Solid-phase microcolumn extraction and gas chromatography-mass spectrometry identification of volatile organic compounds emitted by paper

A rapid non-destructive sampling technique for the analysis of volatile organic compounds (VOCs) emitted by paper sheets is described. A capillary, which is connected to a microcolumn packed with Tenax TA, is inserted between two sheets at the centre of a paper stack encapsulated inside a PET/Al/PE composite foil. The other end of the microcolumn is connected to a gas-tight syringe and an appropriate volume of gaseous phase is aspirated. The microcolumn is then thermally desorbed in a modified GC inlet (modification is presented) and analysed by gas chromatography-mass spectrometry (GC-MS). In the chromatogram from the analysis of artificially aged paper sample 21 compounds were identified. Advantages of the method including the short sampling time (1 min), simplicity and economic aspect are discussed.     

Preparation of novel solid-phase microextraction fibers by sol-gel technology for headspace solid-phase microextraction-gas chromatographic analysis of aroma compounds in beer

3-(Trimethoxysilyl)propyl methacrylate (TMSPMA) was first used as precursor as well as selective stationary phase to prepare the sol-gel-derived TMSPMA-hydroxyl-terminated silicone oil (TMSPMA-OH-TSO) solid-phase mircroextraction (SPME) fibers for the analysis of aroma compounds in beer. TMSPMA-OH-TSO was a medium polarity coating, and was found to be very effective in carrying out simultaneous extraction of both polar alcohols and fatty acids and nonpolar esters in beer. The extraction temperature, extraction time, and ionic strength of the sample matrix were modified to allow for maximium sorption of the analytes onto the fiber. Desorption temperature and time were optimized to avoid the carryover effects. To check the matrix effects, several different matrices, including distilled water, 4% ethanol/water (v/v) solution, a concentrated synthetic beer, a "volatile-free" beer and a real beer were investigated. Matrix effects were compensated for by using 4-methyl-2-pentanol as internal standard and selecting the "volatile-free" beer as working standard. The method proposed in this study showed satisfactory linearity, precision and detection limits and accuracy. The established headspace SPME-gas chromatography (GC) method was then used for determination of volatile compounds in four beer varieties. The recoveries obtained ranged from 92.8 to 105.8%. The relative standard deviations (RSD, n = 5) for all analytes were below 10%. The major aroma contributing substances of each variety were identified via aroma indexes.     

Determination of carbonyl compounds in beer by derivatisation and headspace solid-phase microextraction in combination with gas chromatography and mass spectrometry

Headspace solid-phase microextraction (SPME) followed by gas chromatography and mass spectrometry was applied for quantification of 41 chemically diverse carbonyl compounds in beer. Therefore, in-solution derivatisation with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine (PFBHA) combined with SPME was optimised for fibre selection, PFBHA concentration, extraction temperature and time and ionic strength. Afterwards, the method was calibrated and validated successfully and extraction efficiency was compared to sampling with on-fibre derivatisation. In-solution derivatisation enabled the detection of several compounds that were poorly extracted with on-fibre derivatisation such as 5-hydroxymethylfurfural, acrolein, hydroxyacetone, acetoin, glyoxal and methylglyoxal. Others, especially (E)-2-nonenal, were extracted better with on-fibre derivatisation.     

气相色谱-质谱法分析啤酒中酒花香气成分

利用顶空固相微萃取-气相色谱质谱技术(HS-SPME/GC-MS)建立了定量分析啤酒中19种源自酒花的微量香气成分的方法。研究了不同萃取头、萃取时间、萃取温度对萃取效果的影响,最终确定HS-SPME最佳萃取条件为采用PDMS萃取头对啤酒样品在50℃下萃取60 min。在最佳萃取条件下,采用啤酒为基体以减少基体干扰,建立标准曲线,随后在SIM模式下以萜品烯-4-醇为内标定量测定了啤酒中酒花香气物质的含量。19种物质的回收率在81.2%～116.8%之间,相对标准偏差(RSD)低于9.8%,在5个加标浓度下,R2大于0.99。相比于传统方法,本方法所需样品量少、灵敏度高、操作过程简便,能准确的检测出啤酒中酒花香气物质的含量。     

Fast determination of VOCs in workplace air by solid-phase extraction and gas chromatography-mass spectrometry

Summary A fast, simple, and reliable method is presented for the determination of atmospheric semi-volatile organic pollutants at μg m⁻³ levels. The method has been used to monitor potentially carcinogenic toxic compounds to which workers are exposed in workplaces, and to measure the same compounds in outdoor air. Dedicated to Michele Di Pasquale (deceased).     

Determination of chloro-s-triazines including didealkylatrazine using solid-phase extraction coupled with gas chromatography-mass spectrometry

Chloro-s-triazines are a class of compounds comprising atrazine, simazine, propazine, cyanazine and their chlorinated metabolites. The US Environmental Protection Agency (EPA) has determined that selected chloro-s-triazines--atrazine, simazine, propazine, deethylatrazine, deisopropylatrazine, and didealkylatrazine--have a common mode of toxicity related to endocrine disruption. In this paper, a dual-resin solid-phase extraction (SPE) gas chromatography-mass spectrometry (GC-MS) method is reported that provides for each of these chloro-s-triazines including the polar metabolite, didealkylatrazine. The method utilizes deuterated internal standards for quantitation and terbuthylazine as a recovery standard. The limit-of-detection was 0.01 microg/L for simazine, deethylatrazine, deisopropylatrazine and didealkylatrazine, and 0.02 microg/L for atrazine and propazine in surface water. Mean recoveries for 0.5 and 3.0 microg/L spikes for atrazine, simazine, propazine, deethylatrazine, deisopropylatrazine and didealkylatrazine were 94, 104, 103, 110, 108 and 102%, respectively, in surface water. The method was also validated by matrix spikes into fourteen different raw and treated natural surface waters. This method is useful for monitoring "total chloro-s-triazines" in both raw and treated drinking waters.     

Development and validation of a solid-phase microextraction method for the analysis of volatile organic compounds in groundwater samples

Summary Solid-phase microextraction is a relatively recent extraction technique for sample preparation. It has been used successfully to analyse environmental pollutants in a variety of matrices such as soils, water and air. In this work, a simple and rapid method for the analysis of volatile organic and polar compounds from polluted groundwater samples by SPME coupled with gas chromatography (GC) is described. Different types of fibres were studied and the extraction process was optimised. The fibre that proved to be the best to analyse this kind of samples was CAR-PDMS. The method was validated by analysis of synthetic samples and comparison with headspace—GC. The optimised method was successfully applied to the analysis of ground-water samples.     

Determination of acetone in seawater using derivatization solid-phase microextraction

Acetone plays an important role in the chemistry of both the atmosphere and the ocean, due to its potential effect on the tropospheric HO_x (= HO + HO₂) budget, as well as its environmental and health effects. We discuss the development of a mobile, sensitive, selective, economical and facile method for the determination of acetone in seawater. The method consists of derivatizing acetone to its pentafluorobenzyl oxime using 1,2,3,4,5-pentafluorobenzylhydroxylamine (PFBHA), followed by solid-phase microextraction (SPME) and analysis by gas chromatography/mass spectrometry (GC/MS). A detection limit of 3.0 nM was achieved. The buffering capacity of seawater imposes challenges in using the method’s optimum pH (3.7) on seawater samples, requiring calibration standards to be made in buffered salt water and the acidification of seawater samples and standards prior to extraction. We employed the technique for analysis of selected surface seawater samples taken on the Nordic seas during the ARK-XX/1 cruise (R.V. Polarstern). An upper limit of 5.5–9.6 nM was observed for acetone in these waters, the first acetone measurements reported for far North Atlantic and Arctic waters. Simplified schematic of transformations of organic compounds at the atmosphere–ocean interface     

Role of counteranions in polymeric ionic liquid-based solid-phase microextraction coatings for the selective extraction of polar compounds

A polymeric ionic liquid (PIL) poly(1-vinyl-3-hexylimidazolium chloride) (poly(ViHIm⁺Cl⁻)) was designed as a coating material for solid phase microextraction (SPME) to extract polar compounds including volatile fatty acids (VFAs) and alcohols. The extracted analytes were analyzed by using gas chromatography (GC) coupled with flame ionization detection (FID). Extraction parameters of the HS–SPME–GC–FID method, such as ionic strength, extraction temperature, pH and extraction time were optimized. Calibration studies were carried out under the optimized conditions to further evaluate the performance of the PIL-based SPME coating. For comparison purposes, the PIL poly(1-vinyl-3-hexylimidazolium bis[(trifluoromethyl)sulfonyl]imide) (poly(ViHIm⁺NTf₂⁻)) was also used as the SPME coating to extract the same analytes. The results showed that the poly(ViHIm⁺Cl⁻) PIL coating had higher selectivity towards more polar analytes due to the presence of the Cl⁻ anion which provides higher hydrogen bond basicity than the NTf₂⁻ anion. The limits of detection (LODs) determined by the designed poly(ViHIm⁺Cl⁻) PIL coating ranged from 0.02 μg L⁻¹ for octanoic acid and decanoic acid and 7.5 μg L⁻¹ for 2-nitrophenol, with precision values (as relative standard deviation) lower than 14%. The observed performance of the poly(ViHIm⁺Cl⁻) PIL coating was comparable to previously reported work in which commercial or novel materials were used as SPME coatings. The selectivity of the developed PIL coatings was also evaluated using heptane as the matrix solvent. This work demonstrates that the selectivity of PIL-based SPME coatings can be simply tuned by incorporating different counteranions to the sorbent coating.     

顶空进样气相色谱法检测啤酒中乙醛

建立了项空自动进样气相色谱法测定啤酒发酵液中乙醛含量的方法.检测条件优化为:顶空进样器平衡温度70℃,平衡时间30 min;色谱柱初始温度40℃,经程序升温10℃/min到180℃;柱流量1.2 mL/min,加盐量1.8g.对不同浓度的乙醛标准溶液进样测定,标准曲线证明线性良好,R2为0.999,线性范围2～64 m...     

Studies on the aroma of cupuassu liquor by headspace solid-phase microextraction and gas chromatography

Headspace solid-phase microextraction (HS-SPME) coupled to gas chromatography with ion trap mass spectrometric detection and with atomic emission detection (GC-AED) was employed to identify possible odor-impact volatile organic compounds in cupuassu (Theobroma grandiflorum Spreng) liquor, as well as to quantify alkylpyrazines present in these samples. SPME fibers coated with 100 microm polydimethylsiloxane (PDMS), 65 microm PDMS-divinylbenzene (DVB) and 75 microm Carboxen (CAR)-PDMS were tested, the later being chosen for the optimized extraction procedure. The principal compounds found in the sample headspace were 3-methylbutanal, dimethylsulfide, dimethyldisulfide, beta-linalool and several alkylpyrazines (notably tetramethylpyrazine). The procedure for quantitation of the alkylpyrazines, using GC-AED for their separation and detection, allowed the detection of microg g(-1) levels of the analytes in the samples, with acceptable precision (R.S.D. less than 10%).     

Determination of volatile organic hydrocarbons in water samples by solid-phase dynamic extraction

In the present study a headspace solid-phase dynamic extraction method coupled to gas chromatography–mass spectrometry (HS-SPDE-GC/MS) for the trace determination of volatile halogenated hydrocarbons and benzene from groundwater samples was developed and evaluated. As target compounds, benzene as well as 11 chlorinated and brominated hydrocarbons (vinyl chloride, dichloromethane, cis-1,2-dichloroethylene, trans-1,2-dichloroethylene, carbon tetrachloride, chloroform, trichloroethylene, tetrachloroethylene, bromoform) of environmental and toxicological concern were included in this study. The analytes were extracted using a SPDE needle device, coated with a poly(dimethylsiloxane) with 10% embedded activated carbon phase (50-μm film thickness and 56-mm film length) and were analyzed by GC/MS in full-scan mode. Parameters that affect the extraction yield such as extraction and desorption temperature, salting-out, extraction and desorption flow rate, extraction volume and desorption volume, the number of extraction cycles, and the pre-desorption time have been evaluated and optimized. The linearity of the HS-SPDE-GC/MS method was established over several orders of magnitude. Method detection limits (MDLs) for the compounds investigated ranged between 12 ng/L for cis-dichloroethylene and trans-dichloroethylene and 870 ng/L for vinyl chloride. The method was thoroughly validated, and the precision at two concentration levels (0.1 mg/L and a concentration 5 times above the MDL) was between 3.1 and 16% for the analytes investigated. SPDE provides high sensitivity, short sample preparation and extraction times and a high sample throughput because of full automation. Finally, the applicability to real environmental samples is shown exemplarily for various groundwater samples from a former waste-oil recycling facility. Groundwater from the site showed a complex contamination with chlorinated volatile organic compounds and aromatic hydrocarbons. Figure SPDE Principle     

Screening of volatile composition from Portuguese multifloral honeys using headspace solid-phase microextraction-gas chromatography-quadrupole mass spectrometry

The volatile composition from four types of multifloral Portuguese (produced in Madeira Island) honeys was investigated by a suitable analytical procedure based on dynamic headspace solid-phase microextraction (HS-SPME) followed by thermal desorption gas chromatography-quadrupole mass spectrometry detection (GC-qMS). The performance of five commercially available SPME fibres: 100 μm polydimethylsiloxane, PDMS; 85 μm polyacrylate, PA; 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane, DVB/CAR/PDMS (StableFlex); 75 μm carboxen/polydimethylsiloxane, CAR/PDMS, and 65 μm carbowax/divinylbenzene, CW/DVB; were evaluated and compared. The highest amounts of extract, in terms of the maximum signal obtained for the total volatile composition, were obtained with a DVB/CAR/PDMS coating fibre at 60 °C during an extraction time of 40 min with a constant stirring at 750 rpm, after saturating the sample with NaCl (30%). Using this methodology more than one hundred volatile compounds, belonging to different biosynthetic pathways were identified, including monoterpenols, C₁₃-norisoprenoids, sesquiterpenes, higher alcohols, ethyl esters and fatty acids. The main components of the HS-SPME samples of honey were in average ethanol, hotrienol, benzeneacetaldehyde, furfural, trans-linalool oxide and 1,3-dihydroxy-2-propanone.     

Comparison of Needle Concentrator with SPME for GC Determination of Benzene, Toluene, Ethylbenzene, and Xylenes in Aqueous Samples

A method of solventless extraction of volatile organic compounds from aqueous samples has been developed and validated. A new arrangement in which the internal volume of a needle capillary adsorption trap is completely filled with Porapak Q, as adsorbent material, and wet alumina, as a source of desorptive water vapor flow, is presented. The device has been used for head-space sampling of benzene, toluene, ethylbenzene, and xylenes (BTEX) from water samples and compared with solid-phase microextraction. Under the same sampling conditions the analytical characteristics of the device for the BTEX compounds are better than those of solid-phase microextraction. Limits of detection and quantification are below 0.5 μ g L⁻¹.     

Elimination of matrix effects for headspace solid-phase microextraction of important volatile compounds in red wine using a novel coating

In this paper, hydroxy-terminated silicone oil-butyl methacrylate-divinylbenzene (OH-TSO-BMA-DVB) copolymer was first synthesized and used as stationary phase with the aid of γ-methacryloxypropyltrimethoxylsilane (KH-570) as bridge in solid-phase microextraction (SPME) using sol–gel method and cross-linking technique. It has high extraction efficiency for both polar alcohols and fatty acids and nonpolar esters in comparison with commercial PDMS, PDMS-DVB and PA fibers. A simple and sensitive headspace SPME-gas chromatography (HS-SPME-GC) method using the novel fiber was presented for the simultaneous analysis of both polar alcohols and fatty acids and nonpolar esters in wine. To check the matrix effects, various model wine matrices, including distilled water; 11.5% ethanol/water (v/v) solution; a concentrated synthetic wine; a ‘volatile-free’ wine and a real wine were investigated in detail. Matrix effects were compensated for by using internal standard method and selecting the ‘volatile-free’ wine as working standard. The method presented in this study showed satisfactory linearity, precision, detection limits and accuracy. The recoveries obtained ranged from 85.87 to 104.2%, and the relative standard deviation values were below 9%. The results obtained indicated that the present method is a validated and accurate procedure for the simultaneous determination of both polar and nonpolar aroma compounds in wine.     

Optimisation of a simple and reliable method based on headspace solid-phase microextraction for the determination of volatile phenols in beer

A simple, accurate and sensitive method based on headspace solid-phase microextraction (HS-SPME) coupled to gas chromatography–tandem mass spectrometry (GC–MS/MS) was developed for the analysis of 4-ethylguaiacol, 4-ethylphenol, 4-vinylguaiacol and 4-vinylphenol in beer. The effect of the presence of CO₂ in the sample on the extraction of analytes was examined. The influence on extraction efficiency of different fibre coatings, of salt addition and stirring was also evaluated. Divinylbenzene/carboxen/polydimethylsiloxane was selected as extraction fibre and was used to evaluate the influence of exposure time, extraction temperature and sample volume/total volume ratio (V_s/V_t) by means of a central composite design (CCD). The optimal conditions identified were 80 °C for extraction temperature, 55 min for extraction time and 6 mL of beer (V_s/V_t 0.30). Under optimal conditions, the proposed method showed satisfactory linearity (correlation coefficients between 0.993 and 0.999), precision (between 6.3% and 9.7%) and detection limits (lower than those previously reported for volatile phenols in beers). The method was applied successfully to the analysis of beer samples. To our knowledge, this is the first time that a HS-SPME based method has been developed to determine simultaneously these four volatile phenols in beers.     

Determination of odour-causing volatile organic compounds in cork stoppers by multiple headspace solid-phase microextraction

Multiple headspace solid-phase microextraction (MHS-SPME) coupled with gas chromatography-mass spectrometry has been applied in order to determine 2,4,6-trichloroanisole (2,4,6-TCA), guaiacol, 1-octen-3-ol and 1-octen-3-one in three samples of cork stoppers. These compounds are responsible for cork taint in wine and can modify the organoleptic properties of bottled wine. Variables such as temperature, addition of water, extraction time, and amount of cork were studied. The extractions were performed with a 50/30 microm divinylbenzene-carboxen-polydimethylsiloxane (DVB-CAR-PDMS) fibre for 45 min at 100 degrees C using 20 mg of cork. For calibration, 50 microL of VOC aqueous solutions were used and the extraction were carried out for 45 min at 75 degrees C. The limits of detection of the method expressed as ng of VOC per g of cork were 0.3 for 2,4,6-TCA, 7.5 for guaiacol, 1.7 for 1-octen-3-one and 1.9 for 1-octen-3-ol. Relative standard deviation of replicate samples was less than 10%. Significant losses of analytes were observed when the samples were ground at room temperature. Finally, a recovery study was performed and the MHS-SPME results were validated using Soxhlet extraction results.     

Detection of ethanol in human body fluids by headspace solid-phase micro extraction (SPME)/capillary gas chromatography

Summary Ethanol has been found extractable from human whole blood and urine samples by headspace solid-phase micro extraction (SPME) with a Carbowax/divinylbenzene-coated fiber. After heating a vial containing the body fluid sample with ethanol, and isobutanol as internal standard (IS) at 70°C in the presence of (NH₄)₂SO₄, a Carbowax/divinylbenzene-coated SPME fiber was exposed in the headspace of the vial to allow adsorption of the compounds. The fiber needle was then injected into a middle-bore capillary gas chromatography (GC) port. The headspace SPME-GC gave intense peaks for both compounds; a small amount of background noises appeared, but did not interfere with the detection of the compounds. Recoveries of ethanol and IS were 0.049 and 0.026% for whole blood, respectively, and 0.054 and 0.085% for urine, respectively. The calibration curves for ethanol showed excellent linearity in the range of 80–5000 mg L^–1 for whole blood and 40–5000 mg L^–1 for urine; the detection limits for both samples were 20 and 10 mg L^–1, respectively. The data on actual determination of ethanol after the drinking of beer are also presented for two subjects.     

A new porous-layer activated-charcoal-coated fused silica fiber: Application for determination of BTEX compounds in water samples using headspace solid-phase microextraction and capillary gas chromatography

Summary Extra-fine powdered activated charcoal has been used as stationary phase (coating layer) in solid-phase microextraction (SPME). The efficiency and reliability of the prepared device have been investigated for the extraction of some volatile organic compounds such as benzene, toluene, ethylbenzene and xylene isomers (BTEX) from the headspace of water samples. Monitoring of the extracted compounds and further quantitative analysis of the real samples have been performed by capillary GC-FID. Effects of several factors such as temperature, addition of salt, and stirring speed on extraction efficiency and exposure time have been studied. Under optimum conditions, extraction recoveries for these compounds from 50 mL water were >95%. The calibration graphs were linear in the range 5 to 10⁴ pg mL⁻¹ and the detection limit for each BTEX compound was 1.5–2 pg mL⁻¹. The results obtained by use of this porous layer activated charcoal (PLAC)-coated fiber have also been compared with results reported in the literature by use of a polydimethylsiloxane (PDMS)-coated fiber. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Determination of very volatile organic compounds in environmental water by injection of a large amount of headspace gas into a gas chromatograph

An injection method for a large amount of headspace gas which enables determination of trace amounts of very volatile organic compounds (VVOCs), dichlorodifluoromethane, chloromethane, vinyl chloride, bromomethane, chloroethane and trichlorofluoromethane in all kinds of environmental water was developed. A gas phase equilibrated with the water phase in a vial was purged with helium for a short time. The VVOCs were then introduced into a trapping tube packed with Tenax TA, which had been cooled using carbon dioxide. After trapping, the VVOCs were thermally desorbed and put into a GC–MS system for subsequent analysis. This method is applicable to various types of samples.