Thermal resistance,microstructure and mechanical properties of type I Portland cement pastes containing low-cost nanoparticles

This study aimed to utilize laboratory-prepared nano-silica (NS) and nano-alumina (NA) as low-cost nano-oxides additions for improving the mechanical properties and thermal resistance of hardened ordinary Portland cement (OPC) pastes. NS was synthesized from rice husk ash in the absence of any surfactant, while NA was synthesized from AlCl₃ in the presence of CTAB as a surfactant. The average particle sizes of synthesized NS and NA were 30 and 40 nm, respectively. Nano-silica or nano-alumina was added to OPC as a single phase with different ratios of 0.5, 1, 2 and 3 by mass % of OPC. The physico-chemical characteristics of different OPC-NS and OPC-NA hardened pastes were studied after 1, 3, 7, 14, 28 and 90 days of hydration. The resistance of the hardened composites for firing was evaluated for specimens cured for 28 days under tap water and then fired at 300, 600 and 800 °C for 3 h. The fired specimens were cooled by two methods: gradual cooling and rapid cooling. The compressive strength test was performed for all mixes at each firing temperature. The compressive strength results revealed that the optimum addition of NS is 1, whereas the optimum addition of NA is 0.5 by mass % of OPC. XRD, TG/DTG and SEM results indicated that ill-crystalline and nearly amorphous C–S–H, C–A–S–H and C–A–H were the main hydration products.     

Small-molecule dynamics and mechanisms underlying the macroscopic mechanical properties of coordinatively cross-linked polymer networks

Specific metal-ligand coordination between bis-Pd(II) and Pt(II) organometallic cross-linkers and poly(4-vinylpyridine) in DMSO defines a three-dimensional associative polymer network. Frequency-dependent dynamic mechanical moduli of a series of four different bulk materials, measured across several decades of oscillatory strain rates, are found to be quantitatively related through the pyridine exchange rates measured on model Pd(II) and Pt(II) complexes. Importantly, the mechanism of ligand exchange in the networks is found to be the same solvent-assisted pathway observed in the model complexes, and so the bulk mechanical properties are determined by relaxations that occur when the cross-links are dissociated from the polymer backbone. It is how often the cross-links dissociate, independently of how long they remain dissociated, that determines the bulk mechanical properties. The quantitative relationship between bulk materials properties and the kinetics and mechanisms observed in model compounds holds promise for the rational, molecular design of materials with tailored mechanical properties.     

The influence of network structure on the macroscopic mechanical properties of crosslinked polymers

Neat and rubber-toughened epoxy resin systems EPN/BA and EPN/DDS with significantly different crosslink densities and glass transition temperatures were tested under widely different experimental conditions ranging from impact to long-term loading. The resulting deformation mechanisms were examined in order to ascertain the effects of network structure and toughening modifiers. Different toughening mechanisms were observed in low- and high-crosslink-density epoxy systems, modified with the same core-shell rubber particles.     

Thermal analysis and microstructure of Portland cement-fly ash-silica fume pastes

Thermal analysis (thermogravimetry and differential thermal analysis) was used with scanning electron microscopy technique to investigate the hydration mechanisms and the microstructure of Portland cement-Fly ash-silica fume mixes. Calcium silicate hydrate (C–S–H), ettringite, gehlenite hydrate (C₂ASH₈), calcium hydroxide (Ca(OH)₂) and calcium carbonate (CaCO₃) phases were detected in all mixes. In the mixes with the use of silica fume addition, there is a decrease in Ca(OH)₂ with increasing silica fume content at 5 and 10% compared to that of the reference Portland-fly ash cement paste and a corresponding increase in calcium silicate hydrate (C–S–H).     

Integrative chemistry portfolio toward designing and tuning vanadium oxide macroscopic fibers sensing and mechanical properties

Under certain synthetic conditions vanadium oxide gels are made of nanoribbons subunits. Due to this textural specificity it is possible to align the ribbons while employing an extrusion process, generating thereby vanadium oxide macroscopic fibers. In this process V₂O₅ gel is extruded through a syringe within a PVA (1% wt) solution rotating beaker. A composite fiber can be then extracted from the beaker. These as-synthesized fibers are bearing outstanding mechanical properties (20 GPa of Young modulus) addressed with transversal flexibility that alloys macroscopic knot formation. Furthermore, they appear to be excellent alcohol sensors, enable to detect 0.1 ppm of ethanol within 16 s at 40 °C, sensitivity being associated with a good selectivity. Subsequently, we were able to tune the fibers’ sensing and mechanical properties by varying the shear rate addressed to the vanadium oxide extruded gel. In order to better appreciate the correlation between fibers’ porosity, nanoribbons subunits alignment and the addressed properties (mechanical and sensing) we tuned the porosity making the use of latex nanoparticles inclusion followed by their calcinations while varying still the imposed sheer rate during the extrusion. Finally synthesis of hybrid PANI–V₂O₅ allowed reaching enhanced tenacity 12 J g^?1, concomitant with a loss of sensitivity. We show that all the parameters involved within the mechanical and sensing performances are acting within a strong partitioning mode rather than a cooperative one. Overall, these iterative synthetic approaches demonstrate once more the importance of the correlation between structures and properties, approaches where the integrative chemistry is appearing, via its versatility, as an essential tool of chemical science to conceive rationally functional architectures bearing enhanced properties.     

Effect of annealing on microstructure and mechanical properties of polypropylene random copolymer

In this work, polypropylene random copolymer (PPR) was taken as an example to study the changes of mechanical properties related to its microstructure evolution. Firstly, the toughness and fracture morphology were analyzed by notched Izod impact test and scanning electron microscope. Annealing at relative lower temperatures (<100°C), mechanical properties are slightly enhanced, which should be pointed out that significant improvements have been observed when annealing at relative higher temperatures (>100°C). Secondly, the study was conducted from the conventional differential scanning calorimetry, wide angle X-ray diffraction, and small-angle X-ray scattering to analyses the changes in the crystalline and amorphous regions. Dynamic thermomechanical analysis was employed to explore the changes of molecular mobility in samples after annealing at different temperatures. Moreover, to find out the stress transfer between the crystalline regions and the amorphous regions, we did further analysis of the typical stress–strain curves and proposed the mechanism of microstructure evolution during annealing process. The results shown that amorphous rearranged and formed thinner lamellae when annealing at relative low temperature. While annealing at higher temperatures, the mobile and rigid amorphous regions rearranged into more perfect lamellae and the density of stress transmitters was increased significantly.     

Study of the mechanical damping behavior of SBR-modified cement pastes by dynamic mechanical analyzer

Improvement in mechanical damping of SBR-modified cement pastes had been evaluated by dynamic mechanical analyzer. Specimens were fabricated and tested under 3-point flexure clamp at frequencies of 0.5–50 Hz or temperatures of ?30 to 70 °C. Significant improvement in damping was observed in cementitious-SBR composite specimens when SBR latex to cement ratio was 0.12, which is hypothesized to occur due to improvements in viscosity of cement paste. Furthermore, the SBR-modified cement pastes showed a decreased damping variation tendency with an increase of frequency. They also showed a peak damping variation tendency under the effect of the glass transition temperature. Based on the three element model, mechanical parameters are calculated by fitting the dynamic modulus of SBR-modified cement pastes.     

Crystalline microstructure and mechanical properties of crosslinked EPDM aged under gamma irradiation

The morphology and the mechanical properties at room temperature of crosslinked EPDM irradiated or not have been studied. It has been shown that these materials are composed of two phases: semicrystalline zones with a crystallinity ratio of 20% and mainly amorphous zones. The semicrystalline zones make a continuous path through the film and therefore control the mechanical properties of the material below the melting temperature. As irradiation (in the tested range of irradiation dose) and crosslinking degree have no significant influence on the arrangement and proportion of the crystalline lamellae, all samples have nearly the same mechanical behavior at small strains. At large strains, the interactions between amorphous and crystalline parts in semicrystalline zones play the main role in the mechanical response; irradiation, by degradation of these interactions, leads to a smaller hardening phenomenon and a decrease in elongation at break. From an application point of view, in spite of the low crystallinity fraction of these materials, the presence of an important number of crystallites, as evidenced by SAXS measurements, strongly limits the consequences of irradiation on the mechanical properties. However, the mechanical reinforcement strongly depending on the presence of these crystallites, it is therefore highly sensitive to temperature: this can be an important issue for the applications of these materials since their use temperature is close to the crystallite melting temperature. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 97–105, 2010     

Modication of the properties of allapinin and deoxypeganine by their mechanical treatment

The change in the physicochemical properties of plant drugs — allapinin and deoxypeganine — on their grinding in an AGO-2U activator with a regulable energy loading have been studied.Institute of the Chemistry of Plant Substances, Academy of Sciences of the Republic of Uzbekistan, Tashkent, fax (3712) 89 14 75. Translated from Khimiya Prirodnykh Soedinenii, No. 2, pp. 272–276, March–April, 1995. Original article submitted November 1, 1994.     

The role of microstructure on the mechanical properties of polyurethane foams containing thermoregulating microcapsules

Rigid polyurethane foams with up to 50 wt% of microcapsules from LDPE-EVA containing Rubitherm^®RT27 were synthesized. The influence of microcapsules on the foams density, microstructure and mechanical resistance was studied. Cell size and strut and wall thicknesses were analyzed by SEM. The relationships between densities and foam microstructures with their Young's moduli and collapse stress were found by the Gibson and Ashby formulations and the Kerner equation for mechanical properties of composites. It was found a cell structure change from polyhedral closed-cells to spherical or amorphous open-cells. A good agreement between the experimental and theoretical data was observed but requiring a cell form factor. Thus, Fitting parameters confirmed the high trend of these microcapsules to be incorporated into the foam cell walls and the form factors depicted the abrupt change of cell morphology. Thus, these equations are suitable for predicting the mechanical properties of foams containing fillers of low mechanical resistance.     

Morphology of isotactic polypropylene-polyamide 66 blends and their mechanical properties

Compounds were prepared with isotactic polypropylene (iPP) matrix and recycled polyamide 66 fibres (PA66), which were obtained as soft waste in industrial production process. Blends with pristine PA66 pellets were prepared as comparison. The blends showed the presence of PA66 particles dispersed in the PP continuous phase. Considering the incompatibility of the two polymers the addition of isotactic polypropylene grafted with maleic anhydride (iPPgMA) as compatibilizer was investigated: the blends were characterized by thermal, mechanical, dynamic-mechanical and morphological analyses. The presence of the compatibilizer significantly influences the morphology of the blends, inducing a finer dispersion and promoting interfacial adhesion. The characterization of pristine and recycled PA66 did not show a meaningful difference in the value of molecular weight, on the other hand marked differences were presented in the flexural moduli of the two materials; analogous differences were exhibited by the blends: compounds prepared with recycled PA66 showed flexural moduli higher than compatibilized blends with pristine PA66.     

Study on the microstructure and mechanical properties for epoxy resin/montmorillonite nanocomposites by positron

Positron annihilation lifetimes have been measured for epoxy resin/organic montmorillonite (OMMT) nanocomposites. Effects of different dispersion states of nano-layered OMMT on the positron annihilation parameters and the mechanical properties were studied. We found that the ortho-positronium (o-Ps) intensity decreased with increasing OMMT content, which indicated that the interaction between the host and nanofillers restrained the segmental motion, resulting in a decrease of the free volume. On the other hand, it is very interesting to observe a good correlation between the interfacial interaction and mechanical properties, suggesting that the dispersion states of OMMT and interfacial property between clay layers and matrix played an important role in determining the mechanical properties.     

Effect of the microstructure on the dye diffusion and mechanical properties of polyamide‐6 fibers

The morphology, mechanical properties, and dye diffusion of drawn and heat‐set polyamide‐6 (PA6) yarns were examined. Correlations between the microstructure of PA6 yarns and the dye diffusion coefficients and mechanical properties were established. The crystallinity of PA6 yarns was estimated with density and Fourier transform infrared spectroscopy measurements. A decrease in the γ crystallinity and an increase in the γ‐crystallite size with the draw ratio were observed and attributed to the disappearance of small crystallites and an increase in the average γ‐crystallite size population during the deformation process. The scouring treatment increased the total crystallinity, almost entirely as a result of an increase in the α fraction. Thermally induced crystallization involved increases in both crystalline phases (α and γ) and did not involve crystal‐to‐crystal transformation, whereas drawing PA6 yarns involved both crystallization of the amorphous phase in the α form and γ→α transformation. A sharp decrease in the diffusion coefficient with an increasing draw ratio of PA6 yarns was correlated with an increasing amorphous orientation. The influence of thermally induced crystallinity on the diffusion coefficient seemed exceptionally strong. The mechanical properties of PA6 yarns were examined and correlated with structural changes. It was demonstrated that the crystallinity had a direct correlation with the terminal modulus and extension at break, whereas there was no correlation with the initial modulus. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 349–357, 2007     

Study on microstructure and mechanical properties relationship of short fibers/rubber foam composites

Research on short fibers/rubber foam composites is rarely found in the literature. In this paper, microcellular rubber foams unfilled (MF), strengthened by pretreated short fibers (MFPS) and untreated short fibers (MFUS) are prepared, respectively. The microstructure and mechanical properties of the three composites have been studied via scanning electron microscope (SEM) and mechanical testing, respectively. The SEM results show that both pretreated and untreated short fibers disperse uniformly in the composites and in bidimensional orientation. Moreover, the pretreated short fibers have much better adhesion with the rubber matrix than untreated ones. The experimental results also indicate that the introduction of short fibers is mainly responsible for the great enhancement of most mechanical properties of the microcellular rubber foams, and the good interfacial adhesion of the short fibers with the matrix contributes to the more extensive improvement in the mechanical properties. It is also found that the reinforcement effect of short fibers to compressive modulus strongly depends on the density of microcellular rubber foams, the orientation of short fiber and the deformation ratio. The compressive modulus of microcellular rubber foams at the normalized density less than 0.70 and beyond 0.70 is predicted by the modified Simple Blending Model and the Halpin-Kerner Model, respectively. The theoretically predicted values are in good accordance with the experimental results.     

Dynamic mechanical and dielectric properties of phosphonylated polypentenamers and their hydrogenated derivatives

Dynamic mechanical and dielectric properties of substituted polypentenamers with phosphonate side groups and their hydrogenated derivatives have been studied. Methyl esters, acids, and salts were investigated at two concentrations, 6.5 and 11.1 mole percent. In the unhydrogenated derivatives, one principal relaxation, labeled β, is observed mechanically in the temperature range from ?160 to 100°C. This β relaxation arises from micro-Brownian segmental motion accompanying the glass transition. Its temperature is substantially affected by the substituent concentration while its breadth is affected by the chemical nature of the substituent. An extended “rubbery plateau” region exists in the acid and salt derivatives. The dielectric results generally reinforce the mechanical assignments. In the hydrogenated derivatives, three relaxations labeled α, β, and γ in order of decreasing temperature occur mechanically in this temperature range. The temperatures at which the α and β relaxations occur depend greatly on the chemical nature of the substituents, the substituent concentration, and the thermal history of the sample; while the γ relaxation appears to be independent of these variables. Suggested assignments for the relaxations observed in these polymers, based on the dual glass transition theory of Boyer for semicrystalline polymers, have been proposed. The dielectric results are consistent with the proposed assignments.     

Crystal stability and mechanical properties of drawn polymers: A statistical-mechanical approach

The partition function is formulated by the generating function method for a stacked lamellar model of alternating crystalline and amorphous layers. The random-walk problem of enumerating statistical weights for conformations of amorphous chains confined by two parallel walls is solved for the body-centered cubic lattice as a generalization of the one-wall model treated by Roe. The mean lengths of loop, tie, and cilia chains and the free energy of the system are calculated for the random-reentry and-bridge model as a function of the distance h of separation between crystal layers and as a function of the number N of loop chains in a crystal block as the basic structural element of the system. The mean length of amorphous chains decreases at a given thickness l of the crystal layers with decreasing h or with increasing N. The free energy of the system exhibits no minimum with respect to N, showing that the folded-chain crystal is thermodynamically stable, especially for relatively small l. Additionally, it is shown that another requirement for stabilizing relatively small crystals (small l) is the formation of an aggregate structure of crystals, whereas a large single-crystal (large l) is relatively stable, irrespective of h and N. Furthermore, a theoretical model is developed to calculate the force and elastic modulus of a highly deformed stacked system, assuming that the only change in the configurations of amorphous chains within the interlamellar regions is due to deformation, except for scission of tie chains having fewer segments than are needed to span the interlamellar distance of the deformed system. It becomes evident that taut tie chains are effective in increasing the modulus of the stacked system.     

The effect of thermal annealing on the microstructure and mechanical properties of magnetron sputtered hydrogenated amorphous carbon films

Hydrogenated amorphous carbon films were deposited by magnetron sputtering of a carbon target in a methane/argon atmosphere. A postdeposition annealing at 300 °C was performed and the microstructure, bonding structure and mechanical properties of the as‐deposited and annealed films were analyzed and compared directly by high‐resolution transmission electron microscopy, micro‐Raman spectroscopy, XPS, and nanoindentation. The results showed that the carbon films are quite stable upon annealing, since there are only minor changes in microstructure and chemical bonding in the amorphous matrix. The hardness of the films remained unaffected, but the elastic properties were somewhat deteriorated. In comparison to the outcomes of our previous work on the growth of fullerene‐like hydrogenated carbon films, we can state that the formation of fullerene‐like carbon structures requires different sputtering process conditions, such as a higher ion energy and/or different sputtering target. Copyright © 2011 John Wiley & Sons, Ltd.     

Fabrication of starch blend films with different matrices and their mechanical properties

The objective of the study was to determine the effects of molecular sizes of amylose (AM) and starch granules on the mechanical properties of thermoplastic starch (TPS) blend films. Leached amylose solution from cassava (CS_ AM) and mung bean (MB_AM), and two forms of amylopectin (AP) (granular; g and non-granular; ng) of waxy cassava (WxCS) starch were used. Four types of film matrices were fabricated and all TPS blend films contained same amount of AM and glycerol. Results displayed that molecular weight profiles of starch films and presence of granule remnants significantly controlled the film matrix formation, types of crystal formation, and percent of relative crystallinity (%RC) (p < 0.05). Tensile property of TPS films was controlled by %RC and presence of granule remnants. Percent elongation at break (%E_b) of TPS films increased when the films had a large range of molecular weight distribution (from 5.5 × 10⁷ g/mol to 0.4 × 10⁵ g/mol) and contained a high weight fraction (~58%) of starch molecules with M_w~0.4 × 10⁵ g/mol.     

Investigations of the influence on the phase morphology of PP-EPDM-blends on their mechanical properties

This work covers the dependence of the mechanical properties of polymer blends on their composition and their phase morphology. Blends of EPDM-elastomers and polypropylene were prepared covering the whole concentration range. The phase morphology was varied strongly by employing different mixing techniques and its morphology was characterized by means of electron microscopy and light microscopy, as well as by x-ray scattering and calorimetry.Mechanical properties such as the complex shear modulus, the tensile modulus as well as the stress strain behavior were investigated as a function of the composition of the blends and their phase morphology. The experimental finding is that the complex modulus, the tensile modulus, the yield stress, and the ultimate stress are rather insensitive with respect to the phase morphology and vary continuosly with the composition. The elongation at break, on the other hand, as well as the impact strength were found to depend on the phase morphology and to vary discontinously with the composition. One conclusion to be drawn is that one is not always forced to control the phase morphology tightly during processing in order to obtain materials with sufficiently good mechanical properties. Rather, simple theoretical approaches, neglecting details of the phase morphology are frequently able to satisfactorily predict mechanical properties of multiphase blends.