Comparison of electrocatalytic characterization of Ti/Sb-SnO<Subscript>2</Subscript> and Ti/F-PbO<Subscript>2</Subscript> electrodes

Electrocatalytic oxidation is a promising process for degrading toxic and biorefractory organic pollutants in wastewater treatment. Selection of electrode materials is crucial for electrochemical oxidation process. In this study, Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes were chosen to compare their electrocatalytic characterization, which were prepared by electrodeposition and thermal decomposition method, respectively. The surface morphology and crystal structure of two electrodes were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The linear polarization curves show that Ti/Sb-SnO₂ electrodes possess higher oxygen evolution overpotential than Ti/F-PbO₂ electrodes. But the stability and corrosion resistance ability of Ti/F-PbO₂ electrode was higher than that of Ti/Sb-SnO₂ electrode. The electrocatalytic activity of Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes was examined for the electrochemical oxidation of malachite green (MG). The bulk electrolysis shows that the Ti/Sb-SnO₂ electrodes exhibit the higher electrocatalytic activity for the degradation of MG than Ti/F-PbO₂ electrodes, and the degradation process is good fitting for the pseudo-first order reaction. The higher electrocatalytic activity of Ti/Sb-SnO₂ electrodes can be attributed to the higher oxygen evolution overpotential.     

LaNi<Subscript>0.5</Subscript>Ti<Subscript>0.5</Subscript>O<Subscript>3</Subscript>/CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>-based sensor for sensitive determination of paracetamol

A novel electrochemical sensor based on LaNi_0.5Ti_0.5O₃/CoFe₂O₄ nanoparticle-modified electrode (LNT–CFO/GCE) for sensitive determination of paracetamol (PAR) was presented. Experimental conditions such as the concentration of LNT–CFO, pH value, and applied potential were investigated. Under the optimum conditions, the electrochemical performances of LNT–CFO/GCE have been researched on the oxidation of PAR. The electrochemical behaviors of PAR on LNT–CFO/GCE were investigated by cyclic voltammetry. The results showed that LNT–CFO/GCE exhibited excellent promotion to the oxidation of PAR. The over-potential of PAR decreased significantly on the modified electrode compared with that on bare GCE. Furthermore, the sensor exhibits good reproducibility, stability, and selectivity in PAR determination. Linear response was obtained in the range of 0.5 to 901 μM with a detection limit of 0.19 μM for PAR.     

TiO<Subscript>2</Subscript> nanotube arrays based DSA electrode and application in treating dye wastewater

Dimensionally stable anode (DSA) of antimony-doped tin dioxide electrode based on TiO₂-nanotube arrays (NTs) has been successfully fabricated through thermal decomposition. The surface morphology and composition of the electrodes were characterized by using scanning electron microscopy and X-ray diffraction. Methyl orange (MO) was used as a model pollutant to investigate the electrochemical properties of these two electrodes. The optimized anodic oxidation voltage and time for TiO₂-nanotubes array based DSA electrode is 60 V and 10 min, respectively. The results show that Ti/TiO₂–NTs/Sb–SnO2 electrode has an increase of 100 mV in oxygen evolution overpotential and the service life is 56% longer than that of the traditional DSA electrode. Under the optimum conditions, MO solution decolorization rate and TOC removal rate reached approximately 100 and 80%, respectively. Study suggested that the as-prepared Ti/TiO₂–NTs/Sb–SnO2 DSA electrode exhibits high activity for degradation of organic pollutant with high concentration.     

Oxygen evolution on Ti/Co<Subscript>3</Subscript>O<Subscript>4</Subscript>-coated electrodes in alkaline solution

The electrochemical performances of Co₃O₄ nanopowders, obtained by the sol-gel method, were investigated and compared with those of commercial Co₃O₄ powders, for oxygen evolution reaction in alkaline solution. The active oxide powder was mixed with teflon and assembled on Ti substrate to form thin catalyst film. Cyclic voltammetry, polarization curves, and electrochemical impedance spectroscopy were used to assess the mechanism of oxygen evolution reaction, chemical structure, and morphology of the catalyst. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

Facile synthesis of Fe@Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanowires as O<Subscript>2</Subscript> electrode for high-energy Li-O<Subscript>2</Subscript> batteries

Fe@Fe₂O₃ core-shell nanowires were synthesized via the reduction of Fe³⁺ ions by sodium borohydride in an aqueous solution with a subsequent heat treatment to form Fe₂O₃ shell and employed as a cathode catalyst for non aqueous Li-air batteries. The synthesized core-shell nanowires with an average diameter of 50–100 nm manifest superior catalytic activity for oxygen evolution reaction (OER) in Li-O₂ batteries with the charge voltage plateau reduced to ～3.8 V. An outstanding performance of cycling stability was also achieved with a cutoff specific capacity of 1000 milliampere hour per gram over 40 cycles at a current density of 100 mA g^?1. The excellent electrochemical properties of Fe@Fe₂O₃ as an O₂ electrode are ascribed to the high surface area of the nanowires’ structure and high electron conductivity. This study indicates that the resulting iron-containing nanostructures are promising catalyst in Li-O₂ batteries.     

Oxidation of toluene on Bi-doped PbO<Subscript>2</Subscript> studied by electrochemical impedance spectroscopy and UV spectrophotometry

Oxidation of organics in the potential region of O₂ evolution is supposed to proceed through the oxidation of water to hydroxyl radicals, which then may either be further oxidized to give molecular oxygen or interact with organic molecules in an oxygen transfer reaction. Therefore, the electrode material must ensure (1) the preferential adsorption of the organic compound, (2) the production of adsorbed hydroxyl radicals able to react with this compound in a selective oxidation reaction (with as little as possible oxygen evolution), and (3) a long-term stability. In the present paper, the oxidative decomposition of toluene in sulfuric acid solution on PbO₂ coatings deposited on Ti substrate from acidic nitrate + fluoride baths containing Pb²⁺ and Bi³⁺ is investigated by voltammetry, electrochemical impedance spectroscopy, and UV spectrophotometry. The chemical composition and structure of the catalytic coatings is characterized with X-ray photoelectron spectroscopy and X-ray diffraction. The catalytic activity is estimated both from current density vs potential and polarization resistance vs potential plots using measurements on the same electrodes in sulfuric acid without toluene to eliminate the oxygen evolution reaction that proceeds in parallel to the oxidation of toluene. A skeletal reaction mechanism of the process is proposed to account for the steady-state and transient response of the catalytic electrodes during oxidation of toluene.     

Oxygen isotope exchange between the gas-phase and the electrochemical cell O<Subscript>2</Subscript>, Pt | YSZ | Pt,O<Subscript>2</Subscript> under conditions of applied potential difference

The kinetics of oxygen isotope exchange between gas-phase oxygen and the electrochemical cell O₂, Pt | ZrO₂ + 10 mol % Y₂O₃ (YSZ) | Pt, O₂ with applied potential difference (ΔU = ±1.2 V) is studied in the temperature range of 600–800°С and the oxygen pressure interval of 3–13 kPa. An original design of a vacuum electrochemical cell with the separated gas space is put forward for studying how the potential difference on the electrochemical cell influences the kinetics of interaction of gas-phase oxygen with the gas electrode O₂, Pt | YSZ in the electrochemical cell. It is shown that the oxygen interphase exchange rate is the higher the more negative the charge on the electrode studied; moreover, the mechanism of gas-phase oxygen exchange with the gas electrode O₂, Pt | YSZ in the electrochemical cell depends fundamentally on the electrode charge sign. The possible reasons for the revealed differences are discussed; the corresponding models are proposed.     

Voltammetric determination of vitamin B<Subscript>6</Subscript> (pyridoxine) at a graphite screen-printed electrode modified with graphene oxide/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript> nanocomposite

The preparation and study of electrochemical properties of a graphite screen-printed electrode (SPE) modified with the GO/Fe₃O₄@SiO₂ (GO is graphene oxide) nanocomposites are described. The morphologies of the GO/Fe₃O₄@SiO₂ nanocomposites were examined by scanning electron microscopy. The electrochemical oxidation of vitamin B₆ (pyridoxine) on SPE modified with the GO/Fe₃O₄@SiO₂ nanocomposite was investigated by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. Under optimum conditions (pH 7.0), the vitamin B₆ oxidation at the surface of the modified SPE occurs at a potential about 190 mV less positive than that at the unmodified SPE. A linear voltammetric response for vitamin B₆ was obtained in the concentration range 1.0?10 ⁶—9.0?10 ⁴ mol L^–1 with a detection limit of 5.2?10 ⁷ mol L^–1 using differential pulse voltammetry. The developed sensor was also successfully applied for determination of trace level of vitamin B₆ in both the standard vitamin B₆ sample and biological samples (urine).     

Study of electrochemical behavior of the Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles in aprotic media

Peculiarities of electrochemical behavior of the Fe₃O₄ magnetic nanoparticles immobilized on the surface of a platinum electrode in aprotic organic media were investigated. Possible scheme of electrochemical behavior of nanoparticles depending on pre-electrolysis potential (–1.3,–2.5 V) was suggested. The effect of pre-electrolysis time, potential scan rate and nature of supporting electrolyte on the processes investigated was determined. A linear dependence of electrochemical oxidation signal versus the concentration of nanoparticles in modifying suspension in the concentration range of 0.05—0.5 g L^–1 was observed. The results of the performed research allow using magnetite nanoparticles as a direct signal-generating label in electrochemical immunoassay.     

Electrodeposition of thin Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> films

The electrochemical behavior of copper(II), zinc(II), and thiosulfate (S₂O₃ ^2-) ions on the molybdenum electrode in individual 0.2 М sodium sulfate solutions (рН 6.7) and with addition of either 0.1 М tartaric acid (рН 4.6) or 0.1 М citric acid (рН 4.7) is studied. A one-step electrochemical method is developed for the deposition of thin Cu₂ZnSnS₄ films, which is carried out on the molybdenum electrode at a constant potential in sodium sulfate solutions containing tartaric acid. The effect of the concentration of electrolyte components on the chemical composition of Cu₂ZnSnS₄ films is determined. The phase composition is confirmed by the Raman spectroscopy data. The surface morphology of synthesized films is studied by means of scanning-electron and atomic-force microscopes. The photoelectrochemical characteristics of Cu₂ZnSnS₄ films are determined. Samples of these coatings on the Mo electrode are found to be highly photosensitive.     

La<Subscript>0.1</Subscript>Ca<Subscript>0.9</Subscript>MnO<Subscript>3</Subscript>/Co<Subscript>3</Subscript>O<Subscript>4</Subscript> for oxygen reduction and evolution reactions (ORER) in alkaline electrolyte

Non-precious metal bifunctional catalysts are of great interest for metal–air batteries, electrolysis, and regenerative fuel cell systems due to their performance and cost benefits compared to the Pt group metals (PGM). In this work, metal oxides of La_0.1Ca_0.9MnO₃ and nano Co₃O₄₇ catalyst as bifunctional catalysts were used in oxygen reduction and evolution reactions (ORER). The catalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and N₂ adsorption isotherms. The electrocatalytic activity of the perovskite-type La_0.1Ca_0.9MnO₃ and Co₃O₄ catalysts both as single and mixtures of both were assessed in alkaline solutions at room temperature. Electrocatalyst activity, stability, and electrode kinetics were studied using cyclic voltammetry (CV) and rotating disk electrode (RDE). This study shows that the bifunctional performance of the mixed La_0.1Ca_0.9MnO₃ and nano Co₃O₄ was superior in comparison to either La_0.1Ca_0.9MnO₃ or nano Co₃O₄ alone for ORER_. The improved activity is due to the synergistic effect between the La_0.1Ca_0.9MnO₃ and nano Co₃O₄ structural and surface properties. This work illustrates that hybridization between these two metal oxides results in the excellent bifunctional oxygen redox activity, stability, and cyclability, leading to a cost-effective application in energy conversion and storage, albeit to the cost of higher catalyst loadings.     

Kinetics and mechanism of carbon monoxide oxidation on the supported metal complex catalyst PdCl<Subscript>2</Subscript>-CuCl<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The kinetics of carbon monoxide oxidation with atmospheric oxygen on a PdCl₂-CuCl₂/γ-Al₂O₃ catalyst was studied at T = 27°C and an N₂-O₂-CO mixture pressure of 1 atm. The catalyst was prepared by cold impregnation. Three groups of mechanistic hypotheses are considered, and two of them are demonstrated to be consistent with kinetic data, although they differ in the roles of water and oxygen in carbon monoxide oxidation.     

Gas diffusion hindrances on Ni cermet anode in contact with Zr<Subscript>0.84</Subscript>Y<Subscript>0.16</Subscript>O<Subscript>1.92</Subscript> solid electrolyte

The electrochemical behavior of Ni cermet electrode with CeO_{2 ? x} additive in contact with YSZ electrode was studied by means of impedance spectroscopy in H₂, H₂O, CO₂, CO, He, and Ar gas media of various composition within the temperature range of 700 to 950°C. Near the equilibrium potential, the electrochemical impedance spectra of the studied electrodes indicate to three stages of electrode reaction. The polarization conductivity of the low-frequency stage of electrode reaction (σ_lf) is characterized with the following regularities: (a) temperature dependence of σ_lf has a positive slope in Arrhenius coordinates; (b) σ_lf increases upon replacement of gas mixture with lower mutual diffusion coefficient by mixture with higher mutual diffusion coefficient, while polarization conductivity values of other stages remain practically invariable; (c) concentration relationships of 1/σ_lfrecorded for constant activity of oxygen in the gas phase are linear in the 1/σ_lf vs. 1/P _{CO 2} (P _CO) coordinates; (d) no low-frequency stage of the electrode reaction is observed upon electrochemical inflow (outflow) of the gas reagents (reaction products) to (from) the test electrodes (current passing through closely pressed specimens and central specimen impedance measurement); and (e) no change in the gas flow rate affects σ_lf value. The observed regularities were explained by assuming the gas diffusion nature of the low-frequency stage of the electrode reaction. The gas diffusion layer thickness was estimated.     

Effect of pretreatment conditions on the catalytic activity of coprecipitated Ce<Subscript>0.5</Subscript>Zr<Subscript>0.5</Subscript>O<Subscript>2</Subscript> catalyst in soot oxidation

The temperature of soot oxidation and efficiency of Ce_0.5Zr_0.5O₂ catalyst depends on its morphology, which determines the area of intergranular contact between the solid substrate and the catalyst. The temperature-programmed reduction in hydrogen to 1000°C and oxidation at 500°C (redox cycles) cause the mobility of oxygen in oxide to be enhanced and decrease the temperature of soot combustion. Oxidation of soot in the air flow on the Ce_0.5Zr_0.5O₂ catalyst result in its activation. Reuse of the catalyst decreases the temperature of soot oxidation.     

Effect of CeO<Subscript>2</Subscript> on the properties of the Pd/Co<Subscript>3</Subscript>O<Subscript>4</Subscript>/cordierite catalyst in the conversion of CO,NO, and hydrocarbons

The effect of CeO₂ on the properties of the Pd/Co₃O₄-CeO₂/cordierite catalyst is a function of the method of its preparation. The catalyst obtained by the simultaneous deposition of cerium oxide and cobalt oxide showed high activity in the oxidation of CO (CO + O₂, CO + NO) and extensive oxidation of hexane (C₆H₁₄ + O₂). This behavior is due to the increased mobility of surface oxygen and increased dispersion of the catalyst components.     

The electrochemical behavior of the LaSrCuO<Subscript>4 − δ</Subscript>/Ce<Subscript>0.9</Subscript>Gd<Subscript>0.1</Subscript>O<Subscript>2 − δ</Subscript> interface

The electrochemical behavior of the LaSrCuO_{4 − δ}/Ce_0.9Gd_0.1O_{2 − δ} interface is studied by impedance spectroscopy and cyclic voltammetry methods. By analyzing the dependence of the impedance frequency spectra on the oxygen partial pressure, the rate-determining stages of oxygen exchange are determined in the temperature interval of 500–900°C. For temperatures above 700°C, the adsorption of oxygen molecules and their dissociation to oxygen atoms are shown to make a substantial contribution to the polarization resistance of the overall electrode process, besides the charge-transfer resistance.     

Electrochemical dissolution of Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> in acid solutions

The present study deals with the electrochemical reductive dissolution of Mn₃O₄, which was added to carbon-paste electroactive electrodes (CPEEs) in acid solutions. It was found that in the experimental conditions the thermodynamically stable form of manganese was . Kinetic features of the electrochemical reductive dissolution of Mn₃O₄, which was realized under potential cycling conditions (+1.0 V→−0.7 V→+1.0 V), were determined by the electrode polarization direction. It was shown that the cathodic reduction of Mn₃O₄ was accomplished in three stages. Manganese was dissolved in the supporting solution only at the third stage. The first two stages involved solid-phase reactions. The anodic cycling stage included an active dissolution of Mn₃O₄ and the lower manganese oxide (MnO) accumulated on the electrode surface during the cathodic reduction.     

Rational design of double-confined Mn<Subscript>2</Subscript>O<Subscript>3</Subscript>/S@Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocube cathodes for lithium-sulfur batteries

Due to the high specific capacities and environmental benignity, lithium-sulfur (Li-S) batteries have shown fascinating potential to replace the currently dominant Li-ion batteries to power portable electronics and electric vehicles. However, the shuttling effect caused by the dissolution of polysulfides seriously degrades their electrochemical performance. In this paper, Mn₂O₃ microcubes are fabricated to serve as the sulfur host, on top of which Al₂O₃ layers of 2 nm in thickness are deposited via atomic layer deposition (ALD) to form Mn₂O₃/S (MOS) @Al₂O₃ composite electrodes. The MOS@Al₂O₃ electrode delivers an excellent initial capacity of 1012.1 mAh g^?1 and a capacity retention of 78.6% after 200 cycles at 0.5 C, and its coulombic efficiency reaches nearly 99%, giving rise to much better performance than the neat MOS electrode. These findings demonstrate the double confinement effect of the composite electrode in that both the porous Mn₂O₃ structure and the atomic Al₂O₃ layer serve as the spacious host and the protection layer of sulfur active materials, respectively, for significantly improved electrochemical performance of the Li-S battery.     

New organic picolylamine-type ligands and electrochemical study of their complexation with Cu(MeCN)<Subscript>4</Subscript>ClO<Subscript>4</Subscript>

A series of novel organic ligands with dipicolylamine and disulfide groups connected by polymethylene, alkylaryl, alkoxyaryl, or alkoxycarbonyl linker was synthesized. The electrochemical study by cyclic voltammetry was carried out for two synthesized ligands, and the formation of the complexes with Cu(MeCN)ClO₄ in the solution or on the gold electrode surface was established. The complex of Cu^I with 1,24-bis[N,N-bis(2-pyridylmethyl)-glycinoyloxy]-12,13-dithiatetracosane chemisorbed on the Au electrode is capable of binding molecular oxygen from solution.     

Carbon paste electrode modified with Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles and BMI.PF<Subscript>6</Subscript> ionic liquid for determination of estrone by square-wave voltammetry

A carbon paste electrode (CPE) modified with Fe₃O₄ nanoparticles (Fe₃O₄ NP) and the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (IL BMI.PF₆) was employed for the electroanalytical determination of estrone (E1) by square-wave voltammetry (SWV). At the modified electrode, cyclic voltammograms of E1 in B–R buffer (pH 12.0) showed an adsorption-controlled irreversible oxidation peak at around +0.365 V. The anodic current increased by a factor of five times and the peak potential shifted 65 mV to less positive values compared with the unmodified CPE. Under optimized conditions, the calibration curve obtained showed two linear ranges: from 4.0 to 9.0 μmol L^?1 and from 9.0 to 100.0 μmol L^?1. The limits of detection (LOD) and quantification (LOQ) attained were 0.47 and 4.0 μmol L^?1, respectively. The proposed modified electrode was applied to the determination of E1 in pork meat samples. Data provided by the proposed modified electrode were compared with data obtained by UV–vis spectroscopy. The outstanding performance of the electrochemical device indicates that Fe₃O₄ NP and the IL BMI.PF₆ are promising materials for the preparation of chemically modified electrodes for the determination of E1.