Direct determination of bismuth(III) in sea water by square-wave anodic stripping voltammetry at a glassy-carbon rotating-disk electrode

A method for the determination of bismuth(III) in untreated sea water at its natural pH of 8.1 is described. A bare glassy-carbon rotating-disk electrode is preconditioned by placing in the sample at an applied potential of ?0.8 V vs. Ag/AgCl for 20 min; after stripping to ?0.4 V, bismuth is accumulated for 5 min at ?0.8 V and finally stripped in the square-wave mode. The bismuth peak appears at ca. + 0.10 V vs. Ag/AgCl; peak height is linearly related to concentration up to 2×10^?10 mol dm^?3. The method is highly selective for bismuth. The concentration of Bi(III) in the investigated sample was (6±1)×10^?11 mol dm^?3, or 12±2 ng dm^?3. The different types of response obtained are discussed.     

Flow-injection extraction spectrophotometric determination of bismuth as tetraiodobismuthate(III) with the tetramethylenebis(triphenylphosphonium) cation

Bismuth can be determined spectrophotometrically at 495 nm after its extraction as tetramethylenebis(triphenylphosphonium) tetraiodobismuthate(III) into dichloromethane. The carrier stream is 2 M sulphuric acid and the reagent stream contains 2% (w/v) potassium iodine and 0.4% (w/v) tetramethylenebis(triphenylphosphonium) bromide. The injection rate is 20 h^-1. The calibration graph is linear up to 20 μ ml^-1 bismuth and the detection limit is 0.24 μ ml^-1 bismuth, based on injection volumes of 250μl. The system has been applied to determination of bismuth in pharmaceutical samples.     

Spectrophotometric study of bismuth with N-(2-acetamido)iminodiacetic acid (ADA): Determination of bismuth in pharmaceutical formulations

A new method for the Spectrophotometric determination of bismuth using N-(2-acetamido)iminodiacetic acid as complexometric agent is proposed. The complex is formed in a wide pH range, 5.5–7.5, and has a maximum absorption at 265 nm. Beer's law is obeyed in the interval 3.8–17.9 μg of bismuth(III)/ml, with a minimum photometric error of 2.3. The molar absorptivity is 9.1 × 10³ liters/cm mol. The stoichiometry of the reaction takes place in the metal-to-ligand ratio 1:2. The interferences produced by the more common ions are studied. The method has been successfully applied to the determination of bismuth in pharmaceutical formulations.     

An analytically useful coulometric generation of micro amounts of metal ions : Part I. Electrogeneration of bismuth(III)

Bismuth(III) can be generated in a solution by electrolytically oxidizing dilute bismuth amalgam. Oxygen present in the solution contacting the amalgam also oxidizes the amalgam. Therefore normal coulometric circuits are not suitable for the generation of trace quantities of bismuth(III), even after prolonged passage of nitrogen. A procedure is described by which the interference of oxygen is eliminated so that amounts of bismuth(III) down to 5·10^-8 moles (in 30 ml) can be generated with 100% current efficiency.     

Extraction,Separation and Spectrophotometric Determination of Bismuth(III) Using 1(4′-Bromophenyl) 4,4,6-Trimethyl (1H,4H)-Pyrimidine-2-Thiol

Abstract

The operating conditions for the spectrophotometric determination of bismuth(III) with 1-(4′-bromophenyl)-4,4,6-trimethyl-(1H,4H)-pyrimidine-2-thiol (4′bromo PTPT) as a ligand by a liquid-liquid extraction technique are presented. In acidic conditions bismuth(III) forms a yellow complex with the ligand which can be extracted in chloroform with an absorption maxima at 410 nm. The molar absorptivity is 1.5×10⁴ l mole^?1 cm^?1 and Sandell's sensitivity is 14.3 ng cm^?2. The difference in the absorbance between the chloroform blank and bismuth(III) sample increases linearly in the concentration range 2-14 ppm at 0.3 M hydrochloric acid. The proposed method is extremely sensitive, rapid, reproducible and has been satisfactorily applied to the determination of trace amounts of bismuth(III) in synthetic mixtures, alloys and pharmaceutical formulations and also provides binary separation of bismuth(III) from selenium, tellurium, lead, antimony, copper and gold. The overall process of extraction and determination takes about 15 to 20 min.     

Underpotential Deposition Study and Determination of Bismuth on Gold Electrode by Using Voltammetry

ＴｈｅｃｏｍｂｉｎａｔｉｏｎｏｆｓｔｒｉｐｐｉｎｇｖｏｌｔａｍｍｅｔｒｙｗｉｔｈＵＰＤｃａｎｌｅａｄｔｏｔｈｅｉｍｐｒｏｖｅｍｅｎｔｏｆｓｅｎｓｉｔｉｖｉｔｙ ,ｓｅｌｅｃｔｉｖｉ ｔｙａｎｄｒｅｖｅｒｓｉｂｉｌｉｔｙｆｏｒｅｌｅｃｔｒｏａｎａｌｙｔｉｃａｌｐｕｒｐｏｓｅａｎｄａｖｏｉｄｔｈｅｕｓｅｏｆｔｏｘｉｃｍｅｒｃｕｒｙａｓｔｈｅｗｏｒｋｅｌｅｃｔｒｏｄｅ1ａｎｄｔｈｅｎａｎａｌｙｔｉｃａｌａｐｐｌｉｃａｔｉｏｎｓｈａｖｅｂｅｅｎｄｅｓｃｒｉｂｅｄ .2 4 Ｉｎｔｈｉｓｗｏｒｋ ,ｗｅｄｅｖｅｌｏ…     

Study of electrooxidation of binary electrolytic deposit palladium–bismuth deposited on graphite electrode surface

The phase structure of palladium–bismuth binary electrolytic deposit was studied. The electrodeposition of deposit components on the surface of a graphite electrode (GE) was carried out in situ. On current–voltage curves, the peak of bismuth electrooxidation, the peak of palladium electrooxidation and an additional peak at 0.15 V vs. Ag/AgCl are observed. The peak current at 0.15 V depends both on the concentration of palladium(II) ions and on that of bismuth(III) ions. The thermodynamic theory of alloys in the approximation of the theory of regular solutions was used for calculations. The mixing heat of the binary alloy components and the equilibrium potential of bismuth in the bismuth–palladium alloy are calculated. The calculated equilibrium potential of bismuth in an alloy with palladium is 0.12 V vs. Ag/AgCl which corresponds to the Bi₂Pd intermetallic compound (IMC). Investigation of the surface of a GE with a palladium–bismuth deposit with use of scanning electron microscope showed that the electrolytic deposit contains bismuth, palladium and the Bi₂Pd IMC. Peak at the potential of plus 0.15 V vs. Ag/AgCl is due to selective bismuth electrooxidation from the Bi₂Pd IMC.     

Fabrication of Bismuth/Multi-walled Carbon Nanotube Composite Modified Glassy Carbon Electrode for Determination of Cobalt

A bismuth/multi‐walled carbon nanotube (Bi/MWNT) composite modified electrode for determination of cobalt by differential pulse adsorptive cathodic stripping voltammetry is described. The electrode is fabricated by potentiostatic pre‐plating bismuth film on an MWNT modified glassy carbon (GC) electrode. The Bi/MWNT composite modified electrode exhibits enhanced sensitivity for cobalt detection as compared with the bare GC, MWNT modified and bismuth film electrodes. Numerous key experimental parameters have been examined for optimum analytical performance of the proposed electrode. With an adsorptive accumulation of the Co(II)‐dimethylglyoxime complex at ?0.8 V for 200 s, the reduction peak current is proportional to the concentration of cobalt in the range of 4.0×10^?10?1.0×10^?7 mol/L with a lower detection limit of 8.1×10^?11 mol/L. The proposed method has been applied successfully to cobalt determination in seawater and lake water samples.     

Syntheses,Reactions, Characterization,and Antifungal Activities of Chloro-bis-(2,2-dithio-1,3,2-dioxaphospholane/dioxaphosphorinane)bismuth(III)

Abstract

Chloro-bis(2,2-dithio-1,3,2-dioxaphospholane/dioxaphosphorinane)bismuth(III) compounds have been synthesized by the reaction of bismuth trichloride with sodium 2,2-dithio-1,3,2-dioxaphospholane/dioxaphosphorinane in 1:2 molar ratio in benzene solution. Reactions of these chloro-bis(2,2-dithio-1,3,2-dioxaphospholane/dioxaphosphorinane)-bismuth(III) compounds with sodium tetraisopropoxyborate in equimolar ratio in benzene solution yield the corresponding heterobinuclear bismuth derivatives with boron. All compounds were characterized by elemental analyses and molecular weight measurements. Plausible structures are proposed on the basis of IR and ¹H, ¹¹B, ¹³C, and ³¹P spectroscopic studies. 2-Mercapto-2-thioxo-1,3,2-dioxaphospholanes-/dioxaphosphorinanes and the corresponding chloro-bis(2,2-dithio-1,3,2-dioxaphospholane/dioxaphosphorinane)bismuth (III) compounds show antifungal activities against Fusarium and Trichoderma.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.

GRAPHICAL ABSTRACT      

Selective extraction of thallium(III) in the presence of gallium(III), indium(III), bismuth(III) and antimony(III) by salting-out of an aqueous mixture of 2-propanol

Thallium(III), in the presence of other triply charged ions such as gallium, indium, bismuth and antimony in aqueous solution, was quantitatively and selectively extracted into 2-propanol/water phase by addition of NaCl ranging from 2.5 to 4.0 mol dm⁻³. The extraction efficiencies of gallium, indium, bismuth and antimony were much lower than that of thallium(III). Thus a maximal selective separation of thallium(III) from these elements could be attained using a 2-propanol/water mixture. Thallium(III) was extracted as TlCl₄⁻ with Na⁺. The detailed extraction mechanism in the presence of chloride, water in the organic phase and counter ions is discussed.     

Determination of bismuth and copper using adsorptive stripping voltammetry couple with continuous wavelet transform

A new method is proposed for the determination of bismuth and copper in the presence of each other based on adsorptive stripping voltammetry of complexes of Bi(III)-chromazorul-S and Cu(II)-chromazorul-S at a hanging mercury drop electrode (HMDE). Copper is an interfering element for the determination of Bi(III) because, the voltammograms of Bi(III) and Cu(II) overlapped with each other. Continuous wavelet transform (CWT) was applied to separate the voltammograms. In this regards, wavelet filter, resolution of the peaks and the fitness were optimized to obtain minimum detection limit for the elements. Through continuous wavelet transform Symlet4 (Sym4) wavelet filter at dilation 6, quantitative and qualitative analysis the mixture solutions of bismuth and copper was performed. It was also realized that copper imposes a matrix effect on the determination of Bi(III) and the standard addition method was able to cope with this effect. Bismuth does not have matrix effect on copper determination, therefore, the calibration curve using wavelet coefficients of CWT was used for determination of Cu(II) in the presence of Bi(III). The detection limits were 0.10 and 0.05 ng ml⁻¹ for bismuth and copper, respectively. The linear dynamic range of 0.1-30.0 and 0.1-32.0 ng ml⁻¹ were obtained for determination of bismuth in the presence of 24.0 ng ml⁻¹ of copper and copper in the presence of 24.0 ng ml⁻¹ of bismuth, respectively. The method was used for determination of these two cations in water and human hair samples. The results indicate the ability of method for the determination of these two elements in real samples.     

Speciation of major arsenic species in seawater by flow injection hydride generation atomic absorption spectrometry

Arsenic present at 1 μg L^–1 concentrations in seawater can exist as the following species: As(III), As(V), monomethylarsenic, dimethylarsenic and unknown organic compounds. The potential of the continuous flow injection hydride generation technique coupled to atomic absorption spectrometry (AAS) was investigated for the speciation of these major arsenic species in seawater. Two different techniques were used. After hydride generation and collection in a graphite tube coated with iridium, arsenic was determined by AAS. By selecting different experimental hydride generation conditions, it was possible to determine As(III), total arsenic, hydride reactive arsenic and by difference non-hydride reactive arsenic. On the other hand, by cryogenically trapping hydride reactive species on a chromatographic phase, followed by their sequential release and AAS in a heated quartz cell, inorganic As, MMA and DMA could be determined. By combining these two techniques, an experimental protocol for the speciation of As(III), As(V), MMA, DMA and non-hydride reactive arsenic species in seawater was proposed. The method was applied to seawater sampled at a Mediterranean site and at an Atlantic coastal site. Evidence for the biotransformation of arsenic in seawater was clearly shown.     

Application of a new ion-imprinted polymer for solid-phase extraction of bismuth from various samples and its determination by ETAAS

A batch process was developed to extract bismuth ions by a novel and selective sorbent. In this study, a new Bi(III)-ion imprinted polymer was prepared by formation of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex for selective preconcentration of ultra trace amounts of bismuth. Polymerization was performed with ethylene glycol dimethacrylate, as crosslinking monomer and methacrylic acid as functional monomer; in the presence of 2,2-azobisisobutyronitrile, as initiator, via bulk polymerization. Optimum pH for maximum sorption was 2.5–3.5. Maximum sorbent capacity and enrichment factor for bismuth were 35.9?mg?g^?1 and 300, respectively. The relative standard deviation and limit of detection the method were evaluated as ±4.1% and 8.6?ng?L^?1. This method is simple, selective and sensitive and can be applied to the determination of bismuth in water, biological and plant samples.     

Differential Pulse Anodic Stripping Voltammetric Determination of Bismuth(III) with 1‐(2‐Pyridylazo)‐2‐naphthol and Ionic Liquid Modified Carbon Paste Electrode

In this paper 1‐(2‐pyridylazo)‐2‐naphthol (PAN) and ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) were mixed with graphite powder to get a modified carbon paste electrode (PAN‐IL‐CPE), which was further used for the sensitive determination of bismuth(III). By the co‐contribution of the formation of PAN‐Bi complex and the accumulation effect of IL, more bismuth(III) was electrodeposited on the surface of the PAN‐IL‐CPE. Then the reduced Bi was oxidized and detected by differential pulse anodic stripping voltammetry (DPASV) with the oxidation peak appeared at 0.17 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the bismuth(III) concentration in the range from 0.04 to 7.5 μmol L^?1 with the detection limit as 3.9 nmol L^?1. The proposed method was successfully applied to the stomach medicine sample detection with good recovery.     

Bismuth triple-decker phthalocyanine: synthesis and structure

Triclinic crystals of bismuth(III) triple-decker phthalocyanine, Bi₂Pc₃, Pc=C₃₂H₁₆N₈²⁻, were grown directly by the reaction of Bi₂Se₃ with 1,2-dicyanobenzene at 220°C. The Bi₂Pc₃ molecule is centrosymmetric with the bismuth atoms located closer to the peripheral phthalocyaninato(2−) rings than to the central ring. Each bismuth(III) ion is connected by four N-isoindole atoms to the peripheral and by four N-isoindole to the central Pc ring with average distances of 2.333 and 2.747 Å, respectively. This indicates a stronger connection of Bi(III) to the peripheral saucer-shaped macrocyclic rings than to the central rings. The neighbouring phthalocyaninato(2−) moieties in the Bi₂Pc₃ molecule are separated by a distance of 3.101(5) Å. The central Pc ring is rotated by 36.4° with respect to the peripheral ones. Differences in Bi–N bond lengths are a result of interaction of the bismuth ion with peripheral and central rings as well as the repulsion forces between two bismuth ions in the same Bi₂Pc₃ molecule, which are separated by a distance of 3.839(2) Å. The crystal packing is characterized by a distance of 3.56 Å between Pc rings of neighbouring Bi₂Pc₃ molecules.     

Spectrophotometric determination of bismuth in water samples after preconcentration of its thiourea-bromide ternary complex on activated carbon

A simple, accurate, sensitive and reliable method for the selective extraction and spectrophotometric determination of Bi(III) was developed. Bi(III) was collected on activated carbon after complexation with thiourea and bromide ion in acidic media. The complex retained on activated carbon was then desorbed with the bromide solution in N,N-dimethylformamide (DMF) and determined spectrophotometrically at 375 nm. The linear calibration ranges and limit of detection for the proposed method was 1.00×10⁻⁹-1.50×10⁻⁷ and 8.00×10⁻¹⁰ mol l⁻¹, respectively. The influence of the interfering cations and anions on the determination of bismuth was investigated. The method was successfully applied to the extraction and determination of bismuth in natural water samples.     

Simultaneous separation of tin and bismuth from water and sea water by flotation with thionalide

Summary A method is described for the simultaneous flotation of low g l^–1 levels of tin and bismuth in water and sea water. Tin(IV) and bismuth(III) in a 1000 ml sample is coprecipitated with thionalide at pH 2–3. The precipitate is floated with the aid of a surfactant and small nitrogen bubbles, then dissolved in acetone and digested with nitric and perchloric acids for hydride generation-atomic absorption spectrophotometry. Recoveries of tin and bismuth at the levels of 20 g added to water and sea water were more than 88%.     

Application of the Bismuth Film Electrode for Voltammetric Determination of Titanium Using Ti(IV)‐Oxalate‐Chlorate Catalytic System

The catalytic voltammetric protocol for the determination of titanium at a bismuth film electrode is presented. The method is based on the reduction of the Ti(IV)‐oxalate complex to Ti(III)‐oxalate in an acidic solution. It was proven that the addition of KClO₃ causes rapid oxidation of Ti(III)‐oxalate and, subsequently, an increase of the reduction peak current of Ti(IV) at the bismuth film electrode. Parameters that influence the Ti response, including the film preparation, solution pH, oxalate acid and chlorate concentrations, were optimized. The exploitation of the bismuth film electrode under the optimized conditions yielded a stable response for titanium, with high sensitivity (12.5 μA μM^?1), good precision (RSD=5.0%) and a low detection limit (1×10^?8 M).     

Flow potentiometric and constant-current stripping analysis for arsenic(V) without prior chemical reduction to arsenic(III): Application to the Determination of Total Arsenic in Seawater and Urine

Arsenic(V) is reduced to elemental arsenic on a gold-coated platinum-fibre electrode at electrolysis potentials below ?1.60 V vs. Ag/AgCl and subsequently re-oxidized, either by means of a constant current, or chemically, with gold(III) as oxidant. Total arsenic in acidified seawater can be determined by means of electrolysis for 60 s at ?1.80 V vs. Ag/AgCl and subsequent stripping in 4 M hydrochloric acid containing 2.5 M calcium chloride. The detection limit obtained after 60 s of electrolysis (ca. 0.1 μg1^?1) is about ten times lower than that obtained by the electrochemical stripping methods for arsenic(III) reported hitherto. Total arsenic in urine is determined after digestion with nitric acid and hydrogen peroxide.     

Determination of mercury in bismuth by neutron activation analysis

A method has been developed for the determination of traces of mercury in bismuth by neutron activation analysis. After sample irradiation at a flux of 7 · 10¹³ n cm^-2 s^-1 for 20 min, mercury was separated from bismuth by addition of ammonium sulfide and re-dissolution of bismuth (matrix) sulfide with nitric acid, and filtration of sulfur containing mercury on a membrane filter. The activity of the 68- or 68–77-keV region, counted with a Ge(Li) or NaI(Tl) detector, was used for quantitative measurements. The method was applied to bismuth samples containing 0.1–100 p.p.m. of mercury.