A novel anode supported BaCe0.4Zr0.3Sn0.1Y0.2O3−δ electrolyte membrane for proton conducting solid oxide fuel cells

A novel BaCe_0.4Zr_0.3 Sn_0.1Y_0.2O_3−δ (BSY) electrolyte membrane with thickness of 20 μm was fabricated on NiO-based anode substrate via a one-step all-solid-state method followed by a co-sintering at 1450 °C for 5 h. Chemical stability test demonstrated that BSY electrolyte showed adequate chemical stability against CO₂ and H₂O at intermediate temperature. Besides, the doping of Sn also enhanced the conductivity in humidified hydrogen. With Nd_0.7Sr_0.3MnO_3−σ cathode and hydrogen fuel, the fuel cell generated maximum output of 320, 185 and 105 mW cm⁻² at 700, 650 and 600 °C, respectively. The interfacial resistance of the fuel cell was studied under open circuit conditions and the short-term cell performance also confirmed the stability of BSY electrolyte membrane.     

Mechanosynthesis of nanopowders of the proton-conducting electrolyte material Ba(Zr, Y)O3−δ

The formation of perovskite nanopowders of the common proton-conducting, electrolyte material Ba(Zr_1−xY_x)O_3−δ is demonstrated by room temperature mechanosynthesis for the compositional range x=0, 0.058 and 0.148. This is achieved with a planetary ball mill at 650 rpm in zirconia vials, starting from BaO₂ with ZrO₂, (ZrO₂)_0.97(Y₂O₃)_0.03 or (ZrO₂)_0.92(Y₂O₃)_0.08 precursors, respectively. Powder X-ray diffraction (XRD) reveals the formation of the perovskite phase in the early stages of milling with phase purity being achieved after milling times of 240 min for composition x=0.058 whereas 420 min is necessary for composition x=0.148. In contrast, traces of ZrO₂ are apparent in composition x=0 even after milling times of 420 min. The use of BaCO₃ as precursor does not allow the formation of the perovskite phase for any composition. The perovskite crystallites are spherical in shape with an average size determined from XRD of ca. 30 nm in agreement with transmission electron microscopy observations. FTIR spectra demonstrate that contamination levels of BaCO₃ in the mechanosynthesized powders are very low. The spherical shape and nanoscale of the crystallites allow densification levels that are highly competitive when compared to BaZrO₃-based materials formed by alternative synthesis techniques documented in the literature.     

Thermal analysis and thermal expansion studies on high density YBa2−xLaxCu3O7−δ, 0x0.2

The compositions in the YBa_2−xLa_xCu₃O_7−δ (0x0.2) system were prepared by the solid state reaction, employing a novel high-temperature oxygen sintering route. The modified sintering route yields dense slab like microstructures with large grains. The decomposition (incongruent melting) temperature of the YBa₂Cu₃O_7−δ (Y-123) phase was found to shift to higher temperatures with increasing oxygen partial pressure and lanthanum content. Structure remained orthorhombic up to x=0.2 with a decrease in the orthorhombic strain ((b−a)/b). Iodometric titration indicated a systematic increase in the oxygen content with increasing lanthanum content. Thermo-gravimetric studies in various oxygen partial pressures revealed that the oxygen diffusion in to the YBa₂Cu₃O_7−δ (δ>0.5) lattice is an exothermic event and takes place at temperatures not less than 573 K. High-temperature thermal-expansion measurements in air indicated that the nonlinearity in thermal expansion behaviour was reduced by the substitution of lanthanum.     

High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte based PCMFCs with stable Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 μm in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm⁻², and a low polarization resistance of the electrodes of 0.08 Ω cm² was achieved at 700 °C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells.     

Oxygen evolution on nanocrystalline RuO2 and Ru0.9Ni0.1O2−δ electrodes – DEMS approach to reaction mechanism determination

The mechanism of the oxygen evolution on RuO₂ and Ru_0.9Ni_0.1O_2−δ anodes was studied in 0.1 M HClO₄ using ¹⁸labeling combined with differential electrochemical mass spectrometry (DEMS). It was shown that the mechanism of the oxygen evolution is potential sensitive. At potentials negative to 1.12 V vs. SCE all the evolved oxygen originates from the electrolyte solution. At higher potentials an additional mechanism involving an exchange of the oxygen between electrolyte and electrocatalyst starts to apply. The extent of this oxygen exchange mechanism reflects the chemical composition of the electrocatalyst and is significantly higher at Ru_0.9Ni_0.1O_2−δ electrodes.     

Orthorhombic–orthorhombic phase transitions in Nd2NiO4+δ (0.067≤δ≤0.224)

Variation of the phases of Nd₂NiO_4+δ with the excess oxygen concentration δ has been examined at room temperature in the range 0.067≤δ≤0.224 using the X-ray powder diffraction technique. The phases observed at room temperature are orthorhombic-I (0.21<δ≤0.224), orthorhombic-IV (0.175<δ≤0.21), orthorhombic-II (0.15<δ≤0.175), orthorhombic-II+quasi-tetragonal-I (0.10<δ≤0.15), and quasi-tetragonal-I (0.067<δ≤0.10).     

Electron doping effect on structural and magnetic phase transitions in Sr2−xNdxFeMoO6 double perovskites

Polycrystalline Sr_2−xNd_xFeMoO₆ (x=0.0, 0.1, 0.2, 0.4) materials have been synthesized by a citrate co-precipitation method and studied by neutron powder diffraction (NPD) and magnetization measurements. Rietveld analysis of the temperature-dependent NPD data shows that the compounds (x=0.0, 0.1, 0.2) crystallize in the tetragonal symmetry in the range 10-400 K and converts to cubic symmetry above 450 K. The unit cell volume increases with increasing Nd³⁺ concentration, which is an electronic effect in order to change the valence state of the B-site cations. Antisite defects at the Fe-Mo sublattice increases with the Nd³⁺ doping. The Curie temperature was increased from 430 K for x=0 to 443 K for x=0.4. The magnetic moment of the Fe-site decreases while the Mo-site moment increases with electron doping. The antiferromagnetic arrangement causes the system to show a net ferrimagnetic moment.     

Electron-doping through La-for-Sr substitution in (Sr1−xLax)2FeTaO6: Effects on the valences and ordering of the B-site cations, Fe and Ta

We have employed aliovalent A-site cation substitution, La^III-for-Sr^II, to dope the Sr(Fe_0.5Ta_0.5)O₃ perovskite oxide with electrons. Essentially single-phase samples of (Sr_1−xLa_x)(Fe_0.5Ta_0.5)O₃ were successfully synthesized up to x≈0.3 in a vacuum furnace at 1400 °C. The samples were found to crystallize (rather than with orthorhombic symmetry) in monoclinic space group P2₁/n that accounts for the partial ordering of the B-site cations, Fe and Ta. With increasing La-substitution level, x, the degree of Fe/Ta order was found to increase such that the La-richest compositions are best described by the B-site ordered double-perovskite formula, (Sr,La)₂FeTaO₆. From Fe L₃ and Ta L₃ XANES spectra it was revealed that upon electron doping the two B-site cations, Fe^III and Ta^V, are both prone to reduction. Magnetic susceptibility measurements showed spin-glass type behaviour for all the samples with a transition temperature slightly increasing with increasing x.     

Synthesis and characterization of La0.8Sr1.2Co0.5M0.5O4−δ (M=Fe, Mn)

The M⁴⁺-containing K₂NiF₄-type phases La_0.8Sr_1.2Co_0.5Fe_0.5O₄ and La_0.8Sr_1.2Co_0.5Mn_0.5O₄ have been synthesized by a sol–gel procedure and characterized by X-ray powder diffraction, thermal analysis, neutron powder diffraction and Mössbauer spectroscopy. Oxide ion vacancies are created in these materials via reduction of M⁴⁺ to M³⁺ and of Co³⁺ to Co²⁺. The vacancies are confined to the equatorial planes of the K₂NiF₄-type structure. A partial reduction of Mn³⁺ to Mn²⁺ also occurs to achieve the oxygen stoichiometry in La_0.8Sr_1.2Co_0.5Mn_0.5O_3.6. La_0.8Sr_1.2Co_0.5Fe_0.5O_3.65 contains Co²⁺ and Fe³⁺ ions which interact antiferromagnetically and result in noncollinear magnetic order consistent with the tetragonal symmetry. Competing ferromagnetic and antiferromagnetic interactions in La_0.8Sr_1.2Co_0.5Fe_0.5O₄, La_0.8Sr_1.2Co_0.5Mn_0.5O₄ and La_0.8Sr_1.2Co_0.5Mn_0.5O_3.6 induce spin glass properties in these phases.     

La0.6Sr1.4MnO4 layered perovskite anode material for intermediate temperature solid oxide fuel cells

La_0.6Sr_1.4MnO₄ (LSMO₄) layered perovskite with K₂NiF₄ structure was prepared and evaluated as anode material for La_0.8Sr_0.2Ga_0.83Mg_0.17O_3 − δ (LSGM) electrolyte supported intermediate temperature solid oxide fuel cells (IT-SOFCs). X-ray diffraction results show that LSMO₄ is redox stability. Thermal expansion coefficient of LSMO₄ is close to that of LSGM electrolyte. By adopting LSMO₄ as anode and La_0.6Sr_0.4Co_0.8Fe_0.2O₃ (LSCF) as cathode, maxium power densities of 146.6, 110.9 mW cm^− 2 with H₂ fuel at 850, 800 °C and 47.3 mW cm^− 2 with CH₄ fuel at 800 °C were obtained, respectively. Further, the cell demonstrated a reasonably stable performance under 180 mA cm^− 2 for over 40 h with H₂ fuel at 800 °C.     

Temperature and composition dependent structural investigation of the defect perovskite series Sr1−xTi1−2xNb2xO3, 0≤x≤0.2

The crystal structure of the defect perovskite series Sr_1−xTi_1−2xNb_2xO₃ has been investigated over a range of temperatures using high-resolution synchrotron X-ray diffraction, neutron diffraction and electron diffraction. Three distinct regions were observed: 0<x≤0.125 was a solid solution of Sr_1−xTi_1−2xNb_2xO₃ with minor SrTiO₃ intergrowth, 0.125<x≤0.2 was a pure Sr_1−xTi_1−2xNb_2xO₃ solid solution adopting the cubic perovskite type structure (Pm3¯m) and for x>0.2 Sr_0.8Ti_0.6Nb_0.4O₃ and Sr₃TiNb₄O₁₅ formed a two phase region. The cubic structure for Sr_0.8Ti_0.6Nb_0.4O₃ was stable over the temperature range 90-1248 K and the thermal expansion co-efficient was determined to be 8.72(9)×10⁻⁶ K⁻¹. Electron diffraction studies revealed diffuse scattering due to local scale Ti/Nb displacements and slightly enhanced octahedral rotations that did not lead to long range order. The octahedral rotations were observed to ‘lock-in’ at temperatures below ∼75 K resulting in a tetragonal structure (I4/mcm) with anti-phase octahedral tilting about the c-axis.     

VNb9O25−δ—Synthesis, electrical conducting behaviour and density functional theory (DFT) calculation

In order to investigate the influence of the oxygen partial pressure (p(O₂)) on the electrical conductivity, VNb₉O₂₅ was prepared by thermal decomposition of freeze-dried oxalate precursors and by a solid state reaction of V₂O₅/Nb₂O₅ mixtures. The samples were characterised by X-ray diffraction, grain size analysis and scanning electron microscopy (SEM). The electrical conductivity of the n-type semiconductor VNb₉O_25−δ can be interpreted as an activated hopping process with a preferred localisation of charge carriers at V(IV) centres. The electronic structure of VNb₉O_25−δ was calculated within the framework of the local density approximation (LDA) to DFT. Partial reduction of V(V) centres causes localised vanadium states to appear inside the band gap. The calculated activation energy values are in good agreement with the experimental ones.     

Structure and Magnetism of Pr1−xSrxFeO3−δ

Crystal structure, redox, and magnetic properties for the Pr_1−xSr_xFeO_3−δ solid-solution phase have been studied. Oxidized samples (prepared in air at 900°C) crystallize in the GdFeO₃-type structure for 0≤x≤0.80, and probably in the Sr₈Fe₈O₂₃-type (unpublished) structure for x=0.90. Reduced samples (containing virtually only Fe³⁺) crystallize as the perovskite aristotype for x=0.50 and 0.67 with randomly distributed vacancies. The Fe⁴⁺ content increases linearly in the oxidized samples up to x≈0.70, whereupon it stabilizes at around 55%. Antiferromagnetic ordering of the G type is observed for oxidized samples (0≤x≤0.90) which show decreasing Néel temperature and ordered magnetic moment with increasing x, while the Néel temperature is nearly constant at 700 K for reduced samples. Electronic transitions for iron from an average-valence state via charge-separated to disproportionated states are proposed from anomalies in magnetic susceptibility curves in the temperature ranges 500–600 K and 150–185 K.     

Selective substitution of vanadium for molybdenum in Sr2(Fe1−xVx)MoO6 double perovskites

The crystal and magnetic structures of Sr₂(Fe_1−xV_x)MoO₆ (0.03?x?0.1) compounds are refined by alternately using X-ray powder diffraction (XRD) and neutron powder diffraction (NPD) data collected at room temperature. The refinement results reveal that the V atoms selectively occupy the Mo sites instead of the Fe sites for x?0.1. The 3d/4d cation ordering decreases with the increase of the V content. Slight distortions in the lattice and metal octahedra are shown at 300 K, and the distortions increase at 4 K. The magnetic structure at 4 K can be modeled equally well with the moments aligning along [001], [110] or [111] directions. The total moments derived from the NPD data for the [110] and [111] direction models agree well with the magnetic measurements, whereas the [001] model leads to a smaller total moment. Bond valence analysis indicates that Sr ions are properly located in the structure and Mo ions are compatible with both the Fe sites and the Mo sites. The electronic effects are suggested to be responsible for the selective occupation of the V on the Mo sites due to the different distortions of the FeO₆ and MoO₆ octahedra.     

High-pressure structural evolution of a perovskite solid solution (La1−x,Ndx)GaO3

The structural evolution with pressure of six perovskites in the system La_1−xNd_xGaO₃ with x=0.00, 0.06, 0.12, 0.20, 0.62 and 1.00 have been determined by single-crystal diffraction. At room pressure, all six samples have Pbnm symmetry. The room-pressure bulk moduli vary only slightly with composition, between K_0T=169(4) and 177(2) GPa, with . As pressure is increased there is significant compression of the octahedral Ga–O bonds, the tilts of the GaO₆ octahedra decrease and the structures evolve towards higher symmetry. At room conditions the average Ga–O bond length increases with increasing compositional parameter x. However, the GaO₆ become stiffer with increasing x; the Ga–O bonds thus become stiffer as they become longer. Bond strengths in the octahedra in perovskites are therefore not a simple function of bond lengths but depend also upon the extra-framework cation.Phase transitions to R-3c symmetry occur at 2.2 GPa in end-member LaGaO₃, at 5.5 GPa in the x=0.06 sample, at 7.8 GPa for x=0.12, and at 12 GPa for x=0.20. No evidence of the transition in the x=0.62 or 1.00 samples was found by X-ray diffraction to 9.4 or 8.0 GPa, respectively, or by Raman measurements of NdGaO₃ up to 16 GPa. The transition pressure therefore increases with increasing Nd content (increasing x) at approximately 0.45 GPa per 0.01 increment in x, at least up to x=0.20. Compression of the R-3c phase of LaGaO₃ above the transition results in no significant changes in the tilt angle of the octahedra. The structural behavior of all six samples at high pressures is the result of the GaO₆ octahedra being softer than the extra-framework (La, Nd)O₁₂ site. The results therefore demonstrate that the evolution of solid-solution perovskites at high pressures follow the same general principles recently elucidated for end-member compositions.     

Phase transition behavior for ZrW2−xMoxO8 compositions at elevated temperatures

A systematical study on cubic ZrW_2−xMo_xO₈ (x=0.73, 0.53, 0.33, 0.11) solid solutions reveals that their temperature-dependent phase transition behaviors are related to the Mo fraction x. A phase diagram of cubic ZrW_2−xMo_xO₈ solid solutions has been drawn over a wide temperature range (298–1473 K) on the basis of the temperature-dependent phase transition behaviors observed.     

Ln2Sr2PtO7+δ (Ln=La, Pr, and Nd): Three new Pt-containing [AnBn−1O3n]-type hexagonal perovskites

Polycrystalline samples of Ln₂Sr₂PtO_7+δ (Ln=La, Pr, Nd) were prepared by conventional solid state synthesis. The three compounds are new examples for n=2 members of the [A_nB_n−1O_3n] family of hexagonal perovskites containing platinum as the B-type cation. XRD Rietveld refinements show the platinates to crystallize in space group and, in the case of Pr and Nd, revealed a complete ordering of Ln/Sr on the two distinct A-type positions, while for La a partial disorder was observed. By XANES investigations at the Pt-L_III threshold the oxidation state +4 for platinum was found. Thermogravimetry revealed a small oxygen excess for Ln=La and Pr (δ=0.13 and 0.07), pointing to the presence of peroxide ions as already observed for isostructural Ru- and Ir-based compounds. UV–Vis measurements were done for the yellow lanthanum and the green neodymium compound. They revealed two optical band gaps of 2.52 and 3.05 eV, respectively. Magnetic measurements showed La₂Sr₂PtO_7+δ to be diamagnetic as expected for Pt⁴⁺ with low-spin configuration. For Ln=Pr and Nd the observed strong paramagnetism can be explained solely by the magnetic moments of the rare earths.     

A TEM investigation of the (Bi1−xSrx)FeO3−x/2, 0.2≤x≤0.67, solid solution and a suggested superspace structural description thereof

A careful transmission electron microscopy (TEM) investigation of an incommensurately modulated member of the (Bi_1−xSr_x)Fe³⁺O_3−x/2□_x/2, 0.2≤x≤0.67, solid solution has been carried out. High resolution (HR) TEM imaging is used to show the presence of at least 6-fold twinning on a rather fine (5 nm) scale. The (3+1)-d superspace group symmetry is suggested to be or one of the non-centrosymmetric sub-groups thereof, namely , , and . A superspace construction is then used to propose the nature of the local compositional ordering and, hence, of the oxygen-deficient slab that intergrows with the perovskite slab to produce the observed solid solution phase. The proposed compositional superspace atomic surfaces can be used to produce model structures at any composition within the solid solution range.     

Sol–gel derived nano-crystalline CaSnO3 as high capacity anode material for Li-ion batteries

CaSnO₃ with the distorted-perovskite structure was prepared by sol–gel and high temperature solid-state reaction and electrochemical properties were studied in cell with Li as counter electrode. The sol–gel method gave uniform nano-crystallites (200–300 nm) of CaSnO₃ and was shown to deliver a reversible capacity of 380 mAh/g (0.005–1.0 V; 60 mA/g) with good cycling stability up to 45 cycles. The observed capacity involved in the first-discharge and the reversible capacity values during subsequent charge–discharge cycles show that the electrochemical process in CaSnO₃ is similar to other Sn-containing mixed oxide systems, viz., an initial structural reduction with Sn-metal formation followed by reversible Li–Sn alloy formation. The performance with respect to the attainable capacity, its retention on charge–discharge cycling and rate capability is better than the previously reported best-performing bulk Sn-oxide or ATCO starting materials which reveals that the perovskite structure and Ca-ion play a beneficial role.