Phase behavior of some polyamic acid plus ether systems

Polyamic acids, prepared by reacting 3,3′,4,4′-benzophenone tetracarboxylic acid dianhydride with 3,3′-diaminobenzophenone and with 4,4′-diaminobenzophenone, were dissolved in tetrahydrofuran and in bis(2-methoxyethyl) ether at concentrations up to 40 wt %. Reversible phase separation was observed when these systems were heated. Evidence cited indicates that all observed phases are isotropic, notwithstanding the fact that a number of aromatic polyamides are mesogenic.     

Porous cobalt hydroxide film electrodeposited on nickel foam with excellent electrochemical capacitive behavior

A new porous cobalt hydroxide film has been successfully electrodeposited on nickel foam from 0.1?M cobalt nitrate electrolyte at ?1.0?V vs. SCE without adding any surfactant. The microstructure and surface morphology of prepared cobalt hydroxide films were physically characterized by X-ray diffraction analysis and scanning electron microscopy. The results indicate that an interlaced network structure was obtained. The effects of electrodeposition time, deposition potential, and different substrates on the specific capacitance and microstructure of prepared porous ??-Co(OH)₂ thin film were systematically studied. The results indicate that the film deposited on nickel foam at ?1.0?V has excellent electrochemical properties. A maximum specific capacitance of 1473?F?g^?1 could be achieved at a current density of 2?A?g^?1.     

Fabrication of Ni nanoparticles by selective oxidation of permalloy thin film during imidization of polyamic acid

Ni nanoparticles embedded in a polyimide (PI) matrix were fabricated by selectively oxidizing a layer of Ni(80)Fe(20) metal film sandwiched between two PI precursor layers. Ni nanoparticles, formed in a monolayer between two PI layers, had an average particle size of approximately 5 nm. X-Ray photoelectron spectroscopy confirmed that Fe in the film was preferentially consumed, resulting in the formation of Ni nanoparticles.     

Simple method for preparation of porous polyimide film with an ordered surface based on in situ self-assembly of polyamic acid and silica microspheres

In this Article, we addressed a facile method for the fabrication of porous polyimide film with an ordered surface based on the solvent-evaporation-assisted in situ self-assembly of polyamic acid (PAA, precursor of polyimide) and silica microspheres during vacuum-drying of PAA/silica colloid solution. Hydroxyl groups on the surface of silica microspheres have strong hydrogen-bonding with PAA chains, which improve the dispersion of silica microspheres in PAA/DMF solution and further help the self-assembly of PAA/silica colloid solution via solvent evaporation. The approach is simple, neither the preparation of special template nor complex preparation process and precise control over condition is necessary. Furthermore, the method could be employed for mass production of ordered porous polyimide films, and by changing the content and size of silica microspheres, the pore size and porous structure of the porous polyimide films could be tunable. The wettability behavior of the as-prepared porous polyimide films is also studied; the ordered surface topography of the porous polyimide films could change the wettability from hydrophilicity to hydrophobicity.     

Optically controlled resonance energy transfer: mechanism and configuration for all-optical switching

In a molecular system of energy donors and acceptors, resonance energy transfer is the primary mechanism by means of which electronic energy is redistributed between molecules, following the excitation of a donor. Given a suitable geometric configuration it is possible to completely inhibit this energy transfer in such a way that it can only be activated by application of an off-resonant laser beam: this is the principle of optically controlled resonance energy transfer, the basis for an all-optical switch. This paper begins with an investigation of optically controlled energy transfer between a single donor and acceptor molecule, identifying the symmetry and structural constraints and analyzing in detail the dependence on molecular energy level positioning. Spatially correlated donor and acceptor arrays with linear, square, and hexagonally structured arrangements are then assessed as potential configurations for all-optical switching. Built on quantum electrodynamical principles the concept of transfer fidelity, a parameter quantifying the efficiency of energy transportation, is introduced and defined. Results are explored by employing numerical simulations and graphical analysis. Finally, a discussion focuses on the advantages of such energy transfer based processes over all-optical switching of other proposed forms.     

A study of the curing behavior of polyamic acid coated on a Cu or Zn layer

ZnO and Cu₂O nanoparticles can be formed through the thermal decomposition of the complex between Zn or Cu with polyamic acid (PAA), accompanying with the formation of polyimide (PI). Transmission electron microscopy (TEM) analysis showed that the formation of ZnO nanoparticles needs a longer curing time than that of Cu₂O. Fourier transform infrared spectroscopy (FT-IR) characterization shows that both Zn and Cu will delay the imidization process of PAA. However, the retarding degree of imidization process is higher for Zn than that of Cu. Further investigation showed the structure of Zn–PAA complex is different from that of Cu–PAA, which is the reason for the difference of initial imidization temperature. Thermogravimetric and differential thermal analysis (TG–DTA) characterization agrees well with the results of FT-IR. Also, the thermal decomposition temperature of the polyimide was changed by the involvement of Zn or Cu during curing.     

A new pseudo rubrene analogue with excellent film forming ability

A novel pseudo rubrene analogue,6,11-di(thiophen-2-yl)-tetracene-5,12-dione (DTTDO) was synthesized,in which two thienyl groups and two carbonyl groups replacing four phenyl groups in the rubrene molecule were connected to the backbone of tetracene.This compound was characterized by single crystal X-ray structure analysis,thermogravimetric analysis,absorption spectra and electrochemical measurements.Unlike rubrene,DTTDO exhibited excellent film forming ability by normal vacuum deposition,indicating its prom...     

冠醚和卟啉与花生酸混合单分子膜行为研究

本文将3'-正十五烷基苯并15-冠-5和六种无脂链难于直接成膜的四苯基卟啉与花生酸混合形成单分子膜。结果表明, 冠醚被嵌进而卟啉被挤出花生酸单分子层。卟啉-花生镉LB膜的可见吸收光谱指出卟啉分子成团聚集。扫描电镜观察了卟啉-花生酸镉混合LB膜的表面形貌, 在膜表面上无金涂层时直接测到了混合膜的相分离。     

Modification of epoxy novolak resin with polyamic acid,investigation of cocuring mechanism

The processes of thermal curing in the epoxy novolak resin-polyamic acid system were investigated by means of high-temperature FTIR spectroscopy. It was shown that, under the conditions studied, the formation of copolymer took place, and the mechanism of cocuring changed depending on the concentration of modifying agent.     

Kinetic models for solution imidization of polyamic acid containing naphthalene‐pendant group

The kinetics and mechanisms of the solution imidization of polyamic acid resulting from a diamine, bis(4‐aminophenoxy‐3,5‐dimethylphenyl)naphthylmethane, and a dianhydride, 3,3′4,4′‐diphenylsulfonetetracarboxylic dianhydride, were studied at three various temperatures (145, 165, and 180 °C). The results were confirmed by means of ¹H NMR and gel permeation chromatography (GPC). Kinetic parameters were obtained by an isothermal study, and the results were quite close to second‐order kinetics for the homogeneous solution imidization. In addition, Carother's equation, Mark–Houwink theory, and GPC were used to explain the molecular weight of the imidization processes. The apparent activation energy (E_a) was 104 KJ/mol, and the pre‐exponential factor (k₀) was 3.48 × 10¹⁴. The proposed kinetic mechanism is in good agreement with the kinetic models. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4139–4151, 2001     

Thermal behavior and film formation from an organogermanium polymer/nanoparticle precursor

In situ high-resolution transmission electron microscopy (HRTEM) was used to investigate the effect of heating on an organo-Ge polymer/nanoparticle composite material containing 4-8 nm diameter alkyl-terminated Ge nanoparticles. The product was obtained from the reduction of GeCl4 with Na(naphthalide) with subsequent capping of the -Cl surface with n-butyl Grignard reagent. The in situ HRTEM micrographs show that the product undergoes significant changes upon heating from room temperature to 600 degrees C. Two pronounced effects were observed: (i) Ge nanoparticles coalesce and remain crystalline throughout the entire temperature range, and (ii) the organo-Ge polymer acts as a source for the in situ formation of additional Ge nanoparticles. The in situ-formed Ge nanoparticles are approximately 2-3 nm in diameter. These in situ-formed nanoparticles (2-3 nm) are so dense that, together with the original ones, they build up an almost continuous crystalline film in the temperatures between 300 and 500 degrees C. Above 480 degrees C, melting of the in situ formed Ge nanoparticles (2-3 nm) is observed, while nanoparticles greater than 5 nm remain crystalline. After cooling to room temperature, the 2-3 nm Ge nanoparticles recrystallized.     

In situ PEI and formic acid directed formation of Pt NPs/MWNTs hybrid material with excellent electrocatalytic activity

A hybrid material based on Pt nanoparticles (Pt NPs) and multi-walled carbon nanotubes (MWNTs) was fabricated with the assistance of PEI and formic acid. The cationic polyelectrolyte PEI not only favored the homogenous dispersion of carbon nanotubes (CNTs) in water, but also provided sites for the adsorption of anionic ions PtCl₄²⁻ on the MWNTs’ sidewalls. Deposition of Pt NPs on the MWNTs’ sidewalls was realized by in situ chemical reduction of anionic ions PtCl₄²⁻ with formic acid. The hybrid material was characterized with TEM, XRD and XPS. Its excellent electrocatalytic activity towards both oxygen reduction in acid media and dopamine redox was also discussed.     

Honeycomb-patterned film segregated with phenylboronic acid for glucose sensing

Phenylboronic acid (PBA)-functionalized materials have attracted considerable attention because of their potential applications in many fields. In this paper, we report a PBA-segregated honeycomb-patterned porous film (HPPF) for glucose sensing. Polystyrene-block-poly(acrylic acid-co-acrylamidophenylboronic acid) with different contents of PBA pendants was synthesized via atom transfer radical polymerization (ATRP) followed by a coupling reaction. PBA-functionalized HPPFs were then fabricated by the breath figure method. Results indicate that the composition of the copolymers and the relative humidity play key roles in pore size and regularity of the films. Using Alizarin Red S (ARS) that does not emit fluorescence itself as a fluorescent probe, it is confirmed that PBA pendants are mainly distributed at the pore wall, instead of at the outer surface of HPPFs. This distribution is caused by the segregation of hydrophilic PBA-blocks toward the condensed water droplets, which act as templates for the pore formation. Quartz crystal microbalance results demonstrate that the PBA-functionalized HPPFs show high sensitivity in glucose sensing, which is owing to the segregation of PBA pendants at the pore wall as well as the large specific surface area of the porous films.     

Interaction and incorporation of ovalbumin with stearic acid monolayer: Langmuir-Blodgett film formation and deposition

In this communication, the surface activity of the ovalbumin (OVA) at the air/water interface was studied to establish the nature of the interaction with the stearic acid (SA) monolayer, based on Langmuir–Blodgett (LB) technique. The interaction was monitored by studying the time (t) variation of surface pressure (π) at constant area (A). The growth of π with time indicates a positive association between the SA and the OVA molecules. The surface compressibility analysis has been performed to specify the phase transition of OVA–SA mixed monolayer. Incorporation/association of OVA within the SA monolayer led to noteworthy changes in surface compressibility and was surface pressure as well as protein concentration dependent. Both the hydrophobic and the Vander wall type interactions are found to be responsible for the association. The quenching of tyrosine band in tryptophan excitation spectrum is observed in steady-state fluorescence spectroscopy. This suggests that the tyrosine is the probable binding site with SA. Due to incorporation of SA, the energy transfer from tyrosine to tryptophan is hindered. At higher pressure, OVA tend to squeeze out from the SA monolayer. The high-resolution field emission scanning electron microscope (FE-SEM) image confirms this observation. Aggregated protein structure observed at high pressure indicates unfolding of protein.     

A facile method to prepare fluorine-free film transfer paper with excellent oil resistance

Cellulose - Environmental and health concerns are driving food packaging to reduce the use of poly- or perfluorinated compounds and petroleum-based polymers. Here, we successfully obtained good...     

Surface behavior and film formation analysis of sisal fiber coated by poly(methyl methacrylate) ultrathin film

Admicellar polymerization was used to modify a sisal fiber surface with poly(methyl methacrylate) (PMMA) in order to improve the compatibility between the sisal fiber and the surrounding polymeric matrix in a composite. The effect of the amount of monomer (methyl methacrylate) and initiator (sodium persulfate) on the hydrophobicity behavior and PMMA film formation of the admicellar-treated sisal surface was studied. The increase in the hydrophobicity of the admicellar-treated sisal fiber was examined by flotation testing, moisture absorption, and electrostatic charge or zeta (ζ) potential. The amount of PMMA film formed on the sisal surface was investigated by the weight loss of the admicellar-treated sisal extracted by acetone and chloroform; and the thermal degradation was studied by thermogravimetric analyses. The admicellar-treated sisal could float on the surface of water for longer than half an hour, and its moisture absorption decreased. The ζ potential of its surface also showed a significant change compared to the untreated sisal. The results from the weight loss indicated that the amount of PMMA formed on the sisal fiber surface depended on the amount of monomer and initiator. The Fourier transform infrared spectrum of the admicellar-treated sisal showed the characteristic peaks of PMMA and the scanning electron micrograph of the treated sisal was clearly different from the untreated sisal, confirming that there was a thin film coating on the admicellar-treated sisal fiber.