Exploiting sequential injection analysis with lab-on-valve and miniaturized potentiometric detection: Epinephrine determination in pharmaceutical products

Miniaturized potentiometric units were constructed, evaluated and incorporated in a SIA-LOV manifold in order to the control of pharmaceutical analysis. The method validation was done with ephinefrine determinations in commercial pharmaceutical products. The optimization procedures were directed at potential versus epinephrine concentration. This approach was achieved by selecting 60 cm of reactor and a flow rate of 11 μL s⁻¹ and injecting 78 μL of epinephrine standard solutions in a 1.0 × 10⁻³ mol L⁻¹ IO₄⁻ solution. A linear range was found for epinephrine concentrations between 2.0 × 10⁻⁴ and 2.5 × 10⁻³ mol L^−l with a slope of 35528 mV L mol^−l and r² = 0.997. Under these conditions the analytical results for the commercial pharmaceutical formulations of 0.908 and 0.454 mg mL⁻¹, respectively, with a R.S.D. of 0.34 for both, was obtained. Through down scaling periodate-selective electrode it was possible to benefit from the recognized advantages of the lab-on-valve sequential-injection based systems, namely regarding equipment portability, reduced consumption of the sample and the reagents and the reduction of effluent waste. Furthermore, the new periodate electrode configuration is easy to achieve in common laboratories and enables the implementation of low volume detection cell where the electrical noise, that is frequently presented in potentiometric based procedures, is significantly reduced.     

Two rapid and sensitive automated methods for the determination of nitrite and nitrate in soil samples

Spectrophotometric flow injection methods were developed for the individual determination of nitrite or nitrate, and for the simultaneous determination of nitrite and nitrate, in soil samples. Nitrite was determined directly using a modified version of the Griess-Ilosvay diazo-coupling reaction, measuring at 543 nm the absorbance of the azo-dye complex formed. Simultaneous nitrite and nitrate determinations were based on on-line nitrate reduction in a micro column containing copperised cadmium. A single chromogenic reagent containing all the necessary reactants was used in both methods. For determinations, the chemical and instrumental variables were optimised by univariate analysis and simplex chemometric method. The optimised conditions gave a linear calibration range between 0.05 and 1.6 µg m L^− 1 for N-NO₂⁻ and between 0.05 and 7.0 µg m L^− 1 for N-NO₃⁻. The detection limits for nitrite and nitrate were 22 µg L^− 1 and 44 µg L^− 1 respectively. The proposed methods allowed up to 35-40 samples per hour to be analysed with good precision. The simultaneous method was successfully used for the determination of nitrite and nitrate in soil samples (the results obtained were validated against those obtained by reference methods). The proposed methods are simpler and faster than conventional methods and could be routinely used in environmental monitoring laboratories.     

Selective determination of penicillamine by on-line vapor-phase generation combined with Fourier transform infrared spectrometry

In this work, an on-line system with vapor-phase generation (VPG) and Fourier transform infrared (FTIR) spectrometric detection has been developed as a direct and highly selective analytical technique for the assay of penicillamine (PA). Potassium iodate solution was injected into a reactor, heated at 75 °C, containing PA. The CO generated under these conditions was transported by means of N₂ gas carrier stream to an infrared gas cell and corresponding FTIR spectra were acquired in a continuous mode. The maximum absorbance of CO band at 2170 cm⁻¹, corrected by a baseline established between 2240 and 2000 cm⁻¹ at a nominal resolution of 2 cm⁻¹, was selected as a measurement criterion. Initially, the effect of different chemical, physical and spectroscopic parameters, such as concentration and volume of oxidant, pH, equilibrium time, reactor temperature, reactor volume, N₂ carrier flow rate and number of scans on the analytical signals were evaluated by using a short path length (10 cm) IR gas cell. At optimum experimental conditions, the method provided a relatively broad linear dynamic range of 4-380 mg L⁻¹, a limit of detection of 0.5 mg L⁻¹, a sampling frequency of 15 h⁻¹ and a relative standard deviation (R.S.D.) of 1.6%. Further, the method was successfully applied to the determination of PA in pharmaceutical formulations and results compared well with those obtained by a reference colorimetric method.     

Flow-injection fluorometric quantification of pyruvate using co-immobilized pyruvate decarboxylase and aldehyde dehydrogenase reactor: Application to measurement of acetate, citrate and l-lactate

A flow-injection system for the quantification of pyruvate based on the coupled reactions of pyruvate decarboxylase (PDC) and aldehyde dehydrogenase (AlDH) was conceived and optimized. A co-immobilized PDC and AlDH reactor was introduced into the flow line. Sample and reagent (NAD⁺) were injected into the flow line by an open sandwich method and the increase of NADH produced by the immobilized-enzyme reactor was monitored fluorometrically at 455 nm (excitation at 340 nm). Linear relationships between the responses and concentrations of pyruvate were observed in the ranges of 2.0 × 10⁻⁵ to 1.5 × 10⁻³ M at the flow rate of 1.0 ml min⁻¹ and 5.0 × 10⁻⁶ to 1.0 × 10⁻³ M at the flow rate of 0.5 ml min⁻¹. The relative standard deviation for 10 successive injections was 0.95% at the 1.0 mM level. This FIA system for pyruvate was applied to the measurement of acetate, citrate and l-lactate.     

Batch and hydrodynamic monitoring of vitamin C using novel periodate selective sensors based on a newly synthesized Ni(II)-Schiff bases complexes as a neutral receptors

A highly selective membrane electrodes based on a two newly synthesized nickel (II) Schiff bases, [NiL¹] and [NiL²] where L¹ and L² are N,N/bis(salicylaldehyde)4,5-dimethyl-1,2-phenylenediamine (H₂L¹) and N,N/bis(salicylaldehyde)4,5-dichloro-1,2-phenylenediamine (H₂L²) were used as a neutral carrier ionophores for static and hydrodynamic potentiometric mode of operations for the determination of periodate. Under static mode of operation, the sensors displayed a near-Nernstian slope of −66.1 ± 0.8 and −59.9 ± 1.1 mV decade⁻¹ of activity and detection limits to 5.2 × 10⁻⁶ and 7.3 × 10⁻⁶ mol L⁻¹ for the sensors based on [NiL¹] and [NiL²], respectively. Under hydrodynamic mode of operation (FIA), the slope of the calibration plot, limit of detection, and working linear range were −71.1 mVdecade⁻¹ of activity, 7.3 × 10⁻⁶ and 1.0 × 10⁻⁵ to 1.0 × 10⁻³ mol L⁻¹, respectively. The response time of the sensors in whole concentration ranges was very short (<10 s). The response of the sensors was independent on the pH range of 3-8. A tubular version was further developed and coupled to a flow injection system for ascorbic acid (AA) determination in beverages and pharmaceutical preparations. This approach was achieved by selecting a 50-cm reactor and an overall flow of 3 mL min⁻¹, and injecting volume 100 μL of AA standards in a 1.0 × 10⁻⁴ mol L⁻¹ IO₄⁻ solution. Under these conditions, a linearity range of 2-13 μg mL⁻¹, with a slope of 4.97 mV (mg/L)⁻¹ (r² = 0.9995), detection limit 0.9 mg L⁻¹ and a reproducibility of ±1.1 mV (n = 5) was recorded. This simple and inexpensive flow injection analysis manifold, with a good potentiometric detector, enabled the analysis of ∼50 samples h⁻¹ without requiring pretreatment procedures. An average recovery of 98.8% and a mean standard deviation of 1.3% were obtained.     

Flow injection on-line preconcentration of low levels of Cr(VI) with detection by ETAAS: Comparison of using an open tubular PTFE knotted reactor and a column reactor packed with PTFE beads

A flow injection (FI) on-line sorption preconcentration procedure utilizing a packed column reactor and combined with electrothermal atomic absorption spectrometry (ETAAS) is proposed for the determination of low levels of Cr(VI) in water samples. Polytetrafluoroethylene (PTFE) beads packed in a mini-column is used as sorbent material. The complex formed between Cr(VI) and ammonium pyrrolidine dithiocarbamate (APDC) is sorbed on the PTFE beads, and is subsequently eluted by an air-monosegmented discrete zone of absolute ethanol (35 μl), the analyte being quantified by ETAAS.The preconcentration procedure using the proposed column significantly enhances the preconcentration efficiency as compared with the preconcentration approach incorporating an open tubular PTFE knotted reactor (KR). Comparing the two procedure for equal surface sorption area, the advantages of using a packed column are observed in terms of limit of detection, enrichment factor and retention efficiency. With a preconcentration time of 60 s, and a sample flow rate of 5.0 ml l⁻¹, the enrichment factor (30.1) and the retention efficiency (24.1%) were doubled, yielding a detection limit (3σ) as low as 8.8 ng l⁻¹. The sample frequency was 16.7 h⁻¹. The concentration efficiency was 8.38 and the precision was 1.05% at 0.5 μg l⁻¹ of Cr(VI). The proposed column has been applied successfully to the analysis of natural water and synthetic seawater. Its performance was verified by the analysis of two certified Cr(VI)-reference materials and by recovery measurements on spiked samples.     

A multicommuted flow system for sequential spectrophotometric determination of hydrosoluble vitamins in pharmaceutical preparations

A multicommuted flow system is proposed for spectrophotometric determination of hydrosoluble vitamins (ascorbic acid, thiamine, riboflavine and pyridoxine) in pharmaceutical preparations. The flow manifold was designed with computer-controlled three-way solenoid valves for independent handling of sample and reagent solutions and a multi-channel spectrophotometer was employed for signal measurements. Periodic re-calibration as well as the standard addition method was implemented by using a single reference solution. Linear responses (r=0.999) were obtained for 0.500-10.0 mg l⁻¹ ascorbic acid, 2.00-50.0 mg l⁻¹ thiamine, 5.00-50.0 mg l⁻¹ riboflavine and 0.500-8.00 mg l⁻¹ pyridoxine. Detection limits were estimated as 0.08 mg l⁻¹ (0.5 μmol l⁻¹) ascorbic acid, 0.8 mg l⁻¹ (2 μmol l⁻¹) thiamine, 0.2 mg l⁻¹ (0.5 μmol l⁻¹) riboflavine and 0.1 mg l⁻¹ (0.9 μmol l⁻¹) pyridoxine at 99.7% confidence level. A mean sampling rate of 60 determinations per hour was achieved and coefficients of variation of 1% (n=20) were estimated for all species. The mean reagent consumption was 25-fold lower in relation to flow-based procedures with continuous reagent addition. Average recoveries between 95.6 and 100% were obtained for commercial pharmaceutical preparations. Results agreed with those obtained by reference methods at 95% confidence level. The flow system is suitable for application in quality control processes and in dissolution studies of vitamin tablets.     

Spectrophotometric flow-injection analysis of mercury(II) in pharmaceuticals with p-nitrobenzoxosulfamate

A new, simple and rapid spectrophotometric FI method for the accurate and precise determination of Hg(II) in pharmaceutical preparations has been developed. The method is based on the measuring the decrease of absorbance intensity of p-nitrobenzoxosulfamate (NBS) due to the complexation with Hg(II). The absorption peak of the NBS, which is decreased linearly by addition of Hg(II), occurs at 430 nm in 2×10⁻⁴ mol l⁻¹ HNO₃ as a carrier solution. Optimization of chemical and FI variables has been made. A micro column consisting of several packing materials applied instead of reaction coil was also investigated. A background level of Fe(III) maintained in reagent carrier solution with NBS was found useful for sensitivity and selectivity. Under the optimized conditions, the sampling rate was over 100 h⁻¹, the calibration curve obtained were linear over the range 1-10 μg ml⁻¹, the detection limit was lower than 0.2 μg ml⁻¹ for a 20 μl injection volume, and the precision [S_r=1% at 2 μg ml⁻¹ Hg(II) (n=10)] was found quite satisfactory. Application of the method to the analysis of Hg(II) in pharmaceutical preparations resulted a good agreement between the expected and found values.     

Flow injection-chemiluminescence determination of propranolol in pharmaceutical preparations

A rapid and precise continuous-flow method is described for the determination of propranolol based on the chemiluminescence (CL) produced by its reaction with potassium permanganate in a sulphuric acid medium. The optimum chemical conditions for the chemiluminescence emission were investigated. Two manifolds were tested and their characteristics such as the length of the reactor, injection volume and flow rate were compared. When using the selected manifold, propranolol gives a linear calibration graph over the concentration range 1.0-17.5 mg l⁻¹. The detection limit calculated as proposed by IUPAC was 70 ng ml⁻¹ and the detection limit calculated as proposed by Clayton was 0.87 mg l⁻¹. For analysis of 10 solutions of 10.0 mg l⁻¹ propranolol, if error propagation theory is assumed, the relative error was 0.1%. The standard deviation (S.D.) for 10 replicate samples was 0.07 mg l⁻¹. The method has been validated versus a published fluorimetric method.The present chemiluminescence procedure was applied to the determination of propranolol in simple British and Spanish pharmaceutical formulations, with excellent recoveries, as the determination is free from interference from common excipients. However, some drugs, such as hydralazine and bendroflumethizide which may also be present in the formulation, increase the emission intensity.     

Greener analytical method for the determination of copper(II) in wastewater by micro flow system with optical sensor

Greener analytical method using micro flow system for the determination of Cu(II) in wastewater samples was designed and investigated. The micro flow system consisted of a planar glass chip with poly(dimethylsiloxane) (PDMS) top plate and fixed with fiber optic probe as optical sensor for monitoring of Cu(II) that reacted with 2-carboxy-2′-hydroxy-5′-sulfoformazyl benzene (zincon) on the chip at 605 nm. This design gave a satisfied sensitivity with a linear calibration graph over the range of 0.1-3.0 μg mL⁻¹ of Cu(II) and correlation coefficient 0.9991. The percentage relative standard deviation was 2.5 for 10-replicate measurements and the limit of detection (LOD) was 0.1 μg mL⁻¹. This system has been successfully applied to the determination of Cu(II) in wastewaters from electroplating industry with less reagents and samples consumption and diminutive waste generation.     

Determination of trace elements in natural waters by inductively coupled plasma time of flight mass spectrometry after flow injection preconcentration in a knotted reactor

A flow injection on-line sorption system was developed for the separation and preconcentration of traces of Ag, Cd, Co, Ni, Pb, U and Y from natural water samples with subsequent detection by ICP TOF MS. Simultaneous preconcentration of the analytes was achieved by complexation with the chelating reagent 1-phenyl-3-methyl-4-benzoylpyrazol-5-one immobilized on the inner walls of a (200 cm × 0.5 mm) PTFE knotted reactor. The analytes were eluted and transported to an axial ICP TOF MS system with 1% (v/v) HNO₃ containing 0.3 μg l⁻¹ of Rh as an internal standard using ultrasonic nebulization. The detection limits (3σ) varied from 0.3 ng l⁻¹ for Y to 15.2 ng l⁻¹ for Ni and the precision (R.S.D.) was better than 4%. Using a loading time of 90 s and a sample flow rate of 4.5 ml min⁻¹, enhancement factors of 3-14 were obtained for the different analytes in comparison with their direct determination by ICP TOF MS with ultrasonic nebulization without preconcentration. The accuracy of the method was demonstrated by analysis of water based certified reference materials.     

Quantification of N-acetylcysteine in pharmaceuticals using cobalt phthalocyanine modified graphite electrodes

Flow injection analysis (FIA) with amperometric detection was employed for the quantification of N-acetylcysteine (NAC) in pharmaceutical formulations, utilizing an ordinary pyrolytic graphite (OPG) electrode modified with cobalt phthalocyanine (CoPc). Cyclic voltammetry was used in preliminary studies to establish the best conditions for NAC analysis. In FIA-amperometric experiments the OPG-CoPc electrode exhibited sharp and reproducible current peaks over a wide linear working range (5.0 × 10⁻⁵-1.0 × 10⁻³ mol L⁻¹) in 0.1 mol L⁻¹ NaOH solution. High sensitivity (130 mA mol⁻¹ cm²) and a low detection limit (9.0 × 10⁻⁷ mol L⁻¹) were achieved using the sensor. The repeatability (R.S.D.%) for 13 successive flow injections of a solution containing 5.0 × 10⁻⁴ mol L⁻¹ NAC was 1.1%. The new procedure was applied in analyses of commercial pharmaceutical products and the results were in excellent agreement with those obtained using the official titrimetric method. The proposed amperometric method is highly suitable for quality control analyses of NAC in pharmaceuticals since it is rapid, precise and requires much less work than the recommended titrimetric method.     

Ionic liquids monolithic columns for protein separation in capillary electrochromatography

A series of ionic liquids (ILs) monolithic capillary columns based on 1-vinyl-3-octylimidazolium (ViOcIm⁺) were prepared by two approaches (“one-pot” approach and “anion-exchange” approach). The effects of different anions (bromide, Br⁻; tetrafluoroborate, BF₄⁻; hexafluorophosphate, PF₆⁻; and bis-trifluoromethanesulfonylimide, NTf₂⁻) on chromatography performance of all the resulting columns were investigated systematically under capillary electrochromatography (CEC) mode. The results indicated that all these columns could generate a stable reversed electroosmotic flow (EOF) over a wide pH range from 2.0 to 12.0. For the columns prepared by “one-pot” approach, the EOF decreased in the order of ViOcIm⁺Br⁻ > ViOcIm⁺BF₄⁻ > ViOcIm⁺PF₆⁻ > ViOcIm⁺NTf₂⁻ under the same CEC conditions; the ViOcIm⁺Br⁻ based column exhibited highest column efficiencies for the test small molecules; the ViOcIm⁺NTf₂⁻ based column possessed the strongest retention for aromatic hydrocarbons; and baseline separation of four standard proteins was achieved on ViOcIm⁺NTf₂⁻ based column corresponding to the highest column efficiency of 479 000 N m⁻¹ for cytochrome c (Cyt c). These results indicated that the property of ILs based columns could be tuned successfully by changing anions, which gave these columns potential to separate both small molecules and macro biomolecules.     

Perovskite membrane reactor for continuous and isothermal redox hydrogen production from the dissociation of water

The redox water splitting is one of the most promising routes for sustainable hydrogen production. Towards this goal, serious technological obstacles are set: (i) by the non-isothermal operation of the redox process, that causes serious reactor construction problems, and (ii) by the need for efficient high temperature oxygen/hydrogen separation technology which is a very challenging development. In this paper, perovskite materials having the formula La_0.3Sr_0.7FeO₃ were synthesized and subsequently tested for their high temperature oxidation/reduction behavior. The redox activity of the materials in relation to the water splitting reaction has been also investigated. Dense, disc shaped membranes of the materials were synthesized and placed in a membrane reactor. Experiments at 1133 K revealed the possibility of performing the reduction and oxidation steps simultaneously and isothermally on each side of the membrane reactor. A steady-state situation was thereby achieved where hydrogen was continuously produced on one side while the material was simultaneously regenerated on the other side. The created oxygen vacancy gradient formed the driving force for a continuous flux of vacancies from the membrane reduction surface to the membrane oxidation surface. The hydrogen production rate under the particular experimental conditions estimated to be ∼47.5 cm³ H₂ (STP) m⁻² min⁻¹. It could be increased by a factor of approximately 3, up to ∼145 cm³ H₂ (STP) m⁻² min⁻¹, if the membrane reduction was enhanced with a reductant such as carbon monoxide. This approach resulted in an efficient execution of the water gas shift reaction towards high purity hydrogen production.     

Determination of traces of palladium in stream sediment and auto catalyst by FI-ICP-OES using on-line separation and preconcentration with QuadraSil TA

A flow injection analysis (FIA) method using on-line separation and preconcentration with a novel metal scavenger beads, QuadraSil™ TA, has been developed for the ICP-OES determination of traces of palladium. QuadraSil TA contains diethylenetriamine as a functional group on spherical silica beads and shows the highest selectivity for Pd(II) at pH 1 (0.1 mol l⁻¹ hydrochloric acid) solution. An aliquot of the sample solution prepared as 0.1 mol l⁻¹ in hydrochloric acid was passed through the QuadraSil TA column. After washing the column with the carrier solution, the Pd(II) retained on the column was eluted with 0.05 mol l⁻¹ thiourea solution and the eluate was directly introduced into an ICP-OES. The proposed method was successfully applied to the determination of traces of palladium in JSd-2 stream sediment certified reference material [0.019 ± 0.001 μg g⁻¹ (n = 3); provisional value: 0.0212 μg g⁻¹] and SRM 2556 used auto catalyst certified reference material [315 ± 4 μg g⁻¹ (n = 4); certified value: 326 μg g⁻¹]. The detection limit (3σ) of 0.28 ng ml⁻¹ was obtained for 5 ml of sample solution. The sample throughputs for 5 ml and 100 μl of the sample solutions were 10 and 15 h⁻¹, respectively.     

Rapid spectrophotometric determination of fosfestrol following on-line hydrolysis by alkaline phosphatase using flow injection and chasing zones

A new flow injection (FI) method is reported for the spectrophotometric determination of fosfestrol (diethyl-stilbestrol (DES) diphosphate) in pharmaceutical formulations. The proposed method is based on the on-line hydrolysis of the analyte by alkaline phosphatase (Al-Pase) using a “chasing zones” FI manifold. The orthophosphate ions, thus, generated are determined spectrophotometrically (λ_max=690 nm) using the molybdenum blue approach. The chemical and FI variables affecting the enzymatic reaction were investigated. The proposed method is very precise (s_r=1.1% at 1×10⁻⁴ mol l⁻¹ fosfestrol, n=12), fast (allowing up to 40 samples h⁻¹ to be analyzed) and has a determination range of 2×10⁻⁵ to 2×10⁻⁴ mol l⁻¹, with a satisfactory 3σ detection limit of 5×10⁻⁶ mol l⁻¹. The method was shown to provide accurate determinations of the fosfestrol concentration in a pharmaceutical formulation, giving relative errors, e_r, of +0.6 and −0.5% compared to the value stated by the supplier (Asta Medica Inc.) and the concentration derived using a method recommended by the United States Pharmacopoeia XXI, respectively. In addition, the average recoveries of known amounts of the analyte ranged between 99.2 and 101.2%.     

Flow injection chemiluminescence determination of paracetamol

A simple chemiluminometric method using flow injection has been developed for the determination of paracetamol (acetaminophen), based on the chemiluminescence produced by the reduction of tris(2,2′-bipyridyl)ruthenium(III). The latter is obtained by oxidation of tris(2,2′-bipyridyl)ruthenium(II) by potassium permanganate in dilute sulphuric acid in the presence of paracetamol. A standard or sample solution was injected into the ruthenium(II) stream (flow rate 1.5 ml min⁻¹) which was then merged with potassium permanganate in dilute sulphuric acid stream (flow rate 0.5 ml min⁻¹). The chemiluminescence intensity is enhanced by the presence of manganese(II) ions. Under the optimum conditions, a linear calibration graph was obtained over the range of 0.3-50.0 μg ml⁻¹ and the detection limit was 0.2 μg ml⁻¹ (s/n = 3). The relative standard deviation of the proposed method calculated from 20 replicate injections of 5.0 μg ml⁻¹ paracetamol was 1.1%. The sample throughput was 90 h⁻¹. The method was successfully applied to the determination of paracetamol in commercial pharmaceutical formulations.     

Field measurement of nitrate in marine and estuarine waters with a flow analysis system utilizing on-line zinc reduction

A sensitive reagent-injection flow analysis method for the spectrophotometric determination of nitrate in marine, estuarine and fresh water samples is described. The method is based on the reduction of nitrate in a micro column containing zinc granules at pH 6.5. The nitrite formed is reacted with sulfanilamide and N-(1-naphthyl)ethylene diamine (Griess reagent), and the resulting azo compound is quantified spectrophotometrically at 520 nm. Water samples in the range of 3-700 μg L⁻¹ NO₃⁻-N can be processed with a throughput of up to 40 samples per hour, a detection limit of 1.3 μg L⁻¹ and reproducibility of 1.2% RSD (50 μg L⁻¹ NO₃⁻-N, n = 10). The proposed method was successfully applied for the determination of nitrate in estuarine waters and the reliability was assessed by the analyses of certified reference materials and recovery experiments. The method is suitable for waters with a wide range of salinities, and was successfully used for more than 3200 underway nitrate measurements aboard SV Pelican1 in the “Two Bays” cruise in January 2010.     

Determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder by flow injection analysis with spectrophotometric detection

In this work, a flow injection system with spectrophotometric detection was developed for the determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder. Reaction between Quinizarine (1,4-dihydroxyanthraquinone) and Li(I) ion in alkaline medium containing dimethylsulfoxide (DMSO) was explored for this purpose. The flow system was optimized regarding to its chemical (DMSO, Quinizarine and NaOH concentrations and sample pH) and physical parameters (sample loop volume, carrier flow rate and reactor length) in order to establish better conditions in terms of sensitivity and sampling frequency. The results obtained showed that the concentration of DMSO in the reagent solution presents remarkable influence on the magnitude of analytical signal. Chemical species that could be found in the formulations such as Na(I), K(I), Mg(II), Ca(II), Ti(IV), Cl⁻, CO₃²⁻ e sodium dodecylsulfate were tested as possible interfering ions. Among them, only non-monovalent cations presented noticeable interference on lithium signal. However, they were not found in concentrations high enough to cause interference in the determination of lithium in the samples. Sample preparation was performed by sonicating a slurry prepared by dispersing 100 mg of powdered sample in 15 mL of 0.10 mol L⁻¹ HCl solution. Results obtained by developed methodology were not statistically different from those obtained by flame emission spectrometry. In the optimized conditions the method presented a linear range of 5-40 mg L⁻¹ and a relative standard deviation of 3.6% at 5 mg L⁻¹ Li concentration. Detection and quantification limits were 0.54 and 1.8 mg L⁻¹, respectively. Sampling frequency, calculated as the time interval passed between two consecutive injections, was 60 samples per hour. The methodology was successfully applied in the determination of lithium in three commercial samples.     

A simple and green analytical method for determination of iron based on micro flow analysis

A simple, inexpensive and reagent-less colorimetric micro flow analysis (μFA) system was implemented in a polymethyl methacrylate (PMMA) micro fluidic manifold. A T-shaped micro channel on a PMMA chip was fabricated by laser ablation and topped with molded polydimethylsiloxane (PDMS). The fabricated μFA system was integrated with the optical components as detector and applied to the determination of iron in water samples. It is based on the measurement of Fe(III)-nitroso-R salt complex at 720 nm formed by the reaction between Fe(III) and nitroso-R salt in an acetate buffer solution pH 5. The proposed μFA consumed very small amount of reagent and sample, it released waste of less than 2.0 mL h⁻¹. The relative standard deviation (R.S.D.) was less than 2% (n = 11) with the recovery of 98.7 ± 0.12 (n = 5). The linear range for the determination of iron in water samples was over the range of 0.05-4.0 μg mL⁻¹ with a correlation coefficient (r²) of 0.9994. The limit of detection (3σ) and limit of quantitation (10σ) were 0.021 μg mL⁻¹ and 0.081 μg mL⁻¹, respectively with a sample throughput of 40 h⁻¹.