Near-infrared nonmetal atomic emission from a helium microwave-induced plasma: element ratio determinations

The utility of near-infrared atomic emission lines of C, F, S, Cl and Br for the determination of element ratios in organic compounds is evaluated. An atmospheric-pressure helium microwave-induced plasma is used to fragment sample molecules and excite their constituent atoms. The effects of plasma operating parameters such as power and flow rate, as well as the effects of spatial viewing position and plasma length are also investigated.     

Study of a Low-Powered He Microwave-Induced Plasma for Determination of P, Cl, Br, and I by Atomic Emission Spectrometry

Aqueous sample solutions were nebulized by an ultrasonic nebulizer and the solvent was removed by a desolvation apparatus before introduction of the aerosol into the microwave-induced plasma (MIP). The desolvation system consists of a heating tube and a condenser associated with a concentrated H₂SO₄ desiccator. The water vapor was removed almost completely with the desolvation system. The detectability of microwave-induced plasma atomic emission spectrometry was therefore improved. The detection limits for P, Cl, Br, and I were 0.0045, 0.12, 0.23. and 0.06 μg/ml, respectively. Based on a study of the emission spectra of P, Cl, Br, and I in the range of 200 to 600 nm in He MIP, the optimum analytical lines for determination of corresponding elements were chosen.     

Determination of fluorine, chlorine, bromine and iodine by barrier discharge radiofrequency helium plasma.

A determination method of fluorine (F), chlorine (Cl), bromine (Br) and iodine (I) by a barrier discharge radiofrequency helium plasma-atomic emission spectroscopy was developed. A borosilicate glass was wrapped by two copper film electrodes, one of which was earthed, and the other was supplied with a radiofrequency high voltage (98 kHz, 3.2 kV), resulting in a discharge inside of the tube. An optical emission from the discharge tube was introduced to a charge-coupled device (CCD)-spectrometer through an optical fiber, and was monitored in the wavelength range of 730-960 nm. The emission lines of F (733.2 nm, 739.9 nm), Cl (833.3 nm, 837.6 nm, 858.6 nm, 894.8 nm, 912.1 nm, etc.), Br (827.2 nm, 882.5 nm, 889.8 nm, 926.5 nm, etc.) and I (905.8 nm) were observed. The linearity of the calibration was determined for F and Cl over the range of 1-10 microg, and for Br of 0.1-1 microg. The relative emission intensity was in the order of Br > I > Cl >F.     

A helium inductively coupled plasma for atomic emission spectrometry

An annular helium inductively coupled plasma (He ICP) was generated at atmospheric pressure. No external cooling was used to stabilize the plasma. Aqueous solution was injected into the plasma without any difficulty. Preliminary results revealed that the annular He ICP was capable of exciting elements such as Cl and Br which possess high excitation energies. Atomic emission detection limits for Cl and Br were improved by factors of 63 and 34, respectively, as compared to the results obtained from the argon inductively coupled plasma. The excitation temperature of the annular He ICP (4180 K) was less than that of an Ar ICP (5570 K).     

Optical emission spectroscopy with a microwave-induced plasma in a sealed microtube

A microwave system is used to induce a plasma inside a sealed microtube containing a sample or standard, and the emission from the analyte is measured. The detection limits are about 4 ng for S, Cl and Br, and 100 ng for Cd and Sn, in approximately 30-mul samples. Both gaseous and liquid samples can be analysed.     

Evaluation of sample preparation methods for elastomer digestion for further halogens determination

In this work, three sample preparation methods were evaluated for further halogen determination in elastomers containing high concentrations of carbon black. Samples of nitrile-butadiene rubber, styrene-butadiene rubber, and ethylene-propylene-diene monomer elastomers were decomposed using oxygen flask combustion and microwave-induced combustion (MIC) for further Br and Cl determination by ion chromatography (IC), inductively coupled plasma optical emission spectrometry (ICP OES), and inductively coupled plasma mass spectrometry (ICP-MS). Extraction assisted by microwave radiation in closed vessels was also evaluated using water or alkaline solution. Digestion by MIC was carried out using 50 mmol l⁻¹ (NH₄)₂CO₃ as the absorbing solution. The effect of the reflux step was also evaluated. Accuracy was evaluated using certified reference materials with polymeric matrix composition and by comparison of results using neutron activation analysis. Agreement for Br and Cl was better than 95% by MIC using 5 min of reflux, and no statistical difference was found using IC, ICP OES, and ICP-MS for determination of both analytes. For MIC, the relative standard deviation (RSD) was lower than 5%. Using extraction in closed vessels, a high amount of residues was observed, and recoveries were lower than 45% for both analytes. For oxygen flask combustion, the agreement was similar using MIC but RSD was higher (20%). The residual carbon content, an important parameter used to evaluate the digestion efficiency, was always below 1% for MIC. Using MIC, it was possible to digest elastomers with high efficiency, resulting in a single solution suitable for halogen determination by different techniques.     

Determination of halides by microwave induced plasma and stabilized capacitive plasma atomic emission spectrometry after on-line continuous halogen generation

This paper describes a comparative study of the microwave induced plasma (MIP) and the stabilized capacitive plasma (SCP) for halide determinations. The MIP is generated in a Beenakker cavity TM(010) using a tangential flow torch and the SCP consists of a 27.12 MHz discharge sustained in a liquid-cooled, fused silica tube surrounded by two annular electrodes. Both discharges are operated in helium at atmospheric pressure and detection was carried out by Atomic Emission Spectrometry (AES). The halides (I(-), Br(-), Cl(-)) are converted to volatile halogens by continuous flow generation based on chemical oxidation and on-line separation from the aqueous phase, via a gas-liquid separator, to be finally introduced into the plasma. The different factors affecting the emission intensity of the volatile halogens generated are compared for both discharges and the analytical performance characteristics are also evaluated. Detection limits of 17 ng ml(-1), 24 ng ml(-1) and 55 ng ml(-1) are obtained for the determination of Cl(-), Br(-), and I(-), respectively, in the ultraviolet-visible (UV-VIS) region using the MIP-AES and 45 ng ml(-1), 135 ng ml(-1) and 400 ng ml(-1) for Cl(-), Br(-), and I(-) with the SCP-AES. Lines in the near infrared (NIR) region were also evaluated for the SCP-AES detection; improvements in detection limits higher than 30 times were observed in the NIR region as compared with the UV-VIS with detection limits in the NIR of 1.4 ng ml(-1) for Cl(-), 3 ng ml(-1) for Br(-) and 13 ng ml(-1) for I(-).     

Characterization of a microwave microstrip helium plasma with gas-phase sample introduction for the optical emission spectrometric determination of bromine,chlorine, sulfur and carbon using a miniaturized optical fiber spectrometer

Continuous flow generation of Br₂, Cl₂ and H₂S coupled to a low-power 2.45 GHz microwave microstrip He plasma exiting from a capillary gas channel in a micro-fabricated sapphire wafer with microstrip lines has been used for the optical emission spectrometric determination of Br, Cl and S using a miniaturized optical fiber CCD spectrometer. Under optimized conditions, detection limits (3σ) of 330, 190 and 220 μg l^− 1 for Br, Cl and S, respectively, under the use of the Br II 478.5 nm, Cl I 439.0 nm and S I 469.0 nm lines were obtained and the calibration curves were found to be linear over 2 orders of magnitude. In addition, when introducing CO₂ and using the rotational line of the CN molecular band at 385.7 nm the detection limit for C was 4.6 μg l^− 1. The procedure developed was found to be free from interferences from a number of metal cations and non-metal anions. Only the presence of CO₃²⁻ and CN⁻ was found to cause severe spectral interferences as strong CN and C₂ molecular bands occurred as a result of an introduction of co-generated CO₂ and HCN into the plasma. With the procedure described Br, Cl and S could be determined at a concentration level of 10–30 mg l^− 1 with accuracy and precision better than 2%.     

Analytical characteristics of near-infrared nonmetal atomic emission from a helium microwave-induced plasma

Relative emission intensities for several atomic lines of C, N, O, F, S, Cl and Br between 700 and 1200 nm in an atmospheric-pressure helium microwave-induced plasma are reported. For each element the most intense near-infrared lines are compared to the most intense u.v.-visible lines in terms of signal-to-background ratios and spectral interferences. The relative-intensity data are used to calculate excitation temperatures for each element.     

A wavelength table for emission lines of non-metallic elements with transition assignments and relative intensities observed in an atmospheric pressure helium microwave-induced plasma

The emission lines of 10 non-metallic elements (H, C, N, O, F, Cl, P, S, Br and I) excited by an atmospheric pressure helium microwave-induced plasma have been tabulated with their relative intensities and transitions. These non-metallic elements were introduced into the plasma mostly as the vapor of organic compounds, although the emissions of H, N and O were observed due to the impurities in the helium gas. The spectral lines observed in the wavelength region from 190 to 850 nm were assigned with reference to established wavelength tables and tables of atomic energy levels. All emission line intensities of an element were normalized with respect to the most intense emission line of the element taken as 100.     

Br2+Cl2=2BrCl反应机理的理论和实验研究

用(U)MP2方法, 取6-311G*基组, 研究了反应Br2+Cl2=2BrCl的机理, 求得四中心和三中心的过渡态, 通过比较反应通道的活化能的大小, 得到如下结论: 双分子基元反应的最小活化能小于Cl2和Br2的离解能, 在没有光引发的条件下, 标题反应将以分子与分子作用形式完成; 若有光引发, Br2或Cl2先解离成原子, 再经过Br原子与Cl2反应或Cl原子与Br2反应, 能较快完成标题反应. 分别测定了光照和避光两种条件下的反应体系在412 nm处吸光度的变化, 证实了理论研究的结果.     

Luminescence of ruthenium halide complexes containing a hemilabile phosphine pyrenyl ether ligand

A series of Ru(II) complexes, tcc-RuX2(POC4Pyr-P,O)2 (X = Cl (3), Br (4), I (5)), containing the hemilabile phosphine pyrenyl ether ligand 4-{2-(diphenylphosphino)phenoxy}butylpyrene (POC4Pyr (1)) are reported. The synthesis and spectroscopic properties of both the ligand, POC4pyr (1), and ligand oxide, P(=O)OC4pyr 2, and the solid-state structure of 1 are reported. Complexes 3-5 react rapidly with CO to give complexes ttt-RuX2(CO)2(POC4pyr-P)2 (X = Cl (6), Br (7), I (8)). No pyrene excimer emission is detected from 3-5; however, different intensities of excimer emission are observed for 6-8. The intensity of excimer emission decreases through the series, with 6 showing the most intense response. The emission is solely due to intramolecular pyrene excimers at low concentrations (< or =10(-4) M). Comparison of the UV-vis and steady-state fluorescence spectra shows overlap between the low energy d-d absorption of 7 and 8 with excimer emission (480 nm), suggesting nonradiative energy transfer may be occurring. Once excess CO is removed, complexes 6-8 isomerize to cis-dicarbonyl complexes cct-RuX2(CO)2(POC4Pyr-P)2 (X = Cl (9), Br (10), I (11)). The intensity of excimer emission from 9-11 increases with respect to the excimer emission observed for 6-8, with 9 showing a significant increase in excimer intensity.     

Simultaneous determination of bromine and chlorine in coal using electrothermal vaporization inductively coupled plasma mass spectrometry and direct solid sample analysis

A new method for the direct analysis of coal using electrothermal vaporization inductively coupled plasma mass spectrometry and direct solid sample analysis was developed, aiming at the determination of Br and Cl. The procedure does not require any significant sample pretreatment and allows simultaneous determination of both elements to be carried out, requiring small mass aliquots of sample (about 0.5 mg). All operating parameters, including carrier gas flow-rate and RF power, were optimized for maximum sensitivity. The use of modifiers/aerosol carriers (Pd, Pd + Al and Pd + Ca) was evaluated, and the mixture of Pd and Ca was chosen, allowing pyrolysis and vaporization temperatures of 700 °C and 1900 °C, respectively. Chlorine was accurately determined using calibration against solid standards, whereas Br could also be determined using calibration against aqueous standard solutions. The limits of quantification were 0.03 μg g⁻¹ for Br and 7 μg g⁻¹ for Cl, and no spectral interferences were observed.     

Plastic identification based on molecular and elemental information from laser induced breakdown spectra: a comparison of plasma conditions in view of efficient sorting

This work is dedicated to a comparison of plasma conditions for the accurate determination of some elements: Br, Cl, Ca, P and Sb, in polymers. The comparison of the plasma conditions to sort plastics according to CN, C2 and element signals was also investigated. The comparison of a helium atmosphere and an air atmosphere led to improved results using helium as a buffer gas. The improvement is obtained in two areas, it increased the detection of halogens (Br, Cl) usually employed as flame retardants. It was also found to significantly improve the discrimination based on simple calculations of C2/He and CN/He ratios. Best conditions were based on a laser emitting at 266 nm, with a low 6 mJ energy focalized on a 50 μm spot and the helium buffer gas. A plot of C2/He against CN/He was efficient to identify the four groups of plastics employed in this study: polystyrene, polypropylene, acrylonitryle–butadiene–styrene and acrylonitryle–butadiene–styrene/polycarbonate.     

Simultaneous determination of bisphenol A and its halogenated derivatives in river water by combination of isotope imprinting and liquid chromatography-mass spectrometry

A restricted access media-molecularly imprinted polymer (RAM-MIP) for [2H16]bisphenol A (BPA-d16) was prepared by a multi-step swelling and polymerization method using 4-vinylpyridine as a functional monomer and ethylene glycol dimethacrylate as a cross-linker, followed by hydrophilic surface modification using glycerol dimethacrylate and glycerol monomethacrylate as hydrophilic monomers. The obtained RAM-MIP showed excellent molecular recognition abilities for BPA and BPA-d6 as well as BPA-d16 used as the template molecule, and good ones for tetrachlorobisphenol A (Cl4-BPA) and tetrabromobisphenol A (Br4-BPA). Next, the RAM-MIP was utilized for selective on-line pretreatment and enrichment of BPA, Cl4-BPA and Br4-BPA in a river water sample, followed by their separation and determination by LC-MS. The calibration graphs of BPA, Cl4-BPA and Br4-BPA, constructed using BPA-d6 as an internal standard, showed good linearity in the range of 12.5-200 pg/mL (r > 0.999) with a 2-mL injection of a river water sample. The inter-day precision data for the assay of BPA, Cl4-BPA and Br4-BPA at 25 pg/mL were 1.08, 3.67 and 1.58%, respectively. Furthermore, this method was successfully applied for the simultaneous determination of BPA and its halogenated derivatives in river water.     

A simple atmospheric microwave-excited emissive detector for gas chromatography

An atmospheric pressure microwave-excited emissive argon plasma is evaluated for use as a detector in conventional gas-chromatographic analysis. A range of carbon-, oxygen-, nitrogen- and halogen-containing compounds was investigated in order to optimize the sensitivity, linear working range and plasma operating conditions. For the non-selective determination of carbon-containing compounds, the atomic carbon emission at 247.9 nm was found to be most useful. At this wavelength the sensitivities for all the compounds investigated were directly proportional to the amount of carbon in the compounds. The limit of detection for these compounds at 247.9 nm was 1.94·10^-l0 g of carbon per sec. The atomic lines at 206.2 nm (I) and 470.5 nm (Br) were the best for the selective determination of iodine- and bromine-containing compounds respectively, and a new band emission at 256 nm, characteristic of chlorinecontaining compounds, gave good sensitivity.     

离子色谱法测定纯净水中F~-,BrO_3~-等6种阴离子

建立阴离子分离柱离子色谱法测定纯净水中F~-,BrO_3~-,Cl~-,NO_2~-,Br~-,NO_3~- 6种微量阴离子的方法。以SH-AC-1型阴离子柱为分离柱,柱箱温度为35℃,以1.0 mmol/L Na_2CO_3为淋洗液,流量为1.5 mL/min。F~-,BrO_3~-,Cl~-,NO_2~-,Br~-,NO_3~-的线性范围分别为20~320,40~800,40~640,10~200,50~1 000,50~1 000μg/L,线性相关系数均大于0.999,检出限为0.7~7.5μg/L,加标回收率在95.0%~106.3%之间,测定结果的相对标准偏差为1.41%~4.27%(n=5)。该方法测定结果准确、可靠,操作简便、快速,适用于纯净水中BrO_3~-,F~-,Cl~-,NO_2~-,Br~-,NO_3~- 6种阴离子的测定。     

Determination of B,Si, P,S, Cl,and Br in uranium materials by inductively coupled plasma mass spectrometry

Efficient highly sensitive methods are proposed for the direct determination of nonmetallic impurities in uranium materials by inductively coupled plasma mass spectrometry (ICP-MS). The possibility for the elimination of polyatomic overlap interferences on the signals of ³²S and ³⁵Cl using high-resolution measurements (m/Δm = 4000) was demonstrated. The influence of the operation conditions of the mass spectrometer, such as plasma power and nebulizer gas flow rate, was investigated, and the effect of the uranium matrix on the analytical signal of the isotopes to be determined was studied. The detection limit and lower limit of the analytical range for B, Si, P, S, Cl, and Br in uranium materials were estimated. The developed procedures were certified as standard trade procedures and used at the Urals Electrochemical Integrated Plant for the quality control of uranium materials.     

Formation and internal energy distribution of the CH(A2Δ) radical by electron-impact dissociation of methyl halides

The dissociative excitation of CH₃X (X = Cl, Br, I) producing CH(A²Δ) is investigated by low-energy electron impact. The onsets of the CH(AX) emission from CH₃Cl, CH₃Br and CH₃I are 11.8 ± 0.3, 11.4 ± 0.3 and 11.2 ± 0.3 eV, respectively. It can be concluded that CH₃X → CH(A) + H₂(X) + X (X = Cl, Br, I) is the predominant process for formation of CH(A) near its onset. The internal energy distributions of CH(A) evaluated by means of a simulation analysis of the CH(AX) band are nearly independent of the impact energy for impinging electrons above 19 eV.     

PIXE analysis of human stones: Comparison with data from ICP-AES

25 human stone samples previously analyzed by inductively coupled plasma atomic emission spectroscopy /ICP-AES/ and the IAEA Animal Bone Standard Reference Material were used to evaluate trace element analysis by PIXE. Bombardment with 4 MeV protons was used for the determination of Mn, Fe, Cu, Pb, Br, Rb, Sr as well as Ca. PIXE and ICP-AES data gave correlation factors better than 0.97 for the elements Ca, Fe, Zn, Sr and Pb.