壁面加热湍流相干结构的子波分析实验研究

通过在平板湍流边界层沿流向固壁表面平行放置若干条通电加热的金属细丝,在平板表面形成沿展向周期性分布的温度场,利用该温度场引起的空气热对流,在湍流边界层近壁区域产生一组沿湍流边界层展向周期分布的大尺度流向涡结构,改变了平板湍流边界层中不同尺度结构及其能量分布。采用对壁湍流多尺度结构的子波分析表明,在湍流边界层近壁区域产生规则的流向涡结构将壁湍流各种尺度湍涡结构不规则的脉动有序地组织起来,抑制了壁湍流各种尺度湍涡结构脉动,特别抑制了能量最大尺度湍涡结构的脉动,减小由于湍流脉动引起的在湍流边界层法向和展向的动量和能量损耗,从而减小了湍流的阻力。     

金属丝壁面加热湍流标度律的实验研究

通过在固壁表面的平板湍流边界层沿流向平行放置若干通电加热的金属细丝,在平板表面形成沿展向周期性分布的温度场,利用该温度场引起的空气热对流,在湍流边界层近壁区域产生一组沿湍流边界层展向周期分布的流向涡结构。对壁湍流小尺度结构标度律统计特性的研究表明,金属丝加热后形成的规则流向涡结构将壁湍流各种尺度湍涡结构不规则的脉动有序地组织起来,增强了湍流小尺度结构的层次结构相似性,减小了壁湍流中小尺度结构的间歇性和奇异性,抑制了壁湍流中奇异的湍涡结构。     

FLOW STRUCTURE IN THE TURBULENT BOUNDARY LAYER OVER DIRECTIONAL RIBLETS SURFACES

本文采用时间解析的二维粒子图像测速技术,对零压力梯度光滑以及汇聚和发散沟槽表面平板湍流边界层统计特性和流动结构进行了研究.结果表明在垂直于汇聚和发散沟槽表面的对称平面内,相对于光滑壁面,发散沟槽壁面使当地边界层厚度、壁面摩擦阻力、湍流脉动、雷诺应力等明显减小;而汇聚沟槽壁面对湍流边界层特性和流动结构的影响正好相反,汇聚沟槽使壁面流体有远离壁面向上运动的趋势,因而导致边界层厚度增加了约43%;同时,在汇聚沟槽表面情况下流向大尺度相干结构更容易形成,这对减阻是不利的.此外,顺向涡数量在湍流边界层的对数区均存在一个极大值,发散沟槽表面所对应的极大值位置更靠近沟槽壁面,而在汇聚沟槽表面则有远离壁面的趋势,由顺向涡诱导产生的较强的喷射和扫掠运动会在湍流边界层中产生较强的剪切作用,顺向涡数量的减少是发散沟槽壁面当地摩擦阻力降低的主要原因.     

沟槽方向对湍流边界层流动结构影响的实验研究

本文采用时间解析的二维粒子图像测速技术,对零压力梯度光滑以及汇聚和发散沟槽表面平板湍流边界层统计特性和流动结构进行了研究.结果表明在垂直于汇聚和发散沟槽表面的对称平面内,相对于光滑壁面,发散沟槽壁面使当地边界层厚度、壁面摩擦阻力、湍流脉动、雷诺应力等明显减小;而汇聚沟槽壁面对湍流边界层特性和流动结构的影响正好相反,汇聚沟槽使壁面流体有远离壁面向上运动的趋势,因而导致边界层厚度增加了约43%;同时,在汇聚沟槽表面情况下流向大尺度相干结构更容易形成,这对减阻是不利的.此外,顺向涡数量在湍流边界层的对数区均存在一个极大值,发散沟槽表面所对应的极大值位置更靠近沟槽壁面,而在汇聚沟槽表面则有远离壁面的趋势,由顺向涡诱导产生的较强的喷射和扫掠运动会在湍流边界层中产生较强的剪切作用,顺向涡数量的减少是发散沟槽壁面当地摩擦阻力降低的主要原因.     

Spalding公式在脊状表面湍壁摩擦力测量中的应用

在低速风洞中来流速度一定的情况下使用IFA300恒温热线风速仪测量了光滑表面和两种不同尺寸的脊状表面湍流边界层平均速度分布剖面,并验证了试验段湍流发展的充分性;通过应用Spalding壁面公式使用最小二乘法精准拟合了实验测量的边界层内层速度分布曲线,得到了湍流边界层壁面摩擦速度并进一步求得湍流壁面摩擦应力,较准确地计算出脊状表面的虚拟原点位置,并通过与对数律公式拟合结果比较分析,证实了该方法更加准确有效. 最后分别计算了3种实验模型的湍流边界层动量损失厚度. 通过对比脊状表面与光滑表面动量损失厚度和壁面摩擦应力,反映了动量损失厚度的大小与壁面摩擦应力的大小具有一致性,充分证实了脊状表面在湍流中具有一定的减阻效果.      

用平均速度剖面法测量壁湍流摩擦阻力

用IFA300恒温热线风速仪精细测量风洞中不同雷诺数流动条件下的平板湍流边界层近壁区域对数律平均速度剖面．利用平板湍流边界层近壁区域的对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系,在准确测量平板湍流边界层近壁区域对数律平均速度剖面的基础上,测量平板湍流边界层的壁面摩擦阻力．实现了平板湍流边界层壁面摩擦阻力的无干扰或微小干扰测量．该种方法操作简便,不需要在流场中安装测力天平、传感器等复杂的测量装置,不需要对湍流边界层的壁面进行破坏,不会影响湍流边界层壁面附近区域原有的流场条件,是一种切实可行的测量平板湍流边界层壁面摩擦阻力的简便方法．     

TRPIV MEASUREMENT OF DRAG-REDUCTION IN THE TURBULENT BOUNDARY LAYER OVER RIBLETS PLATE

采用高时间分辨率粒子图像测速技术对沟槽壁面平板湍流边界层速度矢量场的时间序列及其统计量进行了实验测量,讨论了在同一来流速度下沟槽壁面对平均速度剖面﹑雷诺切应力及湍流强度的影响. 用流向速度分量的多尺度空间局部平均结构函数辨识壁湍流多尺度相干结构,用条件采样和相位平均技术提取壁湍流多尺度相干结构喷射和扫掠事件的脉动速度、展向涡量的二维空间拓扑形态. 结果表明,与同材料光滑壁面对比,沟槽壁面实现了10.73%的摩阻减小量;沟槽壁面湍流边界层湍流强度及雷诺切应力皆比光滑平板湍流边界层对应统计量小,说明沟槽壁面有效降低了湍流边界层内流体的脉动. 通过比较壁湍流相干结构猝发事件各脉动速度分量与展向涡量的空间分布特征,肯定了沟槽壁面的减阻效果,发现沟槽壁面通过抑制相干结构猝发事件实现减阻.     

湍流边界层流场与噪声实验研究

在重力式水洞中进行了水翼及半翼湍流边界层流场与噪声的实验研究。测量了水翼及半翼边界层附近的湍流脉动速度场;测量了半翼翼型表面三点处的压力脉动及其辐射噪声,测量了水翼内部测点的噪声及外部辐射噪声,在不同流速、不同攻角、光滑和粗糙翼面的情况下都进行了测量分析。试验结果发现,上述因素对模型的边界层湍流速度场有显著影响,15度攻角时,翼面附近湍流强度要比0度时大得多,粗糙翼面附近的湍流强度比光滑的大,而湍流强度随来流速度的变化不大,u(来流）方向和v方向的湍流强度量级相当;一般地,翼面压力脉动、翼内部噪声及外部噪声都是随来流速度的增大而增大,随攻角的增大而增大,粗糙翼面时的结果要比光滑翼面的大。从压力脉动与噪声测量结果与相应的流场测量结果比较可知,可以从湍流区域的湍流强度来判断出声源强度的定性变化。     

脊状表面减阻机理研究

针对脊状表面流场的特点,通过实验测量和数值模拟的方法对脊状表面微观流场进行了深入研究,获得了脊状表面湍流边界层的时均速度分布曲线、湍流度分布曲线和微观流场结构.为了得到脊状结构对壁面物性的影响,对脊状表面进行了疏水性测试,获得了液滴在脊状表面上的表观接触角,并通过水洞试验验证了脊状表面的减阻效果.研究表明,与光滑表面相比,脊状表面微观流场结构中存在"二次涡",近壁区的黏性底层厚度比平板的要厚得多,湍流度显著降低,且脊状表面表现出明显的疏水性.由此提出了基于壁面隔离效应、增大湍流阻尼效应和改变壁面物性效应的减阻机理.     

二维平板湍流边界层减阻研究

利用一套以位移传感器为主的弹性平衡装置,测量几种不同表面形状设计的平板在充分发展的二维湍流边界层中的减阻效果,并对其减阻机理进行研究。结果表明,大涡破碎器 LEBU(Large Eddy Break-up)和其它减阻装置的形状和布置对表面摩擦阻力有较大影响,在有些设计状态下的平板得到了净减阻。     

Estimation of the acoustic emission spectrum of a boundary layer on a rough surface

Under engineering conditions the surfaces over which fluids flow are not usually hydraulically smooth. In this connection it is important to investigate the generation of sound by a turbulent boundary layer on a rough surface. Turbulent flow over a deformed surface creates dipole sources of sound, which may considerably increase the acoustic emission as compared with the quadrupole emission from a boundary layer on a smooth plate [1, 2]. In the case of sandy roughness estimates of the acoustic field are usually based on the energy summation of the fields generated by flow over the individual roughness elements [3, 4]. In this case not easily verifiable assumptions are made concerning the nature of the turbulent flow near the roughness, and the intensity of the emission is found correct to a constant factor subject to experimental determination. In the present study, in order to calculate the acoustic emission of a boundary layer on a surface with sandy roughness, it is proposed to employ the available experimental data on the cross of the surface pressure.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 20–26, September–October, 1985.     

Numerical prediction of turbulent boundary layer noise from a sharp-edged flat plate

An efficient hybrid uncorrelated wall plane waves–boundary element method (UWPW-BEM) technique is proposed to predict the flow-induced noise from a structure in low Mach number turbulent flow. Reynolds-averaged Navier-Stokes equations are used to estimate the turbulent boundary layer parameters such as convective velocity, boundary layer thickness, and wall shear stress over the surface of the structure. The spectrum of the wall pressure fluctuations is evaluated from the turbulent boundary layer parameters and by using semi-empirical models from literature. The wall pressure field underneath the turbulent boundary layer is synthesized by realizations of uncorrelated wall plane waves (UWPW). An acoustic BEM solver is then employed to compute the acoustic pressure scattered by the structure from the synthesized wall pressure field. Finally, the acoustic response of the structure in turbulent flow is obtained as an ensemble average of the acoustic pressures due to all realizations of uncorrelated plane waves. To demonstrate the hybrid UWPW-BEM approach, the self-noise generated by a flat plate in turbulent flow with Reynolds number based on chord Re_c = 4.9 × 10⁵ is predicted. The results are compared with those obtained from a large eddy simulation (LES)-BEM technique as well as with experimental data from literature.     

Finite Difference Method for the Acoustic Radiation of an Elastic Plate Excited by a Turbulent Boundary Layer: A Spectral Domain Solution

A finite difference method is developed to study, on a two-dimensional model, the acoustic pressure radiated when a thin elastic plate, clamped at its boundaries, is excited by a turbulent boundary layer. Consider a homogeneous thin elastic plate clamped at its boundaries and extended to infinity by a plane, perfectly rigid, baffle. This plate closes a rectangular cavity. Both the cavity and the outside domain contain a perfect fluid. The fluid in the cavity is at rest. The fluid in the outside domain moves in the direction parallel to the system plate/baffle with a constant speed. A turbulent boundary layer develops at the interface baffle/plate. The wall pressure fluctuations in this boundary layer generates a vibration of the plate and an acoustic radiation in the two fluid domains. Modeling the wall pressure fluctuations spectrum in a turbulent boundary layer developed over a vibrating surface is a very complex and unresolved task. Ducan and Sirkis [1] proposed a model for the two-way interactions between a membrane and a turbulent flow of fluid. The excitation of the membrane is modeled by a potential flow randomly perturbed. This potential flow is modified by the displacement of the membrane. Howe [2] proposed a model for the turbulent wall pressure fluctuations power spectrum over an elastomeric material. The model presented in this article is based on a hypothesis of one-way interaction between the flow and the structure: the flow generates wall pressure fluctuations which are at the origin of the vibration of the plate, but the vibration of the plate does not modify the characteristics of the flow. A finite difference scheme that incorporates the vibration of the plate and the acoustic pressure inside the fluid cavity has been developed and coupled with a boundary element method that ensures the outside domain coupling. In this paper, we focus on the resolution of the coupled vibration/interior acoustic problem. We compare the results obtained with three numerical methods: (a) a finite difference representation for both the plate displacement and the acoustic pressure inside the cavity; (b) a coupled method involving a finite difference representation for the displacement of the plate and a boundary element method for the interior acoustic pressure; (c) a boundary element method for both the vibration of the plate and the interior acoustic pressure. A comparison of the numerical results obtained with two models of turbulent wall pressure fluctuations spectrums - the Corcos model [3] and the Chase model [4] - is proposed. A difference of 20 dB is found in the vibro-acoustic response of the structure. In [3], this difference is explained by calculating a wavenumber transfer function of the plate. In [6], coupled beam-cavity modes for similar geometry are calculated by the finite difference method. This revised version was published online in July 2006 with corrections to the Cover Date.     

可渗透壁对翼型声涡相互作用下流场及声场的影响

由仿生学原理构建的可渗透翼型对湍流气动噪声抑制作用已展现良好的应用前景。对NACA 0012可渗透翼型和实体翼型进行了数值计算,得到了声涡相互作用下气动噪声声场和流场,分析了可渗透壁对翼型流场和声场的影响。研究表明,相对实体翼型,可渗透壁通过减小声源强度降低了主纯音噪声声压级幅值和远场总声压级,消除了高阶离散纯音,但对噪声的指向性没有较大改变。进一步的流场分析表明,可渗透壁对翼型气动性能影响不大的情况下能够降低边界层扰动和翼型后缘大尺度涡旋强度,并推迟分离泡转捩和再附位置。     

Effect of surface roughness on a turbulent wall-attaching offset jet

The flow characteristics of a two-dimensional offset jet discharged parallel to a rough wall is experimentally investigated by using a split film probe. The distributions of the mean velocity and turbulent stresses in the flow field are obtained and compared with those of the wall attaching offset jet on a smooth wall. It is found that the wall-attaching region on the rough wall is longer than on the smooth wall for the same offset height and the jet speed. The normal distance of the maximum velocity point is farther away from the wall than that for the smooth wall case because of the thick wall boundary layer established by the surface roughness. It is also found that the roughness of the wall accelerates the relaxation process towards redeveloped plane wall jet and that it exhibits a quite different turbulent diffusion behavior especially near the wall from that in the wall jet over a smooth surface.     

Structures of Density Fluctuations at a Low-Mach-Number Turbulent Boundary Layer by DNS

We performed a direct numerical simulation of a low-Mach-number turbulent boundary layer using fundamental equations of compressible flow to investigate the relation between vortex structures and the density distribution. A fully developed turbulent boundary layer of compressible flow was reproduced in the simulation. From the turbulence statistics and instantaneous structures of the density fluctuation, we identified different features in the three regions of a near-wall field, far field and flow field outside the turbulent boundary layer. Structures of the density fluctuation could correspond to sound sources in a turbulent boundary layer. We then observed fine-scale structures of the density fluctuation that were strongly related to turbulent vortices in the vicinity of the wall. In addition, there were large-scale density structures in the upper boundary layer. The large-scale structures seem to correlate with the fine-scale structures close to the wall, with there being a non-steady larger-scale density fluctuation profile in the outer region of the boundary layer.     

Study of turbulent boundary layers on smooth and rough surfaces with arbitrary pressure gradients

The results of an experimental investigation into the steady-state plane turbulent boundary layer in an incompressible liquid at an impermeable wall are presented. Cases of flow at smooth and rough surfaces in the presence of a longitudinal pressure gradient are considered. The results of measurements of the turbulent structure of the flow at various distances from the channel inlet are presented. A detailed analysis of the kinematic and dynamic characteristics of the flow is given. Special attention is paid to the boundary region of the flow close to the wall. A universal law is proposed for the variation in the local resistance coefficient along the boundary layer.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 3, pp. 126–134, May–June, 1971.     

Wall shear stress measurement in a turbulent pipe flow using ultrasound Doppler velocimetry

A turbulent boundary layer of a water flow is investigated by means of pulsed ultrasound Doppler velocimetry. The advantage of this method is the acquisition of complete velocity profiles along the sound propagation line within very short time intervals. The shear stress velocity, used for normalizing the velocity profiles, was determined by fitting the profiles to the universal profiles in a turbulent boundary layer obtained from Prandtl's mixing length theory. A coordinate transformation in the near-wall region is proposed to allocate the velocity data to "true" wall distances. From the experimental values of the wall shear stress velocity, the friction factors for a turbulent pipe flow are calculated and compared to the Blasius law. The overall error in measurement was estimated to NJ.4%.     

ON THE MECHANISM OF TURBULENT COHERENT STRUCTURE（II）──A PHYSICAL MODEL OF COHERENT STRUCTURE FOR THE ROUGH BOUNDARY LAYER

（刘宇陆）（蔡树棠）ＯＮＴＨＥＭＥＣＨＡＮＩＳＭＯＦＴＵＲＢＵＬＥＮＴＣＯＨＥＲＥＮＴＳＴＲＵＣＴＵＲＥ（ＩＩ）──ＡＰＨＹＳＩＣＡＬＭＯＤＥＬＯＦＣＯＨＥＲＥＮＴＳＴＲＵＣＴＵＲＥＦＯＲＴＨＥＲＯＵＧＨＢＯＵＮＤＡＲＹＬＡＹＥＲ￥ＬｉｕＹｕｌｕ；Ｃ...