Micromechanical cantilever technique: a tool for investigating the swelling of polymer brushes

Polymer brush coatings are well-known for their ability to tailor surface properties in a wide range of applications from colloid stabilization to medicine. In most cases, the brushes are used in solution. Consequently, efforts were expended to experimentally investigate or theoretically predict the swelling behavior of the brushes in solvents of different qualities. Here, we show that the micromechanical cantilever (MC) sensor technique is a tool to perform time-resolved physicochemical investigations of thin layers such as polymer brushes. Complementary to scattering techniques, which measure the thickness, the MC sensor technique provides information about changes in the internal pressure of the brushes during a swelling and deswelling process. We show that the kinetics of both swelling and deswelling are dependent on solvent quality. Comparing the measured data with its thickness evolution, which was calculated based on the Flory-Huggins theory, we found that only the first 10% of the thickness increase of the polymer brush results in a significant pressure increase inside the polymer brush layer.     

Affinity adhesion of carbohydrate particles and yeast cells to boronate-containing polymer brushes grafted onto siliceous supports

Cross-linked agarose particles (Sepharose CL-6B) and baker's yeast cells were found to adhere to siliceous supports end-grafted with boronate-containing copolymers (BCCs) of N,N-dimethylacrylamide at pH> or =7.5, due to boronate interactions with surface carbohydrates of the particles and the cells. These interactions were registered both on macroscopic and on molecular levels: the BCCs spontaneously adsorbed on the agarose gel at pH> or =7.5, with adsorption increasing with pH. Agarose particles and yeast cells stained with Procion Red HE-3B formed stable, monolayer-like structures at pH 8.0, whereas at pH 7.0-7.8 the structures on the copolymer-grafted supports were less stable and more random. At pH 9.0, 50 % saturation of the surface with adhering cells was attained in 2 min. Stained cells formed denser and more stable layers on the copolymer-grafted supports than they did on supports modified with self-assembled organosilane layers derivatized with low-molecular-weight boronate, presumably due to a higher reactivity of the grafted BCCs. Quantitative detachment of adhered particles and cells could be achieved by addition of 20 mM fructose--a strong competitor for binding to boronates--at pH 7.0-9.0. Regeneration of the grafted supports allowed several sequential adhesion and detachment cycles with stained yeast cells. Affinity adhesion of micron-sized carbohydrate particles to boronate-containing polymer brushes fixed on solid supports is discussed as a possible model system suggesting a new approach to isolation and separation of living cells.     

An experimental-theoretical analysis of protein adsorption on peptidomimetic polymer brushes

Surface-grafted water-soluble polymer brushes are being intensely investigated for preventing protein adsorption to improve biomedical device function, prevent marine fouling, and enable applications in biosensing and tissue engineering. In this contribution, we present an experimental-theoretical analysis of a peptidomimetic polymer brush system with regard to the critical brush density required for preventing protein adsorption at varying chain lengths. A mussel adhesive-inspired DOPA-Lys (DOPA = 3,4-dihydroxy-phenylalanine; Lys = lysine) pentapeptide surface grafting motif enabled aqueous deposition of our peptidomimetic polypeptoid brushes over a wide range of chain densities. Critical densities of 0.88 nm(-2) for a relatively short polypeptoid 10-mer to 0.42 nm(-2) for a 50-mer were identified from measurements of protein adsorption. The experiments were also compared with the protein adsorption isotherms predicted by a molecular theory. Excellent agreements in terms of both the polymer brush structure and the critical chain density were obtained. Furthermore, atomic force microscopy (AFM) imaging is shown to be useful in verifying the critical brush density for preventing protein adsorption. The present coanalysis of experimental and theoretical results demonstrates the significance of characterizing the critical brush density in evaluating the performance of an antifouling polymer brush system. The high fidelity of the agreement between the experiments and molecular theory also indicate that the theoretical approach presented can aid in the practical design of antifouling polymer brush systems.     

Experiment and theory of low-pressure nitrogen adsorption in organic layers supported or grafted on inorganic adsorbents: toward a tool to characterize surfaces of hybrid organic/inorganic systems

We report experimental nitrogen adsorption isotherms of organics-coated silicas, which exhibit a low-pressure desorption branch that does not meet the adsorption branch upon emptying of the pores. To address the physical origin of such a hysteresis loop, we propose an equilibrium thermodynamic model that enables one to explain this phenomenon. The present model assumes that, upon adsorption, a small amount of nitrogen molecules penetrate within the organic layer and reach adsorption sites that are located on the inorganic surface, between the grafted or adsorbed organic molecules. The number of accessible adsorption sites thus varies with the increasing gas pressure, and then we assume that it stays constant upon desorption. Comparison with experimental data shows that our model captures the features of nitrogen adsorption on such hybrid organic/inorganic materials. In particular, in addition to predicting the shape of the adsorption isotherm, the model is able to estimate, with a reasonable number of adjustable parameters, the height of the low-pressure hysteresis loop and to assess in a qualitative fashion the local density of the organic chains at the surface of the material.     

Bioadhesive control of plasma proteins and blood cells from umbilical cord blood onto the interface grafted with zwitterionic polymer brushes

In this work, bioadhesive behavior of plasma proteins and blood cells from umbilical cord blood (UCB) onto zwitterionic poly(sulfobetaine methacrylate) (polySBMA) polymer brushes was studied. The surface coverage of polySBMA brushes on a hydrophobic polystyrene (PS) well plate with surface grafting weights ranging from 0.02 mg/cm(2) to 0.69 mg/cm(2) can be effectively controlled using the ozone pretreatment and thermal-induced radical graft-polymerization. The chemical composition, grafting structure, surface hydrophilicity, and hydration capability of prepared polySBMA brushes were determined to illustrate the correlations between grafting properties and blood compatibility of zwitterionic-grafted surfaces in contact with human UCB. The protein adsorption of fibrinogen in single-protein solutions and at complex medium of 100% UCB plasma onto different polySBMA brushes with different grafting coverage was measured by enzyme-linked immunosorbent assay (ELISA) with monoclonal antibodies. The grafting density of the zwitterionic brushes greatly affects the PS surface, thus controlling the adsorption of fibrinogen, the adhesion of platelets, and the preservation of hematopoietic stem and progenitor cells (HSPCs) in UCB. The results showed that PS surfaces grafted with polySBMA brushes possess controllable hydration properties through the binding of water molecules, regulating the bioadhesive and bioinert characteristics of plasma proteins and blood platelets in UCB. Interestingly, it was found that the polySBMA brushes with an optimized grafting weight of approximately 0.1 mg/cm(2) at physiologic temperatures show significant hydrated chain flexibility and balanced hydrophilicity to provide the best preservation capacity for HSPCs stored in 100% UCB solution for 2 weeks. This work suggests that, through controlling grafting structures, the hemocompatible nature of grafted zwitterionic polymer brushes makes them well suited to the molecular design of regulated bioadhesive interfaces for use in the preservation of HSPCs from human UCB.     

Influence of graft interface polarity on hydration/dehydration of grafted thermoresponsive polymer brushes and steroid separation using all-aqueous chromatography

We have prepared poly( N-isopropylacrylamide) (PIPAAm) brush-grafted surfaces with varied temperature-responsive hydrophobic properties through surface-initiated atom transfer radical polymerization (ATRP). These temperature-responsive surfaces were characterized by chromatographic analysis using modified silica beads as a chromatographic stationary phase in aqueous mobile phase. Mixed silane self-assembled monolayers (SAMs) comprising ATRP initiator and silanes with various terminal functional groups were formed on the silica bead surfaces. IPAAm was then polymerized by ATRP using the CuCl/CuCl2/Me6TREN catalyst system in 2-propanol at 25 degrees C for 16 h. The chromatographic retention behavior of steroids on the resulting PIPAAm brushes made on more polar silane components was distinct from that on more apolar silane interfaces. Retention times for steroids on PIPAAm mixed apolar silane graft interfaces were significantly longer than those on analogous polar silane interfaces due to enhanced dehydration of PIPAAm brushes on apolar silane-grafted surfaces. Changes in retention factor, k', on polar silane PIPAAm-grafted interfaces were relatively large compared to that on apolar PIPAAm grafted interfaces due to larger hydration/dehydration alterations of grafted PIPAAm brushes on the former surfaces. Applied step-temperature gradients from 50 to 10 degrees C show that PIPAAm brushes on polar silane interfaces tend to hydrate more, leading to shorter retention times. In conclusion, the polarity of the grafted interface significantly influences the grafted PIPAAm brush hydration/dehydration characteristics and subsequently also the temperature-modulated separation of bioactive compounds in all-aqueous chromatography.     

Direct observation of the phase transition for a poly(N-isopropylacryamide) layer grafted onto a solid surface by AFM and QCM-D

The temperature-induced structural changes of a thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) layer grafted onto a silica substrate were investigated in aqueous solution using an atomic force microscope (AFM) and a quartz crystal microbalance with dissipation (QCM-D). A PNIPAM layer was grafted onto the silicon wafer surface by free radical polymerization of NIPAM to obtain a high molecular weight polymer layer with low-grafting density overall. By AFM imaging, the transition of the grafted PNIPAM chains from a brush-like to a mushroom-like state was clearly visualized: The surface images of the plate were featureless at temperatures below the LCST commensurate with a brush-like layer, whereas above the LCST, a large number of domain structures with a characteristic size of approximately 100 nm were seen on the surface. Both frequency and dissipation data obtained using QCM-D showed a significant change at the LCST. Analysis of these data confirmed that the observed PNIPAM structural transition was caused by a collapse of the brush-like structure as a result of dehydration of the polymer chains.     

Solid/liquid interfacial tension as a tool to study stability of lysozyme on adsorption to solid surfaces

This work proposes the use of solid/liquid interfacial tension to study the stability of adsorbed lysozyme films on a solid surface using the contact angle of a liquid at the three phase contact line, in the presence of a denaturant, urea.Results suggest a direct correlation between this method with a standard technique like the fluorescence emission spectra and is measured with the same observable error as in the spectral methods. Further the technique provides a simple and direct handle to evaluate the homogeneity and degree of polarity of protein films on solid surfaces.     

Photoelectron spectroscopy studies of the functionalization of a silicon surface with a phosphorylcholine-terminated polymer grafted onto (3-aminopropyl)trimethoxysilane

The structure of a biomimetic phosphorylcholine (PC)-functionalized poly(trimethylene carbonate) (PC-PTMC-PC), linked to a silicon substrate through an aminolysis reaction at 120 degrees C with (3-aminopropyl)trimethoxysilane (APTMS), was studied using photoelectron spectroscopy. Two chemical states were found for the unreacted APTMS amine, a neutral state and a protonated state, where the protonated amine on average was situated closer to the silicon substrate than the neutral amine. The experiments also indicated the presence of a third chemical state, where amines interact with unreacted silanol groups. The PTMC chains of the grafted films were found to consist of only 2-3 repeat units, with the grafted chains enriched in the zwitterionic end group, suggesting that these groups are attracted to the surface. This was further supported by the experiments showing that the PC groups were situated deeper within the film.     

Nanoconfinement as a tool to study early stages of polymer crystallization

This article promotes the idea that crystallization experiments under confinement can be an interesting tool to learn more about the early stages of polymer crystallization in bulk systems. Based on various results from the recent literature, it is demonstrated that crystalline forms that are metastable, transient, or inaccessible in bulk samples can be easily obtained and studied in nanoscopic compartments. This is interesting in the light of the recent discussion about thermodynamic reasons for the temporary occurrence of a mesophase at the growth front of crystals in bulk polymers, in particular, about a hexagonally packed mesophase in polyethylene. The experimental findings for nanoconfined methylene sequences seem to support indirectly thermodynamic approaches explaining the occurrence of a mesophase based on the small thickness of the crystal at the growth front. A first estimate for the critical crystal thickness d_mc defining the transition from hexagonal to orthorhombic packing in case of confined methylene sequences is provided based on results for side chain polymers. Further perspectives of crystallization experiments on confined systems are discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1556–1561, 2008     

Temperature-programmed desorption as a tool for quantification of protein adsorption capacity in micro- and nanoporous materials

The protein adsorption capacity of porous sorbents is generally obtained by measuring the concentration of proteins desorbed from the materials after treatment by a detergent, or by measuring the decrease of protein concentration in the solution. These methods have some drawbacks and often lead to a low precision in the determination of the adsorption capacities. We describe in this paper a new method that allows to directly quantify the amount of proteins adsorbed on porous materials. This method is based on the quantitative analysis by mass spectrometry of some low mass gaseous species which evolve from the biomolecules during the heat treatment of a temperature-programmed desorption analysis (TPD-MS). The method has been applied to bovine serum albumin and cytochrome C adsorbed on an activated carbon. The adsorption uptake of the proteins on the carbon material could be measured by this direct analysis. A comparison with the depletion method was done, it shows that the two methods are complementary. The depletion method allows a determination of the total adsorption capacity, while the TPD-MS method focus on irreversible capacity.     

Competitive adsorption of fibrinogen and albumin onto polymer microspheres having hydrophilic/hydrophobic heterogeneous surface structures

The competitive adsorption of bovine fibrinogen (BFb) and bovine serum albumin onto polymer microspheres from the mixture solution was examined under various protein-to-microsphere ratios using various homopolymer microspheres and poly(2-hydroxyethyl methacrylate)/polystyrene composite microspheres having heterogeneous surface structures consisting of both hydrophilic and hydrophobic parts. They were produced by emulsifier-free (seeded) emulsion polymerizations. The selective adsorption of BFb was not observed for the homopolymer microspheres, but observed for the composite polymer microspheres having optimum compositions.Part CXXXVIII on the series Studies on Suspension and Emulsion     

Binding of dl-tryptophan to BSA adsorbed in multilayers by polymer chains grafted onto a porous hollow-fiber membrane in a permeation mode

An anion-exchange-group-containing porous membrane in the form of a hollow fiber was prepared to immobilize bovine serum albumin (BSA) as a chiral selector. First, an epoxy-group-containing polymer chain was grafted onto the pore surface of the polyethylene porous hollow-fiber membrane pre-irradiated with an electron beam. Second, the epoxy group was converted to diethylamino and 2-hydroxyethylamino groups. Third, a BSA solution was forced to permeate through the pores of the membrane. As a result, 190 mg BSA per gram of membrane, which amounted to a degree of multilayer binding of about four, were immobilized. Subsequently, a racemic solution of tryptophan (0.02 mM) was forced to permeate through the BSA-multilayered porous membrane at a flow rate ranging from 10 to 80 ml/h. A two-stage stepwise concentration change of tryptophan in the effluent was observed due to independent chiral recognition of d- and l-tryptophan by BSA adsorbed in multilayers within the graft chains.     

Synthesis and characterization of thermosensitive interpenetrating polymer networks based on N-isopropylacrylamide/N-acryloxysuccinimide, crosslinked with polylysine, grafted onto polypropylene

Interpenetrating polymer networks (IPNs) based on poly (N-isopropylacrylamide), (PNIPAAm) and poly (N-acryloxysuccinimide) (PNAS), grafted onto polypropylene (PP), were synthesized in three consecutive steps using ionizing radiation in the first and second steps and chemical reaction in third one. In the first step a thermosensitive graft copolymer of NIPAAm onto PP film was obtained by gamma radiation with a ⁶⁰Co source. The grafted side chains of PNIPAAm were then crosslinked with gamma radiation to give net-[PP-g-NIPAAm]. The secondary network was obtained in situ by chemical crosslinking between PNAS and polylysine (pLys). The PP-g-IPNs exhibited the lower critical solution temperature (LCST) at around 32 °C. Based on its thermoreversible behavior, this system could be used for immobilization of biomolecules. The phase transition temperature (LCST) and network properties of the IPNs were measured by swelling behavior. Additional characterization by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and infrared (FTIR-ATR) determinations are reported.     

On the stability of the polymer brushes formed by adsorption of ionomer complexes on hydrophilic and hydrophobic surfaces

We have studied the effect of normal forces and shear forces on the stability and functionality of a polymer brush layer formed upon adsorption of polymeric micelles on hydrophilic and hydrophobic surfaces. The micelles consist of oppositely charged polyelectrolyte blocks (poly(acrylic acid) and poly(N-methyl 2-vinyl pyridinium iodide), and a neutral block (poly(vinyl alcohol)) or neutral grafts (poly(ethylene oxide)). The strength of the attachment of the micellar layers to various substrates was evaluated with Atomic Force Microscopy. Flow cell experiments allowed for the evaluation of long-term stability of coatings in lateral flow. Fixed angle optical reflectometry was used to quantify protein (BSA) adsorption on the micellar layers after their exposure to flow. The results show that adsorbed micellar layers are relatively weakly attached to hydrophobic surfaces and much stronger to hydrophilic surfaces, which has a significant impact on their stability. Adsorbed layers maintain their ability to suppress protein adsorption on hydrophilic surfaces but not on hydrophobic surfaces. Due to the relatively weak attachment to hydrophobic surfaces the structure of adsorbed layers may easily be disrupted by lateral forces, such that the complex coacervate-brush structure no longer exists.     

Diffuse reflectance infrared Fourier transform spectroscopy as a tool to characterise water in adsorption/confinement situations

We present experimental data acquired by diffuse reflectance infrared spectroscopy in the mid-IR (4000-400 cm(-1)), on micrometric-sized mineral grain powders. The spectral evolution of the OH-stretching band is followed when the adsorbed water film is thinned under dry conditions, from high to low hydration states. The IR bands are found to be characteristic of the degree of adsorption/confinement of the liquid water. The OH-stretching band is shifted toward shorter wavenumbers than in bulk water, showing that a significant portion of adsorbed water has a higher intermolecular bonding energy. Complementary treatment of the kinetics of water desorption, varying with the surface forces in the water film, confirms the relationships of these bands with the constrained water state. We distinguish different water types obeying liquid-liquid interactions (free and capillary water) or dominated by solid-water interactions (confined and adsorbed water). Part of this study is devoted to mesoporous silica MCM-41, of interest due to the restricted geometries of its mesopores (4.7 nm) favouring the confined water state. The methodology allows us to distinguish bulk and adsorbed/confined water, using spectral analysis coupled with an understanding of the dynamic behaviour of the desorption process.     

Collapse and swelling of poly(N‐isopropylacrylamide‐co‐sodium acrylate) copolymer brushes grafted on a flat SiO2 surface

Poly(N‐isopropylacrylamide‐co‐sodium acrylate) copolymer brushes grafted on SiO₂‐coated quartz crystal surface were prepared with a surface‐immobilized initiator. The collapse and swelling of the thermally sensitive copolymer brushes in water were studied with quartz crystal microbalance in situ. The frequency and dissipation changes with the temperature increasing in the range 20–38 °C indicate that the brushes undergo a continuous collapse transition. Our results show that the copolymer brushes collapse to a state where the brushes were prepared. A hysteresis was observed in the cooling process. Fourier transform infrared (FTIR) results revealed that the formation of some additional hydrogen bonds within the copolymer chains at their collapsed state is responsible for the hysteresis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 770–778, 2006