流动注射分析中试样分散的对流—扩散理论

用两种方法求解适合于单一平直管道且无化学反应的流动注射分析（ＦＩＡ）体系的对流－扩散方程，得到了述塞状进样在管道中分散后的浓度分布公式，从而得到Ｆ曲线，讨论了反应管和采样管的内径和长度、流速和扩散系数对峰形和分散度的影响；采用数值法解出半峰宽和扩散系数的关系，提出了两种测定扩散系数的方法，为ＦＩＡ体系的设计和指示物质、操作条件的选择提供了理论依据。     

平头pH电极-流动注射联用技术快速滴定食醋中醋酸的方法研究

采用一种具有平头结构的pH电极作为流动注射分析(FIA)的检测器,构建了流动注射自动化酸度滴定系统.优化了样品进样量、流速、载液浓度和反应管长度等参数.用NaOH溶液作为载液,在4.639×10-4～0.212 mol·L-1范围内醋酸浓度的对数与FIA峰的峰面积成正比,该方法的相对标准偏差(RSD)小于0.5%.采用...     

原子光谱分析中的流动注射法

流动注射(FIA)法作为分析操作中一种新的溶液处理技术在近十年来得到十分迅速的发展。FIA法的应用使化学分析实验室中的很多传统设备与操作技术发生了重大的变革,从而受到国际分析化学界广泛的重视。近几年来该法越来越多地用于原子光谱分析,其效果十分引人注目。 (一)FIA采样法用于火焰原子吸收(FAAS)及电感耦合等离子体光谱(ICP)的FIA采样装置多数如图1所示,为单线系统。一定体积的试样通过注入口(阀或针筒)被注入流向雾化器的载流中,几秒钟后得一瞬变峰形信号。由于流速,管道长度及注样方式固定,试样于进入雾化器时在载流中的分散程度能很好地加以控制,因此虽然试样溶液在流动的过程中部分被稀释,同时由于注样的体积一般只有数十μl而无足够的时间达到输出     

希土元素的流动注射分析法检出与测定

本文介绍了简便的、以反应光度法为检测器的流动注射分析法装置。讨论了FIA中试样带的分散及其影响因素。论述了注样体积、载流及显色液流量等操作条件对FIA输出信号的影响。研究了若于显色体系的反应速度曲线并讨论了显色速度对FIA测定的影响。系统地研究五种显色体系FIA测定希土元素的条件及灵敏度。首次使用对乙酰基偶氮胂等体系于FIA测定希土元素。本文还介绍了将FIA用于自动检测萃取色层柱淋洗曲线。     

新型FIA光度法测定铝合金中的铜

研制出了一种新的流动比色装置(FIA),不需要增加任何辅助设备,一次进样同时可连续获得两峰一谷3个吸光度值,均可以用于定量分析.利用吸光度加和技术,使分析装置的灵敏度得到大幅度的提高.对其理论扣实验技术进行了研究和尝试,并用于铝合金中铜的测定,实验结果令人满意.     

一种确定煤基吸附剂内各扩散系数的简易方法

多孔介质内的扩散有分子扩散和表面扩散两种。在吸附温度较高时 ,表面扩散可忽略 ,而在温度较低的吸附过程中 ,两种扩散均须考虑。Ｓｃｈｎｅｉｄｅｒ和Ｓｍｉｔｈ[1 ] 曾用色谱法探讨了一种计算扩散系数的方法。他们认为等温吸附呈线性变化 ,引入了曲折系数 ,计算出分子扩散系数 (下称气相扩散系数 ) ,表面扩散系数 (下称吸附相扩散系数 )则由综合扩散系数减去分子扩散系数得到。文献 [2 ]则认为吸附过程非线性变化 ,服从Ｆｒｕｎｄｌｉｃｈ方程或Ｌａｎｇｍｕｉｒ方程。从质量平衡方程得出相对吸附量方程 ,再求出各扩散系数。前一种方法将…     

单标准FIA梯度校正催化动力学的光度测定法

催化动力学光度测定法有较高的灵敏度和选择性,但对实验条件要求苛刻,操作复杂,再现性较差。流动注射分析法(FIA)的引入简化了催化动力学测定的操作步骤,提高了再现性,然而连续FIA方法仅适用于催化反应较快的体系,本文将微机与FIA在线联机,利用FIA停流技术提高测试灵敏度,由FIA梯度校正原理用单标准溶液制备“标准系列,建     

三种芳烃溶剂在低密度聚乙烯膜材料中无限稀释扩散系数的测定

用气相色谱法测定了苯、甲苯和乙苯在固定液低密度聚乙烯中的保留时间和半峰宽,运用vanDeemter模型进行数据处理,得到3种芳烃小分子在低密度聚乙烯膜材料中的无限稀释扩散系数.     

水、甲醇和乙醇溶剂在PVA膜材料中无限稀释扩散系数测定

用气相色谱法研究小分子溶剂与聚合物材料之间的相互作用是一种快速、准确和方便的方法,该方法可以测量多种小分子溶剂在聚合物中的溶解和扩散行为.采用该方法测定了水、甲醇、乙醇在固定液PVA中的保留时间和半峰宽,运用van Deemter模型进行数据处理,得到了上述几种小分子在PVA膜材料中的无限稀释扩散系数,获得了有意义的结果.     

非极性烷烃溶剂在聚乙烯膜中无限稀释扩散系数的测定

气相色谱法研究小分子溶剂与聚合物材料之间的相互作用是一种快速、准确、方便的方法,该方法可以用来研究多种小分子溶剂在聚合物中的溶解和扩散行为.通过气相色谱法测定了3种小分子烷烃溶剂(正庚烷、正壬烷和正癸烷)在固定液聚乙烯中的保留时间和半峰宽,用vanDeemter模型进行数据处理,得到3种小分子在聚乙烯膜中的无限稀释扩散系数.     

Flow injection analysis methods for determination of diffusion coefficients

Two flow injection analyses (FIA) methods for the determination of diffusion coefficients in a straight single tube FIA system were developed. Based on the analytical solution of the convection-diffusion equation, linear relationships of the logarithmic values of the dispersion coefficient (D) and the half-peak width (W_1/2) with the diffusion coefficient (D_m) were obtained. Experiments were designed to verify these methods. For example, for potassium hexacyanoferrate (III) a D_m value of 0.72 × 10⁵ cm² s⁻¹ was found versus a literature value of 0.76 × 10⁵ cm² s⁻¹ (error, 5%). For potassium hexacyanoferrate (II) a D_m value of 0.67 × 10⁵ cm² s⁻¹ was obtained versus a literature value of 0.63 × 10⁵ cm² s⁻¹ (error, 6%). The diffusion coefficients of some important biomedical compounds, such as dopamine, epinephrine, norepinephrine and ascorbic acid, were then determined. The values of 10⁵ D_m/cm² s⁻¹ are 0.60 ± 0.03, 0.44 ± 0.02, 0.60 ± 0.01 and 0.68 ± 0.06, respectively.     

Studies on peak width measurement-based FIA acid-base determinations

Summary Studies on Peak Width Measurement-Based FIA Acid-Base Determinations Peak width measurement is employed to determine strong acid or base concentrations by injection into an aqueous indicator flowstream. Investigated parameters include concentration and pK of the indicator, dimensions and nature of the dispersion tube, signal level employed for peak width measurement, sample volume, carrier flow rate, viscosity of the carrier stream and the diffusion coefficient of the analyte.     

Stopped-flow injection analysis. The influence of diffusion on dispersion of normal and reverse flow injection

A relationship is derived to enable the comparison of the dispersion heights of normal and reverse flow injection analysis (FIA). A single channel flow system is employed in the absence of a chemical reaction. The stopped-flow injection method is used to probe the influence of molecular diffusion on the overall dispersion of normal and reverse FIA, which appeared to demonstrate fundamentally different diffusion behaviors. Small discrepancies are observed between the dispersion heights, which are enhanced by the stopped-flow period, especially when unmatched matrix ionic compositions of the indicator and counter solutions were involved. For these conditions, the diffusion flux rate is enhanced considerably, displaying a peak, in addition to the transient, for both methods. The influence of diffusion on the dispersion characteristics of normal and reverse FIA is discussed theoretically. Diffusion in the proposed model is postulated to oppose dispersion by convection. The latter initiates concentration gradients in the injection zone and propagates it with flow time over the dispersion zone profile. The diffusion flux then reacts in order to confine the indicator dispersion for normal FIA and to enhance it for reverse FIA. This model is consistent with the experimental results and accounts for most of the phenomena encountered. Probably owing to the influence of secondary flow phenomena, the use of coiled tubes has suppressed the effects of diffusion on the overall dispersion behavior.Part of the experimental work was performed at IMI Institute for Research and Development, Haifa, Israel.     

Reversed flow injection and sandwich sequential injection methods for the spectrophotometric determination of copper(II) with cuprizone

Two new flow methods, flow injection analysis (FIA) and sequential injection analysis (SIA), for the spectrophotometric determination of Cu(II) in water at trace levels have been developed and optimised. Both methods are based on the reaction with oxalic acid bis(cyclohexylidene hydrazide) (cuprizone) in alkaline media. The two procedures have been developed for the final aim to compare their performances and to offer new rapid heavy metals analysis tools, avoiding the use of extraction steps. A detailed study of the physico-chemical parameters affecting the systems performances has been carried out. The reversed FIA and sandwich SIA approaches offered the best sensitivity. In both cases, an extremely good linearity has been obtained within the range 0.06-4 μg ml⁻¹ (correlation coefficient r=0.9999), whereas the observed detection limits were 0.013 and 0.004 μg ml⁻¹, for FIA and SIA, respectively. Furthermore, due to the great similarity of the diffusion zones in the reaction slugs, our approach offers the opportunity to compare the two methods in analogous conditions. This SIA method, besides keeping its typical reagent saving features, offered analytical performances equivalent to those of FIA. To obtain these results, an original “stop-flow like” method was successfully employed in the SIA approach. Both methods were validated by analysis of real water samples, after copper addition, and certified reference samples of fortified and waste waters.     

折射＼率对流动注射峰形影响的研究

本文利用折射定律、菲涅耳公式和流体力学原理研究不同浓度乙醇溶液为试剂或载流的单流路体系中，正向流动注射与反向流动注射的信号峰形，对每个正、负峰高度和位置进行解释。给出不同相界面曲面方程，计算不同条件下反射率，反射光和折射光被流通池壁吸收时的径向半径及发生全反射时的径向半径，从理论上计算各种条件下的吸光度。     

A Study on the Peak Type of Flow Injection Analysis

Abstract

Two equations for justifying whether a FIA peak is a gamma peak or an exponentially modified Gaussian (EMG) peak or neither of them have been presented. From these two equations, the peaks of flow injection extraction and FIA with single-line and two-line manifolds obtained in this paper are gamma peaks.     

Flow-injection systems for determination of trace manganese in various salts by catalytic photometric detection

Two flow-injection analysis (FIA) systems for the determination of trace manganese in salts are presented using highly sensitive catalytic detection based on the oxidation of 3,4-dihydroxybenzoic acid by hydrogen peroxide. Two different approaches, the use of a large sample volume injection in a usual FIA mode (system A) and on-line coupling of a cation-exchange separation column with detection in a continuous flow system (system B), have proved very effective for eliminating the blank peak problem and thus affording direct injection of a sample solution containing a large concentration of salt. The limits of determinations are 0.04 ppm and 0.01 ppm for systems A and B respectively, when a 5 g sample is used for preparing the 100 ml sample solution. The proposed FIA systems were satisfactorily applied to the determination of manganese at 0.03-1.59 ppm in solar salts (salts made by exposing brine to the sun) with good precision.     

Fabrication of Photoelectrochemical Glucose Biosensor in Flow Injection Analysis System Using ZnS/CdS‐Carbon Nanotube Nanocomposite Electrode

In this work, a photoamperometric glucose biosensor based on glucose oxidase (GODx) was developed in flow injection analysis (FIA) system using ZnS‐CdS quantum dot (QD) modified multiwalled carbon nanotube/glassy carbon electrode (ZnS‐CdS/MWCNT/GCE). Cyclic voltammograms of the proposed electrode (GODx/ZnS‐CdS/MWCNT/GCE) showed a pair of well‐defined reversible redox peak attributing that direct electron transfer between the protein and electrode. The current of the reduction peak became more cathodic in the presence of O₂ due to the electrocatalytic activity of the electrode towards the reduction of dissolved O₂, but reduction current shifted to a less negative value upon addition of glucose in the solution. The obtained CV currents were affected by the irradiation of the electrode surface. Thus, the photoelectrochemical biosensing of glucose in the FIA system was studied by monitoring of the changes in the electrocatalyzed reduction peak current of dissolved O₂ at the proposed electrode dependent on glucose concentration. The proposed photoelectrochemical FIA method has a linear response to glucose ranging from of 0.01 to 1.0 mM with detection limit of 3.0 μM under optimized conditions. Photoelectrochemical biosensor was successfully fabricated in FIA system for selective, sensitive and repeatable detection of glucose and has been satisfactorily applied to determination of glucose in real sample.