加速溶剂萃取-凝胶色谱净化-气质联用测定土壤中15种有机氯农药残留的方法研究

建立了加速溶剂萃取-凝胶色谱净化-气质联用同时测定土壤中15种有机氯农药的分析方法。优化了凝胶色谱(GPC)净化的条件,比较了凝胶色谱净化及浓硫酸净化法对15种有机氯回收率的影响。结果表明,采用GPC净化能够有效避免浓硫酸净化对氯丹、异狄氏剂、硫丹、甲氧滴滴涕等农药回收率的影响,GPC净化的最佳收集时间为10~15 min,15种有机氯农药的回收率为56%~122%。15种有机氯农药在0.03~6.0 mg/L范围内具有较好的线性,相关系数达0.999以上,方法的检出限为0.1~5.0μg/kg,定量下限为0.4~16.0μg/kg。采用该方法对实际样品进行加标回收率实验,土壤样品的加标回收率为68%~122%,相对标准偏差为1.2%~5.9%。该方法简单、快捷、灵敏度高,已用于实际土壤样品的检测。     

QuEChERS-凝胶渗透色谱/气相色谱-质谱法同时测定降尘中18种有机氯农药

建立了在线凝胶渗透色谱/气相色谱-质谱(GPC/GC-MS)测定大气降尘中18种有机氯农药残留的分析方法。样品经过简化QuEChERS方法处理后,经乙腈萃取,石墨化炭黑(GCB)净化,一步离心后过膜上机检测。采用该方法能在30 min内处理8~10个样品,配合GPC净化,不仅缩短了分析时间,而且提高了工作效率和结果的准确性。检测结果表明,18种有机氯农药在0.025~2.0 mg/L质量浓度范围内线性关系良好,相关系数为0.991 9~0.999 6,样品检出限为3.2~14.6μg/kg,定量下限为10.7~48.7μg/kg。在0.2、1.0 mg/kg 2个加标水平下,18种有机氯农药的平均回收率为78.6%~117.3%,相对标准偏差(RSD,n=5)为1.3%~5.1%。     

凝胶渗透色谱-固相萃取净化/气相色谱-串联质谱法测定动物性食品中167种农药残留

建立了肉类、水产类等动物性食品中167种农药残留的气相色谱-串联质谱检测方法。样品匀浆后,采用乙腈提取,以凝胶渗透色谱和Carb-NH2萃取柱联合净化,气相色谱-串联质谱检测,外标法定量。167种农药的响应在1~200μg/L质量浓度范围内线性良好,相关系数在0.994以上,各农药的检出限为0.3~3μg/kg,定量下限为1~10μg/kg。以猪肉样品作为代表性基质,进行0.01,0.04 mg/kg 2个水平的加标回收实验,回收率为66.4%~111.5%,相对标准偏差为1.3%~17.8%。本方法准确可靠,灵敏度高,样品净化效果好,能够满足动物性食品中农药多残留的痕量分析要求。     

茶叶中25种有机氯农药多残留气相色谱测定方法

利用气相色谱(GC)建立了茶叶中25种有机氯农药同时测定的方法。茶叶中有机氯农药残留通过正己烷-丙酮(体积比2∶1)溶液提取,浓缩后过弗罗里硅土柱净化,采用正己烷-乙酸乙酯(体积比9∶1)溶液淋洗,淋洗液吹氮至干后以正己烷定容供GC测定。标准工作曲线范围在0.005~0.500mg/L之间。在茶叶样品中0.005~0.100mg/kg水平有机氯混标加标回收率在71%~110%之间,相对标准偏差在4.6%~13.7%之间。除乙酯杀螨醇定量下限为8.0μg/kg以外,其余24种有机氯农药定量下限均为5.0μg/kg。     

悬浮固化-分散液液微萃取-气相色谱法测定野木瓜中9种有机氯农药残留量

建立了悬浮固化-分散液液微萃取-气相色谱法测定野木瓜中9种有机氯农药残留量的方法。样品经石油醚提取、浓硫酸净化、悬浮固化-分散液液微萃取法浓缩后,用气相色谱-电子捕获检测器(GC-ECD)检测,外标法定量。结果表明,9种农药含量在1~100μg/L范围内线性关系良好,相关系数R2在0.99以上,方法检出限(S/N=3)为0.01~0.07μg/kg。9种有机氯农药在1.75,7.00,28.0μg/kg 3个水平添加下,平均回收率范围为83.3%~116.7%,相对标准偏差(RSD)范围为1.5%~14%,方法已用于野木瓜中9种有机氯农药残留的测定。     

气相色谱-负化学电离源-飞行时间质谱测定烟草中有机氯农药残留

采用QuEChERS前处理方法,建立了气相色谱-负化学电离源-飞行时间质谱(GC-NCI-TOF-MS)检测烟草中10种有机氯农药残留的分析方法。样品采用乙酸乙酯-正己烷(1 : 1, v/v)溶液提取,提取液经N-丙基乙二胺(PSA)、无水硫酸镁分散固相萃取净化,用GC-NCI-TOF-MS检测分析。根据有机氯化合物特征离子的精确质量数、同位素离子峰簇、碎片离子丰度比和保留时间对目标物定性鉴定,外标法定量。10种有机氯农药的线性关系良好,相关系数 (r²)均大于0.997;相对标准偏差小于6.5%;检出限为0.04~0.80 μ g/kg;加标回收率为77.2%~93.0%。该方法简单快速、灵敏度高、准确性好,适用于烟草中有机氯农药残留的定性分析和定量检测。     

盐析辅助液液萃取交联聚维酮净化-靶向单一离子监测/高分辨质谱法测定蜂蜜中新烟碱类农药残留

基于盐析辅助液液萃取(LLE)交联聚维酮(PVPP)净化技术,建立了蜂蜜中7种新烟碱类农药的靶向单一离子监测(TSIM)/高分辨质谱检测方法。样品用乙腈基于盐析辅助LLE-PVPP提取净化,采用BEH C18色谱柱为分析柱,甲醇-水体系(两相均含0.1%甲酸和5 mmol/L甲酸铵)作为流动相,梯度洗脱,采用高分辨质谱TSIM模式检测目标化合物,内标法定量。结果表明,盐析辅助LLE-PVPP净化技术可实现提取净化一步式样品制备,TSIM扫描模式则显示了更宽的线性动态范围和更高的灵敏度与准确度。7种新烟碱类农药在0.01~100μg/L或0.02~100μg/L范围内具有良好的线性关系(r20.999);方法检出限为0.03~0.07μg/kg,定量下限为0.1~0.2μg/kg。在0.2、2、20μg/kg 3种加标水平下,7种新烟碱类农药在蜂蜜中的平均回收率为84.8%~112.7%,日内精密度(RSDr)为0.9%~5.7%,日间精密度(RSDR)为3.7%~9.7%。该方法前处理简单快速、成本较低,灵敏度高、重现性好,可广泛应用于蜂蜜中新烟碱类农药残留的快速检测。     

气相色谱法测定虾中有机氯农药和多氯联苯残留量

建立了气相色谱法检测虾中12种有机氯农药(OCPs)和7种多氯联苯(PCBs)残留的方法。捣碎匀浆后的样品采用正己烷/二氯甲烷提取,H2SO4(浓)净化,气相色谱仪电子捕获检测器进行分析测定。有机氯农药和多氯联苯的定量限为0.3~1.5μg/kg;在虾中2,10,20μg/kg添加水平的平均回收率为70.6%~102%,相对标准偏差为2.4%~6.2%。方法适用于虾中有机氯农药和多氯联苯的定性定量分析。     

凝胶渗透色谱-固相萃取联合净化气相色谱-质谱联用法测定动物性食品中30种有机氯农药的残留量

建立了猪肉、鸡肉、鱼肉和虾肉等动物性食品中30种有机氯农药残留的气相色谱-质谱联用检测方法。样品匀浆后,采用乙腈提取,以凝胶渗透色谱和弗罗里硅土固相萃取柱联合进行净化,气相色谱-质谱检测,以同位素内标法定量。30种有机氯农药的响应在5.0~500.0 μg/L范围内呈良好的线性,相关系数在0.996以上,各有机氯农药的检出限在0.2~2.7 μg/kg之间。以猪肉、鸡肉、鱼肉和虾肉作为代表性基质,进行5.0、10.0、20.0 μg/kg 3个水平的加标回收试验,回收率在55.0%~119.1%之间,相对标准偏差在0.4%~15.0%之间。该方法准确可靠,灵敏度高,样品净化效果好,能够满足动物性食品中有机氯农药多残留痕量分析的要求。     

全自动凝胶净化-浓缩-固相萃取/气相色谱-质谱法测定紫皮石斛中有机磷农药残留

建立了以凝胶渗透色谱(GPC)和固相萃取(SPE)净化、气相色谱-质谱(GC-MS)法同时测定紫皮石斛中10种有机磷农药残留的方法。样品用乙腈超声提取,提取液经GPC去除类脂杂质和大分子物质,后经Envi-Carb/NH2固相萃取柱净化,选择离子(SIM)监测模式检测,外标法定量。在26min内10种农药得到很好的分离,农药残留量在0.02~0.5μg/mL,方法的线性良好,相关系数为0.997 3~0.999 9,农药加标浓度为0.05mg/kg和0.2mg/kg时,加标回收率在70.4%~115.8%,相对标准偏差在2.8%~9.6%,满足国家标准要求,检出限为0.005 2~0.011mg/kg。方法简便、快速、灵敏、准确,能够运用于石斛中多组分有机磷农药残留的定性和定量分析。     

Gels from a semifluorinated n-alkane in fluorinated solvents as a probe for intermolecular interactions

Diblock semifluorinated n-alkanes can form aggregates and gels in fluorinated solvents. We have investigated the thermal behavior of binary mixtures comprising F(CF₂)₈(CH₂)₁₆H and fluorinated solvents. The solvents were perfluorohexane, perfluoroheptane, perfluorooctane, perfluorooctyl bromide, perfluorodecalin, and perfluorotributylamine. The phase diagrams were used to calculate the activity coefficients of the two components and the main excess thermodynamic functions. The solubility and self-assembly behavior of F₈H₁₆ in the fluorinated solvents are related to the different solute–solvent dispersion interactions that depend on the polarizabilities and ionization potentials of the interacting species, and on the structural properties of the solvent.     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

Studies on the Formation of Catalytically Active PGM Nanoparticles from Model Solutions as a Basis for the Recycling of Spent Catalysts

The paper presents basic studies on the precipitation of platinum, palladium, rhodium, and ruthenium nanoparticles from model acidic solutions using sodium borohydride, ascorbic acid, and sodium formate as reducing agents and polyvinylpyrrolidone as a stabilizing agent. The size of the obtained PGM particles after precipitation with NaBH₄ solution does not exceed 55 nm. NaBH₄ is an efficient reducer; the precipitation yields for Pt, Pd, Ru, Rh are 75, 90, 65 and 85%, respectively. By precipitation with ascorbic acid, it is possible to efficiently separate Pt, Rh, and Ru from Pd from the two-component mixtures. The obtained Pt, Pd, and Rh precipitates have the catalytic ability of the catalytic reaction of p-nitrophenol to p-aminophenol. The morphological characteristic of the PGM precipitates was analyzed by AFM, SEM-EDS, and TEM.     

HCOO在Cu(110)、Ag(110)和Au(110)表面的吸附

采用密度泛函理论(DFT)以及广义梯度近似方法(GGA)计算了甲酸根(HCOO)在Cu(110)、Ag(110)和Au(110)表面的吸附. 计算结果表明, 短桥位是最稳定的吸附位置, 计算的几何参数与以前的实验和计算结果吻合. 吸附热顺序为Cu(110)(-116 kJ·mol-1)>Ag(110)(-57 kJ·mol-1)>Au(110)(-27 kJ·mol-1), 与实验上甲酸根的分解温度相一致. 电子态密度分析表明, 吸附热顺序可以用吸附分子与金属d-带之间的Pauli 排斥来关联, 即排斥作用越大, 吸附越弱. 另外还从计算的吸附热数据以及实验上HCOO的分解温度估算了反应CO2+1/2H2→HCOO的活化能, 其大小顺序为Au(110)>Ag(110)>Cu(110).     

Transition metal complexes of the tripodal ligand 4-(2′-pyridylmethyl)-4-azaheptane-1,7-diamine. Crystal structures of [CuLCl]ClO4 and [NiL(MeCN)2](ClO4)2

The tripodal ligand 4-(2′-pyridylmthyl)-4-azaheptane-1,7-diamine has been prepared by reaction of 2-aminemethyl pyridine with acrylonitrile, followed by the reduction of the nitrile groups. Copper(II), nickel(II), zinc(II), cobalt(III) and chromium(III) complexes of the ligand have been prepared and characterized and the crystal structures of the complexes [CuLCl]ClO₄ and [NiL(MeCN)₂](ClO₄)₂ determined. The copper complex is five coordinate with approximate square pyramidal stereochemistry with the apical position occupied by a primary amine donor. The nickel complex is octahedral with the pyridine nitrogen donor lying trans to an acetonitrile ligand.     

Direct Quantitation of Phytocannabinoids by One-Dimensional 1H qNMR and Two-Dimensional 1H-1H COSY qNMR in Complex Natural Mixtures

The widespread use of phytocannabinoids or cannabis extracts as ingredients in numerous types of products, in combination with the legal restrictions on THC content, has created a need for the development of new, rapid, and universal analytical methods for their quantitation that ideally could be applied without separation and standards. Based on previously described qNMR studies, we developed an expanded ¹H qNMR method and a novel 2D-COSY qNMR method for the rapid quantitation of ten major phytocannabinoids in cannabis plant extracts and cannabis-based products. The ¹H qNMR method was successfully developed for the quantitation of cannabidiol (CBD), cannabidiolic acid (CBDA), cannabinol (CBN), cannabichromene (CBC), cannabichromenic acid (CBCA), cannabigerol (CBG), cannabigerolic acid (CBGA), Δ9-tetrahydrocannabinol (Δ9-THC), Δ9-tetrahydrocannabinolic acid (Δ9-THCA), Δ8-tetrahydrocannabinol (Δ8-THC), cannabielsoin (CBE), and cannabidivarin (CBDV). Moreover, cannabidivarinic acid (CBDVA) and Δ9-tetrahydrocannabivarinic acid (Δ9-THCVA) can be distinguished from CBDA and Δ9-THCA respectively, while cannabigerovarin (CBGV) and Δ8-tetrahydrocannabivarin (Δ8-THCV) present the same ¹H-spectra as CBG and Δ8-THC, respectively. The COSY qNMR method was applied for the quantitation of CBD, CBDA, CBN, CBG/CBGA, and THC/THCA. The two methods were applied for the analysis of hemp plants; cannabis extracts; edible cannabis medium-chain triglycerides (MCT); and hemp seed oils and cosmetic products with cannabinoids. The ¹H-NMR method does not require the use of reference compounds, and it requires only a short time for analysis. However, complex extracts in ¹H-NMR may have a lot of signals, and quantitation with this method is often hampered by peak overlap, with 2D NMR providing a solution to this obstacle. The most important advantage of the COSY NMR quantitation method was the determination of the legality of cannabis plants, extracts, and edible oils based on their THC/THCA content, particularly in the cases of some samples for which the determination of THC/THCA content by ¹H qNMR was not feasible.     

SYNTHESIS AND CHARACTERIZATION OF METAL COMPLEXES WITH AMPICILLIN

Abstract

The reaction, in water, of Co(II), Ni(II), Cu(II), Zn(II) and Cd(II) ions with sodium ampicillinate at room temperature has allowed isolation of dimers with the following general formula [M(amp)Cl]₂ × nH₂O (n = 1.5?3.2). The complexes were characterized by elemental analyses, conductivity measurements, magnetic susceptibilities and spectroscopic methods (IR, Raman, EPR and UV-Visible). A dinuclear structure based on octahedrally coordinated metal ions is proposed.     

Magnetism of metal-nitroxide compounds involving bis-chelating imidazole and benzimidazole substituted nitronyl nitroxide free radicals

Coordination compounds based on imidazole and benzimidazole substituted nitronyl nitroxide radicals with transition metal ions and trivalent lanthanide ions are described from the perspective of their magnetic properties.For the transition metal compounds the crystal structures show various metal-nitroxide dimensionalities including mononuclear (0D), one-dimensional (1D) and two-dimensional (2D) complexes. The mononuclear complexes were isolated with most metal ions of the first transition series. One copper(II) complex shows a copper(II)-radical ferromagnetic coupling (J = +75 cm⁻¹) while for the other mononuclear compounds, mainly with manganese(II), the metal-radical interactions are antiferromagnetic. The one-dimensional and two-dimensional complexes are manganese(II) compounds which show canting effects leading to weak ferromagnetism.For the trivalent lanthanide ions [La(III), Gd(III) and Eu(III)], three series of mononuclear complexes were obtained in which the metal center is bound to four, two or one nitroxide radicals depending on the counter ions and ancillary ligands. Unexpectedly, in most gadolinium(III) complexes, the Gd(III)-radical interactions were found to be antiferromagnetic in contradiction with other foundings and previous theoretical models. In support to the magnetic studies, the optical properties of the lantanide complexes have also been investigated and are briefly described.     

具有聚集诱导发光性质的近红外荧光染料

聚集诱导发光(AIE)现象的发现为解决传统有机荧光分子在高浓度和聚集形态下存在的荧光猝灭问题提供了最佳方案,并实现了在光电器件、化学传感、生物成像和靶向治疗等众多领域的广泛应用.随着对AIE 发光机理研究的不断深入,AIE 分子体系得到了极大的扩展.其中,一类具有给体-受体结构的AIE分子能够显著降低分子能隙,使发光分...     

Simple,Selective, and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel（Ⅱ）, Copper （Ⅱ）, Cobalt （Ⅱ）, and Iron （Ⅲ） with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.