新型水溶性多色荧光碳点的制备及细胞成像研究

以鸡蛋清和牛奶分别与葡萄糖进行水热反应,制备水溶性多色荧光碳点,通过膜和柱层析分离纯化,利用透射电子显微镜(TEM)、紫外吸收光谱(UV)、荧光光谱(FL)、红外光谱(FTIR)等技术对所制备碳纳米粒子的粒径大小、吸收光谱、发光性质、表面基团进行表征。将所制备的碳点与小鼠黑色素瘤细胞共孵育,进行细胞成像应用评价。结果表明:制备的两种水溶性荧光碳点平均粒径分别为2.5 nm和4.9 nm,可在紫外灯下发出明亮的荧光,紫外最大吸收波长为250 nm。基于鸡蛋清或牛奶与葡萄糖反应制备的多色荧光碳量子点具有良好水溶性,其荧光光谱最大发射波长分别在410 nm和400 nm处,同时在660~800 nm激发波长范围内具有上转换性质,且荧光发射光谱随着激发光波长的增加发生红移。红外光谱表明存在—COOH、—NH2和—OH基团。细胞成像结果表明,在405 nm或488 nm激光照射下,所制备的碳点在细胞内的荧光成像清晰可见,而且在碳点浓度小于2.5 mg/mL时,均表现出较低的细胞毒性。     

青柿子粗提物简易制备荧光碳点及对Fe~(3+)的检测

以青柿子(Diospyros Kaki L. f)提取物作为碳源,通过水热法简易制备荧光碳点,并对其进行表征。结果显示所制备的碳点为类圆球颗粒,平均粒径为15. 39 nm。X射线衍射(XRD)表明该碳点为类石墨烯的无定形碳材料;光电子能谱(XPS)表明其构成元素较复杂,但以碳点为主的元素均有表达,且符合一般碳点材料的元素组成;该碳点表面含有羟基、羧基和氨基等活性基团;在350 nm处有紫外吸收,具有激发波长依赖性特点荧光,最大激发波长为355 nm,最大发射波长为445 nm;在355 nm激发波长下,其光谱发射在p H5. 0～11. 0范围内具有稳定的荧光。该碳点在365 nm紫外光照射下,表现出较强的蓝色荧光,对Fe3+具有较好的特异识别能力,可用于Fe3+的荧光检测。Fe3+浓度在0. 45～50μmol/L范围内与PM-CDs的荧光强度呈线性关系(r2=0. 923 4)。试验在碳点纯化方面存在局限,需进一步探讨生物质材料碳点纯化方式,提高目标分析物的识别位点保有量,获得高效检测目标。     

川木香水热法一步合成荧光碳量子点及光学性能研究

以中药材川木香原药为碳源，采用水热法一步合成了荧光碳量子点。通过水热法实验条件优化，获得制备荧光碳量子点的最佳实验参数，通过透射电镜(TEM)对荧光碳量子点进行形貌表征，通过X射线光电子能谱分仪(XPS)对荧光碳量子点进行元素组成分析，通过荧光光谱和紫外-可见吸收光谱对荧光碳量子点进行了光学性能研究。结果表明：川木香用量1.00 g,水热反应温度180℃,水热反应时间2.0 h时，制备得到的荧光碳量子点光学性能最佳。荧光碳量子点平均粒径为5 nm,主要含有C元素和O元素，最大激发波长为360 nm,对应的发射波长为420 nm,特征吸收峰为280 nm,量子产率为12.9%。     

第二近红外窗口荧光Ag2Te量子点的合成

以巯基辛烷为表面配体, 通过调控Ag前体和Te前体的比例, 制备了第二近红外窗口荧光Ag₂Te量子点. 采用透射电子显微镜(TEM)、 X射线衍射光谱(XRD)、 X射线光电子能谱(XPS)、 紫外-可见-近红外吸收光谱和荧光光谱等对产物进行了表征. 结果表明, 制得了粒径均一、 分散性好的油溶性Ag₂Te量子点, 其最大荧光发射波长位于1320 nm, 荧光量子产率高达4.2%.     

葡萄糖酸碳量子点的合成及其光学性能的研究

以葡萄糖酸为碳源,采用微波法、热解法和水热溶液法合成了水溶性较好的蓝色荧光碳量子点。用透射电镜(TEM)观察其形貌,荧光光谱(FL)和紫外可见光谱(UV)探究其激发和发射光谱,用时间分辨光谱(TRF)测其荧光寿命值。微波和热解法制备的碳量子点粒径在2.5~7.5 nm之间,激发波长为360 nm,发射波长为450 nm,荧光发射依赖激发波长,有三个荧光寿命,表面状态不均一。水热法制备的碳量子点,粒径在3.0~8.5 nm之间,激发波长为350 nm,发射波长为430 nm,荧光发射不依赖激发波长,只有一个荧光寿命值,表面状态均一。水热法合成的碳量子点荧光量子产率高为6.01%,为进一步研究葡萄糖酸制备碳量子点提供参考。     

氮掺杂鸡毛碳点荧光关开探针用于测定百草枯

以鸡毛和乙二胺为碳源和氮源,通过一步水热法合成强荧光性能的氮掺杂碳量子点(N-CQDs),并优化其制备和掺杂条件.该碳量子点具有良好的光学、结构性质和稳定性,平均粒径7.89 nm,荧光量子产率为14％.最大激发波长为320 nm,最大发射波长为386 nm.Hg2+存在条件下N-CQDs溶液的荧光被碎灭(关),添加百...     

荧光可调控的碳量子点的电化学制备及性质研究

采用循环伏安法（Cyclic Voltammetry,CV）在碱性条件下电解石墨棒,得到水溶性的荧光碳量子点. 通过透射电子显微镜（TEM）、拉曼光谱（Raman spectrum）、原子力显微镜（AFM）对所制备的碳量子点进行形貌及结构表征,发现该碳量子点由1～4层石墨烯片层堆积形成,粒径在19 nm左右,厚度在1 nm左右. 通过荧光光谱（PL）、紫外可见吸收光谱（UV-vis）、傅里叶变换红外光谱（FTIR）、X射线光电子能谱（XPS）对所制备的碳量子点进行性质测定,发现该碳量子点在400和525 nm处有两个荧光发射峰,且通过控制扫描周数可以调节两个发射峰的相对强度,从而调控碳量子点的荧光颜色：随着扫描周数的增加,400 nm处发射峰的相对强度逐渐减小,而525 nm处发射峰的相对强度逐渐增大,两个荧光发射峰分别与碳量子点的π-π共轭体系和含氧官能团的n-π共轭体系有关.     

碳量子点荧光探针的制备及其在苦味酸检测中的应用

以银杏叶为原料,采用水热法制备得到新型荧光碳量子点(CQDs)。该碳量子点的平均粒径为5.5 nm,最大激发波长为335 nm,最大发射波长为418 nm。基于碳量子点荧光光谱与苦味酸(PA)吸收光谱存在部分重叠而发生荧光共振能量转移(FRET),建立了以碳量子点作为荧光探针用于苦味酸检测的新方法。在最佳实验条件下,加入苦味酸前、后的荧光强度比值(I₀/I)与苦味酸浓度(c)在0.2～800μmol/L范围内呈良好的线性关系,相关系数(r)为0.999 5,检出限(LOD)为32 nmol/L。在5、40、80μmol/L加标水平下,实际水样中苦味酸的回收率为98.0%～104%,相对标准偏差(RSD)为1.0%～3.2%。该方法可用于实际样品中苦味酸的灵敏、快速和高效检测。     

一步水热法制备氮掺杂碳点用于Fe3+检测及细胞成像

以生物相容性优异的人体必需氨基酸分子色氨酸和苏氨酸为前驱体,通过一步水热法合成了水溶性良好的蓝色荧光氮掺杂碳点(N-CDs).采用高分辨率透射电镜、X射线衍射光谱、X射线光电子能谱、傅里叶红外吸收光谱、紫外可见吸收光谱、荧光光谱对其结构、组成和光学性质进行研究.结果表明所制备的N-CDs尺寸均一,平均粒径为4.1 nm...     

枫树叶荧光碳量子点的合成及其传感性能研究

以枫树叶为原料,硼氢化钠为还原剂,利用水热法合成了一种新型的荧光碳量子点CQDs-fsy。利用XRD,TEM和FT-IR对碳量子点的结构进行了表征,利用紫外和荧光光谱仪研究了该碳量子点的光学性质,该荧光碳点的荧光量子产率为5.60%,最大激发波长为348nm,最大发射波长为428 nm。该碳点具有规则的球形分散结构;平均粒径为5~10 nm;表面富含羧基,氨基和羟基官能团;该碳点在水溶液中对Hg~(2+)具有专一识别能力,线性范围为5.00×10~(-7)~1.55×10~(-5)mol/L,线性方程为y=-10.37 x+337.24,R~2=0.996,检出限为2.01×10~(-8)mol/L。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.