螺旋型薄膜介质平板Blumlein线实验

为实现脉冲功率源小型化,设计了一种螺旋形薄膜介质Blumlein线,应用火花隙开关对其进行了放电实验研究,并对负载电压波形进行了分析。结果表明,开关电感会减缓脉冲前沿,电极直流阻抗使得负载输出电压效率显著降低,波形平顶趋于减小,分布电容耦合造成负载电压的预脉冲,而均压层不会影响传输特性,不会对负载电压波形造成影响。     

XH-1装置电感储能系统的电路模拟

 针对XH-1装置电感储能系统,建立了电爆炸断路开关基于开关电阻倍增比与比能关系的电路模型,给出了与电感储能系统耦合时,利用PSPICE模拟计算得到的开关上的电流电压波形和负载上的电压波形,分析了负载阻抗参数对输出脉冲的影响。     

XH-1装置电感储能系统的电路模拟

针对XH-1装置电感储能系统,建立了电爆炸断路开关基于开关电阻倍增比与比能关系的电路模型,给出了与电感储能系统耦合时,利用PSPICE模拟计算得到的开关上的电流电压波形和负载上的电压波形,分析了负载阻抗参数对输出脉冲的影响。     

便携式脉冲形成线设计与实验研究

采用聚酯薄膜为绝缘材料,设计了一种小型化便携式层绕Blumlein线,其主要特点是采用S型层绕的方法对薄膜介质平板Blumlein线进行绕制,使形成线的体积小,结构紧凑,有利于脉冲功率源小型化、实用化的发展。其集成了薄膜电容器易卷绕、耐高压、储能强的优势,同时具备了传输线的特点。采用气体火花间隙开关,对S型薄膜介质脉冲形成线的耐压特性及负载输出波形进行了实验研究。结果表明:开关的导通特性对脉冲形成线的负载输出波形有很大的影响,开关电感及开关抖动等因素会影响脉冲波形的前后沿,使输出脉冲方波波形质量变差。采用PSpice软件对实验等效电路进行了模拟,得到了与实验一致的结果。设计的Blumlein线体积为50 cm18 cm12 cm,承载电压50 kV,负载输出脉冲上升沿50 ns,平顶宽度120 ns。     

便携式脉冲形成线设计与实验研究

采用聚酯薄膜为绝缘材料,设计了一种小型化便携式层绕Blumlein线,其主要特点是采用S型层绕的方法对薄膜介质平板Blumlein线进行绕制,使形成线的体积小,结构紧凑,有利于脉冲功率源小型化、实用化的发展。其集成了薄膜电容器易卷绕、耐高压、储能强的优势,同时具备了传输线的特点。采用气体火花间隙开关,对S型薄膜介质脉冲形成线的耐压特性及负载输出波形进行了实验研究。结果表明：开关的导通特性对脉冲形成线的负载输出波形有很大的影响,开关电感及开关抖动等因素会影响脉冲波形的前后沿,使输出脉冲方波波形质量变差。采用PSpice软件对实验等效电路进行了模拟,得到了与实验一致的结果。设计的Blumlein线体积为50 cm18 cm12 cm,承载电压50 kV,负载输出脉冲上升沿50 ns,平顶宽度120 ns。     

S波段锥形磁绝缘线振荡器长脉冲实验研究

对一种由弱变和强变结构组成的锥形磁绝缘线振荡器进行了长脉冲实验研究。在二极管电压350 kV左右、电流约25 kA、脉宽约128 ns的条件下,获得了500 MW、脉宽约90 ns的高功率微波输出。对波形中出现的拐点进行了分析,研究表明：二极管电压波形好坏会对微波源的性能造成严重的影响,较好的电压波形是实现长脉冲运行的关键。同时对采用不锈钢平面负载、不锈钢丝网状负载以及石墨负载电子收集极进行了实验研究,研究表明采用石墨收集极可以输出较好的微波波形。     

S波段锥形磁绝缘线振荡器长脉冲实验研究

 对一种由弱变和强变结构组成的锥形磁绝缘线振荡器进行了长脉冲实验研究。在二极管电压350 kV左右、电流约25 kA、脉宽约128 ns的条件下,获得了500 MW、脉宽约90 ns的高功率微波输出。对波形中出现的拐点进行了分析,研究表明：二极管电压波形好坏会对微波源的性能造成严重的影响,较好的电压波形是实现长脉冲运行的关键。同时对采用不锈钢平面负载、不锈钢丝网状负载以及石墨负载电子收集极进行了实验研究,研究表明采用石墨收集极可以输出较好的微波波形。     

薄膜介质层绕式Blumlein线理论与实验研究

对薄膜介质层绕式Blumlein线的特性参数进行了理论分析。采用Pspice软件对电路模型进行了计算,分析了开关电感、寄生电阻对负载输出波形的影响。结果表明:开关电感的存在使得负载波形前沿变缓,后延波形扭曲变差,寄生电阻会影响负载的电压输出效率。采用模拟软件对传输线中的电磁场分布进行了计算,结果表明薄电极边缘场畸变以及折叠弯曲部分的场变化是绝缘介质耐压必须考虑的因素。基于此理论分析,设计制作了一种新型薄膜介质Blumlein线,绝缘材料为聚酯薄膜,单层薄膜厚100 μm,电极为厚50 μm的铜皮,单元模块设计耐压50 kV。进行了三级模块串联叠加实验,充电25 kV,匹配负载输出60 kV,脉冲上升沿80 ns,脉冲宽度200 ns。     

薄膜介质层绕式Blumlein线理论与实验研究

对薄膜介质层绕式Blumlein线的特性参数进行了理论分析。采用Pspice软件对电路模型进行了计算,分析了开关电感、寄生电阻对负载输出波形的影响。结果表明:开关电感的存在使得负载波形前沿变缓,后延波形扭曲变差,寄生电阻会影响负载的电压输出效率。采用模拟软件对传输线中的电磁场分布进行了计算,结果表明薄电极边缘场畸变以及折叠弯曲部分的场变化是绝缘介质耐压必须考虑的因素。基于此理论分析,设计制作了一种新型薄膜介质Blumlein线,绝缘材料为聚酯薄膜,单层薄膜厚100μm,电极为厚50μm的铜皮,单元模块设计耐压50 kV。进行了三级模块串联叠加实验,充电25 kV,匹配负载输出60 kV,脉冲上升沿80 ns,脉冲宽度200 ns。     

螺旋线型脉冲形成线匝间击穿与输出波形的研究

 针对螺旋线型脉冲形成线放电过程的匝间击穿问题,采用数值模拟的方法研究了影响螺旋线上轴向电场的因素,模拟结果表明：螺旋线的螺旋角越大、开关的上升沿越小、负载的阻值越小则越容易造成匝间击穿;针对输出波形的前沿上冲和下凹问题,通过数值模拟和实验方法研究了加速器内阻抗不匹配段对输出波形的影响,结果表明: 改变螺旋线与开关之间连接段的阻抗以及开关和二极管之间过渡段的阻抗,使之接近于螺旋线阻抗,并使电长度减小,可以消除波形的前沿上冲和下凹,得到近似方波的高电压脉冲输出。     

真空热处理碳纳米管的储氢性能研究

研究了真空热处理对多壁碳纳米管(MWNTs)电化学储氢性能的影响.采用化学气相沉积法(CVD)制备碳纳米管，碳纳米管与LaNi₅储氢合金按质量比1∶10混合，制作成CNTs-LaNi₅电极.电解池采用三电极体系，6mol/L KOH为电解液，Ni(OH)₂为正极，Hg/HgO为参比电极.实验结果表明，在相同的充放电条件下，850℃时CNTs-LaNi₅电极的储氢性能最好，克容量最大为503.6mAh/g，相应的平台电压高达1.18V.从500—850℃随着温度升高，放电量有较大幅度的增加，但到950℃时放电量反而下降.由此可见，碳纳米管的热处理温度对碳纳米管的电化学储氢性能有着较大的影响. 关键词： 碳纳米管(CNTs) 储氢性能 5合金')" href="#">LaNi₅合金 化学气相沉积法(CVD法)     

Current-voltage characteristics of diodes based on a four-component chalcogenide glass

An experimental study was made of film diodes based on a chalcogenide glass with symmetric and asymmetric electrodes and with two lower symmetric electrodes. Film diodes with aluminum electrodes can be used as varistors. The electrodes affect the shape of the current-voltage characteristics. Diodes having two lower electrodes have a longer useful lifetime than do those having an upper electrode and a lower one. Generation in the negative-resistance region is described.Translated from Izvestiya VUZ. Fizika, No. 12, pp. 30–33, December, 1969.The author thanks P. T. Oreshkin for constant interest in this study.     

Electrochemical, morphological and microstructural characterization of carbon film resistor electrodes for application in electrochemical sensors

The electrochemical and microstructural properties of carbon film electrodes made from carbon film electrical resistors of 1.5, 15, 140 Ω and 2.0 kΩ nominal resistance have been investigated before and after electrochemical pre-treatment at +0.9 V vs SCE, in order to assess the potential use of these carbon film electrodes as electrochemical sensors and as substrates for sensors and biosensors. The results obtained are compared with those at electrodes made from previously investigated 2 Ω carbon film resistors. Cyclic voltammetry was performed in acetate buffer and phosphate buffer saline electrolytes and the kinetic parameters of the model redox system Fe(CN)₆^3−/4− obtained. The 1.5 Ω resistor electrodes show the best properties for sensor development with wide potential windows, similar electrochemical behaviour to those of 2 Ω and close-to-reversible kinetic parameters after electrochemical pre-treatment. The 15 and 140 Ω resistor electrodes show wide potential windows although with slower kinetics, whereas the 2.0 kΩ resistor electrodes show poor cyclic voltammetric profiles even after pre-treatment. Electrochemical impedance spectroscopy related these findings to the interfacial properties of the electrodes. Microstructural and morphological studies were carried out using contact mode Atomic Force Microscopy (AFM), Confocal Raman spectroscopy and X-ray diffraction. AFM showed more homogeneity of the films with lower nominal resistances, related to better electrochemical characteristics. X-ray diffraction and Confocal Raman spectroscopy indicate the existence of a graphitic structure in the carbon films.     

Semicylindrical acoustic transducer from a dielectric elastomer film with compliant electrodes

A semicylindrical acoustic transducer was constructed using a dielectric elastomer film with compliant electrodes that is an electroactive polymer composed of a polyurethane elastomer base and polyethylene dioxythiophene/polystyrene sulfonate electrodes. The use of this dielectric elastomer is advantageous because polyurethane is a common material that keeps its shape without any rigid frame. Because the dielectric elastomer films are essentially incompressible, electric-field-induced thickness changes are usually translated into much larger changes of the film area and side length. Here it is proposed that this change in side length can be utilized for sound generation when the film is bent into a semicylindrical shape. Accordingly, a semicylindrical acoustic transducer was fabricated using a film of thickness of 300 μm and its acoustic characteristics were investigated. The transducer can be operated at low applied voltages by reducing the film thickness, as long as the film is thick enough to generate sufficient force to overcome sound radiation impedance. The second harmonic distortion of the transducer was also investigated as a function of the ratio of the direct current bias voltage to the alternating current audio signal amplitude.     

电极构形对形成大面积放电均匀性影响

设计并制作了空心阴极、钮扣阴极、针阴极和条形阴极,利用CCD照相,在5cm×5cm口径范围内,分别对四种阴极放电的空间均匀性进行了研究。实验表明,在预电离电压800V,主放电电压3kV和气体气压约30Pa的条件下,利用空心阴极放电,能够获得空间较为均匀的放电等离子体。放电等离子体可以用作普克尔盒电光开关的等离子体电极。     

Multislot microwave transmission lines fabricated on an insulating substrate covered with a ferroelectric film

A rigorous electrodynamic model is used to calculate the dispersion characteristics of multislot microwave transmission lines fabricated on a layered structure containing a ferroelectric film. The attenuation due to the finite conductivity of the metal electrodes is found.     

电极构形对形成大面积放电均匀性影响

 设计并制作了空心阴极、钮扣阴极、针阴极和条形阴极，利用CCD照相，在5cm×5cm口径范围内，分别对四种阴极放电的空间均匀性进行了研究。实验表明，在预电离电压800V，主放电电压3kV和气体气压约30Pa的条件下，利用空心阴极放电，能够获得空间较为均匀的放电等离子体。放电等离子体可以用作普克尔盒电光开关的等离子体电极。     

传输式大功率电火花震源在浅水中及井中的压力波形及频谱分析

本文通过对传输式电火花震源在浅水中及井中所产生压力波形的分析,确定了压力波峰值与放电电极距离的关系,获得了压力波与放电能量、静水压、测量距离 之间的基本关系。并对试验结果进行了分析。     

MSM结构ZnO/Cu薄膜的接触特性

利用脉冲激光沉积(PLD)法在Si(111)衬底上分别生长了ZnO薄膜和Cu薄膜, 用Cu薄膜作电极,研究了ZnO薄膜与Cu薄膜的接触特性。分别用X射线衍射仪、扫描电子显微镜和I-V测试的方法对样品的晶体质量、结构和电学性质进行了测试。结果表明:样品中ZnO薄膜和Cu薄膜均具有高度的择优取向;当Cu和 ZnO直接接触时,样品的I-V特性是非线性的;当Cu和 ZnO之间通过ZnO:Cu层间接接触时形成良好的欧姆接触,而且退火后欧姆接触性能明显提高,电阻率降低约2/3。本研究为价格低廉的Cu电极成为ZnO基器件的欧姆电极提供了一定的依据。