的EQE分别为16.60%、19.77%、20.03%、19.45%,10 kPa下生长的量子阱的整体光电性能最好。     

Effect of Barrier Temperature on Photoelectric Properties of Ga N-Based Yellow LEDs

The effect of growth temperature of barriers on photoelectric properties of Ga N-based yellow light emitting diodes(LEDs) is investigated. It is found that as the barrier temperature increases, the crystal quality of multiquantum wells(MQWs) and the quality of well/barrier interface are improved, and the quantum well is thermally annealed, so that the indium atoms in the quantum well migrate to the equilibrium position, reducing the phase separation of the quantum well and improving the crystal quality of quantum wells(QWs). However, the external quantum efficiency(EQE) of the samples begins to decrease when raising the barrier temperature even further.One explanation may be that the higher barrier temperature destroys the local state in the quantum well and reduces the well/barrier interface quality. Therefore, a suitable barrier temperature is proposed, contributing to the improvement of the luminous efficiency of the yellow LEDs.     

纳米折叠InGaN/GaN LED材料生长及器件特性

在以自组织Ni纳米岛为掩膜制作的n-GaN纳米柱上,利用MOCVD方法外延生长了具有折叠InGaN/GaN多量子阱(MQW)的LED结构外延片,进而制作了LED器件.外延片上中下游的光致荧光测试,结果表明外延片具有很好的均匀性.用该外延片制作的LED的电致发光谱,随注入电流增加没有明显蓝移,这表明纳米结构能更好地释放应力,纳米柱上外延生长的多量子阱,具有较低的压电极化电场.正向工作电流20 mA时,LED器件的工作电压为4.6 V. 关键词： 纳米柱LED 光致发光 电致发光     

Improved electroluminescence on nonpolar m ‐plane InGaN/GaN quantum wells LEDs

Improved nonpolar m ‐plane light emitting diodes (LEDs) with a thick InGaN multi‐quantum‐well (MQW) structure have been fabricated on low extended defect bulk m ‐plane GaN substrates using metal organic chemical vapor deposition (MOCVD). The peak wavelength of the electroluminescence emission from the packaged LEDs was 402 nm, which is in the blue‐violet region. The output power and EQE were 28 mW and 45.4%, respectively, at a pulsed driving current of 20 mA. With increasing current, the output power increased linearly, and fairly flat EQE was observed with increasing drive current. At 200 mA, the power and EQE were 250 mW and 41%, respectively. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Controlling the defect density to improve the output power of InGaN/GaN-based vertical light-emitting diodes by using substrates patterned with SiO2 lenses

In this study, we investigated the effect of SiO₂ lenses on the output power of InGaN/GaN-based vertical light-emitting diodes (VLEDs; wavelength = 445 nm) and compared the results to those of reference VLEDs without the SiO₂ lenses (planar samples). Arrays of SiO₂ lenses (pitch = 3 μm, width = 2.5 μm, height = 1.0 μm) were formed on c-plane sapphire substrates. The external quantum efficiency (EQE) of the packaged VLEDs with planar and patterned substrates was characterised. At 5 mA, the EQE of the patterned samples was 150% higher than that of the planar samples. A patterned, N-polar, n-GaN sample contained far fewer nanopipes (approximately 2.2 × 10⁵ cm^?2) than a planar n-GaN sample (approximately 2.4 × 10⁶ cm^?2). Furthermore, the patterned samples contained far fewer threading dislocations (approximately 1.0 × 10⁸ cm^?2) than the planar samples (approximately 5.0 × 10⁸ cm^?2). Scanning electron microscopy (SEM) images showed that the photoelectrochemical (PEC)-etched patterned samples contained cones that were 150% larger than that of the PEC-etched planar samples. In addition, SEM images, cathode luminescence measurements and finite-difference time-domain simulations were used to characterise the improved light output of the patterned samples.     

Cesium lead halide perovskite quantum dot-based warm white light-emitting diodes with high color rendering index

White light-emitting diodes (WLEDs) were fabricated by employing a combination of a commercial yellow emission Ce³⁺-doped Y₃Al₅O₁₂ (YAG:Ce)-based phosphor and all-inorganic perovskite quantum dots pumped with blue LED chip. Perovskite quantum dot solution was used as the color conversion layer with liquid-type structure. Red-emitting materials based on cesium lead halide (CsPb(X)₃) perovskite quantum dots were introduced to generate WLEDs with high efficacy and high color rendering index through compensating the red emission of the YAG:Ce phosphor-based commercialized WLEDs. The experimental results suggested that the luminous efficiency and color rendering index of the as-prepared WLED device could reach up to 84.7 lm/W and 89, respectively. The characteristics of those devices including correlated color temperature (CCT), color rendering index (CRI), and color coordinates were observed under different forward currents. The as-fabricated warm WLEDs showed excellent color stability against the increasing current, while the color coordinates shifted slightly from (0.3837, 0.3635) at 20 mA to (0.3772, 0.3592) at 120 mA and color temperature tuned from 3803 to 3953 K.     

Optical properties of GaN/AlN multiple quantum wells

Optical properties of GaN/AlN multiple quantum wells (MQW) have been investigated by Raman scattering, photoluminescence and photoluminescence excitation measurements. A careful examination of the Raman spectrum reveals the fact that the constituent layers of GaN/AlN MQWs are well strained. The experimental results of emission and absorption in MQWs were compared with the calculated solutions of the finite quantum well and the bound states involved in the optical transitions were identified. It is found that the interband transitions up to n=3 bound state can be observed in the strained GaN/AlN MQWs sample. The temperature dependence of the heavy-hole transitions shows an interesting phenomenon, in which the peak energy first increases with increasing temperature and then decreases with the temperature rapidly. The observation can be explained in a consistent way by the strain effects of lattice mismatch due to the interplay between the thermal expansion of GaN and AlN layers. Our results indicate that pseudomorphic GaN/AlN MQWs with good quality can be readily grown, and their applications in optoelectronics can be expected in the near future.     

Effects of a prestrained InGaN interlayer on the emission properties of InGaN/GaN multiple quantum wells in a laser diode structure

The electroluminescence (EL) and photoluminescence (PL) spectra of InGaN/GaN multiple quantum wells (MQWs) with a prestrained InGaN interlayer in a laser diode structure are investigated. When the injection current increases from 5 mA to 50 mA, the blueshift of the EL emission peak is 1 meV for the prestrained sample and 23 meV for a control sample with the conventional structure. Also, the internal quantum efficiency and the EL intensity at the injection current of 20 mA are increased by 71% and 65% respectively by inserting the prestrained InGaN interlayer. The reduced blueshift and the enhanced emission are attributed mainly to the reduced quantum-confined Stark effect (QCSE) in the prestrained sample. Such attributions are supported by the theoretical simulation results, which reveal the smaller piezoelectric field and the enhanced overlap of electron and hole wave functions in the prestrained sample. Therefore, the prestrained InGaN interlayer contributes to strain relaxation in the MQW layer and enhancement of light emission due to the reduction of QCSE.     

Growth and characterization of strain-compensated InGaAs/GaAsSb type II multiple quantum wells on InP substrate

Strain-compensated InGaAs/GaAsSb type II multiple quantum wells (MQWs) were grown by molecular beam epitaxy (MBE) and their optical and electrical properties were studied. High-quality strain-compensated type II MQWs were successfully grown, which have longer emission wavelength than that of lattice-matched type II MQWs. PL peak energy at 300 K of the strain-compensated type II MQWs, where the InGaAs layer has 0.6% tensile strain and GaAsSb layer has 0.6% compressive strain, shows a red-shift of 43 meV, which is 12 meV larger than the calculated energy shift of 31 meV. In addition, the PL intensity and the electron mobility of the strain-compensated MQWs are comparable to those of the lattice-matched MQWs, suggesting that the crystal quality of the strain-compensated MQWs is good and are very promising for low dark current photodiodes in the 2 μm wavelength region.     

Negatively charged excitons and the optical properties of modulation-doped quantum wells

Optical and magneto-optical properties are studied for II-VI semiconductor multiple quantum wells (MQWs) doped with donors in the barriers to give electron concentrations of 2 10¹⁰ to 6 10¹¹ cm^-2 in the well layers. Following on from the recent identification of negatively charged excitons X^- (two electrons bound to one hole) in CdTe/Cd_1-xZn_xTe MQWs, this paper presents more specifically the circular polarisation of the luminescence associated with X^- and with the normal exciton X (one electron and one hole) in this type of structure. Very similar magneto-optical properties are observed for modulation doped Zn_0.9Cd_0.1Se/ZnSe MQWs, and X^- is identified in these wells with a binding energy as large as 7 meV for the second electron at 50Å, well-width.     

利用选择性外延法生长单芯片双波长白光InGaN/GaN多量子阱结构

为了制备单芯片无荧光粉白光InGaN/GaN多量子阱发光结构,利用选择性外延生长法在SiO2条纹掩膜板上生长出具有梯形形貌的GaN微面结构,并在该GaN微面结构上生长InGaN/GaN多量子阱结构,最终在单芯片上获得了双波长发光.结果表明:梯形GaN微面由(0001)和(11-22)面组成,两者的表面能和极性不同,并且在InGaN/GaN多量子阱生长过程中,In原子和Ga原子迁移速率不同,从而使得(0001)和(11-22)面上的多量子阱具有不同的发光波长;该性质可以使(11-22)面的微面量子阱发出蓝光(峰值波长为420nm),而(0001)面的量子阱发出黄光(峰值波长为525nm),最终形成双波长的复合白光外延结构.     

High power and high efficiency green light emitting diode on free‐standing semipolar (11$ \bar 2 $2) bulk GaN substrate

We demonstrate a high power green InGaN/GaN multiple‐quantum‐well (MQW) light emitting diode (LED) with a peak emission wavelength of 516 nm grown on low extended defect density semipolar (11 2) bulk GaN substrate by metal organic chemical vapor deposition. The output power and external quantum efficiency (EQE) at drive currents of 20 and 100 mA under direct current (DC) operation were 5.0 mW, 10.5% and 15.6 mW, 6.3%, respectively. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

一种高电流密度下效率不降低的绿光有机电致发光器件

为了提高有机电致发光器件(OLED)在高电流密度下的发光效率, 在以C545T掺杂Alq₃为发光层的有机小分子绿光器件中的发光层与电子传输层之间插入超薄LiF绝缘层.结果表明, 器件的外量子效率随着电流密度的增加始终没有降低, 直至600 mA/cm²时达到最大值 4.79%, 是相同电流密度下的参考器件的外量子效率的7倍.     

反应磁控溅射ZnO/MgO多量子阱的光致荧光光谱分析

采用反应射频磁控溅射方法，在Si(001)基片上制备了具有高c轴择优取向的ZnO/MgO多量子阱.利用X射线反射、X射线衍射、电子探针，光致荧光光谱等表征技术，研究了ZnO/MgO多量子阱的结构、成份和光致荧光特性.研究结果表明，多量子阱的调制周期在1.85—22.3 nm之间，所制备的多量子阱具有量子限域效应，导致了室温光致荧光峰的蓝移，并观测到了量子隧穿效应引起的荧光效率下降.建立了基于多声子辅助激子复合跃迁理论的室温光致荧光光谱优化拟合方法，通过室温光致荧光光谱拟合发现，ZnO/MgO比ZnO/ZnMgO多量子阱具有更大的峰位蓝移，探讨了导致光致荧光光谱展宽的可能因素. 关键词： ZnO/MgO 多量子阱 磁控溅射 光致荧光 量子限域效应     

MOVPE Growth and Fabrication of 1.3μm High Power InGaAsP-InP Polarization-Insensitive Superluminescent Diodes with Complex Strained Quantum Wells

High power polarization-insensitive InGaAsP-InP multiple quantum well (MQW) superluminescent diodes (SLD's) emitting at 1.3μm were investigated. A combination of tensile strained and compressively strained quantum wells called complex strained MQW were used in a single active layer in order to obtain polarization insensitivity. Low-pressure metalorganic chemical vapor phase epitaxy was used for crystal growth. High resolution X-ray diffraction and photoluminescence spectra showed excellent crystal quality. The SLD's were fabricated to ridge waveguide structure with 7° tilted cavity, the two facets were coated with two layers anti-reflection TiO₂/SiO₂ films, residual facet reflectivity was found to be less than 0.04%. The SLD's exhibited a up to 18.8 mW optical output power and less than 1 dB polarization dependence of output power with a less than 0.5 dB optical spectra modulation at 250 mA.     

Electroluminescence enhancement in ultraviolet organic light‐emitting diode with graded hole‐injection and ‐transporting structure

Electroluminescent intensity and external quantum efficiency (EQE) in ultraviolet organic light‐emitting diodes (UV OLEDs) have been remarkably enhanced by using a graded hole‐injection and ‐transporting (HIT) structure of MoO₃/N,N ′‐bis(naphthalen‐1‐yl)‐N,N ′‐bis(phenyl)‐benzidine/MoO₃/4,4′‐bis(carbazol‐9‐yl)biphenyl (CBP). The graded‐HIT based UV OLED shows superior short‐wavelength emis‐ sion with spectral peak of ～410 nm, maximum electroluminescent intensity of 2.2 mW/cm² at 215 mA/cm² and an EQE of 0.72% at 5.5 mA/cm². Impedance spectroscopy is employed to clarify the enhanced hole‐injection and ‐transporting capacity of the graded‐HIT structure. Our results provide a simple and effective approach for constructing efficient UV OLEDs. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Al(x)Ga(1-x)N-based deep-ultraviolet 320×256 focal plane array

We report the synthesis, fabrication, and testing of a 320×256 focal plane array (FPA) of back-illuminated, solar-blind, p-i-n, Al(x)Ga(1-x)N-based detectors, fully realized within our research laboratory. We implemented a pulse atomic layer deposition technique for the metalorganic chemical vapor deposition growth of thick, high-quality, crack-free, high Al composition Al(x)Ga(1-x)N layers. The FPA is hybridized to a matching ISC 9809 readout integrated circuit and operated in a SE-IR camera system. Solar-blind operation is observed throughout the array with peak detection occurring at wavelengths of 256 nm and lower, and falling off three orders of magnitude by ~285 nm. By developing an opaque masking technology, the visible response of the ROIC is significantly reduced; thus the need for external filtering to achieve solar- and visible-blind operation is eliminated. This allows the FPA to achieve high external quantum efficiency (EQE); at 254 nm, average pixels showed unbiased peak responsivity of 75 mA/W, which corresponds to an EQE of ~37%. Finally, the uniformity of the FPA and imaging properties are investigated.     

Influence of cracks generation on the structural and optical properties of GaN/Al0.55Ga0.45N multiple quantum wells

Both cracked and crack-free GaN/Al_0.55Ga_0.45N multiple quantum wells (MQWs) grown on GaN template by metalorganic chemical vapor deposition have been studied by triple-axis X-ray diffraction, grazing-incidence X-ray reflectivity, atomic force microscope, photoluminescence spectroscopy and low-energy positron annihilation spectroscopy. The experimental results show that cracks generation not only deteriorates the surface morphology, but also leads to a period dispersion and roughens the interfaces of MQWs. The mean density of dislocations in MQWs, determined from the average full-width at half-maximum of ω-scan of each satellite peak, has been significantly enhanced by the cracks generation. Furthermore, the measurement of annihilation-line Doppler broadening reveals a higher concentration of negatively charged vacancies in the cracked MQWs. The combination of these vacancies and the high density of edge dislocations are assumed to contribute to the highly enhanced yellow luminescence in the cracked sample.     

Research on phosphor-conversion laser-based white light used as optical source of VLC and illumination

Visible light communication (VLC) based on light emitting diodes (LEDs) or laser diodes (LDs) has attracted considerable interest in recent years. Due to the advantages of laser diodes based on nitrides, such as small size, high brightness, visible light and high bandwidth, it can be applied to illumination and communication at the same time. In this paper, blue laser and yellow phosphors were employed to synthesize white light. And “efficiency droop” is not observed in the LIV characteristics of LD-based white light either. The bandwidth measurement system with high reliability was set up. The bandwidth of blue laser diode and phosphor-conversion laser-based white light was measured. The maximum of optical ?3 dB bandwidth of blue LD is around 1.8 GHz at 80 mA and maximum of optical ?3 dB bandwidth of white light is about 1.3 GHz at 60 mA. The color parameters of the synthetic white light were characterized through integrating sphere. Moreover the trends of test data with injection current were analyzed in detail. The problem of thermal degradation of yellow phosphors has been improved by a special design that can keep a certain distance between the blue laser diode and phosphors. The experiment results verified that laser diodes based on nitrides have promising applications in lighting and communications.