十二烷基三甲基溴化铵在聚苯乙烯胶乳粒子上的吸附

实验测得C~1~2TAB在PS胶乳粒子表面的吸附等温线呈L型的二阶段吸附特征,这表明初始的C~1~2TA^+离子是将其季铵正电性头基吸引在PS链的负电性硫酸根端基上,并将碳氢链通过疏水相互作用吸附在PS链上。结合光子相关谱测得胶乳粒子流体力学半径R~H的变化,表明第I阶段围绕着这些初始吸附位的聚集吸附,产生平均聚集数为4.0的松散小聚集体,此时对应的浓度c/cmc=0.32是文献通常所指的临界表面胶团浓度csmc。其后的进一步聚集吸附最终生成了附着在PS链端基处且平均聚集数为19.5的球形吸附胶团。这一饱和吸附的结果增加了胶乳粒子在水溶液中的分散稳定性。     

Early-stage flocculation kinetics of polystyrene latex particles with polyelectrolytes studied in the standardized mixing: Contrast of excess and moderate polyelectrolyte dosage

Standardized mixing procedure was applied to the analysis of flocculation of polystyrene latex (PSL) particles with polyelectrolytes. After confirming the initial enhancement of flocculation rate in the very beginning followed by abrupt stop with excess dosage, attention was shifted to the system of moderate dosage. In the former, effects of ionic strength were further analyzed to find the consistency with adsorption isotherm. In the latter, flocculation started slowly in the beginning, sometime slower than salt-induced rapid coagulation, however, the rate gradually increases in the middle stage. Often, the increased rate exceeds that of salt-induced rapid coagulation. This behavior emerged more clearly in the case of lower ionic strength. This is the indication that the rate of relaxation of polymer on the colloidal surface is a function of surface coverage and ionic strength. The ultimate degree of flocculation is usually higher than that observed for excess dosage. The size distribution of flocs was also examined, however, no clear difference between different experimental conditions was confirmed for the same degree of flocculation.     

Adsorption of cationic polyelectrolyte onto a model carboxylic latex and the influence of adsorbed polycation on the charge regulation at the latex surface

 Adsorption of a well-characterized cationic polyacrylamide (CPAM) onto the surface of a model colloid (monodisperse polystyrene latex with carboxylic functional groups) was studied over a wide range of pH (4–9) and KCl concentration (c _s =10^-3–0.3 M). The surface charge density of the latex particles with and without adsorbed CPAM was also measured over the same range of electrolyte compositions. The adsorbed amount of CPAM increases with increase in c _s and pH. The polyelectrolyte adsorption alters substantially the surface charge density of the latex particles as compared to the polymer-free case. A large overcompensation of the surface charge by the adsorbed polyelectrolyte is established at high c _s and low pH. A qualitative explanation of the observed features is put forward. Received: 3 December 1996 Accepted: 20 January 1997     

Role of the electrostatic interactions on the basic or acidic hydrolysis kinetics of poly-( , -lactide) monolayers

The hydrolysis kinetics of insoluble poly-( , -lactide) monolayers spread on basic or acidic aqueous subphase were followed by measuring simultaneously the decrease in the surface area at constant surface pressure and the evolution of the surface potential. An approach to analyse the role of the electrostatic interactions during the hydrolysis at alkaline pH, interpreting the surface potential data was developed. The theoretical predictions based on the idea of a random fragmentation of polymer molecules leading to the interfacial accumulation of charged insoluble products and solubilisation of small fragments describes well the experimental results. The reversibility of the hydrolysis/esterification reaction at acidic pH is taken into account.     

Numerical study of the interplay of monomer-surface electrostatic and non-electrostatic interactions in the adsorption of weak polyelectrolytes on oppositely charged surfaces

The adsorption of weak polybase on oppositely charged planar surfaces has been investigated numerically by using the self-consistent field theory (SCFT). Particular attention was paid to the interplay of monomer-surface electrostatic and non-electrostatic interactions in the adsorption behaviors of weak polybase. In this study, the strength of monomer-surface non-electrostatic interactions was set to be no more than the thermal energy k _B T. It was found from the numerical study that in the regime of low surface charge density of the substrate and low pH or high bulk degree of ionization, both the screening-enhanced and screening-reduced salt effects emerge. On the contrary, in the opposite regime, only the screening-reduced salt effect was observed. Moreover, the overall charge neutrality inside the adsorption layer was analyzed. The underlying mechanism governing the adsorption behaviors of weak polybase on oppositely charged surfaces was elucidated.     

Synthesis and characterization of novel core-shell colloidal particles ZnO/poly(ethylcyanoacrylate)

Here we report the synthesis and physicochemical characterization of novel hybrid core/shell type ZnO/poly(ethylcyanoacrylate) colloidal particles. It is expected that coating ZnO colloidal particles with biocompatible and biodegradable poly(alkylcyanoacrylates) will pave the way toward the potential application of ZnO colloidal particles in biomedical research. Recent findings of cell selective toxicity indicate a potential utilization of ZnO colloidal particles in the treatment of cancer. For this purpose, ZnO colloidal particles have to be selectively delivered to the site of action by a suitable biocompatible and biodegradable carrier system. Toward this goal, poly(alkylcyanoacrylates) meet ideally the requirements for carrier systems in drug delivery due to their biocompatibility, biodegradability, low toxicity, and ability to overcome the multidrug resistance in cancer cells.     

Determination of colloidal and dissolved silver in water samples using colorimetric solid-phase extraction

The increase in bacterial resistance to antibiotics has led to resurgence in the use of silver as a biocidal agent in applications ranging from washing machine additives to the drinking water treatment system on the International Space Station (ISS). However, growing concerns about the possible toxicity of colloidal silver to bacteria, aquatic organisms and humans have led to recently issued regulations by the US EPA and FDA regarding the usage of silver. As part of an ongoing project, we have developed a rapid, simple method for determining total silver, both ionic (silver(I)) and colloidal, in 0.1-1 mg/L aqueous samples, which spans the ISS potable water target of 0.3-0.5 mg/L (total silver) and meets the US EPA limit of 0.1 mg/L in drinking water. The method is based on colorimetric solid-phase extraction (C-SPE) and involves the extraction of silver(I) from water samples by passage through a solid-phase membrane impregnated with the colorimetric reagent DMABR (5-[4-(dimethylamino)benzylidene]rhodanine). Silver(I) exhaustively reacts with impregnated DMABR to form a colored compound, which is quantified using a handheld diffuse reflectance spectrophotometer. Total silver is determined by first passing the sample through a cartridge containing Oxone, which exhaustively oxidizes colloidal silver to dissolved silver(I). The method, which takes less than 2 min to complete and requires only ∼1 mL of sample, has been validated through a series of tests, including a comparison with the ICP-MS analysis of a water sample from ISS that contained both silver(I) and colloidal silver. Potential earth-bound applications are also briefly discussed.     

Synthesis,characterization, and stability of carbodiimide groups in carbodiimide‐functionalized latex dispersions and films

Cyclohexylcarbodiimidoethyl methacrylate (CCEMA) and t‐butylcarbodiimidoethyl methacrylate (t‐BCEMA) were prepared in a two‐step synthesis. These monomers were then used to prepare carbodiimide‐functionalized PBMA and PEHMA latex particles, employing two‐stage emulsion polymerization, with the carbodiimide–methacrylate monomers being introduced only in the second stage under monomer‐starved conditions. During emulsion polymerization, the carbodiimide moiety ( NCN ) was found to be unstable at pH 4, but stable when the pH of the dispersion was increased to 8, using NaHCO₃ as the buffer. Survival of  NCN group against hydrolysis during the polymerization, and during storage in the dispersion, was enhanced by using EHMA as the comonomer (more hydrophobic) and the t‐butyl carbodiimide derivative. The t‐butyl group provides more steric hindrance to the hydrolysis reaction. A decrease in the reaction temperature from 80°C to 60°C was also found to increase the extent of  NCN group incorporation during emulsion polymerization. Under ideal conditions, more than 98% of the  NCN groups in the monomer feed are successfully incorporated into the latex. When these latex particles are mixed with a  COOH containing latex and allowed to dry, polymer diffusion leading to crosslinking occurs. Films annealed at 60°C reach a gel content of 60% in 10 h. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 855–869, 2000     

Isothermal equilibrium adsorption of concanavalin A on dextran-modified poly(methyl methacrylate) latex particles

Isothermal equilibrium adsorption experiments were carried out to study the adsorption of concanavalin A (Con A) on dextran-modified poly(methyl methacrylate) (PMMA) latex particles. Three PMMA particles with various levels of dextran modification were selected for study: 0% (designated as D0), 1.24% (D20), and 2.45% (D75) based on total polymer weight. The Langmuir model is applicable to both D0 and D20 systems, although the data for the D20 system are somewhat scattered. On the other hand, the amount of Con A adsorbed per gram polymer particles (q*) versus the Con A concentration in water (c*) curve for the D75 system cannot be described by the Langmuir model. The deviation is attributed to the formation of a crosslinked network structure, caused by specific binding of the dimeric Con A molecules onto two neighboring particles with grafted dextran. The ratio of the initial number of Con A molecules to the initial number of active binding sites on the dextran-modified particle surface plays an important role in determining the structure of flocs formed. The maximum amount of Con A adsorbed on the particle surface (q _max) is of the order of 10⁻¹ μmol per gram particles and q _max in decreasing order is D75 > D20 > D0. The dissociation constant of the Con A-D20 (or Con A-D75) pair is of the order of 10⁻¹ μmol dm⁻³ which is 1 order of magnitude smaller than that of the Con A-D0 pair. Thus, the electrostatic interaction between Con A and D0 is much weaker than the affinity interaction between Con A and D20 (or D75). An empirical model is proposed to qualitatively explain the q* versus c* data. Received: 18 June 1998 Accepted in revised form: 24 December 1998     

Synthesis of iron oxide/poly(methyl methacrylate) composite latex particles: Nucleation mechanism and morphology

A magnetic poly(methyl methacrylate) (PMMA) composite latex was prepared by soapless emulsion polymerization in the presence of ferrofluid, and the ferrofluid was prepared by means of a coprecipitation method. The effects of various polymerization parameters, such as the monomer concentration, ferrofluid content, and initiator concentration, on the conversion curve and particle size of the magnetic composite latex particles were examined in detail. The results showed that two nucleation mechanisms were involved according to the polymerization conditions. In the monomer‐rich and less ferrofluid system, self‐nucleation of PMMA was dominant over the entire course of emulsion polymerization. In the ferrofluid‐rich system, seeded emulsion polymerization was the main course to form the magnetic composite latex particles. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5695–5705, 2004     

Synthesis of ion-free latex particles composed of polybutadiene and poly (vinyl pyrrolidone) as polymer electrolyte materials

The synthesis of polybutadiene (PB) by emulsion polymerization with use of poly (vinyl pyrrolidone) (PVP) stabilizer was investigated. The goal was to prepare flexible latex films that clearly retain particle morphology in the solid state after heat treatment and contain no ionic, hydroxyl, or (primary, secondary) amino groups. The latex particle core composed of PB was nonpolar and rubbery, while the particle shell composed of PVP was polar and glassy. Average particle diameter was measured by the dynamic light scattering technique, and particles were imaged by scanning and transmission electron microscopic analyses. Dialysis of the latices resulted in successful exchange of the dispersion medium without precipitation. © 1994 John Wiley & Sons, Inc.     

Surface electric and titration behaviour of fumed oxides

Adsorption of Pb(II), Sr(II), and Cs(I) on fumed silica, alumina, titania, silica/titania (ST), silica/alumina (SA), and alumina/silica/titania (AST) reveals that mixed oxides containing titania have a greater adsorptive capability in respect to metal cations than individual and SA oxides. Pyrocarbon deposits on fumed oxides enhance the adsorption of metal ions. Calculations of electrophoretic potential (ζ) with consideration for the porosity of aggregates of primary particles of AST show a significant influence of surface alumina (at pH<8) and titania and silica (at pH>8) on the ζ values. The effective diameter of particles (D_ef) of fumed oxides in aqueous media depends on pH for AST stronger than for ST (between isoelectric points (IEPs) of titania and alumina). A significant difference in the pH values of IEP and point of zero charge is observed for AST samples. A pyrocarbon influence on the ζ potential depends on the type of oxide matrix, since ζ increases for certain samples but for others it decreases. These changes depend nonlinearly on pH as well as the secondary particle size distributions (SPSDs) and D_ef.     

Effect of size, proteic composition, and heat treatment on the colloidal stability of proteolyzed bovine casein micelles

The casein micelles of reconstituted nonfat milk that have been fractionated by controlled pore glass chromatography showed a relationship between their size and their proteic composition: The fractions containing the smaller particles were richer in κ-casein than the fractions containing the bigger ones, in accordance with the casein micelle model of submicelles. The initial aggregation rate of micelles of different sizes, partially proteolyzed with chymosin (para-casein micelles), was measured in conditions of enzyme excess in which aggregation is the rate-limiting step of enzymatic coagulation, showing higher rates for the smaller micelles with the production of less compact para-casein micelle networks. This behavior could be explained in terms of electrostatic and steric colloidal stabilization due to their lower negative net charge and size and to a higher surface density of hydrophobic “patches” of proteolyzed κ-casein related to a higher probability of effective collisions between particles. Differences in the β-casein content did not seem to affect the initial aggregation rate of the micelles. On the contrary, the modifications of the micelle surface by heating affected the colloidal stability of the hydrolyzed micelles in different ways. The denaturation of the whey proteins and the formation of covalent complexes with κ-casein modify the micelle surface, increasing specially the steric stabilization, and produces a diminution in the number of hydrophobic sites that could be able to give interparticle hydrophobic interactions.     

Surface structure and properties of poly-(ethylene terephthalate) hydrolyzed by alkali and cutinase

This study was aimed at comparatively investigating the hydrolysis of crystalline and amorphous poly-(ethylene terephthalate) films by alkali and cutinase. Changes of surface properties were investigated by FTIR spectroscopy (ATR mode). The A₁₃₄₁/A₁₄₁₀ and I₁₁₂₀/I₁₁₀₀ absorbance ratios, and the full width at half maximum of the carbonyl stretching band (FWHM₁₇₁₅) were used to evaluate the polymer crystallinity and its changes upon hydrolysis. The effect of different treatments on chain orientation was evaluated by calculating R ratios of appropriate bands. The spectroscopic indexes showed that both alkali and enzyme treatments induced structural and conformational rearrangements with a consequent increase in crystallinity in both amorphous and crystalline films. The crystalline PET film was modified more strongly by alkali than by cutinase, while the opposite occurred for the amorphous one. The trend of the water contact angle (WCA) clearly indicates that alkali is more effective than cutinase in enhancing hydrophilicity of PET films and that the effect is stronger on amorphous than on crystalline films. The values of WCA correlate well with the FTIR indexes calculated from the spectra of hydrolyzed crystalline PET films. The mechanism of the surface hydrolysis of PET by alkali and cutinase is discussed.     

含铅聚合物微凝胶与硫化氢反应前后在良溶剂中的分子扩散行为

用溶液聚合法制备出轻度交联的含铅微凝胶,用光子相关光谱技术测定其在良溶剂中与H₂S反应前、后的扩散行为,由外推法得到在浓度无限稀时的分子扩散系数,给出微凝胶的流体力学半径。结果表明:相同量的含铅微凝胶在不同的初始浓度下与H₂S反应,生成含PbS纳米微粒的凝胶;但其体积增大不同,这说明H₂S与含铅微凝胶的反应既可以在分子内也可以在分子间进行,分子间的反应使含硫化铅微凝胶扩散系数随浓度的变化曲线的线性范围变小。     

含铅聚合物微凝胶与硫化氢反应前后在良溶剂中的分子扩散行为

用溶液聚合法制备出轻度交联的含铅微凝胶,用光子相关光谱技术测定其在良溶剂中与H2S反应前、后的扩散行为,由外推法得到在浓度无限稀时的分子扩散系数,给出微凝胶的流体力学半径。结果表明:相同量的含铅微凝胶在不同的初始浓度下与H2S反应,生成含PbS纳米微粒的凝胶；但其体积增大不同,这说明H2S与含铅微凝胶的反应既可以在分子内也可以在分子间进行,分子间的反应使含硫化铅微凝胶扩散系数随浓度的变化曲线的线性范围变小。     

Ion-free latex films composed of fused polybutadiene and poly (vinyl pyrrolidone) particles as polymer electrolyte materials

Latex films composed of fused polybutadiene (PB) and poly (vinyl pyrrolidone) (PVP) particles that contain no ionic, hydroxyl, or amino groups were swelled with lithium salt solutions to yield new polymer electrolyte materials. The latex particle consists of a nonpolar, rubbery core that contains the PB component and a polar, glassy shell that contains the PVP component. The particle core-shell morphology was retained in the solid state, after the latex dispersion medium was removed and the films dried at high temperatures, due to the high T_g of the PVP shell. The films swelled when immersed in lithium salt solutions, and ionic conductivity of swollen films was greater than 10^-3 S/cm. Swelling and ionic conduction occurred only in the polar PVP component. Extraction of PVP occurred with extended swelling. © 1994 John Wiley & Sons, Inc.     

Polyelectrolyte complexes of soluble poly-2-[(methacryloyloxy)ethyl]trimethylammonium chloride and its hydrogels with poly(acrylic acid)

The complex formation of poly-2-[(methacryloyloxy)-ethyl]trimethylammonium chloride (PMADQUAT) with poly(acrylic acid) (PAA) of different molecular weights has been studied in aqueous solutions by potentiometric, viscometric, turbidimetric and FTIR spectroscopic methods. The formation of insoluble non-stoichiometric polyelectrolyte complexes has been shown. The stability of polyelectrolyte complexes in solutions of different pH and ionic strength has been evaluated. The formation of polyelectrolyte complexes between hydrogels of PMADQUAT and linear PAA of different molecular weights has been studied. It was shown that the molecular weight of PAA considerably affects the kinetics of interaction as well as the final state of gel-polymer complex.     

Adsorption, desorption and activities of acid phosphatase on various colloidal particles from an Ultisol

Adsorption, desorption and activity of acid phosphatase on various soil colloidal particles and pure clay minerals were studied. Higher adsorption amounts and low percentage of desorption of acid phosphatase were found on fine soil clays (<0.2 μm). Electrostatic force and ligand exchange are the major driving forces that are involved in the adsorption of enzymes on soil clays. More enzyme molecules were adsorbed on soil clays in the presence of organic components. However, enzymes on organic clays were more easily released. One-third of the enzyme on goethite was adsorbed via ligand exchange process. Some other interactions, such as van der Waals force, hydrophobic force and hydrogen bonding may be more important in the adsorption of enzyme on kaolinite and the enzyme in this system cannot be easily removed. Coarse clays (0.2–2 μm) and inorganic soil clays had higher affinities for enzyme molecules than fine clays and organic clays, respectively. The activity of enzyme bound on soil clays was inhibited and the thermal stability was increased in the presence of organic matter. Data obtained in this study are helpful for a better understanding of the interactions of enzymes with inorganic and organic constituents in soil and associated environments.     

Miscibility,specific interactions,and self‐assembly behavior of phenolic/polyhedral oligomeric silsesquioxane hybrids

The miscibility of a phenolic resin with polyhedral oligomeric silsesquioxane (POSS) hybrids and the specific interactions between them were investigated with Fourier transform infrared (FTIR) spectroscopy and wide‐angle X‐ray diffraction (WAXD). An analysis of the morphology and microstructure was performed with polarized optical microscopy and atomic force microscopy (AFM). The interassociation equilibrium constant between the phenolic resin and POSS (38.7) was lower than the self‐association equilibrium constant of pure phenolic (52.3) according to the Painter–Coleman association model. This result indicated that POSS was partially miscible with the phenolic resin. A polarized optical microscopy image of a phenolic/POSS hybrid material (20 wt % POSS) indicated that the crystals of POSS were arranged evenly in the phenolic matrix; the self‐assembled array of POSS crystals was also confirmed by AFM. This phenomenon was consistent with the FTIR spectroscopy and WAXD analyses. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1127–1136, 2004